@@ -81,10 +81,10 @@ restart when the system is resumed. This requires coordination between the
camera sensor and the rest of the camera pipeline. Bridge drivers are
responsible for this coordination, and instruct camera sensors to stop and
restart streaming by calling the appropriate subdev operations
-(``.s_stream()``, ``.enable_streams()`` or ``.disable_streams()``). Camera
-sensor drivers shall therefore **not** keep track of the streaming state to
-stop streaming in the PM suspend handler and restart it in the resume handler.
-Drivers should in general not implement the system PM handlers.
+(``.enable_streams()`` or ``.disable_streams()``). Camera sensor drivers shall
+therefore **not** keep track of the streaming state to stop streaming in the PM
+suspend handler and restart it in the resume handler. Drivers should in general
+not implement the system PM handlers.
Camera sensor drivers shall **not** implement the subdev ``.s_power()``
operation, as it is deprecated. While this operation is implemented in some
@@ -49,11 +49,14 @@ Link frequency
The :ref:`V4L2_CID_LINK_FREQ <v4l2-cid-link-freq>` control is used to tell the
receiver the frequency of the bus (i.e. it is not the same as the symbol rate).
-``.s_stream()`` callback
-^^^^^^^^^^^^^^^^^^^^^^^^
+``.enable_streams()`` and ``.disable_streams()`` callbacks
+^^^^^^^^^^^^^^^^^^^^^^^^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-The struct struct v4l2_subdev_video_ops->s_stream() callback is used by the
-receiver driver to control the transmitter driver's streaming state.
+The struct v4l2_subdev_pad_ops->enable_streams() and struct
+v4l2_subdev_pad_ops->disable_streams() callbacks are used by the receiver driver
+to control the transmitter driver's streaming state. These callbacks may not be
+called directly, but by using ``v4l2_subdev_enable_streams()`` and
+``v4l2_subdev_disable_streams()``.
CSI-2 transmitter drivers
@@ -127,7 +130,7 @@ Stopping the transmitter
^^^^^^^^^^^^^^^^^^^^^^^^
A transmitter stops sending the stream of images as a result of
-calling the ``.s_stream()`` callback. Some transmitters may stop the
+calling the ``.disable_streams()`` callback. Some transmitters may stop the
stream at a frame boundary whereas others stop immediately,
effectively leaving the current frame unfinished. The receiver driver
should not make assumptions either way, but function properly in both
@@ -450,8 +450,9 @@ enum v4l2_subdev_pre_streamon_flags {
* already started or stopped subdev. Also see call_s_stream wrapper in
* v4l2-subdev.c.
*
- * New drivers should instead implement &v4l2_subdev_pad_ops.enable_streams
- * and &v4l2_subdev_pad_ops.disable_streams operations, and use
+ * This callback is DEPRECATED. New drivers should instead implement
+ * &v4l2_subdev_pad_ops.enable_streams and
+ * &v4l2_subdev_pad_ops.disable_streams operations, and use
* v4l2_subdev_s_stream_helper for the &v4l2_subdev_video_ops.s_stream
* operation to support legacy users.
*
The scope of the s_stream video operation is now fully supported by {enable,disable}_streams. Explicitly document the s_stream() op as deprecated and update the related documentation. Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> --- Documentation/driver-api/media/camera-sensor.rst | 8 ++++---- Documentation/driver-api/media/tx-rx.rst | 13 ++++++++----- include/media/v4l2-subdev.h | 5 +++-- 3 files changed, 15 insertions(+), 11 deletions(-)