| Message ID | 20241029091042.337729-1-hpa@redhat.com (mailing list archive) |
|---|---|
| State | New |
| Headers | show |
| Series | [v6] media: Add t4ka3 camera sensor driver | expand |
Hi Kate, On 29-Oct-24 10:10 AM, Kate Hsuan wrote: > Add the t4ka3 driver from: > https://github.com/kitakar5525/surface3-atomisp-cameras.git > > With many cleanups / changes (almost a full rewrite) to make it suitable > for upstream: > > * Remove the VCM and VCM-OTP support, the mainline kernel models VCMs and > calibration data eeproms as separate v4l2-subdev-s. > > * Remove the integration-factor t4ka3_get_intg_factor() support and IOCTL, > this provided info to userspace through an atomisp private IOCTL. > > * Turn atomisp specific exposure/gain IOCTL into standard v4l2 controls. > > * Use normal ACPI power-management in combination with runtime-pm support > instead of atomisp specific GMIN power-management code. > > * Turn into a standard V4L2 sensor driver using > v4l2_async_register_subdev_sensor(). > > * Add vblank, hblank, and link-freq controls; drop get_frame_interval(). > > * Use CCI register helpers. > > * Calculate values for modes instead of using fixed register-value lists, > allowing arbritrary modes. > > * Add get_selection() and set_selection() support > > * Add a CSI2 bus configuration check > > This been tested on a Xiaomi Mipad2 tablet which has a T4KA3 sensor with > DW9761 VCM as back sensor. I tested this with the atomisp libcamera pipeline handler I have been working on and this is missing the mandatory pixel_rate control. That and it would be nice to also parse the properties indicating if this is a back or front camera. Attached is a patch which adds both, can you do a v7 with these changes squashed in ? Regards, Hans > > Co-developed-by: Hans de Goede <hdegoede@redhat.com> > Signed-off-by: Hans de Goede <hdegoede@redhat.com> > Signed-off-by: Kate Hsuan <hpa@redhat.com> > --- > Changes in v6: > 1. t4ka3_s_config() was removed. > 2. The unused macros were removed. > 3. The runtime pm initial flow was improved. > 4. In remove(), if the device is not in the "suspend" state, the device > will be manually turned off. > > Changes in v5: > 1. Improved Kconfig help description. > > Changes in v4: > 1. Another CI issue fixes. > > Changes in v3: > 1. Fix the issues reported by the CI system. > > Changes in v2: > 1. The regmap information was obtained before configuring runtime PM so > probe() can return without disabling runtime PM. > 2. In t4ka3_s_stream(), return -EBUSY when the streaming is enabled. > --- > drivers/media/i2c/Kconfig | 12 + > drivers/media/i2c/Makefile | 1 + > drivers/media/i2c/t4ka3.c | 1099 ++++++++++++++++++++++++++++++++++++ > 3 files changed, 1112 insertions(+) > create mode 100644 drivers/media/i2c/t4ka3.c > > diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig > index 8ba096b8ebca..6ec51f969b32 100644 > --- a/drivers/media/i2c/Kconfig > +++ b/drivers/media/i2c/Kconfig > @@ -690,6 +690,18 @@ config VIDEO_S5K6A3 > This is a V4L2 sensor driver for Samsung S5K6A3 raw > camera sensor. > > +config VIDEO_T4KA3 > + tristate "Toshiba T4KA3 sensor support" > + depends on ACPI || COMPILE_TEST > + depends on GPIOLIB > + select V4L2_CCI_I2C > + help > + This is a Video4Linux2 sensor driver for the Toshiba T4KA3 8 MP > + camera sensor. > + > + To compile this driver as a module, choose M here: the > + module will be called t4ka3. > + > config VIDEO_VGXY61 > tristate "ST VGXY61 sensor support" > select V4L2_CCI_I2C > diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile > index fbb988bd067a..ad67ea33ce37 100644 > --- a/drivers/media/i2c/Makefile > +++ b/drivers/media/i2c/Makefile > @@ -129,6 +129,7 @@ obj-$(CONFIG_VIDEO_SAA717X) += saa717x.o > obj-$(CONFIG_VIDEO_SAA7185) += saa7185.o > obj-$(CONFIG_VIDEO_SONY_BTF_MPX) += sony-btf-mpx.o > obj-$(CONFIG_VIDEO_ST_MIPID02) += st-mipid02.o > +obj-$(CONFIG_VIDEO_T4KA3) += t4ka3.o > obj-$(CONFIG_VIDEO_TC358743) += tc358743.o > obj-$(CONFIG_VIDEO_TC358746) += tc358746.o > obj-$(CONFIG_VIDEO_TDA1997X) += tda1997x.o > diff --git a/drivers/media/i2c/t4ka3.c b/drivers/media/i2c/t4ka3.c > new file mode 100644 > index 000000000000..ee4455a5e8e4 > --- /dev/null > +++ b/drivers/media/i2c/t4ka3.c > @@ -0,0 +1,1099 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Support for T4KA3 8M camera sensor. > + * > + * Copyright (C) 2015 Intel Corporation. All Rights Reserved. > + * Copyright (C) 2016 XiaoMi, Inc. > + * Copyright (C) 2024 Hans de Goede <hansg@kernel.org> > + */ > + > +#include <linux/acpi.h> > +#include <linux/bits.h> > +#include <linux/delay.h> > +#include <linux/dev_printk.h> > +#include <linux/device.h> > +#include <linux/err.h> > +#include <linux/errno.h> > +#include <linux/gpio/consumer.h> > +#include <linux/i2c.h> > +#include <linux/mod_devicetable.h> > +#include <linux/mutex.h> > +#include <linux/pm_runtime.h> > +#include <linux/regmap.h> > +#include <linux/types.h> > + > +#include <media/media-entity.h> > +#include <media/v4l2-async.h> > +#include <media/v4l2-cci.h> > +#include <media/v4l2-common.h> > +#include <media/v4l2-ctrls.h> > +#include <media/v4l2-fwnode.h> > +#include <media/v4l2-subdev.h> > + > +#define T4KA3_NATIVE_WIDTH 3280 > +#define T4KA3_NATIVE_HEIGHT 2464 > +#define T4KA3_NATIVE_START_LEFT 0 > +#define T4KA3_NATIVE_START_TOP 0 > +#define T4KA3_ACTIVE_WIDTH 3280 > +#define T4KA3_ACTIVE_HEIGHT 2460 > +#define T4KA3_ACTIVE_START_LEFT 0 > +#define T4KA3_ACTIVE_START_TOP 2 > +#define T4KA3_MIN_CROP_WIDTH 2 > +#define T4KA3_MIN_CROP_HEIGHT 2 > + > +#define T4KA3_PIXELS_PER_LINE 3440 > +#define T4KA3_LINES_PER_FRAME_30FPS 2492 > +#define T4KA3_FPS 30 > +#define T4KA3_PIXEL_RATE \ > + (T4KA3_PIXELS_PER_LINE * T4KA3_LINES_PER_FRAME_30FPS * T4KA3_FPS) > + > +/* > + * TODO this really should be derived from the 19.2 MHz xvclk combined > + * with the PLL settings. But without a datasheet this is the closest > + * approximation possible. > + * > + * link-freq = pixel_rate * bpp / (lanes * 2) > + * (lanes * 2) because CSI lanes use double-data-rate (DDR) signalling. > + * bpp = 10 and lanes = 4 > + */ > +#define T4KA3_LINK_FREQ ((u64)T4KA3_PIXEL_RATE * 10 / 8) > + > +/* For enum_frame_size() full-size + binned-/quarter-size */ > +#define T4KA3_FRAME_SIZES 2 > + > +#define T4KA3_REG_PRODUCT_ID_HIGH CCI_REG8(0x0000) > +#define T4KA3_REG_PRODUCT_ID_LOW CCI_REG8(0x0001) > +#define T4KA3_PRODUCT_ID 0x1490 > + > +#define T4KA3_REG_STREAM CCI_REG8(0x0100) > +#define T4KA3_REG_IMG_ORIENTATION CCI_REG8(0x0101) > +#define T4KA3_HFLIP_BIT BIT(0) > +#define T4KA3_VFLIP_BIT BIT(1) > +#define T4KA3_REG_PARAM_HOLD CCI_REG8(0x0104) > +#define T4KA3_REG_COARSE_INTEGRATION_TIME CCI_REG16(0x0202) > +#define T4KA3_COARSE_INTEGRATION_TIME_MARGIN 6 > +#define T4KA3_REG_DIGGAIN_GREEN_R CCI_REG16(0x020e) > +#define T4KA3_REG_DIGGAIN_RED CCI_REG16(0x0210) > +#define T4KA3_REG_DIGGAIN_BLUE CCI_REG16(0x0212) > +#define T4KA3_REG_DIGGAIN_GREEN_B CCI_REG16(0x0214) > +#define T4KA3_REG_GLOBAL_GAIN CCI_REG16(0x0234) > +#define T4KA3_MIN_GLOBAL_GAIN_SUPPORTED 0x0080 > +#define T4KA3_MAX_GLOBAL_GAIN_SUPPORTED 0x07ff > +#define T4KA3_REG_FRAME_LENGTH_LINES CCI_REG16(0x0340) /* aka VTS */ > +/* FIXME: need a datasheet to verify the min + max vblank values */ > +#define T4KA3_MIN_VBLANK 4 > +#define T4KA3_MAX_VBLANK 0xffff > +#define T4KA3_REG_PIXELS_PER_LINE CCI_REG16(0x0342) /* aka HTS */ > +/* These 2 being horz/vert start is a guess (no datasheet), always 0 */ > +#define T4KA3_REG_HORZ_START CCI_REG16(0x0344) > +#define T4KA3_REG_VERT_START CCI_REG16(0x0346) > +/* Always 3279 (T4KA3_NATIVE_WIDTH - 1, window is used to crop */ > +#define T4KA3_REG_HORZ_END CCI_REG16(0x0348) > +/* Always 2463 (T4KA3_NATIVE_HEIGHT - 1, window is used to crop */ > +#define T4KA3_REG_VERT_END CCI_REG16(0x034a) > +/* Output size (after cropping/window) */ > +#define T4KA3_REG_HORZ_OUTPUT_SIZE CCI_REG16(0x034c) > +#define T4KA3_REG_VERT_OUTPUT_SIZE CCI_REG16(0x034e) > +/* Window/crop start + size *after* binning */ > +#define T4KA3_REG_WIN_START_X CCI_REG16(0x0408) > +#define T4KA3_REG_WIN_START_Y CCI_REG16(0x040a) > +#define T4KA3_REG_WIN_WIDTH CCI_REG16(0x040c) > +#define T4KA3_REG_WIN_HEIGHT CCI_REG16(0x040e) > +#define T4KA3_REG_TEST_PATTERN_MODE CCI_REG8(0x0601) > +/* Unknown register at address 0x0900 */ > +#define T4KA3_REG_0900 CCI_REG8(0x0900) > +#define T4KA3_REG_BINNING CCI_REG8(0x0901) > +#define T4KA3_BINNING_VAL(_b) \ > + ({ typeof(_b) (b) = (_b); \ > + ((b) << 4) | (b); }) > + > +struct t4ka3_ctrls { > + struct v4l2_ctrl_handler handler; > + struct v4l2_ctrl *hflip; > + struct v4l2_ctrl *vflip; > + struct v4l2_ctrl *vblank; > + struct v4l2_ctrl *hblank; > + struct v4l2_ctrl *exposure; > + struct v4l2_ctrl *test_pattern; > + struct v4l2_ctrl *link_freq; > + struct v4l2_ctrl *gain; > +}; > + > +struct t4ka3_mode { > + struct v4l2_rect crop; > + struct v4l2_mbus_framefmt fmt; > + int binning; > + u16 win_x; > + u16 win_y; > +}; > + > +struct t4ka3_data { > + struct v4l2_subdev sd; > + struct media_pad pad; > + struct mutex lock; /* serialize sensor's ioctl */ > + struct t4ka3_ctrls ctrls; > + struct t4ka3_mode mode; > + struct device *dev; > + struct regmap *regmap; > + struct gpio_desc *powerdown_gpio; > + struct gpio_desc *reset_gpio; > + s64 link_freq[1]; > + int streaming; > +}; > + > +/* init settings */ > +static const struct cci_reg_sequence t4ka3_init_config[] = { > + {CCI_REG8(0x4136), 0x13}, > + {CCI_REG8(0x4137), 0x33}, > + {CCI_REG8(0x3094), 0x01}, > + {CCI_REG8(0x0233), 0x01}, > + {CCI_REG8(0x4B06), 0x01}, > + {CCI_REG8(0x4B07), 0x01}, > + {CCI_REG8(0x3028), 0x01}, > + {CCI_REG8(0x3032), 0x14}, > + {CCI_REG8(0x305C), 0x0C}, > + {CCI_REG8(0x306D), 0x0A}, > + {CCI_REG8(0x3071), 0xFA}, > + {CCI_REG8(0x307E), 0x0A}, > + {CCI_REG8(0x307F), 0xFC}, > + {CCI_REG8(0x3091), 0x04}, > + {CCI_REG8(0x3092), 0x60}, > + {CCI_REG8(0x3096), 0xC0}, > + {CCI_REG8(0x3100), 0x07}, > + {CCI_REG8(0x3101), 0x4C}, > + {CCI_REG8(0x3118), 0xCC}, > + {CCI_REG8(0x3139), 0x06}, > + {CCI_REG8(0x313A), 0x06}, > + {CCI_REG8(0x313B), 0x04}, > + {CCI_REG8(0x3143), 0x02}, > + {CCI_REG8(0x314F), 0x0E}, > + {CCI_REG8(0x3169), 0x99}, > + {CCI_REG8(0x316A), 0x99}, > + {CCI_REG8(0x3171), 0x05}, > + {CCI_REG8(0x31A1), 0xA7}, > + {CCI_REG8(0x31A2), 0x9C}, > + {CCI_REG8(0x31A3), 0x8F}, > + {CCI_REG8(0x31A4), 0x75}, > + {CCI_REG8(0x31A5), 0xEE}, > + {CCI_REG8(0x31A6), 0xEA}, > + {CCI_REG8(0x31A7), 0xE4}, > + {CCI_REG8(0x31A8), 0xE4}, > + {CCI_REG8(0x31DF), 0x05}, > + {CCI_REG8(0x31EC), 0x1B}, > + {CCI_REG8(0x31ED), 0x1B}, > + {CCI_REG8(0x31EE), 0x1B}, > + {CCI_REG8(0x31F0), 0x1B}, > + {CCI_REG8(0x31F1), 0x1B}, > + {CCI_REG8(0x31F2), 0x1B}, > + {CCI_REG8(0x3204), 0x3F}, > + {CCI_REG8(0x3205), 0x03}, > + {CCI_REG8(0x3210), 0x01}, > + {CCI_REG8(0x3216), 0x68}, > + {CCI_REG8(0x3217), 0x58}, > + {CCI_REG8(0x3218), 0x58}, > + {CCI_REG8(0x321A), 0x68}, > + {CCI_REG8(0x321B), 0x60}, > + {CCI_REG8(0x3238), 0x03}, > + {CCI_REG8(0x3239), 0x03}, > + {CCI_REG8(0x323A), 0x05}, > + {CCI_REG8(0x323B), 0x06}, > + {CCI_REG8(0x3243), 0x03}, > + {CCI_REG8(0x3244), 0x08}, > + {CCI_REG8(0x3245), 0x01}, > + {CCI_REG8(0x3307), 0x19}, > + {CCI_REG8(0x3308), 0x19}, > + {CCI_REG8(0x3320), 0x01}, > + {CCI_REG8(0x3326), 0x15}, > + {CCI_REG8(0x3327), 0x0D}, > + {CCI_REG8(0x3328), 0x01}, > + {CCI_REG8(0x3380), 0x01}, > + {CCI_REG8(0x339E), 0x07}, > + {CCI_REG8(0x3424), 0x00}, > + {CCI_REG8(0x343C), 0x01}, > + {CCI_REG8(0x3398), 0x04}, > + {CCI_REG8(0x343A), 0x10}, > + {CCI_REG8(0x339A), 0x22}, > + {CCI_REG8(0x33B4), 0x00}, > + {CCI_REG8(0x3393), 0x01}, > + {CCI_REG8(0x33B3), 0x6E}, > + {CCI_REG8(0x3433), 0x06}, > + {CCI_REG8(0x3433), 0x00}, > + {CCI_REG8(0x33B3), 0x00}, > + {CCI_REG8(0x3393), 0x03}, > + {CCI_REG8(0x33B4), 0x03}, > + {CCI_REG8(0x343A), 0x00}, > + {CCI_REG8(0x339A), 0x00}, > + {CCI_REG8(0x3398), 0x00} > +}; > + > +static const struct cci_reg_sequence t4ka3_pre_mode_set_regs[] = { > + {CCI_REG8(0x0112), 0x0A}, > + {CCI_REG8(0x0113), 0x0A}, > + {CCI_REG8(0x0114), 0x03}, > + {CCI_REG8(0x4136), 0x13}, > + {CCI_REG8(0x4137), 0x33}, > + {CCI_REG8(0x0820), 0x0A}, > + {CCI_REG8(0x0821), 0x0D}, > + {CCI_REG8(0x0822), 0x00}, > + {CCI_REG8(0x0823), 0x00}, > + {CCI_REG8(0x0301), 0x0A}, > + {CCI_REG8(0x0303), 0x01}, > + {CCI_REG8(0x0305), 0x04}, > + {CCI_REG8(0x0306), 0x02}, > + {CCI_REG8(0x0307), 0x18}, > + {CCI_REG8(0x030B), 0x01}, > +}; > + > +static const struct cci_reg_sequence t4ka3_post_mode_set_regs[] = { > + {CCI_REG8(0x0902), 0x00}, > + {CCI_REG8(0x4220), 0x00}, > + {CCI_REG8(0x4222), 0x01}, > + {CCI_REG8(0x3380), 0x01}, > + {CCI_REG8(0x3090), 0x88}, > + {CCI_REG8(0x3394), 0x20}, > + {CCI_REG8(0x3090), 0x08}, > + {CCI_REG8(0x3394), 0x10} > +}; > + > +static inline struct t4ka3_data *to_t4ka3_sensor(struct v4l2_subdev *sd) > +{ > + return container_of(sd, struct t4ka3_data, sd); > +} > + > +static inline struct t4ka3_data *ctrl_to_t4ka3(struct v4l2_ctrl *ctrl) > +{ > + return container_of(ctrl->handler, struct t4ka3_data, ctrls.handler); > +} > + > +/* T4KA3 default GRBG */ > +static const int t4ka3_hv_flip_bayer_order[] = { > + MEDIA_BUS_FMT_SGRBG10_1X10, > + MEDIA_BUS_FMT_SBGGR10_1X10, > + MEDIA_BUS_FMT_SRGGB10_1X10, > + MEDIA_BUS_FMT_SGBRG10_1X10, > +}; > + > +static const struct v4l2_rect t4ka3_default_crop = { > + .left = T4KA3_ACTIVE_START_LEFT, > + .top = T4KA3_ACTIVE_START_TOP, > + .width = T4KA3_ACTIVE_WIDTH, > + .height = T4KA3_ACTIVE_HEIGHT, > +}; > + > +static int t4ka3_detect(struct t4ka3_data *sensor, u16 *id); > + > +static void t4ka3_set_bayer_order(struct t4ka3_data *sensor, > + struct v4l2_mbus_framefmt *fmt) > +{ > + int hv_flip = 0; > + > + if (sensor->ctrls.vflip && sensor->ctrls.vflip->val) > + hv_flip += 1; > + > + if (sensor->ctrls.hflip && sensor->ctrls.hflip->val) > + hv_flip += 2; > + > + fmt->code = t4ka3_hv_flip_bayer_order[hv_flip]; > +} > + > +static int t4ka3_update_exposure_range(struct t4ka3_data *sensor) > +{ > + int exp_max = sensor->mode.fmt.height + sensor->ctrls.vblank->val - > + T4KA3_COARSE_INTEGRATION_TIME_MARGIN; > + > + return __v4l2_ctrl_modify_range(sensor->ctrls.exposure, 0, exp_max, > + 1, exp_max); > +} > + > +static struct v4l2_rect * > +__t4ka3_get_pad_crop(struct t4ka3_data *sensor, > + struct v4l2_subdev_state *state, > + unsigned int pad, > + enum v4l2_subdev_format_whence which) > +{ > + if (which == V4L2_SUBDEV_FORMAT_TRY) > + return v4l2_subdev_state_get_crop(state, pad); > + > + return &sensor->mode.crop; > +} > + > +static struct v4l2_mbus_framefmt * > +__t4ka3_get_pad_format(struct t4ka3_data *sensor, > + struct v4l2_subdev_state *sd_state, unsigned int pad, > + enum v4l2_subdev_format_whence which) > +{ > + if (which == V4L2_SUBDEV_FORMAT_TRY) > + return v4l2_subdev_state_get_format(sd_state, pad); > + > + return &sensor->mode.fmt; > +} > + > +static void t4ka3_fill_format(struct t4ka3_data *sensor, > + struct v4l2_mbus_framefmt *fmt, > + unsigned int width, unsigned int height) > +{ > + memset(fmt, 0, sizeof(*fmt)); > + fmt->width = width; > + fmt->height = height; > + fmt->field = V4L2_FIELD_NONE; > + fmt->colorspace = V4L2_COLORSPACE_SRGB; > + t4ka3_set_bayer_order(sensor, fmt); > +} > + > +static void t4ka3_calc_mode(struct t4ka3_data *sensor) > +{ > + int width = sensor->mode.fmt.width; > + int height = sensor->mode.fmt.height; > + int binning; > + > + if (width <= (sensor->mode.crop.width / 2) && > + height <= (sensor->mode.crop.height / 2)) > + binning = 2; > + else > + binning = 1; > + > + width *= binning; > + height *= binning; > + > + sensor->mode.binning = binning; > + sensor->mode.win_x = (sensor->mode.crop.left + > + (sensor->mode.crop.width - width) / 2) & ~1; > + sensor->mode.win_y = (sensor->mode.crop.top + > + (sensor->mode.crop.height - height) / 2) & ~1; > + /* > + * t4ka's window is done after binning, but must still be a multiple of 2 ? > + * Round up to avoid top 2 black lines in 1640x1230 (quarter res) case. > + */ > + sensor->mode.win_x = DIV_ROUND_UP(sensor->mode.win_x, binning); > + sensor->mode.win_y = DIV_ROUND_UP(sensor->mode.win_y, binning); > +} > + > +static void t4ka3_get_vblank_limits(struct t4ka3_data *sensor, int *min, int *max, int *def) > +{ > + *min = T4KA3_MIN_VBLANK + (sensor->mode.binning - 1) * sensor->mode.fmt.height; > + *max = T4KA3_MAX_VBLANK - sensor->mode.fmt.height; > + *def = T4KA3_LINES_PER_FRAME_30FPS - sensor->mode.fmt.height; > +} > + > +static int t4ka3_set_pad_format(struct v4l2_subdev *sd, > + struct v4l2_subdev_state *sd_state, > + struct v4l2_subdev_format *format) > +{ > + struct t4ka3_data *sensor = to_t4ka3_sensor(sd); > + struct v4l2_mbus_framefmt *try_fmt; > + const struct v4l2_rect *crop; > + unsigned int width, height; > + int min, max, def, ret = 0; > + > + crop = __t4ka3_get_pad_crop(sensor, sd_state, format->pad, format->which); > + > + /* Limit set_fmt max size to crop width / height */ > + width = clamp_val(ALIGN(format->format.width, 2), > + T4KA3_MIN_CROP_WIDTH, crop->width); > + height = clamp_val(ALIGN(format->format.height, 2), > + T4KA3_MIN_CROP_HEIGHT, crop->height); > + t4ka3_fill_format(sensor, &format->format, width, height); > + > + if (format->which == V4L2_SUBDEV_FORMAT_TRY) { > + try_fmt = v4l2_subdev_state_get_format(sd_state, 0); > + *try_fmt = format->format; > + return 0; > + } > + > + mutex_lock(&sensor->lock); > + > + if (sensor->streaming) { > + ret = -EBUSY; > + goto unlock; > + } > + > + sensor->mode.fmt = format->format; > + t4ka3_calc_mode(sensor); > + > + /* vblank range is height dependent adjust and reset to default */ > + t4ka3_get_vblank_limits(sensor, &min, &max, &def); > + ret = __v4l2_ctrl_modify_range(sensor->ctrls.vblank, min, max, 1, def); > + if (ret) > + goto unlock; > + > + ret = __v4l2_ctrl_s_ctrl(sensor->ctrls.vblank, def); > + if (ret) > + goto unlock; > + > + def = T4KA3_ACTIVE_WIDTH - sensor->mode.fmt.width; > + ret = __v4l2_ctrl_modify_range(sensor->ctrls.hblank, def, def, 1, def); > + if (ret) > + goto unlock; > + ret = __v4l2_ctrl_s_ctrl(sensor->ctrls.hblank, def); > + if (ret) > + goto unlock; > + > + /* exposure range depends on vts which may have changed */ > + ret = t4ka3_update_exposure_range(sensor); > + if (ret) > + goto unlock; > + > +unlock: > + mutex_unlock(&sensor->lock); > + return ret; > +} > + > +/* Horizontal flip the image. */ > +static int t4ka3_t_hflip(struct v4l2_subdev *sd, int value) > +{ > + struct t4ka3_data *sensor = to_t4ka3_sensor(sd); > + int ret; > + u64 val; > + > + if (sensor->streaming) > + return -EBUSY; > + > + val = value ? T4KA3_HFLIP_BIT : 0; > + > + ret = cci_update_bits(sensor->regmap, T4KA3_REG_IMG_ORIENTATION, > + T4KA3_HFLIP_BIT, val, NULL); > + if (ret) > + return ret; > + > + t4ka3_set_bayer_order(sensor, &sensor->mode.fmt); > + return 0; > +} > + > +/* Vertically flip the image */ > +static int t4ka3_t_vflip(struct v4l2_subdev *sd, int value) > +{ > + struct t4ka3_data *sensor = to_t4ka3_sensor(sd); > + int ret; > + u64 val; > + > + if (sensor->streaming) > + return -EBUSY; > + > + val = value ? T4KA3_VFLIP_BIT : 0; > + > + ret = cci_update_bits(sensor->regmap, T4KA3_REG_IMG_ORIENTATION, > + T4KA3_VFLIP_BIT, val, NULL); > + if (ret) > + return ret; > + > + t4ka3_set_bayer_order(sensor, &sensor->mode.fmt); > + return 0; > +} > + > +static int t4ka3_test_pattern(struct t4ka3_data *sensor, s32 value) > +{ > + return cci_write(sensor->regmap, T4KA3_REG_TEST_PATTERN_MODE, value, NULL); > +} > + > +static int t4ka3_detect(struct t4ka3_data *sensor, u16 *id) > +{ > + struct i2c_client *client = v4l2_get_subdevdata(&sensor->sd); > + struct i2c_adapter *adapter = client->adapter; > + u64 high, low; > + int ret = 0; > + > + /* i2c check */ > + if (!i2c_check_functionality(adapter, I2C_FUNC_I2C)) > + return -ENODEV; > + > + /* check sensor chip ID */ > + cci_read(sensor->regmap, T4KA3_REG_PRODUCT_ID_HIGH, &high, &ret); > + cci_read(sensor->regmap, T4KA3_REG_PRODUCT_ID_LOW, &low, &ret); > + if (ret) > + return ret; > + > + *id = (((u8)high) << 8) | (u8)low; > + if (*id != T4KA3_PRODUCT_ID) { > + dev_err(sensor->dev, "main sensor t4ka3 ID error\n"); > + return -ENODEV; > + } > + > + return 0; > +} > + > +static int t4ka3_s_ctrl(struct v4l2_ctrl *ctrl) > +{ > + struct t4ka3_data *sensor = ctrl_to_t4ka3(ctrl); > + int ret; > + > + /* Update exposure range on vblank changes */ > + if (ctrl->id == V4L2_CID_VBLANK) { > + ret = t4ka3_update_exposure_range(sensor); > + if (ret) > + return ret; > + } > + > + /* Only apply changes to the controls if the device is powered up */ > + if (!pm_runtime_get_if_in_use(sensor->sd.dev)) { > + t4ka3_set_bayer_order(sensor, &sensor->mode.fmt); > + return 0; > + } > + > + switch (ctrl->id) { > + case V4L2_CID_TEST_PATTERN: > + ret = t4ka3_test_pattern(sensor, ctrl->val); > + break; > + case V4L2_CID_VFLIP: > + ret = t4ka3_t_vflip(&sensor->sd, ctrl->val); > + break; > + case V4L2_CID_HFLIP: > + ret = t4ka3_t_hflip(&sensor->sd, ctrl->val); > + break; > + case V4L2_CID_VBLANK: > + ret = cci_write(sensor->regmap, T4KA3_REG_FRAME_LENGTH_LINES, > + sensor->mode.fmt.height + ctrl->val, NULL); > + break; > + case V4L2_CID_EXPOSURE: > + ret = cci_write(sensor->regmap, T4KA3_REG_COARSE_INTEGRATION_TIME, > + ctrl->val, NULL); > + break; > + case V4L2_CID_ANALOGUE_GAIN: > + ret = cci_write(sensor->regmap, T4KA3_REG_GLOBAL_GAIN, > + ctrl->val, NULL); > + break; > + default: > + ret = -EINVAL; > + break; > + } > + > + pm_runtime_put(sensor->sd.dev); > + return ret; > +} > + > +static int t4ka3_set_mode(struct t4ka3_data *sensor) > +{ > + int ret = 0; > + > + cci_write(sensor->regmap, T4KA3_REG_HORZ_OUTPUT_SIZE, sensor->mode.fmt.width, &ret); > + /* Write mode-height - 2 otherwise things don't work, hw-bug ? */ > + cci_write(sensor->regmap, T4KA3_REG_VERT_OUTPUT_SIZE, sensor->mode.fmt.height - 2, &ret); > + /* Note overwritten by __v4l2_ctrl_handler_setup() based on vblank ctrl */ > + cci_write(sensor->regmap, T4KA3_REG_FRAME_LENGTH_LINES, T4KA3_LINES_PER_FRAME_30FPS, &ret); > + cci_write(sensor->regmap, T4KA3_REG_PIXELS_PER_LINE, T4KA3_PIXELS_PER_LINE, &ret); > + /* Always use the full sensor, using window to crop */ > + cci_write(sensor->regmap, T4KA3_REG_HORZ_START, 0, &ret); > + cci_write(sensor->regmap, T4KA3_REG_VERT_START, 0, &ret); > + cci_write(sensor->regmap, T4KA3_REG_HORZ_END, T4KA3_NATIVE_WIDTH - 1, &ret); > + cci_write(sensor->regmap, T4KA3_REG_VERT_END, T4KA3_NATIVE_HEIGHT - 1, &ret); > + /* Set window */ > + cci_write(sensor->regmap, T4KA3_REG_WIN_START_X, sensor->mode.win_x, &ret); > + cci_write(sensor->regmap, T4KA3_REG_WIN_START_Y, sensor->mode.win_y, &ret); > + cci_write(sensor->regmap, T4KA3_REG_WIN_WIDTH, sensor->mode.fmt.width, &ret); > + cci_write(sensor->regmap, T4KA3_REG_WIN_HEIGHT, sensor->mode.fmt.height, &ret); > + /* Write 1 to unknown register 0x0900 */ > + cci_write(sensor->regmap, T4KA3_REG_0900, 1, &ret); > + cci_write(sensor->regmap, T4KA3_REG_BINNING, T4KA3_BINNING_VAL(sensor->mode.binning), &ret); > + > + return ret; > +} > + > +static int t4ka3_s_stream(struct v4l2_subdev *sd, int enable) > +{ > + struct t4ka3_data *sensor = to_t4ka3_sensor(sd); > + int ret; > + > + mutex_lock(&sensor->lock); > + > + if (sensor->streaming == enable) { > + dev_warn(sensor->dev, "Stream already %s\n", enable ? "started" : "stopped"); > + ret = -EBUSY; > + goto error_unlock; > + } > + > + if (enable) { > + ret = pm_runtime_get_sync(sensor->sd.dev); > + if (ret < 0) { > + dev_err(sensor->dev, "power-up err.\n"); > + goto error_unlock; > + } > + > + cci_multi_reg_write(sensor->regmap, t4ka3_init_config, > + ARRAY_SIZE(t4ka3_init_config), &ret); > + /* enable group hold */ > + cci_write(sensor->regmap, T4KA3_REG_PARAM_HOLD, 1, &ret); > + cci_multi_reg_write(sensor->regmap, t4ka3_pre_mode_set_regs, > + ARRAY_SIZE(t4ka3_pre_mode_set_regs), &ret); > + if (ret) > + goto error_powerdown; > + > + ret = t4ka3_set_mode(sensor); > + if (ret) > + goto error_powerdown; > + > + ret = cci_multi_reg_write(sensor->regmap, t4ka3_post_mode_set_regs, > + ARRAY_SIZE(t4ka3_post_mode_set_regs), NULL); > + if (ret) > + goto error_powerdown; > + > + /* Restore value of all ctrls */ > + ret = __v4l2_ctrl_handler_setup(&sensor->ctrls.handler); > + if (ret) > + goto error_powerdown; > + > + /* disable group hold */ > + cci_write(sensor->regmap, T4KA3_REG_PARAM_HOLD, 0, &ret); > + cci_write(sensor->regmap, T4KA3_REG_STREAM, 1, &ret); > + if (ret) > + goto error_powerdown; > + > + sensor->streaming = 1; > + } else { > + ret = cci_write(sensor->regmap, T4KA3_REG_STREAM, 0, NULL); > + if (ret) > + goto error_powerdown; > + > + ret = pm_runtime_put(sensor->sd.dev); > + if (ret) > + goto error_unlock; > + > + sensor->streaming = 0; > + } > + > + mutex_unlock(&sensor->lock); > + return ret; > + > +error_powerdown: > + pm_runtime_put(sensor->sd.dev); > +error_unlock: > + mutex_unlock(&sensor->lock); > + return ret; > +} > + > +static int t4ka3_get_selection(struct v4l2_subdev *sd, > + struct v4l2_subdev_state *state, > + struct v4l2_subdev_selection *sel) > +{ > + struct t4ka3_data *sensor = to_t4ka3_sensor(sd); > + > + switch (sel->target) { > + case V4L2_SEL_TGT_CROP: > + mutex_lock(&sensor->lock); > + sel->r = *__t4ka3_get_pad_crop(sensor, state, sel->pad, > + sel->which); > + mutex_unlock(&sensor->lock); > + break; > + case V4L2_SEL_TGT_NATIVE_SIZE: > + case V4L2_SEL_TGT_CROP_BOUNDS: > + sel->r.top = 0; > + sel->r.left = 0; > + sel->r.width = T4KA3_NATIVE_WIDTH; > + sel->r.height = T4KA3_NATIVE_HEIGHT; > + break; > + case V4L2_SEL_TGT_CROP_DEFAULT: > + sel->r = t4ka3_default_crop; > + break; > + default: > + return -EINVAL; > + } > + > + return 0; > +} > + > +static int t4ka3_set_selection(struct v4l2_subdev *sd, > + struct v4l2_subdev_state *state, > + struct v4l2_subdev_selection *sel) > +{ > + struct t4ka3_data *sensor = to_t4ka3_sensor(sd); > + struct v4l2_mbus_framefmt *format; > + struct v4l2_rect *crop; > + struct v4l2_rect rect; > + > + if (sel->target != V4L2_SEL_TGT_CROP) > + return -EINVAL; > + > + /* > + * Clamp the boundaries of the crop rectangle to the size of the sensor > + * pixel array. Align to multiples of 2 to ensure Bayer pattern isn't > + * disrupted. > + */ > + rect.left = clamp_val(ALIGN(sel->r.left, 2), > + T4KA3_NATIVE_START_LEFT, T4KA3_NATIVE_WIDTH); > + rect.top = clamp_val(ALIGN(sel->r.top, 2), > + T4KA3_NATIVE_START_TOP, T4KA3_NATIVE_HEIGHT); > + rect.width = clamp_val(ALIGN(sel->r.width, 2), > + T4KA3_MIN_CROP_WIDTH, T4KA3_NATIVE_WIDTH); > + rect.height = clamp_val(ALIGN(sel->r.height, 2), > + T4KA3_MIN_CROP_HEIGHT, T4KA3_NATIVE_HEIGHT); > + > + /* Make sure the crop rectangle isn't outside the bounds of the array */ > + rect.width = min_t(unsigned int, rect.width, > + T4KA3_NATIVE_WIDTH - rect.left); > + rect.height = min_t(unsigned int, rect.height, > + T4KA3_NATIVE_HEIGHT - rect.top); > + > + crop = __t4ka3_get_pad_crop(sensor, state, sel->pad, sel->which); > + > + mutex_lock(&sensor->lock); > + > + *crop = rect; > + > + if (rect.width != crop->width || rect.height != crop->height) { > + /* > + * Reset the output image size if the crop rectangle size has > + * been modified. > + */ > + format = __t4ka3_get_pad_format(sensor, state, sel->pad, > + sel->which); > + format->width = rect.width; > + format->height = rect.height; > + if (sel->which == V4L2_SUBDEV_FORMAT_ACTIVE) > + t4ka3_calc_mode(sensor); > + } > + > + mutex_unlock(&sensor->lock); > + > + sel->r = rect; > + > + return 0; > +} > + > +static int > +t4ka3_enum_mbus_code(struct v4l2_subdev *sd, > + struct v4l2_subdev_state *sd_state, > + struct v4l2_subdev_mbus_code_enum *code) > +{ > + if (code->index) > + return -EINVAL; > + > + code->code = MEDIA_BUS_FMT_SGRBG10_1X10; > + return 0; > +} > + > +static int t4ka3_enum_frame_size(struct v4l2_subdev *sd, > + struct v4l2_subdev_state *sd_state, > + struct v4l2_subdev_frame_size_enum *fse) > +{ > + struct t4ka3_data *sensor = to_t4ka3_sensor(sd); > + struct v4l2_rect *crop; > + > + if (fse->index >= T4KA3_FRAME_SIZES) > + return -EINVAL; > + > + crop = __t4ka3_get_pad_crop(sensor, sd_state, fse->pad, fse->which); > + if (!crop) > + return -EINVAL; > + > + fse->min_width = crop->width / (fse->index + 1); > + fse->min_height = crop->height / (fse->index + 1); > + fse->max_width = fse->min_width; > + fse->max_height = fse->min_height; > + > + return 0; > +} > + > +static int > +t4ka3_get_pad_format(struct v4l2_subdev *sd, > + struct v4l2_subdev_state *sd_state, > + struct v4l2_subdev_format *fmt) > +{ > + struct t4ka3_data *sensor = to_t4ka3_sensor(sd); > + struct v4l2_mbus_framefmt *format = > + __t4ka3_get_pad_format(sensor, sd_state, fmt->pad, fmt->which); > + > + fmt->format = *format; > + return 0; > +} > + > +static int t4ka3_check_hwcfg(struct t4ka3_data *sensor) > +{ > + struct fwnode_handle *fwnode = dev_fwnode(sensor->dev); > + struct v4l2_fwnode_endpoint bus_cfg = { > + .bus_type = V4L2_MBUS_CSI2_DPHY, > + }; > + struct fwnode_handle *endpoint; > + unsigned int i; > + int ret; > + > + /* > + * Sometimes the fwnode graph is initialized by the bridge driver. > + * Bridge drivers doing this may also add GPIO mappings, wait for this. > + */ > + endpoint = fwnode_graph_get_next_endpoint(fwnode, NULL); > + if (!endpoint) > + return dev_err_probe(sensor->dev, -EPROBE_DEFER, > + "waiting for fwnode graph endpoint\n"); > + > + ret = v4l2_fwnode_endpoint_alloc_parse(endpoint, &bus_cfg); > + fwnode_handle_put(endpoint); > + if (ret) > + return ret; > + > + if (bus_cfg.bus.mipi_csi2.num_data_lanes != 4) { > + dev_err(sensor->dev, "only a 4-lane CSI2 config is supported"); > + ret = -EINVAL; > + goto out_free_bus_cfg; > + } > + > + if (!bus_cfg.nr_of_link_frequencies) { > + dev_err(sensor->dev, "no link frequencies defined\n"); > + ret = -EINVAL; > + goto out_free_bus_cfg; > + } > + > + for (i = 0; i < bus_cfg.nr_of_link_frequencies; i++) { > + if (bus_cfg.link_frequencies[i] == T4KA3_LINK_FREQ) > + break; > + } > + > + if (i == bus_cfg.nr_of_link_frequencies) { > + dev_err(sensor->dev, "supported link freq %llu not found\n", > + T4KA3_LINK_FREQ); > + ret = -EINVAL; > + goto out_free_bus_cfg; > + } > + > +out_free_bus_cfg: > + v4l2_fwnode_endpoint_free(&bus_cfg); > + > + return ret; > +} > + > +static int t4ka3_init_state(struct v4l2_subdev *sd, > + struct v4l2_subdev_state *sd_state) > +{ > + struct t4ka3_data *sensor = to_t4ka3_sensor(sd); > + > + *v4l2_subdev_state_get_crop(sd_state, 0) = t4ka3_default_crop; > + > + t4ka3_fill_format(sensor, v4l2_subdev_state_get_format(sd_state, 0), > + T4KA3_ACTIVE_WIDTH, T4KA3_ACTIVE_HEIGHT); > + return 0; > +} > + > +static const struct v4l2_ctrl_ops t4ka3_ctrl_ops = { > + .s_ctrl = t4ka3_s_ctrl, > +}; > + > +static const struct v4l2_subdev_video_ops t4ka3_video_ops = { > + .s_stream = t4ka3_s_stream, > +}; > + > +static const struct v4l2_subdev_pad_ops t4ka3_pad_ops = { > + .enum_mbus_code = t4ka3_enum_mbus_code, > + .enum_frame_size = t4ka3_enum_frame_size, > + .get_fmt = t4ka3_get_pad_format, > + .set_fmt = t4ka3_set_pad_format, > + .get_selection = t4ka3_get_selection, > + .set_selection = t4ka3_set_selection, > +}; > + > +static const struct v4l2_subdev_ops t4ka3_ops = { > + .video = &t4ka3_video_ops, > + .pad = &t4ka3_pad_ops, > +}; > + > +static const struct v4l2_subdev_internal_ops t4ka3_internal_ops = { > + .init_state = t4ka3_init_state, > +}; > + > +static int t4ka3_init_controls(struct t4ka3_data *sensor) > +{ > + const struct v4l2_ctrl_ops *ops = &t4ka3_ctrl_ops; > + struct t4ka3_ctrls *ctrls = &sensor->ctrls; > + struct v4l2_ctrl_handler *hdl = &ctrls->handler; > + int min, max, def; > + static const char * const test_pattern_menu[] = { > + "Disabled", > + "Solid White", > + "Color Bars", > + "Gradient", > + "Random Data", > + }; > + > + v4l2_ctrl_handler_init(hdl, 4); > + > + hdl->lock = &sensor->lock; > + > + ctrls->vflip = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_VFLIP, 0, 1, 1, 0); > + ctrls->hflip = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_HFLIP, 0, 1, 1, 0); > + > + ctrls->test_pattern = v4l2_ctrl_new_std_menu_items(hdl, ops, > + V4L2_CID_TEST_PATTERN, > + ARRAY_SIZE(test_pattern_menu) - 1, > + 0, 0, test_pattern_menu); > + ctrls->link_freq = v4l2_ctrl_new_int_menu(hdl, NULL, V4L2_CID_LINK_FREQ, > + 0, 0, sensor->link_freq); > + > + t4ka3_get_vblank_limits(sensor, &min, &max, &def); > + ctrls->vblank = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_VBLANK, min, max, 1, def); > + > + def = T4KA3_PIXELS_PER_LINE - sensor->mode.fmt.width; > + ctrls->hblank = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_HBLANK, > + def, def, 1, def); > + > + max = T4KA3_LINES_PER_FRAME_30FPS - T4KA3_COARSE_INTEGRATION_TIME_MARGIN; > + ctrls->exposure = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_EXPOSURE, > + 0, max, 1, max); > + > + ctrls->gain = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_ANALOGUE_GAIN, > + T4KA3_MIN_GLOBAL_GAIN_SUPPORTED, > + T4KA3_MAX_GLOBAL_GAIN_SUPPORTED, > + 1, T4KA3_MIN_GLOBAL_GAIN_SUPPORTED); > + > + if (hdl->error) > + return hdl->error; > + > + ctrls->vflip->flags |= V4L2_CTRL_FLAG_MODIFY_LAYOUT; > + ctrls->hflip->flags |= V4L2_CTRL_FLAG_MODIFY_LAYOUT; > + ctrls->link_freq->flags |= V4L2_CTRL_FLAG_READ_ONLY; > + ctrls->hblank->flags |= V4L2_CTRL_FLAG_READ_ONLY; > + > + sensor->sd.ctrl_handler = hdl; > + return 0; > +} > + > +static int t4ka3_pm_suspend(struct device *dev) > +{ > + struct t4ka3_data *sensor = dev_get_drvdata(dev); > + > + gpiod_set_value_cansleep(sensor->powerdown_gpio, 1); > + gpiod_set_value_cansleep(sensor->reset_gpio, 1); > + > + return 0; > +} > + > +static int t4ka3_pm_resume(struct device *dev) > +{ > + struct t4ka3_data *sensor = dev_get_drvdata(dev); > + u16 sensor_id; > + int ret; > + > + usleep_range(5000, 6000); > + > + gpiod_set_value_cansleep(sensor->powerdown_gpio, 0); > + gpiod_set_value_cansleep(sensor->reset_gpio, 0); > + > + /* waiting for the sensor after powering up */ > + msleep(20); > + > + ret = t4ka3_detect(sensor, &sensor_id); > + if (ret) { > + dev_err(sensor->dev, "sensor detect failed\n"); > + return ret; > + } > + > + return 0; > +} > + > +static DEFINE_RUNTIME_DEV_PM_OPS(t4ka3_pm_ops, t4ka3_pm_suspend, t4ka3_pm_resume, NULL); > + > +static void t4ka3_remove(struct i2c_client *client) > +{ > + struct v4l2_subdev *sd = i2c_get_clientdata(client); > + struct t4ka3_data *sensor = to_t4ka3_sensor(sd); > + > + v4l2_async_unregister_subdev(&sensor->sd); > + media_entity_cleanup(&sensor->sd.entity); > + v4l2_ctrl_handler_free(&sensor->ctrls.handler); > + > + /* > + * Disable runtime PM. In case runtime PM is disabled in the kernel, > + * make sure to turn power off manually. > + */ > + pm_runtime_disable(&client->dev); > + if (!pm_runtime_status_suspended(&client->dev)) > + t4ka3_pm_suspend(&client->dev); > + pm_runtime_set_suspended(&client->dev); > +} > + > +static int t4ka3_probe(struct i2c_client *client) > +{ > + struct t4ka3_data *sensor; > + int ret; > + > + /* allocate sensor device & init sub device */ > + sensor = devm_kzalloc(&client->dev, sizeof(*sensor), GFP_KERNEL); > + if (!sensor) > + return -ENOMEM; > + > + sensor->dev = &client->dev; > + > + ret = t4ka3_check_hwcfg(sensor); > + if (ret) > + return ret; > + > + mutex_init(&sensor->lock); > + > + sensor->link_freq[0] = T4KA3_LINK_FREQ; > + sensor->mode.crop = t4ka3_default_crop; > + t4ka3_fill_format(sensor, &sensor->mode.fmt, T4KA3_ACTIVE_WIDTH, T4KA3_ACTIVE_HEIGHT); > + t4ka3_calc_mode(sensor); > + > + v4l2_i2c_subdev_init(&sensor->sd, client, &t4ka3_ops); > + sensor->sd.internal_ops = &t4ka3_internal_ops; > + > + sensor->powerdown_gpio = devm_gpiod_get(&client->dev, "powerdown", > + GPIOD_OUT_HIGH); > + if (IS_ERR(sensor->powerdown_gpio)) > + return dev_err_probe(&client->dev, PTR_ERR(sensor->powerdown_gpio), > + "getting powerdown GPIO\n"); > + > + sensor->reset_gpio = devm_gpiod_get_optional(&client->dev, "reset", > + GPIOD_OUT_HIGH); > + if (IS_ERR(sensor->reset_gpio)) > + return dev_err_probe(&client->dev, PTR_ERR(sensor->reset_gpio), > + "getting reset GPIO\n"); > + > + sensor->regmap = devm_cci_regmap_init_i2c(client, 16); > + if (IS_ERR(sensor->regmap)) > + return PTR_ERR(sensor->regmap); > + > + ret = t4ka3_pm_resume(sensor->dev); > + if (ret) > + return ret; > + > + pm_runtime_set_active(&client->dev); > + pm_runtime_get_noresume(&client->dev); > + pm_runtime_enable(&client->dev); > + > + sensor->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE; > + sensor->pad.flags = MEDIA_PAD_FL_SOURCE; > + sensor->sd.entity.function = MEDIA_ENT_F_CAM_SENSOR; > + > + ret = t4ka3_init_controls(sensor); > + if (ret) > + goto err_controls; > + > + ret = media_entity_pads_init(&sensor->sd.entity, 1, &sensor->pad); > + if (ret) > + goto err_controls; > + > + ret = v4l2_async_register_subdev_sensor(&sensor->sd); > + if (ret) > + goto err_media_entity; > + > + pm_runtime_set_autosuspend_delay(&client->dev, 1000); > + pm_runtime_use_autosuspend(&client->dev); > + pm_runtime_put_autosuspend(&client->dev); > + > + return 0; > + > +err_media_entity: > + media_entity_cleanup(&sensor->sd.entity); > +err_controls: > + v4l2_ctrl_handler_free(&sensor->ctrls.handler); > + pm_runtime_disable(&client->dev); > + pm_runtime_put_noidle(&client->dev); > + return ret; > +} > + > +static struct acpi_device_id t4ka3_acpi_match[] = { > + { "XMCC0003" }, > + {} > +}; > +MODULE_DEVICE_TABLE(acpi, t4ka3_acpi_match); > + > +static struct i2c_driver t4ka3_driver = { > + .driver = { > + .name = "t4ka3", > + .acpi_match_table = ACPI_PTR(t4ka3_acpi_match), > + .pm = pm_sleep_ptr(&t4ka3_pm_ops), > + }, > + .probe = t4ka3_probe, > + .remove = t4ka3_remove, > +}; > +module_i2c_driver(t4ka3_driver) > + > +MODULE_DESCRIPTION("A low-level driver for T4KA3 sensor"); > +MODULE_AUTHOR("HARVEY LV <harvey.lv@intel.com>"); > +MODULE_LICENSE("GPL");
Hi Hans, On Wed, Nov 6, 2024 at 4:11 AM Hans de Goede <hdegoede@redhat.com> wrote: > > Hi Kate, > > On 29-Oct-24 10:10 AM, Kate Hsuan wrote: > > Add the t4ka3 driver from: > > https://github.com/kitakar5525/surface3-atomisp-cameras.git > > > > With many cleanups / changes (almost a full rewrite) to make it suitable > > for upstream: > > > > * Remove the VCM and VCM-OTP support, the mainline kernel models VCMs and > > calibration data eeproms as separate v4l2-subdev-s. > > > > * Remove the integration-factor t4ka3_get_intg_factor() support and IOCTL, > > this provided info to userspace through an atomisp private IOCTL. > > > > * Turn atomisp specific exposure/gain IOCTL into standard v4l2 controls. > > > > * Use normal ACPI power-management in combination with runtime-pm support > > instead of atomisp specific GMIN power-management code. > > > > * Turn into a standard V4L2 sensor driver using > > v4l2_async_register_subdev_sensor(). > > > > * Add vblank, hblank, and link-freq controls; drop get_frame_interval(). > > > > * Use CCI register helpers. > > > > * Calculate values for modes instead of using fixed register-value lists, > > allowing arbritrary modes. > > > > * Add get_selection() and set_selection() support > > > > * Add a CSI2 bus configuration check > > > > This been tested on a Xiaomi Mipad2 tablet which has a T4KA3 sensor with > > DW9761 VCM as back sensor. > > I tested this with the atomisp libcamera pipeline handler I have > been working on and this is missing the mandatory pixel_rate > control. > > That and it would be nice to also parse the properties indicating > if this is a back or front camera. > > Attached is a patch which adds both, can you do a v7 with these > changes squashed in ? > Thank you for reviewing. Sure no problem, I'll squash it and propose a v7 patch. > Regards, > > Hans > > > > > Co-developed-by: Hans de Goede <hdegoede@redhat.com> > > Signed-off-by: Hans de Goede <hdegoede@redhat.com> > > Signed-off-by: Kate Hsuan <hpa@redhat.com> > > --- > > Changes in v6: > > 1. t4ka3_s_config() was removed. > > 2. The unused macros were removed. > > 3. The runtime pm initial flow was improved. > > 4. In remove(), if the device is not in the "suspend" state, the device > > will be manually turned off. > > > > Changes in v5: > > 1. Improved Kconfig help description. > > > > Changes in v4: > > 1. Another CI issue fixes. > > > > Changes in v3: > > 1. Fix the issues reported by the CI system. > > > > Changes in v2: > > 1. The regmap information was obtained before configuring runtime PM so > > probe() can return without disabling runtime PM. > > 2. In t4ka3_s_stream(), return -EBUSY when the streaming is enabled. > > --- > > drivers/media/i2c/Kconfig | 12 + > > drivers/media/i2c/Makefile | 1 + > > drivers/media/i2c/t4ka3.c | 1099 ++++++++++++++++++++++++++++++++++++ > > 3 files changed, 1112 insertions(+) > > create mode 100644 drivers/media/i2c/t4ka3.c > > > > diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig > > index 8ba096b8ebca..6ec51f969b32 100644 > > --- a/drivers/media/i2c/Kconfig > > +++ b/drivers/media/i2c/Kconfig > > @@ -690,6 +690,18 @@ config VIDEO_S5K6A3 > > This is a V4L2 sensor driver for Samsung S5K6A3 raw > > camera sensor. > > > > +config VIDEO_T4KA3 > > + tristate "Toshiba T4KA3 sensor support" > > + depends on ACPI || COMPILE_TEST > > + depends on GPIOLIB > > + select V4L2_CCI_I2C > > + help > > + This is a Video4Linux2 sensor driver for the Toshiba T4KA3 8 MP > > + camera sensor. > > + > > + To compile this driver as a module, choose M here: the > > + module will be called t4ka3. > > + > > config VIDEO_VGXY61 > > tristate "ST VGXY61 sensor support" > > select V4L2_CCI_I2C > > diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile > > index fbb988bd067a..ad67ea33ce37 100644 > > --- a/drivers/media/i2c/Makefile > > +++ b/drivers/media/i2c/Makefile > > @@ -129,6 +129,7 @@ obj-$(CONFIG_VIDEO_SAA717X) += saa717x.o > > obj-$(CONFIG_VIDEO_SAA7185) += saa7185.o > > obj-$(CONFIG_VIDEO_SONY_BTF_MPX) += sony-btf-mpx.o > > obj-$(CONFIG_VIDEO_ST_MIPID02) += st-mipid02.o > > +obj-$(CONFIG_VIDEO_T4KA3) += t4ka3.o > > obj-$(CONFIG_VIDEO_TC358743) += tc358743.o > > obj-$(CONFIG_VIDEO_TC358746) += tc358746.o > > obj-$(CONFIG_VIDEO_TDA1997X) += tda1997x.o > > diff --git a/drivers/media/i2c/t4ka3.c b/drivers/media/i2c/t4ka3.c > > new file mode 100644 > > index 000000000000..ee4455a5e8e4 > > --- /dev/null > > +++ b/drivers/media/i2c/t4ka3.c > > @@ -0,0 +1,1099 @@ > > +// SPDX-License-Identifier: GPL-2.0 > > +/* > > + * Support for T4KA3 8M camera sensor. > > + * > > + * Copyright (C) 2015 Intel Corporation. All Rights Reserved. > > + * Copyright (C) 2016 XiaoMi, Inc. > > + * Copyright (C) 2024 Hans de Goede <hansg@kernel.org> > > + */ > > + > > +#include <linux/acpi.h> > > +#include <linux/bits.h> > > +#include <linux/delay.h> > > +#include <linux/dev_printk.h> > > +#include <linux/device.h> > > +#include <linux/err.h> > > +#include <linux/errno.h> > > +#include <linux/gpio/consumer.h> > > +#include <linux/i2c.h> > > +#include <linux/mod_devicetable.h> > > +#include <linux/mutex.h> > > +#include <linux/pm_runtime.h> > > +#include <linux/regmap.h> > > +#include <linux/types.h> > > + > > +#include <media/media-entity.h> > > +#include <media/v4l2-async.h> > > +#include <media/v4l2-cci.h> > > +#include <media/v4l2-common.h> > > +#include <media/v4l2-ctrls.h> > > +#include <media/v4l2-fwnode.h> > > +#include <media/v4l2-subdev.h> > > + > > +#define T4KA3_NATIVE_WIDTH 3280 > > +#define T4KA3_NATIVE_HEIGHT 2464 > > +#define T4KA3_NATIVE_START_LEFT 0 > > +#define T4KA3_NATIVE_START_TOP 0 > > +#define T4KA3_ACTIVE_WIDTH 3280 > > +#define T4KA3_ACTIVE_HEIGHT 2460 > > +#define T4KA3_ACTIVE_START_LEFT 0 > > +#define T4KA3_ACTIVE_START_TOP 2 > > +#define T4KA3_MIN_CROP_WIDTH 2 > > +#define T4KA3_MIN_CROP_HEIGHT 2 > > + > > +#define T4KA3_PIXELS_PER_LINE 3440 > > +#define T4KA3_LINES_PER_FRAME_30FPS 2492 > > +#define T4KA3_FPS 30 > > +#define T4KA3_PIXEL_RATE \ > > + (T4KA3_PIXELS_PER_LINE * T4KA3_LINES_PER_FRAME_30FPS * T4KA3_FPS) > > + > > +/* > > + * TODO this really should be derived from the 19.2 MHz xvclk combined > > + * with the PLL settings. But without a datasheet this is the closest > > + * approximation possible. > > + * > > + * link-freq = pixel_rate * bpp / (lanes * 2) > > + * (lanes * 2) because CSI lanes use double-data-rate (DDR) signalling. > > + * bpp = 10 and lanes = 4 > > + */ > > +#define T4KA3_LINK_FREQ ((u64)T4KA3_PIXEL_RATE * 10 / 8) > > + > > +/* For enum_frame_size() full-size + binned-/quarter-size */ > > +#define T4KA3_FRAME_SIZES 2 > > + > > +#define T4KA3_REG_PRODUCT_ID_HIGH CCI_REG8(0x0000) > > +#define T4KA3_REG_PRODUCT_ID_LOW CCI_REG8(0x0001) > > +#define T4KA3_PRODUCT_ID 0x1490 > > + > > +#define T4KA3_REG_STREAM CCI_REG8(0x0100) > > +#define T4KA3_REG_IMG_ORIENTATION CCI_REG8(0x0101) > > +#define T4KA3_HFLIP_BIT BIT(0) > > +#define T4KA3_VFLIP_BIT BIT(1) > > +#define T4KA3_REG_PARAM_HOLD CCI_REG8(0x0104) > > +#define T4KA3_REG_COARSE_INTEGRATION_TIME CCI_REG16(0x0202) > > +#define T4KA3_COARSE_INTEGRATION_TIME_MARGIN 6 > > +#define T4KA3_REG_DIGGAIN_GREEN_R CCI_REG16(0x020e) > > +#define T4KA3_REG_DIGGAIN_RED CCI_REG16(0x0210) > > +#define T4KA3_REG_DIGGAIN_BLUE CCI_REG16(0x0212) > > +#define T4KA3_REG_DIGGAIN_GREEN_B CCI_REG16(0x0214) > > +#define T4KA3_REG_GLOBAL_GAIN CCI_REG16(0x0234) > > +#define T4KA3_MIN_GLOBAL_GAIN_SUPPORTED 0x0080 > > +#define T4KA3_MAX_GLOBAL_GAIN_SUPPORTED 0x07ff > > +#define T4KA3_REG_FRAME_LENGTH_LINES CCI_REG16(0x0340) /* aka VTS */ > > +/* FIXME: need a datasheet to verify the min + max vblank values */ > > +#define T4KA3_MIN_VBLANK 4 > > +#define T4KA3_MAX_VBLANK 0xffff > > +#define T4KA3_REG_PIXELS_PER_LINE CCI_REG16(0x0342) /* aka HTS */ > > +/* These 2 being horz/vert start is a guess (no datasheet), always 0 */ > > +#define T4KA3_REG_HORZ_START CCI_REG16(0x0344) > > +#define T4KA3_REG_VERT_START CCI_REG16(0x0346) > > +/* Always 3279 (T4KA3_NATIVE_WIDTH - 1, window is used to crop */ > > +#define T4KA3_REG_HORZ_END CCI_REG16(0x0348) > > +/* Always 2463 (T4KA3_NATIVE_HEIGHT - 1, window is used to crop */ > > +#define T4KA3_REG_VERT_END CCI_REG16(0x034a) > > +/* Output size (after cropping/window) */ > > +#define T4KA3_REG_HORZ_OUTPUT_SIZE CCI_REG16(0x034c) > > +#define T4KA3_REG_VERT_OUTPUT_SIZE CCI_REG16(0x034e) > > +/* Window/crop start + size *after* binning */ > > +#define T4KA3_REG_WIN_START_X CCI_REG16(0x0408) > > +#define T4KA3_REG_WIN_START_Y CCI_REG16(0x040a) > > +#define T4KA3_REG_WIN_WIDTH CCI_REG16(0x040c) > > +#define T4KA3_REG_WIN_HEIGHT CCI_REG16(0x040e) > > +#define T4KA3_REG_TEST_PATTERN_MODE CCI_REG8(0x0601) > > +/* Unknown register at address 0x0900 */ > > +#define T4KA3_REG_0900 CCI_REG8(0x0900) > > +#define T4KA3_REG_BINNING CCI_REG8(0x0901) > > +#define T4KA3_BINNING_VAL(_b) \ > > + ({ typeof(_b) (b) = (_b); \ > > + ((b) << 4) | (b); }) > > + > > +struct t4ka3_ctrls { > > + struct v4l2_ctrl_handler handler; > > + struct v4l2_ctrl *hflip; > > + struct v4l2_ctrl *vflip; > > + struct v4l2_ctrl *vblank; > > + struct v4l2_ctrl *hblank; > > + struct v4l2_ctrl *exposure; > > + struct v4l2_ctrl *test_pattern; > > + struct v4l2_ctrl *link_freq; > > + struct v4l2_ctrl *gain; > > +}; > > + > > +struct t4ka3_mode { > > + struct v4l2_rect crop; > > + struct v4l2_mbus_framefmt fmt; > > + int binning; > > + u16 win_x; > > + u16 win_y; > > +}; > > + > > +struct t4ka3_data { > > + struct v4l2_subdev sd; > > + struct media_pad pad; > > + struct mutex lock; /* serialize sensor's ioctl */ > > + struct t4ka3_ctrls ctrls; > > + struct t4ka3_mode mode; > > + struct device *dev; > > + struct regmap *regmap; > > + struct gpio_desc *powerdown_gpio; > > + struct gpio_desc *reset_gpio; > > + s64 link_freq[1]; > > + int streaming; > > +}; > > + > > +/* init settings */ > > +static const struct cci_reg_sequence t4ka3_init_config[] = { > > + {CCI_REG8(0x4136), 0x13}, > > + {CCI_REG8(0x4137), 0x33}, > > + {CCI_REG8(0x3094), 0x01}, > > + {CCI_REG8(0x0233), 0x01}, > > + {CCI_REG8(0x4B06), 0x01}, > > + {CCI_REG8(0x4B07), 0x01}, > > + {CCI_REG8(0x3028), 0x01}, > > + {CCI_REG8(0x3032), 0x14}, > > + {CCI_REG8(0x305C), 0x0C}, > > + {CCI_REG8(0x306D), 0x0A}, > > + {CCI_REG8(0x3071), 0xFA}, > > + {CCI_REG8(0x307E), 0x0A}, > > + {CCI_REG8(0x307F), 0xFC}, > > + {CCI_REG8(0x3091), 0x04}, > > + {CCI_REG8(0x3092), 0x60}, > > + {CCI_REG8(0x3096), 0xC0}, > > + {CCI_REG8(0x3100), 0x07}, > > + {CCI_REG8(0x3101), 0x4C}, > > + {CCI_REG8(0x3118), 0xCC}, > > + {CCI_REG8(0x3139), 0x06}, > > + {CCI_REG8(0x313A), 0x06}, > > + {CCI_REG8(0x313B), 0x04}, > > + {CCI_REG8(0x3143), 0x02}, > > + {CCI_REG8(0x314F), 0x0E}, > > + {CCI_REG8(0x3169), 0x99}, > > + {CCI_REG8(0x316A), 0x99}, > > + {CCI_REG8(0x3171), 0x05}, > > + {CCI_REG8(0x31A1), 0xA7}, > > + {CCI_REG8(0x31A2), 0x9C}, > > + {CCI_REG8(0x31A3), 0x8F}, > > + {CCI_REG8(0x31A4), 0x75}, > > + {CCI_REG8(0x31A5), 0xEE}, > > + {CCI_REG8(0x31A6), 0xEA}, > > + {CCI_REG8(0x31A7), 0xE4}, > > + {CCI_REG8(0x31A8), 0xE4}, > > + {CCI_REG8(0x31DF), 0x05}, > > + {CCI_REG8(0x31EC), 0x1B}, > > + {CCI_REG8(0x31ED), 0x1B}, > > + {CCI_REG8(0x31EE), 0x1B}, > > + {CCI_REG8(0x31F0), 0x1B}, > > + {CCI_REG8(0x31F1), 0x1B}, > > + {CCI_REG8(0x31F2), 0x1B}, > > + {CCI_REG8(0x3204), 0x3F}, > > + {CCI_REG8(0x3205), 0x03}, > > + {CCI_REG8(0x3210), 0x01}, > > + {CCI_REG8(0x3216), 0x68}, > > + {CCI_REG8(0x3217), 0x58}, > > + {CCI_REG8(0x3218), 0x58}, > > + {CCI_REG8(0x321A), 0x68}, > > + {CCI_REG8(0x321B), 0x60}, > > + {CCI_REG8(0x3238), 0x03}, > > + {CCI_REG8(0x3239), 0x03}, > > + {CCI_REG8(0x323A), 0x05}, > > + {CCI_REG8(0x323B), 0x06}, > > + {CCI_REG8(0x3243), 0x03}, > > + {CCI_REG8(0x3244), 0x08}, > > + {CCI_REG8(0x3245), 0x01}, > > + {CCI_REG8(0x3307), 0x19}, > > + {CCI_REG8(0x3308), 0x19}, > > + {CCI_REG8(0x3320), 0x01}, > > + {CCI_REG8(0x3326), 0x15}, > > + {CCI_REG8(0x3327), 0x0D}, > > + {CCI_REG8(0x3328), 0x01}, > > + {CCI_REG8(0x3380), 0x01}, > > + {CCI_REG8(0x339E), 0x07}, > > + {CCI_REG8(0x3424), 0x00}, > > + {CCI_REG8(0x343C), 0x01}, > > + {CCI_REG8(0x3398), 0x04}, > > + {CCI_REG8(0x343A), 0x10}, > > + {CCI_REG8(0x339A), 0x22}, > > + {CCI_REG8(0x33B4), 0x00}, > > + {CCI_REG8(0x3393), 0x01}, > > + {CCI_REG8(0x33B3), 0x6E}, > > + {CCI_REG8(0x3433), 0x06}, > > + {CCI_REG8(0x3433), 0x00}, > > + {CCI_REG8(0x33B3), 0x00}, > > + {CCI_REG8(0x3393), 0x03}, > > + {CCI_REG8(0x33B4), 0x03}, > > + {CCI_REG8(0x343A), 0x00}, > > + {CCI_REG8(0x339A), 0x00}, > > + {CCI_REG8(0x3398), 0x00} > > +}; > > + > > +static const struct cci_reg_sequence t4ka3_pre_mode_set_regs[] = { > > + {CCI_REG8(0x0112), 0x0A}, > > + {CCI_REG8(0x0113), 0x0A}, > > + {CCI_REG8(0x0114), 0x03}, > > + {CCI_REG8(0x4136), 0x13}, > > + {CCI_REG8(0x4137), 0x33}, > > + {CCI_REG8(0x0820), 0x0A}, > > + {CCI_REG8(0x0821), 0x0D}, > > + {CCI_REG8(0x0822), 0x00}, > > + {CCI_REG8(0x0823), 0x00}, > > + {CCI_REG8(0x0301), 0x0A}, > > + {CCI_REG8(0x0303), 0x01}, > > + {CCI_REG8(0x0305), 0x04}, > > + {CCI_REG8(0x0306), 0x02}, > > + {CCI_REG8(0x0307), 0x18}, > > + {CCI_REG8(0x030B), 0x01}, > > +}; > > + > > +static const struct cci_reg_sequence t4ka3_post_mode_set_regs[] = { > > + {CCI_REG8(0x0902), 0x00}, > > + {CCI_REG8(0x4220), 0x00}, > > + {CCI_REG8(0x4222), 0x01}, > > + {CCI_REG8(0x3380), 0x01}, > > + {CCI_REG8(0x3090), 0x88}, > > + {CCI_REG8(0x3394), 0x20}, > > + {CCI_REG8(0x3090), 0x08}, > > + {CCI_REG8(0x3394), 0x10} > > +}; > > + > > +static inline struct t4ka3_data *to_t4ka3_sensor(struct v4l2_subdev *sd) > > +{ > > + return container_of(sd, struct t4ka3_data, sd); > > +} > > + > > +static inline struct t4ka3_data *ctrl_to_t4ka3(struct v4l2_ctrl *ctrl) > > +{ > > + return container_of(ctrl->handler, struct t4ka3_data, ctrls.handler); > > +} > > + > > +/* T4KA3 default GRBG */ > > +static const int t4ka3_hv_flip_bayer_order[] = { > > + MEDIA_BUS_FMT_SGRBG10_1X10, > > + MEDIA_BUS_FMT_SBGGR10_1X10, > > + MEDIA_BUS_FMT_SRGGB10_1X10, > > + MEDIA_BUS_FMT_SGBRG10_1X10, > > +}; > > + > > +static const struct v4l2_rect t4ka3_default_crop = { > > + .left = T4KA3_ACTIVE_START_LEFT, > > + .top = T4KA3_ACTIVE_START_TOP, > > + .width = T4KA3_ACTIVE_WIDTH, > > + .height = T4KA3_ACTIVE_HEIGHT, > > +}; > > + > > +static int t4ka3_detect(struct t4ka3_data *sensor, u16 *id); > > + > > +static void t4ka3_set_bayer_order(struct t4ka3_data *sensor, > > + struct v4l2_mbus_framefmt *fmt) > > +{ > > + int hv_flip = 0; > > + > > + if (sensor->ctrls.vflip && sensor->ctrls.vflip->val) > > + hv_flip += 1; > > + > > + if (sensor->ctrls.hflip && sensor->ctrls.hflip->val) > > + hv_flip += 2; > > + > > + fmt->code = t4ka3_hv_flip_bayer_order[hv_flip]; > > +} > > + > > +static int t4ka3_update_exposure_range(struct t4ka3_data *sensor) > > +{ > > + int exp_max = sensor->mode.fmt.height + sensor->ctrls.vblank->val - > > + T4KA3_COARSE_INTEGRATION_TIME_MARGIN; > > + > > + return __v4l2_ctrl_modify_range(sensor->ctrls.exposure, 0, exp_max, > > + 1, exp_max); > > +} > > + > > +static struct v4l2_rect * > > +__t4ka3_get_pad_crop(struct t4ka3_data *sensor, > > + struct v4l2_subdev_state *state, > > + unsigned int pad, > > + enum v4l2_subdev_format_whence which) > > +{ > > + if (which == V4L2_SUBDEV_FORMAT_TRY) > > + return v4l2_subdev_state_get_crop(state, pad); > > + > > + return &sensor->mode.crop; > > +} > > + > > +static struct v4l2_mbus_framefmt * > > +__t4ka3_get_pad_format(struct t4ka3_data *sensor, > > + struct v4l2_subdev_state *sd_state, unsigned int pad, > > + enum v4l2_subdev_format_whence which) > > +{ > > + if (which == V4L2_SUBDEV_FORMAT_TRY) > > + return v4l2_subdev_state_get_format(sd_state, pad); > > + > > + return &sensor->mode.fmt; > > +} > > + > > +static void t4ka3_fill_format(struct t4ka3_data *sensor, > > + struct v4l2_mbus_framefmt *fmt, > > + unsigned int width, unsigned int height) > > +{ > > + memset(fmt, 0, sizeof(*fmt)); > > + fmt->width = width; > > + fmt->height = height; > > + fmt->field = V4L2_FIELD_NONE; > > + fmt->colorspace = V4L2_COLORSPACE_SRGB; > > + t4ka3_set_bayer_order(sensor, fmt); > > +} > > + > > +static void t4ka3_calc_mode(struct t4ka3_data *sensor) > > +{ > > + int width = sensor->mode.fmt.width; > > + int height = sensor->mode.fmt.height; > > + int binning; > > + > > + if (width <= (sensor->mode.crop.width / 2) && > > + height <= (sensor->mode.crop.height / 2)) > > + binning = 2; > > + else > > + binning = 1; > > + > > + width *= binning; > > + height *= binning; > > + > > + sensor->mode.binning = binning; > > + sensor->mode.win_x = (sensor->mode.crop.left + > > + (sensor->mode.crop.width - width) / 2) & ~1; > > + sensor->mode.win_y = (sensor->mode.crop.top + > > + (sensor->mode.crop.height - height) / 2) & ~1; > > + /* > > + * t4ka's window is done after binning, but must still be a multiple of 2 ? > > + * Round up to avoid top 2 black lines in 1640x1230 (quarter res) case. > > + */ > > + sensor->mode.win_x = DIV_ROUND_UP(sensor->mode.win_x, binning); > > + sensor->mode.win_y = DIV_ROUND_UP(sensor->mode.win_y, binning); > > +} > > + > > +static void t4ka3_get_vblank_limits(struct t4ka3_data *sensor, int *min, int *max, int *def) > > +{ > > + *min = T4KA3_MIN_VBLANK + (sensor->mode.binning - 1) * sensor->mode.fmt.height; > > + *max = T4KA3_MAX_VBLANK - sensor->mode.fmt.height; > > + *def = T4KA3_LINES_PER_FRAME_30FPS - sensor->mode.fmt.height; > > +} > > + > > +static int t4ka3_set_pad_format(struct v4l2_subdev *sd, > > + struct v4l2_subdev_state *sd_state, > > + struct v4l2_subdev_format *format) > > +{ > > + struct t4ka3_data *sensor = to_t4ka3_sensor(sd); > > + struct v4l2_mbus_framefmt *try_fmt; > > + const struct v4l2_rect *crop; > > + unsigned int width, height; > > + int min, max, def, ret = 0; > > + > > + crop = __t4ka3_get_pad_crop(sensor, sd_state, format->pad, format->which); > > + > > + /* Limit set_fmt max size to crop width / height */ > > + width = clamp_val(ALIGN(format->format.width, 2), > > + T4KA3_MIN_CROP_WIDTH, crop->width); > > + height = clamp_val(ALIGN(format->format.height, 2), > > + T4KA3_MIN_CROP_HEIGHT, crop->height); > > + t4ka3_fill_format(sensor, &format->format, width, height); > > + > > + if (format->which == V4L2_SUBDEV_FORMAT_TRY) { > > + try_fmt = v4l2_subdev_state_get_format(sd_state, 0); > > + *try_fmt = format->format; > > + return 0; > > + } > > + > > + mutex_lock(&sensor->lock); > > + > > + if (sensor->streaming) { > > + ret = -EBUSY; > > + goto unlock; > > + } > > + > > + sensor->mode.fmt = format->format; > > + t4ka3_calc_mode(sensor); > > + > > + /* vblank range is height dependent adjust and reset to default */ > > + t4ka3_get_vblank_limits(sensor, &min, &max, &def); > > + ret = __v4l2_ctrl_modify_range(sensor->ctrls.vblank, min, max, 1, def); > > + if (ret) > > + goto unlock; > > + > > + ret = __v4l2_ctrl_s_ctrl(sensor->ctrls.vblank, def); > > + if (ret) > > + goto unlock; > > + > > + def = T4KA3_ACTIVE_WIDTH - sensor->mode.fmt.width; > > + ret = __v4l2_ctrl_modify_range(sensor->ctrls.hblank, def, def, 1, def); > > + if (ret) > > + goto unlock; > > + ret = __v4l2_ctrl_s_ctrl(sensor->ctrls.hblank, def); > > + if (ret) > > + goto unlock; > > + > > + /* exposure range depends on vts which may have changed */ > > + ret = t4ka3_update_exposure_range(sensor); > > + if (ret) > > + goto unlock; > > + > > +unlock: > > + mutex_unlock(&sensor->lock); > > + return ret; > > +} > > + > > +/* Horizontal flip the image. */ > > +static int t4ka3_t_hflip(struct v4l2_subdev *sd, int value) > > +{ > > + struct t4ka3_data *sensor = to_t4ka3_sensor(sd); > > + int ret; > > + u64 val; > > + > > + if (sensor->streaming) > > + return -EBUSY; > > + > > + val = value ? T4KA3_HFLIP_BIT : 0; > > + > > + ret = cci_update_bits(sensor->regmap, T4KA3_REG_IMG_ORIENTATION, > > + T4KA3_HFLIP_BIT, val, NULL); > > + if (ret) > > + return ret; > > + > > + t4ka3_set_bayer_order(sensor, &sensor->mode.fmt); > > + return 0; > > +} > > + > > +/* Vertically flip the image */ > > +static int t4ka3_t_vflip(struct v4l2_subdev *sd, int value) > > +{ > > + struct t4ka3_data *sensor = to_t4ka3_sensor(sd); > > + int ret; > > + u64 val; > > + > > + if (sensor->streaming) > > + return -EBUSY; > > + > > + val = value ? T4KA3_VFLIP_BIT : 0; > > + > > + ret = cci_update_bits(sensor->regmap, T4KA3_REG_IMG_ORIENTATION, > > + T4KA3_VFLIP_BIT, val, NULL); > > + if (ret) > > + return ret; > > + > > + t4ka3_set_bayer_order(sensor, &sensor->mode.fmt); > > + return 0; > > +} > > + > > +static int t4ka3_test_pattern(struct t4ka3_data *sensor, s32 value) > > +{ > > + return cci_write(sensor->regmap, T4KA3_REG_TEST_PATTERN_MODE, value, NULL); > > +} > > + > > +static int t4ka3_detect(struct t4ka3_data *sensor, u16 *id) > > +{ > > + struct i2c_client *client = v4l2_get_subdevdata(&sensor->sd); > > + struct i2c_adapter *adapter = client->adapter; > > + u64 high, low; > > + int ret = 0; > > + > > + /* i2c check */ > > + if (!i2c_check_functionality(adapter, I2C_FUNC_I2C)) > > + return -ENODEV; > > + > > + /* check sensor chip ID */ > > + cci_read(sensor->regmap, T4KA3_REG_PRODUCT_ID_HIGH, &high, &ret); > > + cci_read(sensor->regmap, T4KA3_REG_PRODUCT_ID_LOW, &low, &ret); > > + if (ret) > > + return ret; > > + > > + *id = (((u8)high) << 8) | (u8)low; > > + if (*id != T4KA3_PRODUCT_ID) { > > + dev_err(sensor->dev, "main sensor t4ka3 ID error\n"); > > + return -ENODEV; > > + } > > + > > + return 0; > > +} > > + > > +static int t4ka3_s_ctrl(struct v4l2_ctrl *ctrl) > > +{ > > + struct t4ka3_data *sensor = ctrl_to_t4ka3(ctrl); > > + int ret; > > + > > + /* Update exposure range on vblank changes */ > > + if (ctrl->id == V4L2_CID_VBLANK) { > > + ret = t4ka3_update_exposure_range(sensor); > > + if (ret) > > + return ret; > > + } > > + > > + /* Only apply changes to the controls if the device is powered up */ > > + if (!pm_runtime_get_if_in_use(sensor->sd.dev)) { > > + t4ka3_set_bayer_order(sensor, &sensor->mode.fmt); > > + return 0; > > + } > > + > > + switch (ctrl->id) { > > + case V4L2_CID_TEST_PATTERN: > > + ret = t4ka3_test_pattern(sensor, ctrl->val); > > + break; > > + case V4L2_CID_VFLIP: > > + ret = t4ka3_t_vflip(&sensor->sd, ctrl->val); > > + break; > > + case V4L2_CID_HFLIP: > > + ret = t4ka3_t_hflip(&sensor->sd, ctrl->val); > > + break; > > + case V4L2_CID_VBLANK: > > + ret = cci_write(sensor->regmap, T4KA3_REG_FRAME_LENGTH_LINES, > > + sensor->mode.fmt.height + ctrl->val, NULL); > > + break; > > + case V4L2_CID_EXPOSURE: > > + ret = cci_write(sensor->regmap, T4KA3_REG_COARSE_INTEGRATION_TIME, > > + ctrl->val, NULL); > > + break; > > + case V4L2_CID_ANALOGUE_GAIN: > > + ret = cci_write(sensor->regmap, T4KA3_REG_GLOBAL_GAIN, > > + ctrl->val, NULL); > > + break; > > + default: > > + ret = -EINVAL; > > + break; > > + } > > + > > + pm_runtime_put(sensor->sd.dev); > > + return ret; > > +} > > + > > +static int t4ka3_set_mode(struct t4ka3_data *sensor) > > +{ > > + int ret = 0; > > + > > + cci_write(sensor->regmap, T4KA3_REG_HORZ_OUTPUT_SIZE, sensor->mode.fmt.width, &ret); > > + /* Write mode-height - 2 otherwise things don't work, hw-bug ? */ > > + cci_write(sensor->regmap, T4KA3_REG_VERT_OUTPUT_SIZE, sensor->mode.fmt.height - 2, &ret); > > + /* Note overwritten by __v4l2_ctrl_handler_setup() based on vblank ctrl */ > > + cci_write(sensor->regmap, T4KA3_REG_FRAME_LENGTH_LINES, T4KA3_LINES_PER_FRAME_30FPS, &ret); > > + cci_write(sensor->regmap, T4KA3_REG_PIXELS_PER_LINE, T4KA3_PIXELS_PER_LINE, &ret); > > + /* Always use the full sensor, using window to crop */ > > + cci_write(sensor->regmap, T4KA3_REG_HORZ_START, 0, &ret); > > + cci_write(sensor->regmap, T4KA3_REG_VERT_START, 0, &ret); > > + cci_write(sensor->regmap, T4KA3_REG_HORZ_END, T4KA3_NATIVE_WIDTH - 1, &ret); > > + cci_write(sensor->regmap, T4KA3_REG_VERT_END, T4KA3_NATIVE_HEIGHT - 1, &ret); > > + /* Set window */ > > + cci_write(sensor->regmap, T4KA3_REG_WIN_START_X, sensor->mode.win_x, &ret); > > + cci_write(sensor->regmap, T4KA3_REG_WIN_START_Y, sensor->mode.win_y, &ret); > > + cci_write(sensor->regmap, T4KA3_REG_WIN_WIDTH, sensor->mode.fmt.width, &ret); > > + cci_write(sensor->regmap, T4KA3_REG_WIN_HEIGHT, sensor->mode.fmt.height, &ret); > > + /* Write 1 to unknown register 0x0900 */ > > + cci_write(sensor->regmap, T4KA3_REG_0900, 1, &ret); > > + cci_write(sensor->regmap, T4KA3_REG_BINNING, T4KA3_BINNING_VAL(sensor->mode.binning), &ret); > > + > > + return ret; > > +} > > + > > +static int t4ka3_s_stream(struct v4l2_subdev *sd, int enable) > > +{ > > + struct t4ka3_data *sensor = to_t4ka3_sensor(sd); > > + int ret; > > + > > + mutex_lock(&sensor->lock); > > + > > + if (sensor->streaming == enable) { > > + dev_warn(sensor->dev, "Stream already %s\n", enable ? "started" : "stopped"); > > + ret = -EBUSY; > > + goto error_unlock; > > + } > > + > > + if (enable) { > > + ret = pm_runtime_get_sync(sensor->sd.dev); > > + if (ret < 0) { > > + dev_err(sensor->dev, "power-up err.\n"); > > + goto error_unlock; > > + } > > + > > + cci_multi_reg_write(sensor->regmap, t4ka3_init_config, > > + ARRAY_SIZE(t4ka3_init_config), &ret); > > + /* enable group hold */ > > + cci_write(sensor->regmap, T4KA3_REG_PARAM_HOLD, 1, &ret); > > + cci_multi_reg_write(sensor->regmap, t4ka3_pre_mode_set_regs, > > + ARRAY_SIZE(t4ka3_pre_mode_set_regs), &ret); > > + if (ret) > > + goto error_powerdown; > > + > > + ret = t4ka3_set_mode(sensor); > > + if (ret) > > + goto error_powerdown; > > + > > + ret = cci_multi_reg_write(sensor->regmap, t4ka3_post_mode_set_regs, > > + ARRAY_SIZE(t4ka3_post_mode_set_regs), NULL); > > + if (ret) > > + goto error_powerdown; > > + > > + /* Restore value of all ctrls */ > > + ret = __v4l2_ctrl_handler_setup(&sensor->ctrls.handler); > > + if (ret) > > + goto error_powerdown; > > + > > + /* disable group hold */ > > + cci_write(sensor->regmap, T4KA3_REG_PARAM_HOLD, 0, &ret); > > + cci_write(sensor->regmap, T4KA3_REG_STREAM, 1, &ret); > > + if (ret) > > + goto error_powerdown; > > + > > + sensor->streaming = 1; > > + } else { > > + ret = cci_write(sensor->regmap, T4KA3_REG_STREAM, 0, NULL); > > + if (ret) > > + goto error_powerdown; > > + > > + ret = pm_runtime_put(sensor->sd.dev); > > + if (ret) > > + goto error_unlock; > > + > > + sensor->streaming = 0; > > + } > > + > > + mutex_unlock(&sensor->lock); > > + return ret; > > + > > +error_powerdown: > > + pm_runtime_put(sensor->sd.dev); > > +error_unlock: > > + mutex_unlock(&sensor->lock); > > + return ret; > > +} > > + > > +static int t4ka3_get_selection(struct v4l2_subdev *sd, > > + struct v4l2_subdev_state *state, > > + struct v4l2_subdev_selection *sel) > > +{ > > + struct t4ka3_data *sensor = to_t4ka3_sensor(sd); > > + > > + switch (sel->target) { > > + case V4L2_SEL_TGT_CROP: > > + mutex_lock(&sensor->lock); > > + sel->r = *__t4ka3_get_pad_crop(sensor, state, sel->pad, > > + sel->which); > > + mutex_unlock(&sensor->lock); > > + break; > > + case V4L2_SEL_TGT_NATIVE_SIZE: > > + case V4L2_SEL_TGT_CROP_BOUNDS: > > + sel->r.top = 0; > > + sel->r.left = 0; > > + sel->r.width = T4KA3_NATIVE_WIDTH; > > + sel->r.height = T4KA3_NATIVE_HEIGHT; > > + break; > > + case V4L2_SEL_TGT_CROP_DEFAULT: > > + sel->r = t4ka3_default_crop; > > + break; > > + default: > > + return -EINVAL; > > + } > > + > > + return 0; > > +} > > + > > +static int t4ka3_set_selection(struct v4l2_subdev *sd, > > + struct v4l2_subdev_state *state, > > + struct v4l2_subdev_selection *sel) > > +{ > > + struct t4ka3_data *sensor = to_t4ka3_sensor(sd); > > + struct v4l2_mbus_framefmt *format; > > + struct v4l2_rect *crop; > > + struct v4l2_rect rect; > > + > > + if (sel->target != V4L2_SEL_TGT_CROP) > > + return -EINVAL; > > + > > + /* > > + * Clamp the boundaries of the crop rectangle to the size of the sensor > > + * pixel array. Align to multiples of 2 to ensure Bayer pattern isn't > > + * disrupted. > > + */ > > + rect.left = clamp_val(ALIGN(sel->r.left, 2), > > + T4KA3_NATIVE_START_LEFT, T4KA3_NATIVE_WIDTH); > > + rect.top = clamp_val(ALIGN(sel->r.top, 2), > > + T4KA3_NATIVE_START_TOP, T4KA3_NATIVE_HEIGHT); > > + rect.width = clamp_val(ALIGN(sel->r.width, 2), > > + T4KA3_MIN_CROP_WIDTH, T4KA3_NATIVE_WIDTH); > > + rect.height = clamp_val(ALIGN(sel->r.height, 2), > > + T4KA3_MIN_CROP_HEIGHT, T4KA3_NATIVE_HEIGHT); > > + > > + /* Make sure the crop rectangle isn't outside the bounds of the array */ > > + rect.width = min_t(unsigned int, rect.width, > > + T4KA3_NATIVE_WIDTH - rect.left); > > + rect.height = min_t(unsigned int, rect.height, > > + T4KA3_NATIVE_HEIGHT - rect.top); > > + > > + crop = __t4ka3_get_pad_crop(sensor, state, sel->pad, sel->which); > > + > > + mutex_lock(&sensor->lock); > > + > > + *crop = rect; > > + > > + if (rect.width != crop->width || rect.height != crop->height) { > > + /* > > + * Reset the output image size if the crop rectangle size has > > + * been modified. > > + */ > > + format = __t4ka3_get_pad_format(sensor, state, sel->pad, > > + sel->which); > > + format->width = rect.width; > > + format->height = rect.height; > > + if (sel->which == V4L2_SUBDEV_FORMAT_ACTIVE) > > + t4ka3_calc_mode(sensor); > > + } > > + > > + mutex_unlock(&sensor->lock); > > + > > + sel->r = rect; > > + > > + return 0; > > +} > > + > > +static int > > +t4ka3_enum_mbus_code(struct v4l2_subdev *sd, > > + struct v4l2_subdev_state *sd_state, > > + struct v4l2_subdev_mbus_code_enum *code) > > +{ > > + if (code->index) > > + return -EINVAL; > > + > > + code->code = MEDIA_BUS_FMT_SGRBG10_1X10; > > + return 0; > > +} > > + > > +static int t4ka3_enum_frame_size(struct v4l2_subdev *sd, > > + struct v4l2_subdev_state *sd_state, > > + struct v4l2_subdev_frame_size_enum *fse) > > +{ > > + struct t4ka3_data *sensor = to_t4ka3_sensor(sd); > > + struct v4l2_rect *crop; > > + > > + if (fse->index >= T4KA3_FRAME_SIZES) > > + return -EINVAL; > > + > > + crop = __t4ka3_get_pad_crop(sensor, sd_state, fse->pad, fse->which); > > + if (!crop) > > + return -EINVAL; > > + > > + fse->min_width = crop->width / (fse->index + 1); > > + fse->min_height = crop->height / (fse->index + 1); > > + fse->max_width = fse->min_width; > > + fse->max_height = fse->min_height; > > + > > + return 0; > > +} > > + > > +static int > > +t4ka3_get_pad_format(struct v4l2_subdev *sd, > > + struct v4l2_subdev_state *sd_state, > > + struct v4l2_subdev_format *fmt) > > +{ > > + struct t4ka3_data *sensor = to_t4ka3_sensor(sd); > > + struct v4l2_mbus_framefmt *format = > > + __t4ka3_get_pad_format(sensor, sd_state, fmt->pad, fmt->which); > > + > > + fmt->format = *format; > > + return 0; > > +} > > + > > +static int t4ka3_check_hwcfg(struct t4ka3_data *sensor) > > +{ > > + struct fwnode_handle *fwnode = dev_fwnode(sensor->dev); > > + struct v4l2_fwnode_endpoint bus_cfg = { > > + .bus_type = V4L2_MBUS_CSI2_DPHY, > > + }; > > + struct fwnode_handle *endpoint; > > + unsigned int i; > > + int ret; > > + > > + /* > > + * Sometimes the fwnode graph is initialized by the bridge driver. > > + * Bridge drivers doing this may also add GPIO mappings, wait for this. > > + */ > > + endpoint = fwnode_graph_get_next_endpoint(fwnode, NULL); > > + if (!endpoint) > > + return dev_err_probe(sensor->dev, -EPROBE_DEFER, > > + "waiting for fwnode graph endpoint\n"); > > + > > + ret = v4l2_fwnode_endpoint_alloc_parse(endpoint, &bus_cfg); > > + fwnode_handle_put(endpoint); > > + if (ret) > > + return ret; > > + > > + if (bus_cfg.bus.mipi_csi2.num_data_lanes != 4) { > > + dev_err(sensor->dev, "only a 4-lane CSI2 config is supported"); > > + ret = -EINVAL; > > + goto out_free_bus_cfg; > > + } > > + > > + if (!bus_cfg.nr_of_link_frequencies) { > > + dev_err(sensor->dev, "no link frequencies defined\n"); > > + ret = -EINVAL; > > + goto out_free_bus_cfg; > > + } > > + > > + for (i = 0; i < bus_cfg.nr_of_link_frequencies; i++) { > > + if (bus_cfg.link_frequencies[i] == T4KA3_LINK_FREQ) > > + break; > > + } > > + > > + if (i == bus_cfg.nr_of_link_frequencies) { > > + dev_err(sensor->dev, "supported link freq %llu not found\n", > > + T4KA3_LINK_FREQ); > > + ret = -EINVAL; > > + goto out_free_bus_cfg; > > + } > > + > > +out_free_bus_cfg: > > + v4l2_fwnode_endpoint_free(&bus_cfg); > > + > > + return ret; > > +} > > + > > +static int t4ka3_init_state(struct v4l2_subdev *sd, > > + struct v4l2_subdev_state *sd_state) > > +{ > > + struct t4ka3_data *sensor = to_t4ka3_sensor(sd); > > + > > + *v4l2_subdev_state_get_crop(sd_state, 0) = t4ka3_default_crop; > > + > > + t4ka3_fill_format(sensor, v4l2_subdev_state_get_format(sd_state, 0), > > + T4KA3_ACTIVE_WIDTH, T4KA3_ACTIVE_HEIGHT); > > + return 0; > > +} > > + > > +static const struct v4l2_ctrl_ops t4ka3_ctrl_ops = { > > + .s_ctrl = t4ka3_s_ctrl, > > +}; > > + > > +static const struct v4l2_subdev_video_ops t4ka3_video_ops = { > > + .s_stream = t4ka3_s_stream, > > +}; > > + > > +static const struct v4l2_subdev_pad_ops t4ka3_pad_ops = { > > + .enum_mbus_code = t4ka3_enum_mbus_code, > > + .enum_frame_size = t4ka3_enum_frame_size, > > + .get_fmt = t4ka3_get_pad_format, > > + .set_fmt = t4ka3_set_pad_format, > > + .get_selection = t4ka3_get_selection, > > + .set_selection = t4ka3_set_selection, > > +}; > > + > > +static const struct v4l2_subdev_ops t4ka3_ops = { > > + .video = &t4ka3_video_ops, > > + .pad = &t4ka3_pad_ops, > > +}; > > + > > +static const struct v4l2_subdev_internal_ops t4ka3_internal_ops = { > > + .init_state = t4ka3_init_state, > > +}; > > + > > +static int t4ka3_init_controls(struct t4ka3_data *sensor) > > +{ > > + const struct v4l2_ctrl_ops *ops = &t4ka3_ctrl_ops; > > + struct t4ka3_ctrls *ctrls = &sensor->ctrls; > > + struct v4l2_ctrl_handler *hdl = &ctrls->handler; > > + int min, max, def; > > + static const char * const test_pattern_menu[] = { > > + "Disabled", > > + "Solid White", > > + "Color Bars", > > + "Gradient", > > + "Random Data", > > + }; > > + > > + v4l2_ctrl_handler_init(hdl, 4); > > + > > + hdl->lock = &sensor->lock; > > + > > + ctrls->vflip = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_VFLIP, 0, 1, 1, 0); > > + ctrls->hflip = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_HFLIP, 0, 1, 1, 0); > > + > > + ctrls->test_pattern = v4l2_ctrl_new_std_menu_items(hdl, ops, > > + V4L2_CID_TEST_PATTERN, > > + ARRAY_SIZE(test_pattern_menu) - 1, > > + 0, 0, test_pattern_menu); > > + ctrls->link_freq = v4l2_ctrl_new_int_menu(hdl, NULL, V4L2_CID_LINK_FREQ, > > + 0, 0, sensor->link_freq); > > + > > + t4ka3_get_vblank_limits(sensor, &min, &max, &def); > > + ctrls->vblank = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_VBLANK, min, max, 1, def); > > + > > + def = T4KA3_PIXELS_PER_LINE - sensor->mode.fmt.width; > > + ctrls->hblank = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_HBLANK, > > + def, def, 1, def); > > + > > + max = T4KA3_LINES_PER_FRAME_30FPS - T4KA3_COARSE_INTEGRATION_TIME_MARGIN; > > + ctrls->exposure = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_EXPOSURE, > > + 0, max, 1, max); > > + > > + ctrls->gain = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_ANALOGUE_GAIN, > > + T4KA3_MIN_GLOBAL_GAIN_SUPPORTED, > > + T4KA3_MAX_GLOBAL_GAIN_SUPPORTED, > > + 1, T4KA3_MIN_GLOBAL_GAIN_SUPPORTED); > > + > > + if (hdl->error) > > + return hdl->error; > > + > > + ctrls->vflip->flags |= V4L2_CTRL_FLAG_MODIFY_LAYOUT; > > + ctrls->hflip->flags |= V4L2_CTRL_FLAG_MODIFY_LAYOUT; > > + ctrls->link_freq->flags |= V4L2_CTRL_FLAG_READ_ONLY; > > + ctrls->hblank->flags |= V4L2_CTRL_FLAG_READ_ONLY; > > + > > + sensor->sd.ctrl_handler = hdl; > > + return 0; > > +} > > + > > +static int t4ka3_pm_suspend(struct device *dev) > > +{ > > + struct t4ka3_data *sensor = dev_get_drvdata(dev); > > + > > + gpiod_set_value_cansleep(sensor->powerdown_gpio, 1); > > + gpiod_set_value_cansleep(sensor->reset_gpio, 1); > > + > > + return 0; > > +} > > + > > +static int t4ka3_pm_resume(struct device *dev) > > +{ > > + struct t4ka3_data *sensor = dev_get_drvdata(dev); > > + u16 sensor_id; > > + int ret; > > + > > + usleep_range(5000, 6000); > > + > > + gpiod_set_value_cansleep(sensor->powerdown_gpio, 0); > > + gpiod_set_value_cansleep(sensor->reset_gpio, 0); > > + > > + /* waiting for the sensor after powering up */ > > + msleep(20); > > + > > + ret = t4ka3_detect(sensor, &sensor_id); > > + if (ret) { > > + dev_err(sensor->dev, "sensor detect failed\n"); > > + return ret; > > + } > > + > > + return 0; > > +} > > + > > +static DEFINE_RUNTIME_DEV_PM_OPS(t4ka3_pm_ops, t4ka3_pm_suspend, t4ka3_pm_resume, NULL); > > + > > +static void t4ka3_remove(struct i2c_client *client) > > +{ > > + struct v4l2_subdev *sd = i2c_get_clientdata(client); > > + struct t4ka3_data *sensor = to_t4ka3_sensor(sd); > > + > > + v4l2_async_unregister_subdev(&sensor->sd); > > + media_entity_cleanup(&sensor->sd.entity); > > + v4l2_ctrl_handler_free(&sensor->ctrls.handler); > > + > > + /* > > + * Disable runtime PM. In case runtime PM is disabled in the kernel, > > + * make sure to turn power off manually. > > + */ > > + pm_runtime_disable(&client->dev); > > + if (!pm_runtime_status_suspended(&client->dev)) > > + t4ka3_pm_suspend(&client->dev); > > + pm_runtime_set_suspended(&client->dev); > > +} > > + > > +static int t4ka3_probe(struct i2c_client *client) > > +{ > > + struct t4ka3_data *sensor; > > + int ret; > > + > > + /* allocate sensor device & init sub device */ > > + sensor = devm_kzalloc(&client->dev, sizeof(*sensor), GFP_KERNEL); > > + if (!sensor) > > + return -ENOMEM; > > + > > + sensor->dev = &client->dev; > > + > > + ret = t4ka3_check_hwcfg(sensor); > > + if (ret) > > + return ret; > > + > > + mutex_init(&sensor->lock); > > + > > + sensor->link_freq[0] = T4KA3_LINK_FREQ; > > + sensor->mode.crop = t4ka3_default_crop; > > + t4ka3_fill_format(sensor, &sensor->mode.fmt, T4KA3_ACTIVE_WIDTH, T4KA3_ACTIVE_HEIGHT); > > + t4ka3_calc_mode(sensor); > > + > > + v4l2_i2c_subdev_init(&sensor->sd, client, &t4ka3_ops); > > + sensor->sd.internal_ops = &t4ka3_internal_ops; > > + > > + sensor->powerdown_gpio = devm_gpiod_get(&client->dev, "powerdown", > > + GPIOD_OUT_HIGH); > > + if (IS_ERR(sensor->powerdown_gpio)) > > + return dev_err_probe(&client->dev, PTR_ERR(sensor->powerdown_gpio), > > + "getting powerdown GPIO\n"); > > + > > + sensor->reset_gpio = devm_gpiod_get_optional(&client->dev, "reset", > > + GPIOD_OUT_HIGH); > > + if (IS_ERR(sensor->reset_gpio)) > > + return dev_err_probe(&client->dev, PTR_ERR(sensor->reset_gpio), > > + "getting reset GPIO\n"); > > + > > + sensor->regmap = devm_cci_regmap_init_i2c(client, 16); > > + if (IS_ERR(sensor->regmap)) > > + return PTR_ERR(sensor->regmap); > > + > > + ret = t4ka3_pm_resume(sensor->dev); > > + if (ret) > > + return ret; > > + > > + pm_runtime_set_active(&client->dev); > > + pm_runtime_get_noresume(&client->dev); > > + pm_runtime_enable(&client->dev); > > + > > + sensor->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE; > > + sensor->pad.flags = MEDIA_PAD_FL_SOURCE; > > + sensor->sd.entity.function = MEDIA_ENT_F_CAM_SENSOR; > > + > > + ret = t4ka3_init_controls(sensor); > > + if (ret) > > + goto err_controls; > > + > > + ret = media_entity_pads_init(&sensor->sd.entity, 1, &sensor->pad); > > + if (ret) > > + goto err_controls; > > + > > + ret = v4l2_async_register_subdev_sensor(&sensor->sd); > > + if (ret) > > + goto err_media_entity; > > + > > + pm_runtime_set_autosuspend_delay(&client->dev, 1000); > > + pm_runtime_use_autosuspend(&client->dev); > > + pm_runtime_put_autosuspend(&client->dev); > > + > > + return 0; > > + > > +err_media_entity: > > + media_entity_cleanup(&sensor->sd.entity); > > +err_controls: > > + v4l2_ctrl_handler_free(&sensor->ctrls.handler); > > + pm_runtime_disable(&client->dev); > > + pm_runtime_put_noidle(&client->dev); > > + return ret; > > +} > > + > > +static struct acpi_device_id t4ka3_acpi_match[] = { > > + { "XMCC0003" }, > > + {} > > +}; > > +MODULE_DEVICE_TABLE(acpi, t4ka3_acpi_match); > > + > > +static struct i2c_driver t4ka3_driver = { > > + .driver = { > > + .name = "t4ka3", > > + .acpi_match_table = ACPI_PTR(t4ka3_acpi_match), > > + .pm = pm_sleep_ptr(&t4ka3_pm_ops), > > + }, > > + .probe = t4ka3_probe, > > + .remove = t4ka3_remove, > > +}; > > +module_i2c_driver(t4ka3_driver) > > + > > +MODULE_DESCRIPTION("A low-level driver for T4KA3 sensor"); > > +MODULE_AUTHOR("HARVEY LV <harvey.lv@intel.com>"); > > +MODULE_LICENSE("GPL");
diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig index 8ba096b8ebca..6ec51f969b32 100644 --- a/drivers/media/i2c/Kconfig +++ b/drivers/media/i2c/Kconfig @@ -690,6 +690,18 @@ config VIDEO_S5K6A3 This is a V4L2 sensor driver for Samsung S5K6A3 raw camera sensor. +config VIDEO_T4KA3 + tristate "Toshiba T4KA3 sensor support" + depends on ACPI || COMPILE_TEST + depends on GPIOLIB + select V4L2_CCI_I2C + help + This is a Video4Linux2 sensor driver for the Toshiba T4KA3 8 MP + camera sensor. + + To compile this driver as a module, choose M here: the + module will be called t4ka3. + config VIDEO_VGXY61 tristate "ST VGXY61 sensor support" select V4L2_CCI_I2C diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile index fbb988bd067a..ad67ea33ce37 100644 --- a/drivers/media/i2c/Makefile +++ b/drivers/media/i2c/Makefile @@ -129,6 +129,7 @@ obj-$(CONFIG_VIDEO_SAA717X) += saa717x.o obj-$(CONFIG_VIDEO_SAA7185) += saa7185.o obj-$(CONFIG_VIDEO_SONY_BTF_MPX) += sony-btf-mpx.o obj-$(CONFIG_VIDEO_ST_MIPID02) += st-mipid02.o +obj-$(CONFIG_VIDEO_T4KA3) += t4ka3.o obj-$(CONFIG_VIDEO_TC358743) += tc358743.o obj-$(CONFIG_VIDEO_TC358746) += tc358746.o obj-$(CONFIG_VIDEO_TDA1997X) += tda1997x.o diff --git a/drivers/media/i2c/t4ka3.c b/drivers/media/i2c/t4ka3.c new file mode 100644 index 000000000000..ee4455a5e8e4 --- /dev/null +++ b/drivers/media/i2c/t4ka3.c @@ -0,0 +1,1099 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Support for T4KA3 8M camera sensor. + * + * Copyright (C) 2015 Intel Corporation. All Rights Reserved. + * Copyright (C) 2016 XiaoMi, Inc. + * Copyright (C) 2024 Hans de Goede <hansg@kernel.org> + */ + +#include <linux/acpi.h> +#include <linux/bits.h> +#include <linux/delay.h> +#include <linux/dev_printk.h> +#include <linux/device.h> +#include <linux/err.h> +#include <linux/errno.h> +#include <linux/gpio/consumer.h> +#include <linux/i2c.h> +#include <linux/mod_devicetable.h> +#include <linux/mutex.h> +#include <linux/pm_runtime.h> +#include <linux/regmap.h> +#include <linux/types.h> + +#include <media/media-entity.h> +#include <media/v4l2-async.h> +#include <media/v4l2-cci.h> +#include <media/v4l2-common.h> +#include <media/v4l2-ctrls.h> +#include <media/v4l2-fwnode.h> +#include <media/v4l2-subdev.h> + +#define T4KA3_NATIVE_WIDTH 3280 +#define T4KA3_NATIVE_HEIGHT 2464 +#define T4KA3_NATIVE_START_LEFT 0 +#define T4KA3_NATIVE_START_TOP 0 +#define T4KA3_ACTIVE_WIDTH 3280 +#define T4KA3_ACTIVE_HEIGHT 2460 +#define T4KA3_ACTIVE_START_LEFT 0 +#define T4KA3_ACTIVE_START_TOP 2 +#define T4KA3_MIN_CROP_WIDTH 2 +#define T4KA3_MIN_CROP_HEIGHT 2 + +#define T4KA3_PIXELS_PER_LINE 3440 +#define T4KA3_LINES_PER_FRAME_30FPS 2492 +#define T4KA3_FPS 30 +#define T4KA3_PIXEL_RATE \ + (T4KA3_PIXELS_PER_LINE * T4KA3_LINES_PER_FRAME_30FPS * T4KA3_FPS) + +/* + * TODO this really should be derived from the 19.2 MHz xvclk combined + * with the PLL settings. But without a datasheet this is the closest + * approximation possible. + * + * link-freq = pixel_rate * bpp / (lanes * 2) + * (lanes * 2) because CSI lanes use double-data-rate (DDR) signalling. + * bpp = 10 and lanes = 4 + */ +#define T4KA3_LINK_FREQ ((u64)T4KA3_PIXEL_RATE * 10 / 8) + +/* For enum_frame_size() full-size + binned-/quarter-size */ +#define T4KA3_FRAME_SIZES 2 + +#define T4KA3_REG_PRODUCT_ID_HIGH CCI_REG8(0x0000) +#define T4KA3_REG_PRODUCT_ID_LOW CCI_REG8(0x0001) +#define T4KA3_PRODUCT_ID 0x1490 + +#define T4KA3_REG_STREAM CCI_REG8(0x0100) +#define T4KA3_REG_IMG_ORIENTATION CCI_REG8(0x0101) +#define T4KA3_HFLIP_BIT BIT(0) +#define T4KA3_VFLIP_BIT BIT(1) +#define T4KA3_REG_PARAM_HOLD CCI_REG8(0x0104) +#define T4KA3_REG_COARSE_INTEGRATION_TIME CCI_REG16(0x0202) +#define T4KA3_COARSE_INTEGRATION_TIME_MARGIN 6 +#define T4KA3_REG_DIGGAIN_GREEN_R CCI_REG16(0x020e) +#define T4KA3_REG_DIGGAIN_RED CCI_REG16(0x0210) +#define T4KA3_REG_DIGGAIN_BLUE CCI_REG16(0x0212) +#define T4KA3_REG_DIGGAIN_GREEN_B CCI_REG16(0x0214) +#define T4KA3_REG_GLOBAL_GAIN CCI_REG16(0x0234) +#define T4KA3_MIN_GLOBAL_GAIN_SUPPORTED 0x0080 +#define T4KA3_MAX_GLOBAL_GAIN_SUPPORTED 0x07ff +#define T4KA3_REG_FRAME_LENGTH_LINES CCI_REG16(0x0340) /* aka VTS */ +/* FIXME: need a datasheet to verify the min + max vblank values */ +#define T4KA3_MIN_VBLANK 4 +#define T4KA3_MAX_VBLANK 0xffff +#define T4KA3_REG_PIXELS_PER_LINE CCI_REG16(0x0342) /* aka HTS */ +/* These 2 being horz/vert start is a guess (no datasheet), always 0 */ +#define T4KA3_REG_HORZ_START CCI_REG16(0x0344) +#define T4KA3_REG_VERT_START CCI_REG16(0x0346) +/* Always 3279 (T4KA3_NATIVE_WIDTH - 1, window is used to crop */ +#define T4KA3_REG_HORZ_END CCI_REG16(0x0348) +/* Always 2463 (T4KA3_NATIVE_HEIGHT - 1, window is used to crop */ +#define T4KA3_REG_VERT_END CCI_REG16(0x034a) +/* Output size (after cropping/window) */ +#define T4KA3_REG_HORZ_OUTPUT_SIZE CCI_REG16(0x034c) +#define T4KA3_REG_VERT_OUTPUT_SIZE CCI_REG16(0x034e) +/* Window/crop start + size *after* binning */ +#define T4KA3_REG_WIN_START_X CCI_REG16(0x0408) +#define T4KA3_REG_WIN_START_Y CCI_REG16(0x040a) +#define T4KA3_REG_WIN_WIDTH CCI_REG16(0x040c) +#define T4KA3_REG_WIN_HEIGHT CCI_REG16(0x040e) +#define T4KA3_REG_TEST_PATTERN_MODE CCI_REG8(0x0601) +/* Unknown register at address 0x0900 */ +#define T4KA3_REG_0900 CCI_REG8(0x0900) +#define T4KA3_REG_BINNING CCI_REG8(0x0901) +#define T4KA3_BINNING_VAL(_b) \ + ({ typeof(_b) (b) = (_b); \ + ((b) << 4) | (b); }) + +struct t4ka3_ctrls { + struct v4l2_ctrl_handler handler; + struct v4l2_ctrl *hflip; + struct v4l2_ctrl *vflip; + struct v4l2_ctrl *vblank; + struct v4l2_ctrl *hblank; + struct v4l2_ctrl *exposure; + struct v4l2_ctrl *test_pattern; + struct v4l2_ctrl *link_freq; + struct v4l2_ctrl *gain; +}; + +struct t4ka3_mode { + struct v4l2_rect crop; + struct v4l2_mbus_framefmt fmt; + int binning; + u16 win_x; + u16 win_y; +}; + +struct t4ka3_data { + struct v4l2_subdev sd; + struct media_pad pad; + struct mutex lock; /* serialize sensor's ioctl */ + struct t4ka3_ctrls ctrls; + struct t4ka3_mode mode; + struct device *dev; + struct regmap *regmap; + struct gpio_desc *powerdown_gpio; + struct gpio_desc *reset_gpio; + s64 link_freq[1]; + int streaming; +}; + +/* init settings */ +static const struct cci_reg_sequence t4ka3_init_config[] = { + {CCI_REG8(0x4136), 0x13}, + {CCI_REG8(0x4137), 0x33}, + {CCI_REG8(0x3094), 0x01}, + {CCI_REG8(0x0233), 0x01}, + {CCI_REG8(0x4B06), 0x01}, + {CCI_REG8(0x4B07), 0x01}, + {CCI_REG8(0x3028), 0x01}, + {CCI_REG8(0x3032), 0x14}, + {CCI_REG8(0x305C), 0x0C}, + {CCI_REG8(0x306D), 0x0A}, + {CCI_REG8(0x3071), 0xFA}, + {CCI_REG8(0x307E), 0x0A}, + {CCI_REG8(0x307F), 0xFC}, + {CCI_REG8(0x3091), 0x04}, + {CCI_REG8(0x3092), 0x60}, + {CCI_REG8(0x3096), 0xC0}, + {CCI_REG8(0x3100), 0x07}, + {CCI_REG8(0x3101), 0x4C}, + {CCI_REG8(0x3118), 0xCC}, + {CCI_REG8(0x3139), 0x06}, + {CCI_REG8(0x313A), 0x06}, + {CCI_REG8(0x313B), 0x04}, + {CCI_REG8(0x3143), 0x02}, + {CCI_REG8(0x314F), 0x0E}, + {CCI_REG8(0x3169), 0x99}, + {CCI_REG8(0x316A), 0x99}, + {CCI_REG8(0x3171), 0x05}, + {CCI_REG8(0x31A1), 0xA7}, + {CCI_REG8(0x31A2), 0x9C}, + {CCI_REG8(0x31A3), 0x8F}, + {CCI_REG8(0x31A4), 0x75}, + {CCI_REG8(0x31A5), 0xEE}, + {CCI_REG8(0x31A6), 0xEA}, + {CCI_REG8(0x31A7), 0xE4}, + {CCI_REG8(0x31A8), 0xE4}, + {CCI_REG8(0x31DF), 0x05}, + {CCI_REG8(0x31EC), 0x1B}, + {CCI_REG8(0x31ED), 0x1B}, + {CCI_REG8(0x31EE), 0x1B}, + {CCI_REG8(0x31F0), 0x1B}, + {CCI_REG8(0x31F1), 0x1B}, + {CCI_REG8(0x31F2), 0x1B}, + {CCI_REG8(0x3204), 0x3F}, + {CCI_REG8(0x3205), 0x03}, + {CCI_REG8(0x3210), 0x01}, + {CCI_REG8(0x3216), 0x68}, + {CCI_REG8(0x3217), 0x58}, + {CCI_REG8(0x3218), 0x58}, + {CCI_REG8(0x321A), 0x68}, + {CCI_REG8(0x321B), 0x60}, + {CCI_REG8(0x3238), 0x03}, + {CCI_REG8(0x3239), 0x03}, + {CCI_REG8(0x323A), 0x05}, + {CCI_REG8(0x323B), 0x06}, + {CCI_REG8(0x3243), 0x03}, + {CCI_REG8(0x3244), 0x08}, + {CCI_REG8(0x3245), 0x01}, + {CCI_REG8(0x3307), 0x19}, + {CCI_REG8(0x3308), 0x19}, + {CCI_REG8(0x3320), 0x01}, + {CCI_REG8(0x3326), 0x15}, + {CCI_REG8(0x3327), 0x0D}, + {CCI_REG8(0x3328), 0x01}, + {CCI_REG8(0x3380), 0x01}, + {CCI_REG8(0x339E), 0x07}, + {CCI_REG8(0x3424), 0x00}, + {CCI_REG8(0x343C), 0x01}, + {CCI_REG8(0x3398), 0x04}, + {CCI_REG8(0x343A), 0x10}, + {CCI_REG8(0x339A), 0x22}, + {CCI_REG8(0x33B4), 0x00}, + {CCI_REG8(0x3393), 0x01}, + {CCI_REG8(0x33B3), 0x6E}, + {CCI_REG8(0x3433), 0x06}, + {CCI_REG8(0x3433), 0x00}, + {CCI_REG8(0x33B3), 0x00}, + {CCI_REG8(0x3393), 0x03}, + {CCI_REG8(0x33B4), 0x03}, + {CCI_REG8(0x343A), 0x00}, + {CCI_REG8(0x339A), 0x00}, + {CCI_REG8(0x3398), 0x00} +}; + +static const struct cci_reg_sequence t4ka3_pre_mode_set_regs[] = { + {CCI_REG8(0x0112), 0x0A}, + {CCI_REG8(0x0113), 0x0A}, + {CCI_REG8(0x0114), 0x03}, + {CCI_REG8(0x4136), 0x13}, + {CCI_REG8(0x4137), 0x33}, + {CCI_REG8(0x0820), 0x0A}, + {CCI_REG8(0x0821), 0x0D}, + {CCI_REG8(0x0822), 0x00}, + {CCI_REG8(0x0823), 0x00}, + {CCI_REG8(0x0301), 0x0A}, + {CCI_REG8(0x0303), 0x01}, + {CCI_REG8(0x0305), 0x04}, + {CCI_REG8(0x0306), 0x02}, + {CCI_REG8(0x0307), 0x18}, + {CCI_REG8(0x030B), 0x01}, +}; + +static const struct cci_reg_sequence t4ka3_post_mode_set_regs[] = { + {CCI_REG8(0x0902), 0x00}, + {CCI_REG8(0x4220), 0x00}, + {CCI_REG8(0x4222), 0x01}, + {CCI_REG8(0x3380), 0x01}, + {CCI_REG8(0x3090), 0x88}, + {CCI_REG8(0x3394), 0x20}, + {CCI_REG8(0x3090), 0x08}, + {CCI_REG8(0x3394), 0x10} +}; + +static inline struct t4ka3_data *to_t4ka3_sensor(struct v4l2_subdev *sd) +{ + return container_of(sd, struct t4ka3_data, sd); +} + +static inline struct t4ka3_data *ctrl_to_t4ka3(struct v4l2_ctrl *ctrl) +{ + return container_of(ctrl->handler, struct t4ka3_data, ctrls.handler); +} + +/* T4KA3 default GRBG */ +static const int t4ka3_hv_flip_bayer_order[] = { + MEDIA_BUS_FMT_SGRBG10_1X10, + MEDIA_BUS_FMT_SBGGR10_1X10, + MEDIA_BUS_FMT_SRGGB10_1X10, + MEDIA_BUS_FMT_SGBRG10_1X10, +}; + +static const struct v4l2_rect t4ka3_default_crop = { + .left = T4KA3_ACTIVE_START_LEFT, + .top = T4KA3_ACTIVE_START_TOP, + .width = T4KA3_ACTIVE_WIDTH, + .height = T4KA3_ACTIVE_HEIGHT, +}; + +static int t4ka3_detect(struct t4ka3_data *sensor, u16 *id); + +static void t4ka3_set_bayer_order(struct t4ka3_data *sensor, + struct v4l2_mbus_framefmt *fmt) +{ + int hv_flip = 0; + + if (sensor->ctrls.vflip && sensor->ctrls.vflip->val) + hv_flip += 1; + + if (sensor->ctrls.hflip && sensor->ctrls.hflip->val) + hv_flip += 2; + + fmt->code = t4ka3_hv_flip_bayer_order[hv_flip]; +} + +static int t4ka3_update_exposure_range(struct t4ka3_data *sensor) +{ + int exp_max = sensor->mode.fmt.height + sensor->ctrls.vblank->val - + T4KA3_COARSE_INTEGRATION_TIME_MARGIN; + + return __v4l2_ctrl_modify_range(sensor->ctrls.exposure, 0, exp_max, + 1, exp_max); +} + +static struct v4l2_rect * +__t4ka3_get_pad_crop(struct t4ka3_data *sensor, + struct v4l2_subdev_state *state, + unsigned int pad, + enum v4l2_subdev_format_whence which) +{ + if (which == V4L2_SUBDEV_FORMAT_TRY) + return v4l2_subdev_state_get_crop(state, pad); + + return &sensor->mode.crop; +} + +static struct v4l2_mbus_framefmt * +__t4ka3_get_pad_format(struct t4ka3_data *sensor, + struct v4l2_subdev_state *sd_state, unsigned int pad, + enum v4l2_subdev_format_whence which) +{ + if (which == V4L2_SUBDEV_FORMAT_TRY) + return v4l2_subdev_state_get_format(sd_state, pad); + + return &sensor->mode.fmt; +} + +static void t4ka3_fill_format(struct t4ka3_data *sensor, + struct v4l2_mbus_framefmt *fmt, + unsigned int width, unsigned int height) +{ + memset(fmt, 0, sizeof(*fmt)); + fmt->width = width; + fmt->height = height; + fmt->field = V4L2_FIELD_NONE; + fmt->colorspace = V4L2_COLORSPACE_SRGB; + t4ka3_set_bayer_order(sensor, fmt); +} + +static void t4ka3_calc_mode(struct t4ka3_data *sensor) +{ + int width = sensor->mode.fmt.width; + int height = sensor->mode.fmt.height; + int binning; + + if (width <= (sensor->mode.crop.width / 2) && + height <= (sensor->mode.crop.height / 2)) + binning = 2; + else + binning = 1; + + width *= binning; + height *= binning; + + sensor->mode.binning = binning; + sensor->mode.win_x = (sensor->mode.crop.left + + (sensor->mode.crop.width - width) / 2) & ~1; + sensor->mode.win_y = (sensor->mode.crop.top + + (sensor->mode.crop.height - height) / 2) & ~1; + /* + * t4ka's window is done after binning, but must still be a multiple of 2 ? + * Round up to avoid top 2 black lines in 1640x1230 (quarter res) case. + */ + sensor->mode.win_x = DIV_ROUND_UP(sensor->mode.win_x, binning); + sensor->mode.win_y = DIV_ROUND_UP(sensor->mode.win_y, binning); +} + +static void t4ka3_get_vblank_limits(struct t4ka3_data *sensor, int *min, int *max, int *def) +{ + *min = T4KA3_MIN_VBLANK + (sensor->mode.binning - 1) * sensor->mode.fmt.height; + *max = T4KA3_MAX_VBLANK - sensor->mode.fmt.height; + *def = T4KA3_LINES_PER_FRAME_30FPS - sensor->mode.fmt.height; +} + +static int t4ka3_set_pad_format(struct v4l2_subdev *sd, + struct v4l2_subdev_state *sd_state, + struct v4l2_subdev_format *format) +{ + struct t4ka3_data *sensor = to_t4ka3_sensor(sd); + struct v4l2_mbus_framefmt *try_fmt; + const struct v4l2_rect *crop; + unsigned int width, height; + int min, max, def, ret = 0; + + crop = __t4ka3_get_pad_crop(sensor, sd_state, format->pad, format->which); + + /* Limit set_fmt max size to crop width / height */ + width = clamp_val(ALIGN(format->format.width, 2), + T4KA3_MIN_CROP_WIDTH, crop->width); + height = clamp_val(ALIGN(format->format.height, 2), + T4KA3_MIN_CROP_HEIGHT, crop->height); + t4ka3_fill_format(sensor, &format->format, width, height); + + if (format->which == V4L2_SUBDEV_FORMAT_TRY) { + try_fmt = v4l2_subdev_state_get_format(sd_state, 0); + *try_fmt = format->format; + return 0; + } + + mutex_lock(&sensor->lock); + + if (sensor->streaming) { + ret = -EBUSY; + goto unlock; + } + + sensor->mode.fmt = format->format; + t4ka3_calc_mode(sensor); + + /* vblank range is height dependent adjust and reset to default */ + t4ka3_get_vblank_limits(sensor, &min, &max, &def); + ret = __v4l2_ctrl_modify_range(sensor->ctrls.vblank, min, max, 1, def); + if (ret) + goto unlock; + + ret = __v4l2_ctrl_s_ctrl(sensor->ctrls.vblank, def); + if (ret) + goto unlock; + + def = T4KA3_ACTIVE_WIDTH - sensor->mode.fmt.width; + ret = __v4l2_ctrl_modify_range(sensor->ctrls.hblank, def, def, 1, def); + if (ret) + goto unlock; + ret = __v4l2_ctrl_s_ctrl(sensor->ctrls.hblank, def); + if (ret) + goto unlock; + + /* exposure range depends on vts which may have changed */ + ret = t4ka3_update_exposure_range(sensor); + if (ret) + goto unlock; + +unlock: + mutex_unlock(&sensor->lock); + return ret; +} + +/* Horizontal flip the image. */ +static int t4ka3_t_hflip(struct v4l2_subdev *sd, int value) +{ + struct t4ka3_data *sensor = to_t4ka3_sensor(sd); + int ret; + u64 val; + + if (sensor->streaming) + return -EBUSY; + + val = value ? T4KA3_HFLIP_BIT : 0; + + ret = cci_update_bits(sensor->regmap, T4KA3_REG_IMG_ORIENTATION, + T4KA3_HFLIP_BIT, val, NULL); + if (ret) + return ret; + + t4ka3_set_bayer_order(sensor, &sensor->mode.fmt); + return 0; +} + +/* Vertically flip the image */ +static int t4ka3_t_vflip(struct v4l2_subdev *sd, int value) +{ + struct t4ka3_data *sensor = to_t4ka3_sensor(sd); + int ret; + u64 val; + + if (sensor->streaming) + return -EBUSY; + + val = value ? T4KA3_VFLIP_BIT : 0; + + ret = cci_update_bits(sensor->regmap, T4KA3_REG_IMG_ORIENTATION, + T4KA3_VFLIP_BIT, val, NULL); + if (ret) + return ret; + + t4ka3_set_bayer_order(sensor, &sensor->mode.fmt); + return 0; +} + +static int t4ka3_test_pattern(struct t4ka3_data *sensor, s32 value) +{ + return cci_write(sensor->regmap, T4KA3_REG_TEST_PATTERN_MODE, value, NULL); +} + +static int t4ka3_detect(struct t4ka3_data *sensor, u16 *id) +{ + struct i2c_client *client = v4l2_get_subdevdata(&sensor->sd); + struct i2c_adapter *adapter = client->adapter; + u64 high, low; + int ret = 0; + + /* i2c check */ + if (!i2c_check_functionality(adapter, I2C_FUNC_I2C)) + return -ENODEV; + + /* check sensor chip ID */ + cci_read(sensor->regmap, T4KA3_REG_PRODUCT_ID_HIGH, &high, &ret); + cci_read(sensor->regmap, T4KA3_REG_PRODUCT_ID_LOW, &low, &ret); + if (ret) + return ret; + + *id = (((u8)high) << 8) | (u8)low; + if (*id != T4KA3_PRODUCT_ID) { + dev_err(sensor->dev, "main sensor t4ka3 ID error\n"); + return -ENODEV; + } + + return 0; +} + +static int t4ka3_s_ctrl(struct v4l2_ctrl *ctrl) +{ + struct t4ka3_data *sensor = ctrl_to_t4ka3(ctrl); + int ret; + + /* Update exposure range on vblank changes */ + if (ctrl->id == V4L2_CID_VBLANK) { + ret = t4ka3_update_exposure_range(sensor); + if (ret) + return ret; + } + + /* Only apply changes to the controls if the device is powered up */ + if (!pm_runtime_get_if_in_use(sensor->sd.dev)) { + t4ka3_set_bayer_order(sensor, &sensor->mode.fmt); + return 0; + } + + switch (ctrl->id) { + case V4L2_CID_TEST_PATTERN: + ret = t4ka3_test_pattern(sensor, ctrl->val); + break; + case V4L2_CID_VFLIP: + ret = t4ka3_t_vflip(&sensor->sd, ctrl->val); + break; + case V4L2_CID_HFLIP: + ret = t4ka3_t_hflip(&sensor->sd, ctrl->val); + break; + case V4L2_CID_VBLANK: + ret = cci_write(sensor->regmap, T4KA3_REG_FRAME_LENGTH_LINES, + sensor->mode.fmt.height + ctrl->val, NULL); + break; + case V4L2_CID_EXPOSURE: + ret = cci_write(sensor->regmap, T4KA3_REG_COARSE_INTEGRATION_TIME, + ctrl->val, NULL); + break; + case V4L2_CID_ANALOGUE_GAIN: + ret = cci_write(sensor->regmap, T4KA3_REG_GLOBAL_GAIN, + ctrl->val, NULL); + break; + default: + ret = -EINVAL; + break; + } + + pm_runtime_put(sensor->sd.dev); + return ret; +} + +static int t4ka3_set_mode(struct t4ka3_data *sensor) +{ + int ret = 0; + + cci_write(sensor->regmap, T4KA3_REG_HORZ_OUTPUT_SIZE, sensor->mode.fmt.width, &ret); + /* Write mode-height - 2 otherwise things don't work, hw-bug ? */ + cci_write(sensor->regmap, T4KA3_REG_VERT_OUTPUT_SIZE, sensor->mode.fmt.height - 2, &ret); + /* Note overwritten by __v4l2_ctrl_handler_setup() based on vblank ctrl */ + cci_write(sensor->regmap, T4KA3_REG_FRAME_LENGTH_LINES, T4KA3_LINES_PER_FRAME_30FPS, &ret); + cci_write(sensor->regmap, T4KA3_REG_PIXELS_PER_LINE, T4KA3_PIXELS_PER_LINE, &ret); + /* Always use the full sensor, using window to crop */ + cci_write(sensor->regmap, T4KA3_REG_HORZ_START, 0, &ret); + cci_write(sensor->regmap, T4KA3_REG_VERT_START, 0, &ret); + cci_write(sensor->regmap, T4KA3_REG_HORZ_END, T4KA3_NATIVE_WIDTH - 1, &ret); + cci_write(sensor->regmap, T4KA3_REG_VERT_END, T4KA3_NATIVE_HEIGHT - 1, &ret); + /* Set window */ + cci_write(sensor->regmap, T4KA3_REG_WIN_START_X, sensor->mode.win_x, &ret); + cci_write(sensor->regmap, T4KA3_REG_WIN_START_Y, sensor->mode.win_y, &ret); + cci_write(sensor->regmap, T4KA3_REG_WIN_WIDTH, sensor->mode.fmt.width, &ret); + cci_write(sensor->regmap, T4KA3_REG_WIN_HEIGHT, sensor->mode.fmt.height, &ret); + /* Write 1 to unknown register 0x0900 */ + cci_write(sensor->regmap, T4KA3_REG_0900, 1, &ret); + cci_write(sensor->regmap, T4KA3_REG_BINNING, T4KA3_BINNING_VAL(sensor->mode.binning), &ret); + + return ret; +} + +static int t4ka3_s_stream(struct v4l2_subdev *sd, int enable) +{ + struct t4ka3_data *sensor = to_t4ka3_sensor(sd); + int ret; + + mutex_lock(&sensor->lock); + + if (sensor->streaming == enable) { + dev_warn(sensor->dev, "Stream already %s\n", enable ? "started" : "stopped"); + ret = -EBUSY; + goto error_unlock; + } + + if (enable) { + ret = pm_runtime_get_sync(sensor->sd.dev); + if (ret < 0) { + dev_err(sensor->dev, "power-up err.\n"); + goto error_unlock; + } + + cci_multi_reg_write(sensor->regmap, t4ka3_init_config, + ARRAY_SIZE(t4ka3_init_config), &ret); + /* enable group hold */ + cci_write(sensor->regmap, T4KA3_REG_PARAM_HOLD, 1, &ret); + cci_multi_reg_write(sensor->regmap, t4ka3_pre_mode_set_regs, + ARRAY_SIZE(t4ka3_pre_mode_set_regs), &ret); + if (ret) + goto error_powerdown; + + ret = t4ka3_set_mode(sensor); + if (ret) + goto error_powerdown; + + ret = cci_multi_reg_write(sensor->regmap, t4ka3_post_mode_set_regs, + ARRAY_SIZE(t4ka3_post_mode_set_regs), NULL); + if (ret) + goto error_powerdown; + + /* Restore value of all ctrls */ + ret = __v4l2_ctrl_handler_setup(&sensor->ctrls.handler); + if (ret) + goto error_powerdown; + + /* disable group hold */ + cci_write(sensor->regmap, T4KA3_REG_PARAM_HOLD, 0, &ret); + cci_write(sensor->regmap, T4KA3_REG_STREAM, 1, &ret); + if (ret) + goto error_powerdown; + + sensor->streaming = 1; + } else { + ret = cci_write(sensor->regmap, T4KA3_REG_STREAM, 0, NULL); + if (ret) + goto error_powerdown; + + ret = pm_runtime_put(sensor->sd.dev); + if (ret) + goto error_unlock; + + sensor->streaming = 0; + } + + mutex_unlock(&sensor->lock); + return ret; + +error_powerdown: + pm_runtime_put(sensor->sd.dev); +error_unlock: + mutex_unlock(&sensor->lock); + return ret; +} + +static int t4ka3_get_selection(struct v4l2_subdev *sd, + struct v4l2_subdev_state *state, + struct v4l2_subdev_selection *sel) +{ + struct t4ka3_data *sensor = to_t4ka3_sensor(sd); + + switch (sel->target) { + case V4L2_SEL_TGT_CROP: + mutex_lock(&sensor->lock); + sel->r = *__t4ka3_get_pad_crop(sensor, state, sel->pad, + sel->which); + mutex_unlock(&sensor->lock); + break; + case V4L2_SEL_TGT_NATIVE_SIZE: + case V4L2_SEL_TGT_CROP_BOUNDS: + sel->r.top = 0; + sel->r.left = 0; + sel->r.width = T4KA3_NATIVE_WIDTH; + sel->r.height = T4KA3_NATIVE_HEIGHT; + break; + case V4L2_SEL_TGT_CROP_DEFAULT: + sel->r = t4ka3_default_crop; + break; + default: + return -EINVAL; + } + + return 0; +} + +static int t4ka3_set_selection(struct v4l2_subdev *sd, + struct v4l2_subdev_state *state, + struct v4l2_subdev_selection *sel) +{ + struct t4ka3_data *sensor = to_t4ka3_sensor(sd); + struct v4l2_mbus_framefmt *format; + struct v4l2_rect *crop; + struct v4l2_rect rect; + + if (sel->target != V4L2_SEL_TGT_CROP) + return -EINVAL; + + /* + * Clamp the boundaries of the crop rectangle to the size of the sensor + * pixel array. Align to multiples of 2 to ensure Bayer pattern isn't + * disrupted. + */ + rect.left = clamp_val(ALIGN(sel->r.left, 2), + T4KA3_NATIVE_START_LEFT, T4KA3_NATIVE_WIDTH); + rect.top = clamp_val(ALIGN(sel->r.top, 2), + T4KA3_NATIVE_START_TOP, T4KA3_NATIVE_HEIGHT); + rect.width = clamp_val(ALIGN(sel->r.width, 2), + T4KA3_MIN_CROP_WIDTH, T4KA3_NATIVE_WIDTH); + rect.height = clamp_val(ALIGN(sel->r.height, 2), + T4KA3_MIN_CROP_HEIGHT, T4KA3_NATIVE_HEIGHT); + + /* Make sure the crop rectangle isn't outside the bounds of the array */ + rect.width = min_t(unsigned int, rect.width, + T4KA3_NATIVE_WIDTH - rect.left); + rect.height = min_t(unsigned int, rect.height, + T4KA3_NATIVE_HEIGHT - rect.top); + + crop = __t4ka3_get_pad_crop(sensor, state, sel->pad, sel->which); + + mutex_lock(&sensor->lock); + + *crop = rect; + + if (rect.width != crop->width || rect.height != crop->height) { + /* + * Reset the output image size if the crop rectangle size has + * been modified. + */ + format = __t4ka3_get_pad_format(sensor, state, sel->pad, + sel->which); + format->width = rect.width; + format->height = rect.height; + if (sel->which == V4L2_SUBDEV_FORMAT_ACTIVE) + t4ka3_calc_mode(sensor); + } + + mutex_unlock(&sensor->lock); + + sel->r = rect; + + return 0; +} + +static int +t4ka3_enum_mbus_code(struct v4l2_subdev *sd, + struct v4l2_subdev_state *sd_state, + struct v4l2_subdev_mbus_code_enum *code) +{ + if (code->index) + return -EINVAL; + + code->code = MEDIA_BUS_FMT_SGRBG10_1X10; + return 0; +} + +static int t4ka3_enum_frame_size(struct v4l2_subdev *sd, + struct v4l2_subdev_state *sd_state, + struct v4l2_subdev_frame_size_enum *fse) +{ + struct t4ka3_data *sensor = to_t4ka3_sensor(sd); + struct v4l2_rect *crop; + + if (fse->index >= T4KA3_FRAME_SIZES) + return -EINVAL; + + crop = __t4ka3_get_pad_crop(sensor, sd_state, fse->pad, fse->which); + if (!crop) + return -EINVAL; + + fse->min_width = crop->width / (fse->index + 1); + fse->min_height = crop->height / (fse->index + 1); + fse->max_width = fse->min_width; + fse->max_height = fse->min_height; + + return 0; +} + +static int +t4ka3_get_pad_format(struct v4l2_subdev *sd, + struct v4l2_subdev_state *sd_state, + struct v4l2_subdev_format *fmt) +{ + struct t4ka3_data *sensor = to_t4ka3_sensor(sd); + struct v4l2_mbus_framefmt *format = + __t4ka3_get_pad_format(sensor, sd_state, fmt->pad, fmt->which); + + fmt->format = *format; + return 0; +} + +static int t4ka3_check_hwcfg(struct t4ka3_data *sensor) +{ + struct fwnode_handle *fwnode = dev_fwnode(sensor->dev); + struct v4l2_fwnode_endpoint bus_cfg = { + .bus_type = V4L2_MBUS_CSI2_DPHY, + }; + struct fwnode_handle *endpoint; + unsigned int i; + int ret; + + /* + * Sometimes the fwnode graph is initialized by the bridge driver. + * Bridge drivers doing this may also add GPIO mappings, wait for this. + */ + endpoint = fwnode_graph_get_next_endpoint(fwnode, NULL); + if (!endpoint) + return dev_err_probe(sensor->dev, -EPROBE_DEFER, + "waiting for fwnode graph endpoint\n"); + + ret = v4l2_fwnode_endpoint_alloc_parse(endpoint, &bus_cfg); + fwnode_handle_put(endpoint); + if (ret) + return ret; + + if (bus_cfg.bus.mipi_csi2.num_data_lanes != 4) { + dev_err(sensor->dev, "only a 4-lane CSI2 config is supported"); + ret = -EINVAL; + goto out_free_bus_cfg; + } + + if (!bus_cfg.nr_of_link_frequencies) { + dev_err(sensor->dev, "no link frequencies defined\n"); + ret = -EINVAL; + goto out_free_bus_cfg; + } + + for (i = 0; i < bus_cfg.nr_of_link_frequencies; i++) { + if (bus_cfg.link_frequencies[i] == T4KA3_LINK_FREQ) + break; + } + + if (i == bus_cfg.nr_of_link_frequencies) { + dev_err(sensor->dev, "supported link freq %llu not found\n", + T4KA3_LINK_FREQ); + ret = -EINVAL; + goto out_free_bus_cfg; + } + +out_free_bus_cfg: + v4l2_fwnode_endpoint_free(&bus_cfg); + + return ret; +} + +static int t4ka3_init_state(struct v4l2_subdev *sd, + struct v4l2_subdev_state *sd_state) +{ + struct t4ka3_data *sensor = to_t4ka3_sensor(sd); + + *v4l2_subdev_state_get_crop(sd_state, 0) = t4ka3_default_crop; + + t4ka3_fill_format(sensor, v4l2_subdev_state_get_format(sd_state, 0), + T4KA3_ACTIVE_WIDTH, T4KA3_ACTIVE_HEIGHT); + return 0; +} + +static const struct v4l2_ctrl_ops t4ka3_ctrl_ops = { + .s_ctrl = t4ka3_s_ctrl, +}; + +static const struct v4l2_subdev_video_ops t4ka3_video_ops = { + .s_stream = t4ka3_s_stream, +}; + +static const struct v4l2_subdev_pad_ops t4ka3_pad_ops = { + .enum_mbus_code = t4ka3_enum_mbus_code, + .enum_frame_size = t4ka3_enum_frame_size, + .get_fmt = t4ka3_get_pad_format, + .set_fmt = t4ka3_set_pad_format, + .get_selection = t4ka3_get_selection, + .set_selection = t4ka3_set_selection, +}; + +static const struct v4l2_subdev_ops t4ka3_ops = { + .video = &t4ka3_video_ops, + .pad = &t4ka3_pad_ops, +}; + +static const struct v4l2_subdev_internal_ops t4ka3_internal_ops = { + .init_state = t4ka3_init_state, +}; + +static int t4ka3_init_controls(struct t4ka3_data *sensor) +{ + const struct v4l2_ctrl_ops *ops = &t4ka3_ctrl_ops; + struct t4ka3_ctrls *ctrls = &sensor->ctrls; + struct v4l2_ctrl_handler *hdl = &ctrls->handler; + int min, max, def; + static const char * const test_pattern_menu[] = { + "Disabled", + "Solid White", + "Color Bars", + "Gradient", + "Random Data", + }; + + v4l2_ctrl_handler_init(hdl, 4); + + hdl->lock = &sensor->lock; + + ctrls->vflip = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_VFLIP, 0, 1, 1, 0); + ctrls->hflip = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_HFLIP, 0, 1, 1, 0); + + ctrls->test_pattern = v4l2_ctrl_new_std_menu_items(hdl, ops, + V4L2_CID_TEST_PATTERN, + ARRAY_SIZE(test_pattern_menu) - 1, + 0, 0, test_pattern_menu); + ctrls->link_freq = v4l2_ctrl_new_int_menu(hdl, NULL, V4L2_CID_LINK_FREQ, + 0, 0, sensor->link_freq); + + t4ka3_get_vblank_limits(sensor, &min, &max, &def); + ctrls->vblank = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_VBLANK, min, max, 1, def); + + def = T4KA3_PIXELS_PER_LINE - sensor->mode.fmt.width; + ctrls->hblank = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_HBLANK, + def, def, 1, def); + + max = T4KA3_LINES_PER_FRAME_30FPS - T4KA3_COARSE_INTEGRATION_TIME_MARGIN; + ctrls->exposure = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_EXPOSURE, + 0, max, 1, max); + + ctrls->gain = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_ANALOGUE_GAIN, + T4KA3_MIN_GLOBAL_GAIN_SUPPORTED, + T4KA3_MAX_GLOBAL_GAIN_SUPPORTED, + 1, T4KA3_MIN_GLOBAL_GAIN_SUPPORTED); + + if (hdl->error) + return hdl->error; + + ctrls->vflip->flags |= V4L2_CTRL_FLAG_MODIFY_LAYOUT; + ctrls->hflip->flags |= V4L2_CTRL_FLAG_MODIFY_LAYOUT; + ctrls->link_freq->flags |= V4L2_CTRL_FLAG_READ_ONLY; + ctrls->hblank->flags |= V4L2_CTRL_FLAG_READ_ONLY; + + sensor->sd.ctrl_handler = hdl; + return 0; +} + +static int t4ka3_pm_suspend(struct device *dev) +{ + struct t4ka3_data *sensor = dev_get_drvdata(dev); + + gpiod_set_value_cansleep(sensor->powerdown_gpio, 1); + gpiod_set_value_cansleep(sensor->reset_gpio, 1); + + return 0; +} + +static int t4ka3_pm_resume(struct device *dev) +{ + struct t4ka3_data *sensor = dev_get_drvdata(dev); + u16 sensor_id; + int ret; + + usleep_range(5000, 6000); + + gpiod_set_value_cansleep(sensor->powerdown_gpio, 0); + gpiod_set_value_cansleep(sensor->reset_gpio, 0); + + /* waiting for the sensor after powering up */ + msleep(20); + + ret = t4ka3_detect(sensor, &sensor_id); + if (ret) { + dev_err(sensor->dev, "sensor detect failed\n"); + return ret; + } + + return 0; +} + +static DEFINE_RUNTIME_DEV_PM_OPS(t4ka3_pm_ops, t4ka3_pm_suspend, t4ka3_pm_resume, NULL); + +static void t4ka3_remove(struct i2c_client *client) +{ + struct v4l2_subdev *sd = i2c_get_clientdata(client); + struct t4ka3_data *sensor = to_t4ka3_sensor(sd); + + v4l2_async_unregister_subdev(&sensor->sd); + media_entity_cleanup(&sensor->sd.entity); + v4l2_ctrl_handler_free(&sensor->ctrls.handler); + + /* + * Disable runtime PM. In case runtime PM is disabled in the kernel, + * make sure to turn power off manually. + */ + pm_runtime_disable(&client->dev); + if (!pm_runtime_status_suspended(&client->dev)) + t4ka3_pm_suspend(&client->dev); + pm_runtime_set_suspended(&client->dev); +} + +static int t4ka3_probe(struct i2c_client *client) +{ + struct t4ka3_data *sensor; + int ret; + + /* allocate sensor device & init sub device */ + sensor = devm_kzalloc(&client->dev, sizeof(*sensor), GFP_KERNEL); + if (!sensor) + return -ENOMEM; + + sensor->dev = &client->dev; + + ret = t4ka3_check_hwcfg(sensor); + if (ret) + return ret; + + mutex_init(&sensor->lock); + + sensor->link_freq[0] = T4KA3_LINK_FREQ; + sensor->mode.crop = t4ka3_default_crop; + t4ka3_fill_format(sensor, &sensor->mode.fmt, T4KA3_ACTIVE_WIDTH, T4KA3_ACTIVE_HEIGHT); + t4ka3_calc_mode(sensor); + + v4l2_i2c_subdev_init(&sensor->sd, client, &t4ka3_ops); + sensor->sd.internal_ops = &t4ka3_internal_ops; + + sensor->powerdown_gpio = devm_gpiod_get(&client->dev, "powerdown", + GPIOD_OUT_HIGH); + if (IS_ERR(sensor->powerdown_gpio)) + return dev_err_probe(&client->dev, PTR_ERR(sensor->powerdown_gpio), + "getting powerdown GPIO\n"); + + sensor->reset_gpio = devm_gpiod_get_optional(&client->dev, "reset", + GPIOD_OUT_HIGH); + if (IS_ERR(sensor->reset_gpio)) + return dev_err_probe(&client->dev, PTR_ERR(sensor->reset_gpio), + "getting reset GPIO\n"); + + sensor->regmap = devm_cci_regmap_init_i2c(client, 16); + if (IS_ERR(sensor->regmap)) + return PTR_ERR(sensor->regmap); + + ret = t4ka3_pm_resume(sensor->dev); + if (ret) + return ret; + + pm_runtime_set_active(&client->dev); + pm_runtime_get_noresume(&client->dev); + pm_runtime_enable(&client->dev); + + sensor->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE; + sensor->pad.flags = MEDIA_PAD_FL_SOURCE; + sensor->sd.entity.function = MEDIA_ENT_F_CAM_SENSOR; + + ret = t4ka3_init_controls(sensor); + if (ret) + goto err_controls; + + ret = media_entity_pads_init(&sensor->sd.entity, 1, &sensor->pad); + if (ret) + goto err_controls; + + ret = v4l2_async_register_subdev_sensor(&sensor->sd); + if (ret) + goto err_media_entity; + + pm_runtime_set_autosuspend_delay(&client->dev, 1000); + pm_runtime_use_autosuspend(&client->dev); + pm_runtime_put_autosuspend(&client->dev); + + return 0; + +err_media_entity: + media_entity_cleanup(&sensor->sd.entity); +err_controls: + v4l2_ctrl_handler_free(&sensor->ctrls.handler); + pm_runtime_disable(&client->dev); + pm_runtime_put_noidle(&client->dev); + return ret; +} + +static struct acpi_device_id t4ka3_acpi_match[] = { + { "XMCC0003" }, + {} +}; +MODULE_DEVICE_TABLE(acpi, t4ka3_acpi_match); + +static struct i2c_driver t4ka3_driver = { + .driver = { + .name = "t4ka3", + .acpi_match_table = ACPI_PTR(t4ka3_acpi_match), + .pm = pm_sleep_ptr(&t4ka3_pm_ops), + }, + .probe = t4ka3_probe, + .remove = t4ka3_remove, +}; +module_i2c_driver(t4ka3_driver) + +MODULE_DESCRIPTION("A low-level driver for T4KA3 sensor"); +MODULE_AUTHOR("HARVEY LV <harvey.lv@intel.com>"); +MODULE_LICENSE("GPL");