diff -u cx23885/cimax2.c cx23885-commell/cimax2.c
--- cx23885/cimax2.c	2010-02-15 23:22:38.000000000 +0100
+++ cx23885-commell/cimax2.c	2009-11-11 09:36:16.000000000 +0100
@@ -75,7 +75,6 @@
 	void *priv;
 };
 
-struct mutex gpio_mutex;/* Two CiMax's uses same GPIO lines */
 
 int netup_read_i2c(struct i2c_adapter *i2c_adap, u8 addr, u8 reg,
 						u8 *buf, int len)
@@ -183,10 +182,11 @@
 	if (ret != 0)
 		return ret;
 
-	mutex_lock(&gpio_mutex);
+	mutex_lock(&dev->gpio_lock);
 
 	/* write addr */
 	cx_write(MC417_OEN, NETUP_EN_ALL);
+	msleep(2);
 	cx_write(MC417_RWD, NETUP_CTRL_OFF |
 				NETUP_ADLO | (0xff & addr));
 	cx_clear(MC417_RWD, NETUP_ADLO);
@@ -194,9 +194,10 @@
 				NETUP_ADHI | (0xff & (addr >> 8)));
 	cx_clear(MC417_RWD, NETUP_ADHI);
 
-	if (read) /* data in */
+	if (read) { /* data in */
 		cx_write(MC417_OEN, NETUP_EN_ALL | NETUP_DATA);
-	else /* data out */
+		msleep(2);
+	} else /* data out */
 		cx_write(MC417_RWD, NETUP_CTRL_OFF | data);
 
 	/* choose chip */
@@ -206,7 +207,7 @@
 	cx_clear(MC417_RWD, (read) ? NETUP_RD : NETUP_WR);
 	mem = netup_ci_get_mem(dev);
 
-	mutex_unlock(&gpio_mutex);
+	mutex_unlock(&dev->gpio_lock);
 
 	if (!read)
 		if (mem < 0)
@@ -295,10 +296,18 @@
 }
 
 /* work handler */
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2, 6, 20)
+static void netup_read_ci_status(void *_state)
+#else
 static void netup_read_ci_status(struct work_struct *work)
+#endif
 {
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2, 6, 20)
+	struct netup_ci_state *state = _state;
+#else
 	struct netup_ci_state *state =
 			container_of(work, struct netup_ci_state, work);
+#endif
 	u8 buf[33];
 	int ret;
 
@@ -403,7 +412,6 @@
 	switch (port->nr) {
 	case 1:
 		state->ci_i2c_addr = 0x40;
-		mutex_init(&gpio_mutex);
 		break;
 	case 2:
 		state->ci_i2c_addr = 0x41;
@@ -442,7 +450,12 @@
 	if (0 != ret)
 		goto err;
 
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2, 6, 20)
+	INIT_WORK(&state->work, netup_read_ci_status, state);
+#else
 	INIT_WORK(&state->work, netup_read_ci_status);
+#endif
+	schedule_work(&state->work);
 
 	ci_dbg_print("%s: CI initialized!\n", __func__);
 
diff -u cx23885/cx23885-417.c cx23885-commell/cx23885-417.c
--- cx23885/cx23885-417.c	2010-02-15 23:22:38.000000000 +0100
+++ cx23885-commell/cx23885-417.c	2009-11-11 09:36:16.000000000 +0100
@@ -37,6 +37,7 @@
 #include <media/cx2341x.h>
 
 #include "cx23885.h"
+#include "cx23885-ioctl.h"
 
 #define CX23885_FIRM_IMAGE_SIZE 376836
 #define CX23885_FIRM_IMAGE_NAME "v4l-cx23885-enc.fw"
@@ -318,7 +319,7 @@
 	}
 }
 
-static int mc417_register_write(struct cx23885_dev *dev, u16 address, u32 value)
+int mc417_register_write(struct cx23885_dev *dev, u16 address, u32 value)
 {
 	u32 regval;
 
@@ -382,7 +383,7 @@
 	return mc417_wait_ready(dev);
 }
 
-static int mc417_register_read(struct cx23885_dev *dev, u16 address, u32 *value)
+int mc417_register_read(struct cx23885_dev *dev, u16 address, u32 *value)
 {
 	int retval;
 	u32 regval;
@@ -630,6 +631,39 @@
 	return retval;
 }
 
+void mc417_gpio_set(struct cx23885_dev *dev, u32 mask)
+{
+	u32 val;
+
+	/* Set the gpio value */
+	mc417_register_read(dev, 0x900C, &val);
+	val |= (mask & 0x000ffff);
+	mc417_register_write(dev, 0x900C, val);
+}
+
+void mc417_gpio_clear(struct cx23885_dev *dev, u32 mask)
+{
+	u32 val;
+
+	/* Clear the gpio value */
+	mc417_register_read(dev, 0x900C, &val);
+	val &= ~(mask & 0x0000ffff);
+	mc417_register_write(dev, 0x900C, val);
+}
+
+void mc417_gpio_enable(struct cx23885_dev *dev, u32 mask, int asoutput)
+{
+	u32 val;
+
+	/* Enable GPIO direction bits */
+	mc417_register_read(dev, 0x9020, &val);
+	if (asoutput)
+		val |= (mask & 0x0000ffff);
+	else
+		val &= ~(mask & 0x0000ffff);
+
+	mc417_register_write(dev, 0x9020, val);
+}
 /* ------------------------------------------------------------------ */
 
 /* MPEG encoder API */
@@ -955,25 +989,8 @@
 	retval |= mc417_register_write(dev, IVTV_REG_HW_BLOCKS,
 		IVTV_CMD_HW_BLOCKS_RST);
 
-	/* Restore GPIO settings, make sure EIO14 is enabled as an output. */
-	dprintk(2, "%s: GPIO output EIO 0-15 was = 0x%x\n",
-		__func__, gpio_output);
-	/* Power-up seems to have GPIOs AFU. This was causing digital side
-	 * to fail at power-up. Seems GPIOs should be set to 0x10ff0411 at
-	 * power-up.
-	 * gpio_output |= (1<<14);
-	 */
-	/* Note: GPIO14 is specific to the HVR1800 here */
-	gpio_output = 0x10ff0411 | (1<<14);
-	retval |= mc417_register_write(dev, 0x9020, gpio_output | (1<<14));
-	dprintk(2, "%s: GPIO output EIO 0-15 now = 0x%x\n",
-		__func__, gpio_output);
-
-	dprintk(1, "%s: GPIO value  EIO 0-15 was = 0x%x\n",
-		__func__, value);
-	value |= (1<<14);
-	dprintk(1, "%s: GPIO value  EIO 0-15 now = 0x%x\n",
-		__func__, value);
+	/* F/W power up disturbs the GPIOs, restore state */
+	retval |= mc417_register_write(dev, 0x9020, gpio_output);
 	retval |= mc417_register_write(dev, 0x900C, value);
 
 	retval |= mc417_register_read(dev, IVTV_REG_VPU, &value);
@@ -1191,6 +1208,13 @@
 	if (i == ARRAY_SIZE(cx23885_tvnorms))
 		return -EINVAL;
 	dev->encodernorm = cx23885_tvnorms[i];
+#if 0
+	/* Notify the video decoder and other i2c clients.
+	 * This will likely need to be enabled for non NTSC
+	 * formats.
+	 */
+	call_all(dev, core, s_std, id);
+#endif
 	return 0;
 }
 
@@ -1708,6 +1732,11 @@
 	.vidioc_log_status	 = vidioc_log_status,
 	.vidioc_querymenu	 = vidioc_querymenu,
 	.vidioc_queryctrl	 = vidioc_queryctrl,
+	.vidioc_g_chip_ident	 = cx23885_g_chip_ident,
+#ifdef CONFIG_VIDEO_ADV_DEBUG
+	.vidioc_g_register	 = cx23885_g_register,
+	.vidioc_s_register	 = cx23885_s_register,
+#endif
 };
 
 static struct video_device cx23885_mpeg_template = {
@@ -1788,9 +1817,6 @@
 		return err;
 	}
 
-	/* Initialize MC417 registers */
-	cx23885_mc417_init(dev);
-
 	printk(KERN_INFO "%s: registered device video%d [mpeg]\n",
 	       dev->name, dev->v4l_device->num);
 
diff -u cx23885/cx23885-cards.c cx23885-commell/cx23885-cards.c
--- cx23885/cx23885-cards.c	2010-02-15 23:22:38.000000000 +0100
+++ cx23885-commell/cx23885-cards.c	2009-11-11 09:36:16.000000000 +0100
@@ -25,9 +25,11 @@
 #include <linux/delay.h>
 #include <media/cx25840.h>
 
+#include "compat.h"
 #include "cx23885.h"
 #include "tuner-xc2028.h"
 #include "netup-init.h"
+#include "cx23888-ir.h"
 
 /* ------------------------------------------------------------------ */
 /* board config info                                                  */
@@ -201,6 +203,42 @@
 		.name		= "Mygica X8506 DMB-TH",
 		.portb		= CX23885_MPEG_DVB,
 	},
+	[CX23885_BOARD_MAGICPRO_PROHDTVE2] = {
+		.name		= "Magic-Pro ProHDTV Extreme 2",
+		.portb		= CX23885_MPEG_DVB,
+	},
+	[CX23885_BOARD_HAUPPAUGE_HVR1850] = {
+		.name		= "Hauppauge WinTV-HVR1850",
+		.portb		= CX23885_MPEG_ENCODER,
+		.portc		= CX23885_MPEG_DVB,
+	},
+	[CX23885_BOARD_COMPRO_VIDEOMATE_E800] = {
+		.name		= "Compro VideoMate E800",
+		.portc		= CX23885_MPEG_DVB,
+	},
+	[CX23885_BOARD_MPX885] = {
+	    .name       = "MPX-885",
+        .porta      = CX23885_ANALOG_VIDEO,
+        .portb      = CX23885_MPEG_ENCODER,
+        .portc      = CX23885_MPEG_DVB,
+        .input          = {{
+            .type   = CX23885_VMUX_COMPOSITE1,
+            .vmux   = CX25840_VIN1_CH1,
+            .gpio0  = 0,
+        }, {
+            .type   = CX23885_VMUX_COMPOSITE2,
+            .vmux   = CX25840_VIN2_CH1,
+            .gpio0  = 0,
+        }, {
+            .type   = CX23885_VMUX_COMPOSITE3,
+            .vmux   = CX25840_VIN3_CH1,
+            .gpio0  = 0,
+        }, {
+            .type   = CX23885_VMUX_COMPOSITE4,
+            .vmux   = CX25840_VIN4_CH1,
+            .gpio0  = 0,
+        } },
+    },
 };
 const unsigned int cx23885_bcount = ARRAY_SIZE(cx23885_boards);
 
@@ -324,7 +362,23 @@
 		.subvendor = 0x14f1,
 		.subdevice = 0x8651,
 		.card      = CX23885_BOARD_MYGICA_X8506,
-	},
+	}, {
+		.subvendor = 0x14f1,
+		.subdevice = 0x8657,
+		.card      = CX23885_BOARD_MAGICPRO_PROHDTVE2,
+	}, {
+		.subvendor = 0x0070,
+		.subdevice = 0x8541,
+		.card      = CX23885_BOARD_HAUPPAUGE_HVR1850,
+	}, {
+		.subvendor = 0x1858,
+		.subdevice = 0xe800,
+		.card      = CX23885_BOARD_COMPRO_VIDEOMATE_E800,
+	}, {
+	    .subvendor = 0x0,
+        .subdevice = 0x0,
+        .card      = CX23885_BOARD_MPX885,
+    },
 };
 const unsigned int cx23885_idcount = ARRAY_SIZE(cx23885_subids);
 
@@ -483,8 +537,13 @@
 		/* WinTV-HVR1700 (PCIe, OEM, No IR, full height)
 		 * DVB-T and MPEG2 HW Encoder */
 		break;
+	case 85021:
+		/* WinTV-HVR1850 (PCIe, OEM, RCA in, IR, FM,
+			Dual channel ATSC and MPEG2 HW Encoder */
+		break;
 	default:
-		printk(KERN_WARNING "%s: warning: unknown hauppauge model #%d\n",
+		printk(KERN_WARNING "%s: warning: "
+			"unknown hauppauge model #%d\n",
 			dev->name, tv.model);
 		break;
 	}
@@ -514,6 +573,7 @@
 	case CX23885_BOARD_HAUPPAUGE_HVR1500Q:
 	case CX23885_BOARD_LEADTEK_WINFAST_PXDVR3200_H:
 	case CX23885_BOARD_COMPRO_VIDEOMATE_E650F:
+	case CX23885_BOARD_COMPRO_VIDEOMATE_E800:
 		/* Tuner Reset Command */
 		bitmask = 0x04;
 		break;
@@ -574,13 +634,23 @@
 		/* CX23417 GPIO's */
 		/* EIO15 Zilog Reset */
 		/* EIO14 S5H1409/CX24227 Reset */
+		mc417_gpio_enable(dev, GPIO_15 | GPIO_14, 1);
+
+		/* Put the demod into reset and protect the eeprom */
+		mc417_gpio_clear(dev, GPIO_15 | GPIO_14);
+		mdelay(100);
+
+		/* Bring the demod and blaster out of reset */
+		mc417_gpio_set(dev, GPIO_15 | GPIO_14);
+		mdelay(100);
 
 		/* Force the TDA8295A into reset and back */
-		cx_set(GP0_IO, 0x00040004);
+		cx23885_gpio_enable(dev, GPIO_2, 1);
+		cx23885_gpio_set(dev, GPIO_2);
 		mdelay(20);
-		cx_clear(GP0_IO, 0x00000004);
+		cx23885_gpio_clear(dev, GPIO_2);
 		mdelay(20);
-		cx_set(GP0_IO, 0x00040004);
+		cx23885_gpio_set(dev, GPIO_2);
 		mdelay(20);
 		break;
 	case CX23885_BOARD_HAUPPAUGE_HVR1200:
@@ -655,6 +725,7 @@
 		break;
 	case CX23885_BOARD_LEADTEK_WINFAST_PXDVR3200_H:
 	case CX23885_BOARD_COMPRO_VIDEOMATE_E650F:
+	case CX23885_BOARD_COMPRO_VIDEOMATE_E800:
 		/* GPIO-2  xc3028 tuner reset */
 
 		/* The following GPIO's are on the internal AVCore (cx25840) */
@@ -715,19 +786,82 @@
 		cx23885_gpio_set(dev, GPIO_9);
 		break;
 	case CX23885_BOARD_MYGICA_X8506:
+	case CX23885_BOARD_MAGICPRO_PROHDTVE2:
 		/* GPIO-1 reset XC5000 */
-		/* GPIO-2 reset LGS8GL5 */
+		/* GPIO-2 reset LGS8GL5 / LGS8G75 */
 		cx_set(GP0_IO, 0x00060000);
 		cx_clear(GP0_IO, 0x00000006);
 		mdelay(100);
 		cx_set(GP0_IO, 0x00060006);
 		mdelay(100);
 		break;
+	case CX23885_BOARD_HAUPPAUGE_HVR1850:
+		/* GPIO-0 656_CLK */
+		/* GPIO-1 656_D0 */
+		/* GPIO-2 Wake# */
+		/* GPIO-3-10 cx23417 data0-7 */
+		/* GPIO-11-14 cx23417 addr0-3 */
+		/* GPIO-15-18 cx23417 READY, CS, RD, WR */
+		/* GPIO-19 IR_RX */
+		/* GPIO-20 C_IR_TX */
+		/* GPIO-21 I2S DAT */
+		/* GPIO-22 I2S WCLK */
+		/* GPIO-23 I2S BCLK */
+		/* ALT GPIO: EXP GPIO LATCH */
+
+		/* CX23417 GPIO's */
+		/* GPIO-14 S5H1411/CX24228 Reset */
+		/* GPIO-13 EEPROM write protect */
+		mc417_gpio_enable(dev, GPIO_14 | GPIO_13, 1);
+
+		/* Put the demod into reset and protect the eeprom */
+		mc417_gpio_clear(dev, GPIO_14 | GPIO_13);
+		mdelay(100);
+
+		/* Bring the demod out of reset */
+		mc417_gpio_set(dev, GPIO_14);
+		mdelay(100);
+
+		/* CX24228 GPIO */
+		/* Connected to IF / Mux */
+		break;
+    case CX23885_BOARD_MPX885:
+		/* GPIO-0 656_CLK */
+		/* GPIO-1 656_D0 */
+		/* GPIO-2 8295A Reset */
+		/* GPIO-3-10 cx23417 data0-7 */
+		/* GPIO-11-14 cx23417 addr0-3 */
+		/* GPIO-15-18 cx23417 READY, CS, RD, WR */
+		/* GPIO-19 IR_RX */
+
+		/* CX23417 GPIO's */
+		/* EIO15 Zilog Reset */
+		/* EIO14 S5H1409/CX24227 Reset */
+		mc417_gpio_enable(dev, GPIO_15 | GPIO_14, 1);
+
+		/* Put the demod into reset and protect the eeprom */
+		mc417_gpio_clear(dev, GPIO_15 | GPIO_14);
+		mdelay(100);
+
+		/* Bring the demod and blaster out of reset */
+		mc417_gpio_set(dev, GPIO_15 | GPIO_14);
+		mdelay(100);
+
+		/* Force the TDA8295A into reset and back */
+		cx23885_gpio_enable(dev, GPIO_2, 1);
+		cx23885_gpio_set(dev, GPIO_2);
+		mdelay(20);
+		cx23885_gpio_clear(dev, GPIO_2);
+		mdelay(20);
+		cx23885_gpio_set(dev, GPIO_2);
+		mdelay(20);
+		break;
 	}
 }
 
 int cx23885_ir_init(struct cx23885_dev *dev)
 {
+	int ret = 0;
 	switch (dev->board) {
 	case CX23885_BOARD_HAUPPAUGE_HVR1250:
 	case CX23885_BOARD_HAUPPAUGE_HVR1500:
@@ -741,12 +875,43 @@
 	case CX23885_BOARD_HAUPPAUGE_HVR1210:
 		/* FIXME: Implement me */
 		break;
+	case CX23885_BOARD_HAUPPAUGE_HVR1850:
+		ret = cx23888_ir_probe(dev);
+		if (ret)
+			break;
+		dev->sd_ir = cx23885_find_hw(dev, CX23885_HW_888_IR);
+		dev->pci_irqmask |= PCI_MSK_IR;
+		break;
 	case CX23885_BOARD_DVICO_FUSIONHDTV_DVB_T_DUAL_EXP:
 		request_module("ir-kbd-i2c");
 		break;
+    case CX23885_BOARD_MPX885:
+        break;
 	}
 
-	return 0;
+	return ret;
+}
+
+void cx23885_ir_fini(struct cx23885_dev *dev)
+{
+	switch (dev->board) {
+	case CX23885_BOARD_HAUPPAUGE_HVR1850:
+		dev->pci_irqmask &= ~PCI_MSK_IR;
+		cx_clear(PCI_INT_MSK, PCI_MSK_IR);
+		cx23888_ir_remove(dev);
+		dev->sd_ir = NULL;
+		break;
+	}
+}
+
+void cx23885_ir_pci_int_enable(struct cx23885_dev *dev)
+{
+	switch (dev->board) {
+	case CX23885_BOARD_HAUPPAUGE_HVR1850:
+		if (dev->sd_ir && (dev->pci_irqmask & PCI_MSK_IR))
+			cx_set(PCI_INT_MSK, PCI_MSK_IR);
+		break;
+	}
 }
 
 void cx23885_card_setup(struct cx23885_dev *dev)
@@ -778,9 +943,14 @@
 	case CX23885_BOARD_HAUPPAUGE_HVR1275:
 	case CX23885_BOARD_HAUPPAUGE_HVR1255:
 	case CX23885_BOARD_HAUPPAUGE_HVR1210:
+	case CX23885_BOARD_HAUPPAUGE_HVR1850:
 		if (dev->i2c_bus[0].i2c_rc == 0)
 			hauppauge_eeprom(dev, eeprom+0xc0);
 		break;
+    case CX23885_BOARD_MPX885:
+		if (dev->i2c_bus[0].i2c_rc == 0)
+			hauppauge_eeprom(dev, eeprom+0xc0);
+        break;
 	}
 
 	switch (dev->board) {
@@ -827,10 +997,27 @@
 		ts2->src_sel_val   = CX23885_SRC_SEL_PARALLEL_MPEG_VIDEO;
 		break;
 	case CX23885_BOARD_MYGICA_X8506:
+	case CX23885_BOARD_MAGICPRO_PROHDTVE2:
 		ts1->gen_ctrl_val  = 0x5; /* Parallel */
 		ts1->ts_clk_en_val = 0x1; /* Enable TS_CLK */
 		ts1->src_sel_val   = CX23885_SRC_SEL_PARALLEL_MPEG_VIDEO;
 		break;
+    case CX23885_BOARD_MPX885:
+		/* Defaults for VID B - Analog encoder */
+		/* DREQ_POL, SMODE, PUNC_CLK, MCLK_POL Serial bus + punc clk */
+		ts1->gen_ctrl_val    = 0x10e;
+		ts1->ts_clk_en_val   = 0x1; /* Enable TS_CLK */
+		ts1->src_sel_val     = CX23885_SRC_SEL_PARALLEL_MPEG_VIDEO;
+
+		/* APB_TSVALERR_POL (active low)*/
+		ts1->vld_misc_val    = 0x2000;
+		ts1->hw_sop_ctrl_val = (0x47 << 16 | 188 << 4 | 0xc);
+
+		/* Defaults for VID C */
+		ts2->gen_ctrl_val  = 0xc; /* Serial bus + punctured clock */
+		ts2->ts_clk_en_val = 0x1; /* Enable TS_CLK */
+		ts2->src_sel_val   = CX23885_SRC_SEL_PARALLEL_MPEG_VIDEO;
+        break;
 	case CX23885_BOARD_HAUPPAUGE_HVR1250:
 	case CX23885_BOARD_HAUPPAUGE_HVR1500:
 	case CX23885_BOARD_HAUPPAUGE_HVR1500Q:
@@ -844,6 +1031,8 @@
 	case CX23885_BOARD_HAUPPAUGE_HVR1275:
 	case CX23885_BOARD_HAUPPAUGE_HVR1255:
 	case CX23885_BOARD_HAUPPAUGE_HVR1210:
+	case CX23885_BOARD_HAUPPAUGE_HVR1850:
+	case CX23885_BOARD_COMPRO_VIDEOMATE_E800:
 	default:
 		ts2->gen_ctrl_val  = 0xc; /* Serial bus + punctured clock */
 		ts2->ts_clk_en_val = 0x1; /* Enable TS_CLK */
@@ -860,11 +1049,21 @@
 	case CX23885_BOARD_LEADTEK_WINFAST_PXDVR3200_H:
 	case CX23885_BOARD_COMPRO_VIDEOMATE_E650F:
 	case CX23885_BOARD_NETUP_DUAL_DVBS2_CI:
+	case CX23885_BOARD_COMPRO_VIDEOMATE_E800:
+	case CX23885_BOARD_HAUPPAUGE_HVR1850:
 		dev->sd_cx25840 = v4l2_i2c_new_subdev(&dev->v4l2_dev,
 				&dev->i2c_bus[2].i2c_adap,
-				"cx25840", "cx25840", 0x88 >> 1);
+				"cx25840", "cx25840", 0x88 >> 1, NULL);
 		v4l2_subdev_call(dev->sd_cx25840, core, load_fw);
 		break;
+    case CX23885_BOARD_MPX885:
+        
+		dev->sd_cx25840 = v4l2_i2c_new_subdev(&dev->v4l2_dev,
+				&dev->i2c_bus[2].i2c_adap,
+				"cx25840", "cx25840", 0x88 >> 1, NULL);
+		v4l2_subdev_call(dev->sd_cx25840, core, load_fw);
+		
+        break;
 	}
 
 	/* AUX-PLL 27MHz CLK */
diff -u cx23885/cx23885-core.c cx23885-commell/cx23885-core.c
--- cx23885/cx23885-core.c	2010-02-15 23:22:38.000000000 +0100
+++ cx23885-commell/cx23885-core.c	2009-11-11 09:36:16.000000000 +0100
@@ -28,10 +28,14 @@
 #include <linux/slab.h>
 #include <linux/interrupt.h>
 #include <linux/delay.h>
+#include "compat.h"
 #include <asm/div64.h>
 
 #include "cx23885.h"
 #include "cimax2.h"
+#include "cx23888-ir.h"
+#include "cx23885-ir.h"
+#include "cx23885-input.h"
 
 MODULE_DESCRIPTION("Driver for cx23885 based TV cards");
 MODULE_AUTHOR("Steven Toth <stoth@linuxtv.org>");
@@ -713,12 +717,26 @@
 		dev->hwrevision = 0xa1;
 		break;
 	case 0x02:
-		/* CX23885-13Z */
+		/* CX23885-13Z/14Z */
 		dev->hwrevision = 0xb0;
 		break;
 	case 0x03:
-		/* CX23888-22Z */
-		dev->hwrevision = 0xc0;
+		if (dev->pci->device == 0x8880) {
+			/* CX23888-21Z/22Z */
+			dev->hwrevision = 0xc0;
+		} else {
+			/* CX23885-14Z */
+			dev->hwrevision = 0xa4;
+		}
+		break;
+	case 0x04:
+		if (dev->pci->device == 0x8880) {
+			/* CX23888-31Z */
+			dev->hwrevision = 0xd0;
+		} else {
+			/* CX23885-15Z, CX23888-31Z */
+			dev->hwrevision = 0xa5;
+		}
 		break;
 	case 0x0e:
 		/* CX23887-15Z */
@@ -739,11 +757,29 @@
 			__func__, dev->hwrevision);
 }
 
+/* Find the first v4l2_subdev member of the group id in hw */
+struct v4l2_subdev *cx23885_find_hw(struct cx23885_dev *dev, u32 hw)
+{
+	struct v4l2_subdev *result = NULL;
+	struct v4l2_subdev *sd;
+
+	spin_lock(&dev->v4l2_dev.lock);
+	v4l2_device_for_each_subdev(sd, &dev->v4l2_dev) {
+		if (sd->grp_id == hw) {
+			result = sd;
+			break;
+		}
+	}
+	spin_unlock(&dev->v4l2_dev.lock);
+	return result;
+}
+
 static int cx23885_dev_setup(struct cx23885_dev *dev)
 {
 	int i;
 
 	mutex_init(&dev->lock);
+	mutex_init(&dev->gpio_lock);
 
 	atomic_inc(&dev->refcount);
 
@@ -756,6 +792,7 @@
 
 	/* Configure the internal memory */
 	if (dev->pci->device == 0x8880) {
+		/* Could be 887 or 888, assume a default */
 		dev->bridge = CX23885_BRIDGE_887;
 		/* Apply a sensible clock frequency for the PCIe bridge */
 		dev->clk_freq = 25000000;
@@ -868,6 +905,14 @@
 	dprintk(1, "%s() radio_type = 0x%x radio_addr = 0x%x\n",
 		__func__, dev->radio_type, dev->radio_addr);
 
+	/* The cx23417 encoder has GPIO's that need to be initialised
+	 * before DVB, so that demodulators and tuners are out of
+	 * reset before DVB uses them.
+	 */
+	if ((cx23885_boards[dev->board].portb == CX23885_MPEG_ENCODER) ||
+		(cx23885_boards[dev->board].portc == CX23885_MPEG_ENCODER))
+			cx23885_mc417_init(dev);
+
 	/* init hardware */
 	cx23885_reset(dev);
 
@@ -1250,6 +1295,7 @@
 	switch (dev->bridge) {
 	case CX23885_BRIDGE_885:
 	case CX23885_BRIDGE_887:
+	case CX23885_BRIDGE_888:
 		/* enable irqs */
 		dprintk(1, "%s() enabling TS int's and DMA\n", __func__);
 		cx_set(port->reg_ts_int_msk,  port->ts_int_msk_val);
@@ -1292,6 +1338,12 @@
 		/* clear TS1_SOP_OE and TS1_OE_HI */
 		reg = reg & ~0xa;
 		cx_write(PAD_CTRL, reg);
+#if 0
+		/*
+		 * cx_write(CLK_DELAY, cx_read(CLK_DELAY) & ~0x80000011); ????
+		 * cx_write(ALT_PIN_OUT_SEL, 0x10100045); ?? need to undo this?
+		 */
+#endif
 		cx_write(port->reg_src_sel, 0);
 		cx_write(port->reg_gen_ctrl, 8);
 
@@ -1602,7 +1654,11 @@
 	return handled;
 }
 
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2, 6, 19)
+static irqreturn_t cx23885_irq(int irq, void *dev_id, struct pt_regs *regs)
+#else
 static irqreturn_t cx23885_irq(int irq, void *dev_id)
+#endif
 {
 	struct cx23885_dev *dev = dev_id;
 	struct cx23885_tsport *ts1 = &dev->ts1;
@@ -1612,6 +1668,7 @@
 	u32 ts1_status, ts1_mask;
 	u32 ts2_status, ts2_mask;
 	int vida_count = 0, ts1_count = 0, ts2_count = 0, handled = 0;
+	bool ir_handled = false;
 
 	pci_status = cx_read(PCI_INT_STAT);
 	pci_mask = cx_read(PCI_INT_MSK);
@@ -1637,18 +1694,12 @@
 	dprintk(7, "ts2_status: 0x%08x  ts2_mask: 0x%08x count: 0x%x\n",
 		ts2_status, ts2_mask, ts2_count);
 
-	if ((pci_status & PCI_MSK_RISC_RD) ||
-	    (pci_status & PCI_MSK_RISC_WR) ||
-	    (pci_status & PCI_MSK_AL_RD) ||
-	    (pci_status & PCI_MSK_AL_WR) ||
-	    (pci_status & PCI_MSK_APB_DMA) ||
-	    (pci_status & PCI_MSK_VID_C) ||
-	    (pci_status & PCI_MSK_VID_B) ||
-	    (pci_status & PCI_MSK_VID_A) ||
-	    (pci_status & PCI_MSK_AUD_INT) ||
-	    (pci_status & PCI_MSK_AUD_EXT) ||
-	    (pci_status & PCI_MSK_GPIO0) ||
-	    (pci_status & PCI_MSK_GPIO1)) {
+	if (pci_status & (PCI_MSK_RISC_RD | PCI_MSK_RISC_WR |
+			  PCI_MSK_AL_RD   | PCI_MSK_AL_WR   | PCI_MSK_APB_DMA |
+			  PCI_MSK_VID_C   | PCI_MSK_VID_B   | PCI_MSK_VID_A   |
+			  PCI_MSK_AUD_INT | PCI_MSK_AUD_EXT |
+			  PCI_MSK_GPIO0   | PCI_MSK_GPIO1   |
+			  PCI_MSK_IR)) {
 
 		if (pci_status & PCI_MSK_RISC_RD)
 			dprintk(7, " (PCI_MSK_RISC_RD   0x%08x)\n",
@@ -1697,6 +1748,10 @@
 		if (pci_status & PCI_MSK_GPIO1)
 			dprintk(7, " (PCI_MSK_GPIO1     0x%08x)\n",
 				PCI_MSK_GPIO1);
+
+		if (pci_status & PCI_MSK_IR)
+			dprintk(7, " (PCI_MSK_IR        0x%08x)\n",
+				PCI_MSK_IR);
 	}
 
 	if (cx23885_boards[dev->board].cimax > 0 &&
@@ -1727,12 +1782,55 @@
 	if (vida_status)
 		handled += cx23885_video_irq(dev, vida_status);
 
+	if (pci_status & PCI_MSK_IR) {
+		v4l2_subdev_call(dev->sd_ir, ir, interrupt_service_routine,
+				 pci_status, &ir_handled);
+		if (ir_handled)
+			handled++;
+	}
+
 	if (handled)
 		cx_write(PCI_INT_STAT, pci_status);
 out:
 	return IRQ_RETVAL(handled);
 }
 
+static void cx23885_v4l2_dev_notify(struct v4l2_subdev *sd,
+				    unsigned int notification, void *arg)
+{
+	struct cx23885_dev *dev;
+
+	if (sd == NULL)
+		return;
+
+	dev = to_cx23885(sd->v4l2_dev);
+
+	switch (notification) {
+	case V4L2_SUBDEV_IR_RX_NOTIFY: /* Called in an IRQ context */
+		if (sd == dev->sd_ir)
+			cx23885_ir_rx_v4l2_dev_notify(sd, *(u32 *)arg);
+		break;
+	case V4L2_SUBDEV_IR_TX_NOTIFY: /* Called in an IRQ context */
+		if (sd == dev->sd_ir)
+			cx23885_ir_tx_v4l2_dev_notify(sd, *(u32 *)arg);
+		break;
+	}
+}
+
+static void cx23885_v4l2_dev_notify_init(struct cx23885_dev *dev)
+{
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2, 6, 20)
+	INIT_WORK(&dev->ir_rx_work, cx23885_ir_rx_work_handler);
+	INIT_WORK(&dev->ir_tx_work, cx23885_ir_tx_work_handler);
+#else
+	INIT_WORK(&dev->ir_rx_work, cx23885_ir_rx_work_handler,
+		  &dev->ir_rx_work);
+	INIT_WORK(&dev->ir_tx_work, cx23885_ir_tx_work_handler,
+		  &dev->ir_tx_work);
+#endif
+	dev->v4l2_dev.notify = cx23885_v4l2_dev_notify;
+}
+
 static inline int encoder_on_portb(struct cx23885_dev *dev)
 {
 	return cx23885_boards[dev->board].portb == CX23885_MPEG_ENCODER;
@@ -1829,6 +1927,9 @@
 	if (err < 0)
 		goto fail_free;
 
+	/* Prepare to handle notifications from subdevices */
+	cx23885_v4l2_dev_notify_init(dev);
+
 	/* pci init */
 	dev->pci = pci_dev;
 	if (pci_enable_device(pci_dev)) {
@@ -1871,6 +1972,14 @@
 		break;
 	}
 
+	/*
+	 * The CX2388[58] IR controller can start firing interrupts when
+	 * enabled, so these have to take place after the cx23885_irq() handler
+	 * is hooked up by the call to request_irq() above.
+	 */
+	cx23885_ir_pci_int_enable(dev);
+	cx23885_input_init(dev);
+
 	return 0;
 
 fail_irq:
@@ -1887,6 +1996,9 @@
 	struct v4l2_device *v4l2_dev = pci_get_drvdata(pci_dev);
 	struct cx23885_dev *dev = to_cx23885(v4l2_dev);
 
+	cx23885_input_fini(dev);
+	cx23885_ir_fini(dev);
+
 	cx23885_shutdown(dev);
 
 	pci_disable_device(pci_dev);
diff -u cx23885/cx23885-dvb.c cx23885-commell/cx23885-dvb.c
--- cx23885/cx23885-dvb.c	2010-02-15 23:22:38.000000000 +0100
+++ cx23885-commell/cx23885-dvb.c	2009-11-11 09:36:16.000000000 +0100
@@ -26,6 +26,7 @@
 #include <linux/kthread.h>
 #include <linux/file.h>
 #include <linux/suspend.h>
+#include "compat.h"
 
 #include "cx23885.h"
 #include <media/v4l2-common.h>
@@ -255,15 +256,18 @@
 static struct tda18271_config hauppauge_tda18271_config = {
 	.std_map = &hauppauge_tda18271_std_map,
 	.gate    = TDA18271_GATE_ANALOG,
+	.output_opt = TDA18271_OUTPUT_LT_OFF,
 };
 
 static struct tda18271_config hauppauge_hvr1200_tuner_config = {
 	.std_map = &hauppauge_hvr1200_tda18271_std_map,
 	.gate    = TDA18271_GATE_ANALOG,
+	.output_opt = TDA18271_OUTPUT_LT_OFF,
 };
 
 static struct tda18271_config hauppauge_hvr1210_tuner_config = {
 	.gate    = TDA18271_GATE_DIGITAL,
+	.output_opt = TDA18271_OUTPUT_LT_OFF,
 };
 
 static struct tda18271_std_map hauppauge_hvr127x_std_map = {
@@ -275,6 +279,7 @@
 
 static struct tda18271_config hauppauge_hvr127x_config = {
 	.std_map = &hauppauge_hvr127x_std_map,
+	.output_opt = TDA18271_OUTPUT_LT_OFF,
 };
 
 static struct lgdt3305_config hauppauge_lgdt3305_config = {
@@ -396,7 +401,7 @@
 
 static struct stv0900_config netup_stv0900_config = {
 	.demod_address = 0x68,
-	.xtal = 27000000,
+	.xtal = 8000000,
 	.clkmode = 3,/* 0-CLKI, 2-XTALI, else AUTO */
 	.diseqc_mode = 2,/* 2/3 PWM */
 	.ts_config_regs = stv0900_ts_regs,
@@ -408,14 +413,14 @@
 
 static struct stv6110_config netup_stv6110_tunerconfig_a = {
 	.i2c_address = 0x60,
-	.mclk = 27000000,
-	.iq_wiring = 0,
+	.mclk = 16000000,
+	.clk_div = 1,
 };
 
 static struct stv6110_config netup_stv6110_tunerconfig_b = {
 	.i2c_address = 0x63,
-	.mclk = 27000000,
-	.iq_wiring = 1,
+	.mclk = 16000000,
+	.clk_div = 1,
 };
 
 static int tbs_set_voltage(struct dvb_frontend *fe, fe_sec_voltage_t voltage)
@@ -483,10 +488,54 @@
 		}
 		break;
 	}
-	return (port->set_frontend_save) ?
-		port->set_frontend_save(fe, param) : -ENODEV;
+	return 0;
 }
 
+static int cx23885_dvb_fe_ioctl_override(struct dvb_frontend *fe,
+					 unsigned int cmd, void *parg,
+					 unsigned int stage)
+{
+	int err = 0;
+
+	switch (stage) {
+	case DVB_FE_IOCTL_PRE:
+
+		switch (cmd) {
+		case FE_SET_FRONTEND:
+			err = cx23885_dvb_set_frontend(fe,
+				(struct dvb_frontend_parameters *) parg);
+			break;
+		}
+		break;
+
+	case DVB_FE_IOCTL_POST:
+		/* no post-ioctl handling required */
+		break;
+	}
+	return err;
+};
+
+
+static struct lgs8gxx_config magicpro_prohdtve2_lgs8g75_config = {
+	.prod = LGS8GXX_PROD_LGS8G75,
+	.demod_address = 0x19,
+	.serial_ts = 0,
+	.ts_clk_pol = 1,
+	.ts_clk_gated = 1,
+	.if_clk_freq = 30400, /* 30.4 MHz */
+	.if_freq = 6500, /* 6.50 MHz */
+	.if_neg_center = 1,
+	.ext_adc = 0,
+	.adc_signed = 1,
+	.adc_vpp = 2, /* 1.6 Vpp */
+	.if_neg_edge = 1,
+};
+
+static struct xc5000_config magicpro_prohdtve2_xc5000_config = {
+	.i2c_address = 0x61,
+	.if_khz = 6500,
+};
+
 static int dvb_register(struct cx23885_tsport *port)
 {
 	struct cx23885_dev *dev = port->dev;
@@ -526,12 +575,6 @@
 				   0x60, &dev->i2c_bus[1].i2c_adap,
 				   &hauppauge_hvr127x_config);
 		}
-
-		/* FIXME: temporary hack */
-		/* define bridge override to set_frontend */
-		port->set_frontend_save = fe0->dvb.frontend->ops.set_frontend;
-		fe0->dvb.frontend->ops.set_frontend = cx23885_dvb_set_frontend;
-
 		break;
 	case CX23885_BOARD_HAUPPAUGE_HVR1255:
 		i2c_bus = &dev->i2c_bus[0];
@@ -574,6 +617,36 @@
 			break;
 		}
 		break;
+    case CX23885_BOARD_MPX885:
+		i2c_bus = &dev->i2c_bus[0];
+		switch (alt_tuner) {
+		case 1:
+			fe0->dvb.frontend =
+				dvb_attach(s5h1409_attach,
+					   &hauppauge_ezqam_config,
+					   &i2c_bus->i2c_adap);
+			if (fe0->dvb.frontend != NULL) {
+				dvb_attach(tda829x_attach, fe0->dvb.frontend,
+					   &dev->i2c_bus[1].i2c_adap, 0x42,
+					   &tda829x_no_probe);
+				dvb_attach(tda18271_attach, fe0->dvb.frontend,
+					   0x60, &dev->i2c_bus[1].i2c_adap,
+					   &hauppauge_tda18271_config);
+			}
+			break;
+		case 0:
+		default:
+			fe0->dvb.frontend =
+				dvb_attach(s5h1409_attach,
+					   &hauppauge_generic_config,
+					   &i2c_bus->i2c_adap);
+			if (fe0->dvb.frontend != NULL)
+				dvb_attach(mt2131_attach, fe0->dvb.frontend,
+					   &i2c_bus->i2c_adap,
+					   &hauppauge_generic_tunerconfig, 0);
+			break;
+		}
+        break;
 	case CX23885_BOARD_HAUPPAUGE_HVR1800lp:
 		i2c_bus = &dev->i2c_bus[0];
 		fe0->dvb.frontend = dvb_attach(s5h1409_attach,
@@ -723,6 +796,7 @@
 	}
 	case CX23885_BOARD_LEADTEK_WINFAST_PXDVR3200_H:
 	case CX23885_BOARD_COMPRO_VIDEOMATE_E650F:
+	case CX23885_BOARD_COMPRO_VIDEOMATE_E800:
 		i2c_bus = &dev->i2c_bus[0];
 
 		fe0->dvb.frontend = dvb_attach(zl10353_attach,
@@ -833,6 +907,30 @@
 				&mygica_x8506_xc5000_config);
 		}
 		break;
+	case CX23885_BOARD_MAGICPRO_PROHDTVE2:
+		i2c_bus = &dev->i2c_bus[0];
+		i2c_bus2 = &dev->i2c_bus[1];
+		fe0->dvb.frontend = dvb_attach(lgs8gxx_attach,
+			&magicpro_prohdtve2_lgs8g75_config,
+			&i2c_bus->i2c_adap);
+		if (fe0->dvb.frontend != NULL) {
+			dvb_attach(xc5000_attach,
+				fe0->dvb.frontend,
+				&i2c_bus2->i2c_adap,
+				&magicpro_prohdtve2_xc5000_config);
+		}
+		break;
+	case CX23885_BOARD_HAUPPAUGE_HVR1850:
+		i2c_bus = &dev->i2c_bus[0];
+		fe0->dvb.frontend = dvb_attach(s5h1411_attach,
+			&hcw_s5h1411_config,
+			&i2c_bus->i2c_adap);
+		if (fe0->dvb.frontend != NULL)
+			dvb_attach(tda18271_attach, fe0->dvb.frontend,
+				0x60, &dev->i2c_bus[0].i2c_adap,
+				&hauppauge_tda18271_config);
+		break;
+
 	default:
 		printk(KERN_INFO "%s: The frontend of your DVB/ATSC card "
 			" isn't supported yet\n",
@@ -855,7 +953,8 @@
 
 	/* register everything */
 	ret = videobuf_dvb_register_bus(&port->frontends, THIS_MODULE, port,
-		&dev->pci->dev, adapter_nr, 0);
+					&dev->pci->dev, adapter_nr, 0,
+					cx23885_dvb_fe_ioctl_override);
 
 	/* init CI & MAC */
 	switch (dev->board) {
diff -u cx23885/cx23885.h cx23885-commell/cx23885.h
--- cx23885/cx23885.h	2010-02-15 23:22:38.000000000 +0100
+++ cx23885-commell/cx23885.h	2009-11-11 09:36:20.000000000 +0100
@@ -29,6 +29,7 @@
 #include <media/tveeprom.h>
 #include <media/videobuf-dma-sg.h>
 #include <media/videobuf-dvb.h>
+#include "compat.h"
 
 #include "btcx-risc.h"
 #include "cx23885-reg.h"
@@ -76,6 +77,10 @@
 #define CX23885_BOARD_HAUPPAUGE_HVR1255        20
 #define CX23885_BOARD_HAUPPAUGE_HVR1210        21
 #define CX23885_BOARD_MYGICA_X8506             22
+#define CX23885_BOARD_MAGICPRO_PROHDTVE2       23
+#define CX23885_BOARD_HAUPPAUGE_HVR1850        24
+#define CX23885_BOARD_COMPRO_VIDEOMATE_E800    25
+#define CX23885_BOARD_MPX885                26
 
 #define GPIO_0 0x00000001
 #define GPIO_1 0x00000002
@@ -87,6 +92,12 @@
 #define GPIO_7 0x00000080
 #define GPIO_8 0x00000100
 #define GPIO_9 0x00000200
+#define GPIO_10 0x00000400
+#define GPIO_11 0x00000800
+#define GPIO_12 0x00001000
+#define GPIO_13 0x00002000
+#define GPIO_14 0x00004000
+#define GPIO_15 0x00008000
 
 /* Currently unsupported by the driver: PAL/H, NTSC/Kr, SECAM B/G/H/LC */
 #define CX23885_NORMS (\
@@ -288,10 +299,6 @@
 	/* Allow a single tsport to have multiple frontends */
 	u32                        num_frontends;
 	void                       *port_priv;
-
-	/* FIXME: temporary hack */
-	int (*set_frontend_save) (struct dvb_frontend *,
-				  struct dvb_frontend_parameters *);
 };
 
 struct cx23885_dev {
@@ -317,6 +324,7 @@
 
 	int                        nr;
 	struct mutex               lock;
+	struct mutex               gpio_lock;
 
 	/* board details */
 	unsigned int               board;
@@ -331,6 +339,7 @@
 		CX23885_BRIDGE_UNDEFINED = 0,
 		CX23885_BRIDGE_885 = 885,
 		CX23885_BRIDGE_887 = 887,
+		CX23885_BRIDGE_888 = 888,
 	} bridge;
 
 	/* Analog video */
@@ -345,6 +354,16 @@
 	unsigned int               has_radio;
 	struct v4l2_subdev 	   *sd_cx25840;
 
+	/* Infrared */
+	struct v4l2_subdev         *sd_ir;
+	struct work_struct	   ir_rx_work;
+	unsigned long		   ir_rx_notifications;
+	struct work_struct	   ir_tx_work;
+	unsigned long		   ir_tx_notifications;
+
+	struct card_ir		   *ir_input;
+	atomic_t		   ir_input_stopping;
+
 	/* V4l */
 	u32                        freq;
 	struct video_device        *video_dev;
@@ -372,6 +391,13 @@
 #define call_all(dev, o, f, args...) \
 	v4l2_device_call_all(&dev->v4l2_dev, 0, o, f, ##args)
 
+#define CX23885_HW_888_IR (1 << 0)
+
+#define call_hw(dev, grpid, o, f, args...) \
+	v4l2_device_call_all(&dev->v4l2_dev, grpid, o, f, ##args)
+
+extern struct v4l2_subdev *cx23885_find_hw(struct cx23885_dev *dev, u32 hw);
+
 extern struct list_head cx23885_devlist;
 
 #define SRAM_CH01  0 /* Video A */
@@ -395,7 +421,7 @@
 	u32  cmds_start;
 	u32  ctrl_start;
 	u32  cdt;
-	u32  fifo_start;;
+	u32  fifo_start;
 	u32  fifo_size;
 	u32  ptr1_reg;
 	u32  ptr2_reg;
@@ -460,6 +486,8 @@
 	int command, int arg);
 extern void cx23885_card_list(struct cx23885_dev *dev);
 extern int  cx23885_ir_init(struct cx23885_dev *dev);
+extern void cx23885_ir_pci_int_enable(struct cx23885_dev *dev);
+extern void cx23885_ir_fini(struct cx23885_dev *dev);
 extern void cx23885_gpio_setup(struct cx23885_dev *dev);
 extern void cx23885_card_setup(struct cx23885_dev *dev);
 extern void cx23885_card_setup_pre_i2c(struct cx23885_dev *dev);
@@ -504,6 +532,13 @@
 extern void cx23885_mc417_init(struct cx23885_dev *dev);
 extern int mc417_memory_read(struct cx23885_dev *dev, u32 address, u32 *value);
 extern int mc417_memory_write(struct cx23885_dev *dev, u32 address, u32 value);
+extern int mc417_register_read(struct cx23885_dev *dev,
+				u16 address, u32 *value);
+extern int mc417_register_write(struct cx23885_dev *dev,
+				u16 address, u32 value);
+extern void mc417_gpio_set(struct cx23885_dev *dev, u32 mask);
+extern void mc417_gpio_clear(struct cx23885_dev *dev, u32 mask);
+extern void mc417_gpio_enable(struct cx23885_dev *dev, u32 mask, int asoutput);
 
 
 /* ----------------------------------------------------------- */
diff -u cx23885/cx23885-i2c.c cx23885-commell/cx23885-i2c.c
--- cx23885/cx23885-i2c.c	2010-02-15 23:22:38.000000000 +0100
+++ cx23885-commell/cx23885-i2c.c	2009-11-11 09:36:16.000000000 +0100
@@ -25,6 +25,7 @@
 #include <linux/delay.h>
 #include <asm/io.h>
 
+#include "compat.h"
 #include "cx23885.h"
 
 #include <media/v4l2-common.h>
@@ -276,6 +277,9 @@
 static struct i2c_algorithm cx23885_i2c_algo_template = {
 	.master_xfer	= i2c_xfer,
 	.functionality	= cx23885_functionality,
+#ifdef NEED_ALGO_CONTROL
+	.algo_control = dummy_algo_control,
+#endif
 };
 
 /* ----------------------------------------------------------------------- */
@@ -283,8 +287,13 @@
 static struct i2c_adapter cx23885_i2c_adap_template = {
 	.name              = "cx23885",
 	.owner             = THIS_MODULE,
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2, 6, 31)
 	.id                = I2C_HW_B_CX23885,
+#endif
 	.algo              = &cx23885_i2c_algo_template,
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2, 6, 26)
+	.class             = I2C_CLASS_TV_ANALOG,
+#endif
 };
 
 static struct i2c_client cx23885_i2c_client_template = {
@@ -357,6 +366,7 @@
 		printk(KERN_WARNING "%s: i2c bus %d register FAILED\n",
 			dev->name, bus->nr);
 
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2, 6, 30)
 	/* Instantiate the IR receiver device, if present */
 	if (0 == bus->i2c_rc) {
 		struct i2c_board_info info;
@@ -369,6 +379,7 @@
 		i2c_new_probed_device(&bus->i2c_adap, &info, addr_list);
 	}
 
+#endif
 	return bus->i2c_rc;
 }
 
Nur in cx23885-commell: cx23885-input.c.
Nur in cx23885-commell: cx23885-input.h.
Nur in cx23885-commell: cx23885-ioctl.c.
Nur in cx23885-commell: cx23885-ioctl.h.
Nur in cx23885-commell: cx23885-ir.c.
Nur in cx23885-commell: cx23885-ir.h.
Nur in cx23885: cx23885.mod.c.
diff -u cx23885/cx23885-reg.h cx23885-commell/cx23885-reg.h
--- cx23885/cx23885-reg.h	2010-02-15 23:22:38.000000000 +0100
+++ cx23885-commell/cx23885-reg.h	2009-11-11 09:36:20.000000000 +0100
@@ -212,8 +212,9 @@
 
 #define DEV_CNTRL2	0x00040000
 
-#define PCI_MSK_GPIO1   (1 << 24)
-#define PCI_MSK_GPIO0   (1 << 23)
+#define PCI_MSK_IR        (1 << 28)
+#define PCI_MSK_GPIO1     (1 << 24)
+#define PCI_MSK_GPIO0     (1 << 23)
 #define PCI_MSK_APB_DMA   (1 << 12)
 #define PCI_MSK_AL_WR     (1 << 11)
 #define PCI_MSK_AL_RD     (1 << 10)
diff -u cx23885/cx23885-vbi.c cx23885-commell/cx23885-vbi.c
--- cx23885/cx23885-vbi.c	2010-02-15 23:22:38.000000000 +0100
+++ cx23885-commell/cx23885-vbi.c	2009-11-11 09:36:16.000000000 +0100
@@ -25,6 +25,7 @@
 #include <linux/init.h>
 #include <linux/slab.h>
 
+#include "compat.h"
 #include "cx23885.h"
 
 static unsigned int vbibufs = 4;
@@ -85,6 +86,19 @@
 	return 0;
 }
 
+#if 0
+/* not (yet) used */
+static int cx23885_stop_vbi_dma(struct cx23885_dev *dev)
+{
+	/* stop dma */
+	cx_clear(VID_A_DMA_CTL, 0x00000022);
+
+	/* disable irqs */
+	cx_clear(PCI_INT_MSK, 0x000001);
+	cx_clear(VID_A_INT_MSK, 0x00000022);
+	return 0;
+}
+#endif
 
 static int cx23885_restart_vbi_queue(struct cx23885_dev    *dev,
 			     struct cx23885_dmaqueue *q)
diff -u cx23885/cx23885-video.c cx23885-commell/cx23885-video.c
--- cx23885/cx23885-video.c	2010-02-15 23:22:38.000000000 +0100
+++ cx23885-commell/cx23885-video.c	2009-11-11 09:36:16.000000000 +0100
@@ -29,12 +29,14 @@
 #include <linux/smp_lock.h>
 #include <linux/interrupt.h>
 #include <linux/delay.h>
+#include "compat.h"
 #include <linux/kthread.h>
 #include <asm/div64.h>
 
 #include "cx23885.h"
 #include <media/v4l2-common.h>
 #include <media/v4l2-ioctl.h>
+#include "cx23885-ioctl.h"
 
 MODULE_DESCRIPTION("v4l2 driver module for cx23885 based TV cards");
 MODULE_AUTHOR("Steven Toth <stoth@linuxtv.org>");
@@ -80,51 +82,82 @@
 	{
 		.name     = "8 bpp, gray",
 		.fourcc   = V4L2_PIX_FMT_GREY,
+#if 0
+		.cxformat = ColorFormatY8,
+#endif
 		.depth    = 8,
 		.flags    = FORMAT_FLAGS_PACKED,
 	}, {
 		.name     = "15 bpp RGB, le",
 		.fourcc   = V4L2_PIX_FMT_RGB555,
+#if 0
+		.cxformat = ColorFormatRGB15,
+#endif
 		.depth    = 16,
 		.flags    = FORMAT_FLAGS_PACKED,
 	}, {
 		.name     = "15 bpp RGB, be",
 		.fourcc   = V4L2_PIX_FMT_RGB555X,
+#if 0
+		.cxformat = ColorFormatRGB15 | ColorFormatBSWAP,
+#endif
 		.depth    = 16,
 		.flags    = FORMAT_FLAGS_PACKED,
 	}, {
 		.name     = "16 bpp RGB, le",
 		.fourcc   = V4L2_PIX_FMT_RGB565,
+#if 0
+		.cxformat = ColorFormatRGB16,
+#endif
 		.depth    = 16,
 		.flags    = FORMAT_FLAGS_PACKED,
 	}, {
 		.name     = "16 bpp RGB, be",
 		.fourcc   = V4L2_PIX_FMT_RGB565X,
+#if 0
+		.cxformat = ColorFormatRGB16 | ColorFormatBSWAP,
+#endif
 		.depth    = 16,
 		.flags    = FORMAT_FLAGS_PACKED,
 	}, {
 		.name     = "24 bpp RGB, le",
 		.fourcc   = V4L2_PIX_FMT_BGR24,
+#if 0
+		.cxformat = ColorFormatRGB24,
+#endif
 		.depth    = 24,
 		.flags    = FORMAT_FLAGS_PACKED,
 	}, {
 		.name     = "32 bpp RGB, le",
 		.fourcc   = V4L2_PIX_FMT_BGR32,
+#if 0
+		.cxformat = ColorFormatRGB32,
+#endif
 		.depth    = 32,
 		.flags    = FORMAT_FLAGS_PACKED,
 	}, {
 		.name     = "32 bpp RGB, be",
 		.fourcc   = V4L2_PIX_FMT_RGB32,
+#if 0
+		.cxformat = ColorFormatRGB32 | ColorFormatBSWAP |
+			ColorFormatWSWAP,
+#endif
 		.depth    = 32,
 		.flags    = FORMAT_FLAGS_PACKED,
 	}, {
 		.name     = "4:2:2, packed, YUYV",
 		.fourcc   = V4L2_PIX_FMT_YUYV,
+#if 0
+		.cxformat = ColorFormatYUY2,
+#endif
 		.depth    = 16,
 		.flags    = FORMAT_FLAGS_PACKED,
 	}, {
 		.name     = "4:2:2, packed, UYVY",
 		.fourcc   = V4L2_PIX_FMT_UYVY,
+#if 0
+		.cxformat = ColorFormatYUY2 | ColorFormatBSWAP,
+#endif
 		.depth    = 16,
 		.flags    = FORMAT_FLAGS_PACKED,
 	},
@@ -248,6 +281,9 @@
 	V4L2_CID_SATURATION,
 	V4L2_CID_HUE,
 	V4L2_CID_AUDIO_VOLUME,
+#if 0
+	V4L2_CID_AUDIO_BALANCE,
+#endif
 	V4L2_CID_AUDIO_MUTE,
 	0
 };
@@ -404,6 +440,10 @@
 	/* Tell the internal A/V decoder */
 	v4l2_subdev_call(dev->sd_cx25840, video, s_routing,
 			INPUT(input)->vmux, 0, 0);
+#if 0
+	/* Let the AVCore default */
+	v4l2_subdev_call(dev->sd_cx25840, audio, s_routing, 0, 0, 0);
+#endif
 
 	return 0;
 }
@@ -442,6 +482,22 @@
 	return 0;
 }
 
+#if 0
+#ifdef CONFIG_PM
+static int cx23885_stop_video_dma(struct cx23885_dev *dev)
+{
+	dprintk(1, "%s()\n", __func__);
+	/* stop dma */
+	cx_clear(VID_A_DMA_CTL, 0x11);
+
+	/* disable irqs */
+	cx_clear(PCI_INT_MSK, 0x000001);
+	cx_clear(VID_A_INT_MSK, 0x000011);
+
+	return 0;
+}
+#endif
+#endif
 
 static int cx23885_restart_video_queue(struct cx23885_dev *dev,
 			       struct cx23885_dmaqueue *q)
@@ -765,6 +821,20 @@
 
 	dprintk(1, "post videobuf_queue_init()\n");
 
+#if 0
+	if (fh->radio) {
+		int board = dev->board;
+		dprintk(1, "video_open: setting radio device\n");
+		cx_write(MO_GP3_IO, cx88_boards[board].radio.gpio3);
+		cx_write(MO_GP0_IO, cx88_boards[board].radio.gpio0);
+		cx_write(MO_GP1_IO, cx88_boards[board].radio.gpio1);
+		cx_write(MO_GP2_IO, cx88_boards[board].radio.gpio2);
+		dev->tvaudio = WW_FM;
+		cx23885_set_tvaudio(dev);
+		cx23885_set_stereo(dev, V4L2_TUNER_MODE_STEREO, 1);
+		call_all(dev, tuner, s_radio);
+	}
+#endif
 	unlock_kernel();
 
 	return 0;
@@ -860,6 +930,9 @@
 	}
 
 	videobuf_mmap_free(&fh->vidq);
+#if 0
+	videobuf_mmap_free(&fh->vbiq);
+#endif
 	file->private_data = NULL;
 	kfree(fh);
 
@@ -867,6 +940,9 @@
 	 * we want to use the mpeg encoder in another session to capture
 	 * tuner video. Closing this will result in no video to the encoder.
 	 */
+#if 0
+	call_all(dev, tuner, s_standby);
+#endif
 
 	return 0;
 }
@@ -894,6 +970,9 @@
 {
 	dprintk(1, "%s() calling cx25840(VIDIOC_S_CTRL)"
 		" (disabled - no action)\n", __func__);
+#if 1
+	call_all(dev, core, s_ctrl, ctl);
+#endif
 	return 0;
 }
 
@@ -1007,6 +1086,9 @@
 	sprintf(cap->bus_info, "PCIe:%s", pci_name(dev->pci));
 	cap->version = CX23885_VERSION_CODE;
 	cap->capabilities =
+#if 0
+		V4L2_CAP_VIDEO_OVERLAY |
+#endif
 		V4L2_CAP_VIDEO_CAPTURE |
 		V4L2_CAP_READWRITE     |
 		V4L2_CAP_STREAMING     |
@@ -1243,6 +1325,9 @@
 	t->type       = V4L2_TUNER_ANALOG_TV;
 	t->capability = V4L2_TUNER_CAP_NORM;
 	t->rangehigh  = 0xffffffffUL;
+#if 0
+	cx23885_get_stereo(dev, t);
+#endif
 	t->signal = 0xffff ; /* LOCKED */
 	return 0;
 }
@@ -1256,6 +1341,9 @@
 		return -EINVAL;
 	if (0 != t->index)
 		return -EINVAL;
+#if 0
+	cx23885_set_stereo(dev, t->audmode, 1);
+#endif
 	return 0;
 }
 
@@ -1312,34 +1400,105 @@
 		cx23885_set_freq(dev, f);
 }
 
-#ifdef CONFIG_VIDEO_ADV_DEBUG
-static int vidioc_g_register(struct file *file, void *fh,
-				struct v4l2_dbg_register *reg)
+#if 0
+/* ----------------------------------------------------------- */
+/* RADIO ESPECIFIC IOCTLS                                      */
+/* ----------------------------------------------------------- */
+
+static int radio_querycap(struct file *file, void  *priv,
+					struct v4l2_capability *cap)
+{
+	struct cx23885_dev *dev = ((struct cx23885_fh *)priv)->dev;
+
+	strcpy(cap->driver, "cx23885");
+	strlcpy(cap->card, cx23885_boards[dev->board].name,
+		sizeof(cap->card));
+	sprintf(cap->bus_info, "PCIe:%s", pci_name(dev->pci));
+	cap->version = CX23885_VERSION_CODE;
+	cap->capabilities = V4L2_CAP_TUNER;
+	return 0;
+}
+
+static int radio_g_tuner(struct file *file, void *priv,
+				struct v4l2_tuner *t)
 {
-	struct cx23885_dev *dev = ((struct cx23885_fh *)fh)->dev;
+	struct cx23885_dev *dev = ((struct cx23885_fh *)priv)->dev;
+
+	if (unlikely(t->index > 0))
+		return -EINVAL;
+
+	strcpy(t->name, "Radio");
+	t->type = V4L2_TUNER_RADIO;
+
+	call_all(dev, tuner, g_tuner, t);
+	return 0;
+}
 
-	if (!v4l2_chip_match_host(&reg->match))
+static int radio_enum_input(struct file *file, void *priv,
+				struct v4l2_input *i)
+{
+	if (i->index != 0)
 		return -EINVAL;
+	strcpy(i->name, "Radio");
+	i->type = V4L2_INPUT_TYPE_TUNER;
+
+	return 0;
+}
 
-	call_all(dev, core, g_register, reg);
+static int radio_g_audio(struct file *file, void *priv, struct v4l2_audio *a)
+{
+	if (unlikely(a->index))
+		return -EINVAL;
 
+	memset(a, 0, sizeof(*a));
+	strcpy(a->name, "Radio");
 	return 0;
 }
 
-static int vidioc_s_register(struct file *file, void *fh,
-				struct v4l2_dbg_register *reg)
+/* FIXME: Should add a standard for radio */
+
+static int radio_s_tuner(struct file *file, void *priv,
+				struct v4l2_tuner *t)
 {
-	struct cx23885_dev *dev = ((struct cx23885_fh *)fh)->dev;
+	struct cx23885_dev *dev = ((struct cx23885_fh *)priv)->dev;
 
-	if (!v4l2_chip_match_host(&reg->match))
+	if (0 != t->index)
 		return -EINVAL;
 
-	call_all(dev, core, s_register, reg);
+	call_all(dev, tuner, s_tuner, t);
 
 	return 0;
 }
-#endif
 
+static int radio_s_audio(struct file *file, void *fh,
+			  struct v4l2_audio *a)
+{
+	return 0;
+}
+
+static int radio_s_input(struct file *file, void *fh, unsigned int i)
+{
+	return 0;
+}
+
+static int radio_queryctrl(struct file *file, void *priv,
+			    struct v4l2_queryctrl *c)
+{
+	int i;
+
+	if (c->id <  V4L2_CID_BASE ||
+		c->id >= V4L2_CID_LASTP1)
+		return -EINVAL;
+	if (c->id == V4L2_CID_AUDIO_MUTE) {
+		for (i = 0; i < CX23885_CTLS; i++)
+			if (cx23885_ctls[i].v.id == c->id)
+				break;
+		*c = cx23885_ctls[i].v;
+	} else
+		*c = no_ctl;
+	return 0;
+}
+#endif
 /* ----------------------------------------------------------- */
 
 static void cx23885_vid_timeout(unsigned long data)
@@ -1395,6 +1554,16 @@
 		spin_unlock(&dev->slock);
 		handled++;
 	}
+#if 0
+	/* risc1 vbi */
+	if (status & 0x08) {
+		spin_lock(&dev->slock);
+		count = cx_read(MO_VBI_GPCNT);
+		cx88_wakeup(core, &dev->vbiq, count);
+		spin_unlock(&dev->slock);
+		handled++;
+	}
+#endif
 	/* risc2 y */
 	if (status & 0x10) {
 		dprintk(2, "stopper video\n");
@@ -1403,6 +1572,16 @@
 		spin_unlock(&dev->slock);
 		handled++;
 	}
+#if 0
+	/* risc2 vbi */
+	if (status & 0x80) {
+		dprintk(2, "stopper vbi\n");
+		spin_lock(&dev->slock);
+		cx8800_restart_vbi_queue(dev, &dev->vbiq);
+		spin_unlock(&dev->slock);
+		handled++;
+	}
+#endif
 
 	return handled;
 }
@@ -1449,9 +1628,10 @@
 	.vidioc_s_tuner       = vidioc_s_tuner,
 	.vidioc_g_frequency   = vidioc_g_frequency,
 	.vidioc_s_frequency   = vidioc_s_frequency,
+	.vidioc_g_chip_ident  = cx23885_g_chip_ident,
 #ifdef CONFIG_VIDEO_ADV_DEBUG
-	.vidioc_g_register    = vidioc_g_register,
-	.vidioc_s_register    = vidioc_s_register,
+	.vidioc_g_register    = cx23885_g_register,
+	.vidioc_s_register    = cx23885_s_register,
 #endif
 };
 
@@ -1472,12 +1652,52 @@
 	.ioctl         = video_ioctl2,
 };
 
+#if 0
+static const struct v4l2_ioctl_ops radio_ioctl_ops = {
+	.vidioc_querycap      = radio_querycap,
+	.vidioc_g_tuner       = radio_g_tuner,
+	.vidioc_enum_input    = radio_enum_input,
+	.vidioc_g_audio       = radio_g_audio,
+	.vidioc_s_tuner       = radio_s_tuner,
+	.vidioc_s_audio       = radio_s_audio,
+	.vidioc_s_input       = radio_s_input,
+	.vidioc_queryctrl     = radio_queryctrl,
+	.vidioc_g_ctrl        = vidioc_g_ctrl,
+	.vidioc_s_ctrl        = vidioc_s_ctrl,
+	.vidioc_g_frequency   = vidioc_g_frequency,
+	.vidioc_s_frequency   = vidioc_s_frequency,
+};
+
+static struct video_device cx23885_radio_template = {
+	.name                 = "cx23885-radio",
+	.fops                 = &radio_fops,
+	.ioctl_ops 	      = &radio_ioctl_ops,
+	.minor                = -1,
+};
+#endif
 
 void cx23885_video_unregister(struct cx23885_dev *dev)
 {
 	dprintk(1, "%s()\n", __func__);
 	cx_clear(PCI_INT_MSK, 1);
 
+#if 0
+	if (dev->radio_dev) {
+		if (-1 != dev->radio_dev->minor)
+			video_unregister_device(dev->radio_dev);
+		else
+			video_device_release(dev->radio_dev);
+		dev->radio_dev = NULL;
+	}
+	if (dev->vbi_dev) {
+		if (-1 != dev->vbi_dev->minor)
+			video_unregister_device(dev->vbi_dev);
+		else
+			video_device_release(dev->vbi_dev);
+		dev->vbi_dev = NULL;
+		btcx_riscmem_free(dev->pci, &dev->vbiq.stopper);
+	}
+#endif
 	if (dev->video_dev) {
 		if (-1 != dev->video_dev->minor)
 			video_unregister_device(dev->video_dev);
@@ -1513,6 +1733,16 @@
 		VID_A_DMA_CTL, 0x11, 0x00);
 
 	/* Don't enable VBI yet */
+#if 0
+	/* init vbi dma queues */
+	INIT_LIST_HEAD(&dev->vbiq.active);
+	INIT_LIST_HEAD(&dev->vbiq.queued);
+	dev->vbiq.timeout.function = cx23885_vbi_timeout;
+	dev->vbiq.timeout.data = (unsigned long)dev;
+	init_timer(&dev->vbiq.timeout);
+	cx23885_risc_stopper(dev->pci, &dev->vbiq.stopper,
+		VID_A_DMA_CTL, 0x88, 0x00);
+#endif
 	cx_set(PCI_INT_MSK, 1);
 
 	if (TUNER_ABSENT != dev->tuner_type) {
@@ -1521,11 +1751,11 @@
 		if (dev->tuner_addr)
 			sd = v4l2_i2c_new_subdev(&dev->v4l2_dev,
 				&dev->i2c_bus[1].i2c_adap,
-				"tuner", "tuner", dev->tuner_addr);
+				"tuner", "tuner", dev->tuner_addr, NULL);
 		else
-			sd = v4l2_i2c_new_probed_subdev(&dev->v4l2_dev,
+			sd = v4l2_i2c_new_subdev(&dev->v4l2_dev,
 				&dev->i2c_bus[1].i2c_adap,
-				"tuner", "tuner", v4l2_i2c_tuner_addrs(ADDRS_TV));
+				"tuner", "tuner", 0, v4l2_i2c_tuner_addrs(ADDRS_TV));
 		if (sd) {
 			struct tuner_setup tun_setup;
 
@@ -1537,6 +1767,12 @@
 		}
 	}
 
+#if 0
+	if (cx23885_boards[dev->board].audio_chip == V4L2_IDENT_WM8775)
+		/* Must use v4l2_i2c_new_subdev instead of request_module
+		   once this is implemented for real. */
+		request_module("wm8775");
+#endif
 
 	/* register v4l devices */
 	dev->video_dev = cx23885_vdev_init(dev, dev->pci,
@@ -1550,6 +1786,33 @@
 	}
 	printk(KERN_INFO "%s/0: registered device video%d [v4l2]\n",
 	       dev->name, dev->video_dev->num);
+#if 0
+	dev->vbi_dev = cx23885_vdev_init(dev, dev->pci,
+		&cx23885_vbi_template, "vbi");
+	err = video_register_device(dev->vbi_dev, VFL_TYPE_VBI,
+				    vbi_nr[dev->nr]);
+	if (err < 0) {
+		printk(KERN_INFO "%s/0: can't register vbi device\n",
+			dev->name);
+		goto fail_unreg;
+	}
+	printk(KERN_INFO "%s/0: registered device vbi%d\n",
+	       dev->name, dev->vbi_dev->num);
+
+	if (dev->has_radio) {
+		dev->radio_dev = cx23885_vdev_init(dev, dev->pci,
+			&cx23885_radio_template, "radio");
+		err = video_register_device(dev->radio_dev, VFL_TYPE_RADIO,
+					    radio_nr[dev->nr]);
+		if (err < 0) {
+			printk(KERN_INFO "%s/0: can't register radio device\n",
+			       dev->name);
+			goto fail_unreg;
+		}
+		printk(KERN_INFO "%s/0: registered device radio%d\n",
+		       dev->name, dev->radio_dev->num);
+	}
+#endif
 	/* initial device configuration */
 	mutex_lock(&dev->lock);
 	cx23885_set_tvnorm(dev, dev->tvnorm);
Nur in cx23885-commell: cx23888-ir.c.
Nur in cx23885-commell: cx23888-ir.h.
diff -u cx23885/Makefile cx23885-commell/Makefile
--- cx23885/Makefile	2010-02-15 23:22:38.000000000 +0100
+++ cx23885-commell/Makefile	2009-10-25 08:18:46.000000000 +0100
@@ -1,5 +1,6 @@
 cx23885-objs	:= cx23885-cards.o cx23885-video.o cx23885-vbi.o \
 		    cx23885-core.o cx23885-i2c.o cx23885-dvb.o cx23885-417.o \
+		    cx23885-ioctl.o cx23885-ir.o cx23885-input.o cx23888-ir.o \
 		    netup-init.o cimax2.o netup-eeprom.o
 
 obj-$(CONFIG_VIDEO_CX23885) += cx23885.o
Nur in cx23885: modules.order.
diff -u cx23885/netup-eeprom.c cx23885-commell/netup-eeprom.c
--- cx23885/netup-eeprom.c	2010-02-15 23:22:38.000000000 +0100
+++ cx23885-commell/netup-eeprom.c	2009-11-11 09:36:16.000000000 +0100
@@ -97,11 +97,21 @@
 {
 	int i, j;
 
-	cinfo->rev =  netup_eeprom_read(i2c_adap, 13);
+	cinfo->rev =  netup_eeprom_read(i2c_adap, 63);
 
-	for (i = 0, j = 0; i < 6; i++, j++)
+	for (i = 64, j = 0; i < 70; i++, j++)
 		cinfo->port[0].mac[j] =  netup_eeprom_read(i2c_adap, i);
 
-	for (i = 6, j = 0; i < 12; i++, j++)
+	for (i = 70, j = 0; i < 76; i++, j++)
 		cinfo->port[1].mac[j] =  netup_eeprom_read(i2c_adap, i);
+#if 0
+	printk(KERN_INFO "NetUP Dual DVB-S2 CI card rev=0x%x MAC1=%02X:%02X:"
+	"%02X:%02X:%02X:%02X MAC2=%02X:%02X:%02X:%02X:%02X:%02X\n", cinfo->rev,
+		cinfo->port[0].mac[0], cinfo->port[0].mac[1],
+		cinfo->port[0].mac[2], cinfo->port[0].mac[3],
+		cinfo->port[0].mac[4], cinfo->port[0].mac[5],
+		cinfo->port[1].mac[0], cinfo->port[1].mac[1],
+		cinfo->port[1].mac[2], cinfo->port[1].mac[3],
+		cinfo->port[1].mac[4], cinfo->port[1].mac[5]);
+#endif
 };

