@@ -28,6 +28,7 @@
#define ECC_IDLE_MASK BIT(0)
#define ECC_IRQ_EN BIT(0)
+#define ECC_PG_IRQ_SEL BIT(1)
#define ECC_OP_ENABLE (1)
#define ECC_OP_DISABLE (0)
@@ -37,7 +38,6 @@
#define ECC_MS_SHIFT (16)
#define ECC_ENCDIADDR (0x08)
#define ECC_ENCIDLE (0x0C)
-#define ECC_ENCPAR(x) (0x10 + (x) * sizeof(u32))
#define ECC_ENCIRQ_EN (0x80)
#define ECC_ENCIRQ_STA (0x84)
#define ECC_DECCON (0x100)
@@ -61,6 +61,8 @@ struct mtk_ecc_caps {
u32 err_mask;
const u8 *ecc_strength;
u8 num_ecc_strength;
+ u32 encode_parity_reg0;
+ int pg_irq_sel;
};
struct mtk_ecc {
@@ -76,12 +78,17 @@ struct mtk_ecc {
u8 *eccdata;
};
-/* ecc strength that mt2701 supports */
+/* ecc strength that each IP supports */
static const u8 ecc_strength_mt2701[] = {
4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, 32, 36,
40, 44, 48, 52, 56, 60
};
+static const u8 ecc_strength_mt2712[] = {
+ 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, 32, 36,
+ 40, 44, 48, 52, 56, 60, 68, 72, 80
+};
+
static inline void mtk_ecc_wait_idle(struct mtk_ecc *ecc,
enum mtk_ecc_operation op)
{
@@ -254,6 +261,7 @@ struct mtk_ecc *of_mtk_ecc_get(struct device_node *of_node)
int mtk_ecc_enable(struct mtk_ecc *ecc, struct mtk_ecc_config *config)
{
enum mtk_ecc_operation op = config->op;
+ u16 reg_val;
int ret;
ret = mutex_lock_interruptible(&ecc->lock);
@@ -271,7 +279,15 @@ int mtk_ecc_enable(struct mtk_ecc *ecc, struct mtk_ecc_config *config)
writew(ECC_OP_ENABLE, ecc->regs + ECC_CTL_REG(op));
init_completion(&ecc->done);
- writew(ECC_IRQ_EN, ecc->regs + ECC_IRQ_REG(op));
+ reg_val = ECC_IRQ_EN;
+ /*
+ * For ECC_NFI_MODE, if ecc->caps->pg_irq_sel is 1, then it
+ * means this chip can only generate one ecc irq during page
+ * read / write. If is 0, generate one ecc irq each ecc step.
+ */
+ if ((ecc->caps->pg_irq_sel) && (config->mode == ECC_NFI_MODE))
+ reg_val |= ECC_PG_IRQ_SEL;
+ writew(reg_val, ecc->regs + ECC_IRQ_REG(op));
return 0;
}
@@ -341,7 +357,9 @@ int mtk_ecc_encode(struct mtk_ecc *ecc, struct mtk_ecc_config *config,
len = (config->strength * ECC_PARITY_BITS + 7) >> 3;
/* write the parity bytes generated by the ECC back to temp buffer */
- __ioread32_copy(ecc->eccdata, ecc->regs + ECC_ENCPAR(0), round_up(len, 4));
+ __ioread32_copy(ecc->eccdata,
+ ecc->regs + ecc->caps->encode_parity_reg0,
+ round_up(len, 4));
/* copy into possibly unaligned OOB region with actual length */
memcpy(data + bytes, ecc->eccdata, len);
@@ -377,12 +395,25 @@ void mtk_ecc_adjust_strength(struct mtk_ecc *ecc, u32 *p)
.err_mask = 0x3f,
.ecc_strength = ecc_strength_mt2701,
.num_ecc_strength = 20,
+ .encode_parity_reg0 = 0x10,
+ .pg_irq_sel = 0,
+};
+
+static const struct mtk_ecc_caps mtk_ecc_caps_mt2712 = {
+ .err_mask = 0x7f,
+ .ecc_strength = ecc_strength_mt2712,
+ .num_ecc_strength = 23,
+ .encode_parity_reg0 = 0x300,
+ .pg_irq_sel = 1,
};
static const struct of_device_id mtk_ecc_dt_match[] = {
{
.compatible = "mediatek,mt2701-ecc",
.data = &mtk_ecc_caps_mt2701,
+ }, {
+ .compatible = "mediatek,mt2712-ecc",
+ .data = &mtk_ecc_caps_mt2712,
},
{},
};
@@ -163,6 +163,11 @@ struct mtk_nfc {
16, 26, 27, 28, 32, 36, 40, 44, 48, 49, 50, 51, 52, 62, 63, 64
};
+static const u8 spare_size_mt2712[] = {
+ 16, 26, 27, 28, 32, 36, 40, 44, 48, 49, 50, 51, 52, 62, 61, 63, 64, 67,
+ 74
+};
+
static inline struct mtk_nfc_nand_chip *to_mtk_nand(struct nand_chip *nand)
{
return container_of(nand, struct mtk_nfc_nand_chip, nand);
@@ -1323,10 +1328,19 @@ static int mtk_nfc_nand_chips_init(struct device *dev, struct mtk_nfc *nfc)
.pageformat_spare_shift = 4,
};
+static const struct mtk_nfc_caps mtk_nfc_caps_mt2712 = {
+ .spare_size = spare_size_mt2712,
+ .num_spare_size = 19,
+ .pageformat_spare_shift = 16,
+};
+
static const struct of_device_id mtk_nfc_id_table[] = {
{
.compatible = "mediatek,mt2701-nfc",
.data = &mtk_nfc_caps_mt2701,
+ }, {
+ .compatible = "mediatek,mt2712-nfc",
+ .data = &mtk_nfc_caps_mt2712,
},
{}
};
MT2712 NAND FLASH Controller is similar to MT2701 except those following: (1) MT2712 supports up to 148B spare size per 1KB size sector (the same with 74B spare size per 512B size sector). There are three new spare format: 61, 67, 74. (2) MT2712 supports up to 80 bit ecc strength. There are three new ecc strength level: 68, 72, 80. (3) MT2712 ECC encode parity data register's start offset is 0x300, and different with 0x10 of MT2701. (4) MT2712 improves ecc irq function. When ECC works in ECC_NFI_MODE, MT2701 will generate ecc irq number the same with ecc steps during page read. However, MT2712 can only generate one ecc irq. Changes of this patch are: (1) add two new variables named pg_irq_sel, encode_parity_reg0 in struct mtk_ecc_caps. (2) add new bitfield ECC_PG_IRQ_SEL for register ECC_IRQ_REG. (3) add ecc strength array of mt2712. (4) add spare size array of mt2712. (5) add mt2712 nfc and ecc device compatiable and data. Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com> --- drivers/mtd/nand/mtk_ecc.c | 39 +++++++++++++++++++++++++++++++++++---- drivers/mtd/nand/mtk_nand.c | 14 ++++++++++++++ 2 files changed, 49 insertions(+), 4 deletions(-)