new file mode 100644
@@ -0,0 +1,38 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pci/mediatek-pcie-cfg.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Mediatek PCIECFG controller
+
+maintainers:
+ - Chuanjia Liu <chuanjia.liu@mediatek.com>
+ - Jianjun Wang <jianjun.wang@mediatek.com>
+
+description: |
+ The MediaTek PCIECFG controller controls some feature about
+ LTSSM, ASPM and so on.
+
+properties:
+ compatible:
+ items:
+ - enum:
+ - mediatek,mt7622-pciecfg
+ - mediatek,mt7629-pciecfg
+ - const: syscon
+
+ reg:
+ maxItems: 1
+
+required:
+ - compatible
+ - reg
+
+examples:
+ - |
+ pciecfg: pciecfg@1a140000 {
+ compatible = "mediatek,mt7622-pciecfg", "syscon";
+ reg = <0 0x1a140000 0 0x1000>;
+ };
+...
@@ -8,7 +8,7 @@ Required properties:
"mediatek,mt7623-pcie"
"mediatek,mt7629-pcie"
- device_type: Must be "pci"
-- reg: Base addresses and lengths of the PCIe subsys and root ports.
+- reg: Base addresses and lengths of the root ports.
- reg-names: Names of the above areas to use during resource lookup.
- #address-cells: Address representation for root ports (must be 3)
- #size-cells: Size representation for root ports (must be 2)
@@ -19,10 +19,10 @@ Required properties:
- sys_ckN :transaction layer and data link layer clock
Required entries for MT2701/MT7623:
- free_ck :for reference clock of PCIe subsys
- Required entries for MT2712/MT7622:
+ Required entries for MT2712/MT7622/MT7629:
- ahb_ckN :AHB slave interface operating clock for CSR access and RC
initiated MMIO access
- Required entries for MT7622:
+ Required entries for MT7622/MT7629:
- axi_ckN :application layer MMIO channel operating clock
- aux_ckN :pe2_mac_bridge and pe2_mac_core operating clock when
pcie_mac_ck/pcie_pipe_ck is turned off
@@ -47,10 +47,13 @@ Required properties for MT7623/MT2701:
- reset-names: Must be "pcie-rst0", "pcie-rst1", "pcie-rstN".. based on the
number of root ports.
-Required properties for MT2712/MT7622:
+Required properties for MT2712/MT7622/MT7629:
-interrupts: A list of interrupt outputs of the controller, must have one
entry for each PCIe port
+Required properties for MT7622/MT7629:
+- mediatek,pcie-subsys: Should be a phandle of the pciecfg node.
+
In addition, the device tree node must have sub-nodes describing each
PCIe port interface, having the following mandatory properties:
@@ -143,56 +146,73 @@ Examples for MT7623:
Examples for MT2712:
- pcie: pcie@11700000 {
+ pcie1: pcie@112ff000 {
compatible = "mediatek,mt2712-pcie";
device_type = "pci";
- reg = <0 0x11700000 0 0x1000>,
- <0 0x112ff000 0 0x1000>;
- reg-names = "port0", "port1";
+ reg = <0 0x112ff000 0 0x1000>;
+ reg-names = "port1";
#address-cells = <3>;
#size-cells = <2>;
- interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&topckgen CLK_TOP_PE2_MAC_P0_SEL>,
- <&topckgen CLK_TOP_PE2_MAC_P1_SEL>,
- <&pericfg CLK_PERI_PCIE0>,
+ interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "pcie_irq";
+ clocks = <&topckgen CLK_TOP_PE2_MAC_P1_SEL>,
<&pericfg CLK_PERI_PCIE1>;
- clock-names = "sys_ck0", "sys_ck1", "ahb_ck0", "ahb_ck1";
- phys = <&pcie0_phy PHY_TYPE_PCIE>, <&pcie1_phy PHY_TYPE_PCIE>;
- phy-names = "pcie-phy0", "pcie-phy1";
+ clock-names = "sys_ck1", "ahb_ck1";
+ phys = <&u3port1 PHY_TYPE_PCIE>;
+ phy-names = "pcie-phy1";
bus-range = <0x00 0xff>;
- ranges = <0x82000000 0 0x20000000 0x0 0x20000000 0 0x10000000>;
+ ranges = <0x82000000 0 0x11400000 0x0 0x11400000 0 0x300000>;
+ status = "disabled";
- pcie0: pcie@0,0 {
- reg = <0x0000 0 0 0 0>;
+ slot1: pcie@1,0 {
+ reg = <0x0800 0 0 0 0>;
#address-cells = <3>;
#size-cells = <2>;
#interrupt-cells = <1>;
ranges;
interrupt-map-mask = <0 0 0 7>;
- interrupt-map = <0 0 0 1 &pcie_intc0 0>,
- <0 0 0 2 &pcie_intc0 1>,
- <0 0 0 3 &pcie_intc0 2>,
- <0 0 0 4 &pcie_intc0 3>;
- pcie_intc0: interrupt-controller {
+ interrupt-map = <0 0 0 1 &pcie_intc1 0>,
+ <0 0 0 2 &pcie_intc1 1>,
+ <0 0 0 3 &pcie_intc1 2>,
+ <0 0 0 4 &pcie_intc1 3>;
+ pcie_intc1: interrupt-controller {
interrupt-controller;
#address-cells = <0>;
#interrupt-cells = <1>;
};
};
+ };
- pcie1: pcie@1,0 {
- reg = <0x0800 0 0 0 0>;
+ pcie0: pcie@11700000 {
+ compatible = "mediatek,mt2712-pcie";
+ device_type = "pci";
+ reg = <0 0x11700000 0 0x1000>;
+ reg-names = "port0";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "pcie_irq";
+ clocks = <&topckgen CLK_TOP_PE2_MAC_P0_SEL>,
+ <&pericfg CLK_PERI_PCIE0>;
+ clock-names = "sys_ck0", "ahb_ck0";
+ phys = <&u3port0 PHY_TYPE_PCIE>;
+ phy-names = "pcie-phy0";
+ bus-range = <0x00 0xff>;
+ ranges = <0x82000000 0 0x20000000 0x0 0x20000000 0 0x10000000>;
+ status = "disabled";
+
+ slot0: pcie@0,0 {
+ reg = <0x0000 0 0 0 0>;
#address-cells = <3>;
#size-cells = <2>;
#interrupt-cells = <1>;
ranges;
interrupt-map-mask = <0 0 0 7>;
- interrupt-map = <0 0 0 1 &pcie_intc1 0>,
- <0 0 0 2 &pcie_intc1 1>,
- <0 0 0 3 &pcie_intc1 2>,
- <0 0 0 4 &pcie_intc1 3>;
- pcie_intc1: interrupt-controller {
+ interrupt-map = <0 0 0 1 &pcie_intc0 0>,
+ <0 0 0 2 &pcie_intc0 1>,
+ <0 0 0 3 &pcie_intc0 2>,
+ <0 0 0 4 &pcie_intc0 3>;
+ pcie_intc0: interrupt-controller {
interrupt-controller;
#address-cells = <0>;
#interrupt-cells = <1>;
@@ -202,39 +222,31 @@ Examples for MT2712:
Examples for MT7622:
- pcie: pcie@1a140000 {
+ pcie0: pcie@1a143000 {
compatible = "mediatek,mt7622-pcie";
device_type = "pci";
- reg = <0 0x1a140000 0 0x1000>,
- <0 0x1a143000 0 0x1000>,
- <0 0x1a145000 0 0x1000>;
- reg-names = "subsys", "port0", "port1";
+ reg = <0 0x1a143000 0 0x1000>;
+ reg-names = "port0";
+ mediatek,pcie-cfg = <&pciecfg>;
#address-cells = <3>;
#size-cells = <2>;
- interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_LOW>,
- <GIC_SPI 229 IRQ_TYPE_LEVEL_LOW>;
+ interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-names = "pcie_irq";
clocks = <&pciesys CLK_PCIE_P0_MAC_EN>,
- <&pciesys CLK_PCIE_P1_MAC_EN>,
<&pciesys CLK_PCIE_P0_AHB_EN>,
- <&pciesys CLK_PCIE_P1_AHB_EN>,
<&pciesys CLK_PCIE_P0_AUX_EN>,
- <&pciesys CLK_PCIE_P1_AUX_EN>,
<&pciesys CLK_PCIE_P0_AXI_EN>,
- <&pciesys CLK_PCIE_P1_AXI_EN>,
<&pciesys CLK_PCIE_P0_OBFF_EN>,
- <&pciesys CLK_PCIE_P1_OBFF_EN>,
- <&pciesys CLK_PCIE_P0_PIPE_EN>,
- <&pciesys CLK_PCIE_P1_PIPE_EN>;
- clock-names = "sys_ck0", "sys_ck1", "ahb_ck0", "ahb_ck1",
- "aux_ck0", "aux_ck1", "axi_ck0", "axi_ck1",
- "obff_ck0", "obff_ck1", "pipe_ck0", "pipe_ck1";
- phys = <&pcie0_phy PHY_TYPE_PCIE>, <&pcie1_phy PHY_TYPE_PCIE>;
- phy-names = "pcie-phy0", "pcie-phy1";
+ <&pciesys CLK_PCIE_P0_PIPE_EN>;
+ clock-names = "sys_ck0", "ahb_ck0", "aux_ck0",
+ "axi_ck0", "obff_ck0", "pipe_ck0";
+
power-domains = <&scpsys MT7622_POWER_DOMAIN_HIF0>;
bus-range = <0x00 0xff>;
- ranges = <0x82000000 0 0x20000000 0x0 0x20000000 0 0x10000000>;
+ ranges = <0x82000000 0 0x20000000 0 0x20000000 0 0x8000000>;
+ status = "disabled";
- pcie0: pcie@0,0 {
+ slot0: pcie@0,0 {
reg = <0x0000 0 0 0 0>;
#address-cells = <3>;
#size-cells = <2>;
@@ -251,8 +263,34 @@ Examples for MT7622:
#interrupt-cells = <1>;
};
};
+ };
+
+ pcie1: pcie@1a145000 {
+ compatible = "mediatek,mt7622-pcie";
+ device_type = "pci";
+ reg = <0 0x1a145000 0 0x1000>;
+ reg-names = "port1";
+ mediatek,pcie-cfg = <&pciecfg>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-names = "pcie_irq";
+ clocks = <&pciesys CLK_PCIE_P1_MAC_EN>,
+ /* designer has connect RC1 with p0_ahb clock */
+ <&pciesys CLK_PCIE_P0_AHB_EN>,
+ <&pciesys CLK_PCIE_P1_AUX_EN>,
+ <&pciesys CLK_PCIE_P1_AXI_EN>,
+ <&pciesys CLK_PCIE_P1_OBFF_EN>,
+ <&pciesys CLK_PCIE_P1_PIPE_EN>;
+ clock-names = "sys_ck1", "ahb_ck1", "aux_ck1",
+ "axi_ck1", "obff_ck1", "pipe_ck1";
+
+ power-domains = <&scpsys MT7622_POWER_DOMAIN_HIF0>;
+ bus-range = <0x00 0xff>;
+ ranges = <0x82000000 0 0x28000000 0 0x28000000 0 0x8000000>;
+ status = "disabled";
- pcie1: pcie@1,0 {
+ slot1: pcie@1,0 {
reg = <0x0800 0 0 0 0>;
#address-cells = <3>;
#size-cells = <2>;