@@ -31,6 +31,24 @@ config DEBUG_PINCTRL
help
Say Y here to add some extra checks and diagnostics to PINCTRL calls.
+config PINCTRL_AMD
+ tristate "AMD GPIO pin control"
+ depends on HAS_IOMEM
+ depends on ACPI || COMPILE_TEST
+ select GPIOLIB
+ select GPIOLIB_IRQCHIP
+ select PINMUX
+ select PINCONF
+ select GENERIC_PINCONF
+ help
+ The driver for memory mapped GPIO functionality on AMD platforms
+ (x86 or arm). Most of the pins are usually muxed to some other
+ functionality by firmware, so only a small amount is available
+ for GPIO use.
+
+ Requires ACPI/FDT device enumeration code to set up a platform
+ device.
+
config PINCTRL_APPLE_GPIO
tristate "Apple SoC GPIO pin controller driver"
depends on ARCH_APPLE
@@ -69,20 +87,6 @@ config PINCTRL_AS3722
open drain configuration for the GPIO pins of AS3722 devices. It also
supports the GPIO functionality through gpiolib.
-config PINCTRL_AXP209
- tristate "X-Powers AXP209 PMIC pinctrl and GPIO Support"
- depends on MFD_AXP20X
- depends on OF
- select PINMUX
- select GENERIC_PINCONF
- select GPIOLIB
- help
- AXP PMICs provides multiple GPIOs that can be muxed for different
- functions. This driver bundles a pinctrl driver to select the function
- muxing and a GPIO driver to handle the GPIO when the GPIO function is
- selected.
- Say yes to enable pinctrl and GPIO support for the AXP209 PMIC
-
config PINCTRL_AT91
bool "AT91 pinctrl driver"
depends on OF
@@ -109,23 +113,19 @@ config PINCTRL_AT91PIO4
Say Y here to enable the at91 pinctrl/gpio driver for Atmel PIO4
controller available on sama5d2 SoC.
-config PINCTRL_AMD
- tristate "AMD GPIO pin control"
- depends on HAS_IOMEM
- depends on ACPI || COMPILE_TEST
- select GPIOLIB
- select GPIOLIB_IRQCHIP
+config PINCTRL_AXP209
+ tristate "X-Powers AXP209 PMIC pinctrl and GPIO Support"
+ depends on MFD_AXP20X
+ depends on OF
select PINMUX
- select PINCONF
select GENERIC_PINCONF
+ select GPIOLIB
help
- driver for memory mapped GPIO functionality on AMD platforms
- (x86 or arm).Most pins are usually muxed to some other
- functionality by firmware,so only a small amount is available
- for gpio use.
-
- Requires ACPI/FDT device enumeration code to set up a platform
- device.
+ AXP PMICs provides multiple GPIOs that can be muxed for different
+ functions. This driver bundles a pinctrl driver to select the function
+ muxing and a GPIO driver to handle the GPIO when the GPIO function is
+ selected.
+ Say Y to enable pinctrl and GPIO support for the AXP209 PMIC.
config PINCTRL_BM1880
bool "Bitmain BM1880 Pinctrl driver"
@@ -136,13 +136,13 @@ config PINCTRL_BM1880
Pinctrl driver for Bitmain BM1880 SoC.
config PINCTRL_DA850_PUPD
- tristate "TI DA850/OMAP-L138/AM18XX pullup/pulldown groups"
+ tristate "TI DA850/OMAP-L138/AM18XX pull-up and pull-down groups"
depends on OF && (ARCH_DAVINCI_DA850 || COMPILE_TEST)
select PINCONF
select GENERIC_PINCONF
help
Driver for TI DA850/OMAP-L138/AM18XX pinconf. Used to control
- pullup/pulldown pin groups.
+ pull-up and pull-down pin groups.
config PINCTRL_DA9062
tristate "Dialog Semiconductor DA9062 PMIC pinctrl and GPIO Support"
@@ -154,7 +154,7 @@ config PINCTRL_DA9062
function muxing and a GPIO driver to handle the GPIO when the GPIO
function is selected.
- Say yes to enable pinctrl and GPIO support for the DA9062 PMIC.
+ Say Y to enable pinctrl and GPIO support for the DA9062 PMIC.
config PINCTRL_DIGICOLOR
bool
@@ -162,12 +162,93 @@ config PINCTRL_DIGICOLOR
select PINMUX
select GENERIC_PINCONF
+config PINCTRL_EQUILIBRIUM
+ tristate "Generic pinctrl and GPIO driver for Intel Lightning Mountain SoC"
+ depends on OF && HAS_IOMEM
+ depends on X86 || COMPILE_TEST
+ select PINMUX
+ select PINCONF
+ select GPIOLIB
+ select GPIO_GENERIC
+ select GPIOLIB_IRQCHIP
+ select GENERIC_PINCONF
+ select GENERIC_PINCTRL_GROUPS
+ select GENERIC_PINMUX_FUNCTIONS
+ help
+ Equilibrium driver is a pinctrl and GPIO driver for Intel Lightning
+ Mountain network processor SoC that supports both the GPIO and pin
+ control frameworks. It provides interfaces to setup pin muxing, assign
+ desired pin functions, configure GPIO attributes for LGM SoC pins.
+ Pin muxing and pin config settings are retrieved from device tree.
+
+config PINCTRL_GEMINI
+ bool
+ depends on ARCH_GEMINI
+ default ARCH_GEMINI
+ select PINMUX
+ select GENERIC_PINCONF
+ select MFD_SYSCON
+
+config PINCTRL_INGENIC
+ bool "Pinctrl driver for the Ingenic JZ47xx SoCs"
+ default MACH_INGENIC
+ depends on OF
+ depends on MIPS || COMPILE_TEST
+ select GENERIC_PINCONF
+ select GENERIC_PINCTRL_GROUPS
+ select GENERIC_PINMUX_FUNCTIONS
+ select GPIOLIB
+ select GPIOLIB_IRQCHIP
+ select REGMAP_MMIO
+
+config PINCTRL_K210
+ bool "Pinctrl driver for the Canaan Kendryte K210 SoC"
+ depends on RISCV && SOC_CANAAN && OF
+ select GENERIC_PINMUX_FUNCTIONS
+ select GENERIC_PINCONF
+ select GPIOLIB
+ select OF_GPIO
+ select REGMAP_MMIO
+ default SOC_CANAAN
+ help
+ Add support for the Canaan Kendryte K210 RISC-V SOC Field
+ Programmable IO Array (FPIOA) controller.
+
+config PINCTRL_KEEMBAY
+ tristate "Pinctrl driver for Intel Keem Bay SoC"
+ depends on ARCH_KEEMBAY || (ARM64 && COMPILE_TEST)
+ depends on HAS_IOMEM
+ select PINMUX
+ select PINCONF
+ select GENERIC_PINCONF
+ select GENERIC_PINCTRL_GROUPS
+ select GENERIC_PINMUX_FUNCTIONS
+ select GPIOLIB
+ select GPIOLIB_IRQCHIP
+ select GPIO_GENERIC
+ help
+ This selects pin control driver for the Intel Keem Bay SoC.
+ It provides pin config functions such as pull-up, pull-down,
+ interrupt, drive strength, sec lock, Schmitt trigger, slew
+ rate control and direction control. This module will be
+ called as pinctrl-keembay.
+
config PINCTRL_LANTIQ
bool
depends on LANTIQ
select PINMUX
select PINCONF
+config PINCTRL_FALCON
+ bool
+ depends on SOC_FALCON
+ depends on PINCTRL_LANTIQ
+
+config PINCTRL_XWAY
+ bool
+ depends on SOC_TYPE_XWAY
+ depends on PINCTRL_LANTIQ
+
config PINCTRL_LPC18XX
bool "NXP LPC18XX/43XX SCU pinctrl driver"
depends on OF && (ARCH_LPC18XX || COMPILE_TEST)
@@ -177,18 +258,16 @@ config PINCTRL_LPC18XX
help
Pinctrl driver for NXP LPC18xx/43xx System Control Unit (SCU).
-config PINCTRL_FALCON
- bool
- depends on SOC_FALCON
- depends on PINCTRL_LANTIQ
-
-config PINCTRL_GEMINI
- bool
- depends on ARCH_GEMINI
- default ARCH_GEMINI
+config PINCTRL_MAX77620
+ tristate "MAX77620/MAX20024 Pincontrol support"
+ depends on MFD_MAX77620 && OF
select PINMUX
select GENERIC_PINCONF
- select MFD_SYSCON
+ help
+ Say Y here to enable Pin control support for Maxim MAX77620 PMIC.
+ This PMIC has 8 GPIO pins that work as GPIO as well as special
+ function in alternate mode. This driver also configure push-pull,
+ open drain, FPS slots etc.
config PINCTRL_MCP23S08_I2C
tristate
@@ -212,99 +291,47 @@ config PINCTRL_MCP23S08
This provides a GPIO interface supporting inputs and outputs and a
corresponding interrupt-controller.
-config PINCTRL_OXNAS
- bool
+config PINCTRL_MICROCHIP_SGPIO
+ bool "Pinctrl driver for Microsemi/Microchip Serial GPIO"
depends on OF
- select PINMUX
- select PINCONF
- select GENERIC_PINCONF
+ depends on HAS_IOMEM
select GPIOLIB
- select OF_GPIO
select GPIOLIB_IRQCHIP
- select MFD_SYSCON
-
-config PINCTRL_ROCKCHIP
- tristate "Rockchip gpio and pinctrl driver"
- depends on ARCH_ROCKCHIP || COMPILE_TEST
- depends on OF
- select GPIOLIB
- select PINMUX
select GENERIC_PINCONF
- select GENERIC_IRQ_CHIP
- select MFD_SYSCON
+ select GENERIC_PINCTRL_GROUPS
+ select GENERIC_PINMUX_FUNCTIONS
select OF_GPIO
- default ARCH_ROCKCHIP
help
- This support pinctrl and gpio driver for Rockchip SoCs.
+ Support for the serial GPIO interface used on Microsemi and
+ Microchip SoCs. By using a serial interface, the SIO
+ controller significantly extends the number of available
+ GPIOs with a minimum number of additional pins on the
+ device. The primary purpose of the SIO controller is to
+ connect control signals from SFP modules and to act as an
+ LED controller.
-config PINCTRL_SINGLE
- tristate "One-register-per-pin type device tree based pinctrl driver"
+config PINCTRL_OCELOT
+ bool "Pinctrl driver for the Microsemi Ocelot and Jaguar2 SoCs"
depends on OF
depends on HAS_IOMEM
- select GENERIC_PINCTRL_GROUPS
- select GENERIC_PINMUX_FUNCTIONS
- select GENERIC_PINCONF
- help
- This selects the device tree based generic pinctrl driver.
-
-config PINCTRL_SX150X
- bool "Semtech SX150x I2C GPIO expander pinctrl driver"
- depends on I2C=y
- select PINMUX
- select PINCONF
- select GENERIC_PINCONF
select GPIOLIB
select GPIOLIB_IRQCHIP
- select REGMAP
- help
- Say yes here to provide support for Semtech SX150x-series I2C
- GPIO expanders as pinctrl module.
- Compatible models include:
- - 8 bits: sx1508q, sx1502q
- - 16 bits: sx1509q, sx1506q
-
-config PINCTRL_PISTACHIO
- bool "IMG Pistachio SoC pinctrl driver"
- depends on OF && (MIPS || COMPILE_TEST)
- depends on GPIOLIB
- select PINMUX
select GENERIC_PINCONF
- select GPIOLIB_IRQCHIP
+ select GENERIC_PINCTRL_GROUPS
+ select GENERIC_PINMUX_FUNCTIONS
select OF_GPIO
- help
- This support pinctrl and gpio driver for IMG Pistachio SoC.
+ select REGMAP_MMIO
-config PINCTRL_ST
+config PINCTRL_OXNAS
bool
depends on OF
select PINMUX
select PINCONF
- select GPIOLIB_IRQCHIP
-
-config PINCTRL_STMFX
- tristate "STMicroelectronics STMFX GPIO expander pinctrl driver"
- depends on I2C
- depends on OF_GPIO
select GENERIC_PINCONF
+ select GPIOLIB
+ select OF_GPIO
select GPIOLIB_IRQCHIP
- select MFD_STMFX
- help
- Driver for STMicroelectronics Multi-Function eXpander (STMFX)
- GPIO expander.
- This provides a GPIO interface supporting inputs and outputs,
- and configuring push-pull, open-drain, and can also be used as
- interrupt-controller.
-
-config PINCTRL_MAX77620
- tristate "MAX77620/MAX20024 Pincontrol support"
- depends on MFD_MAX77620 && OF
- select PINMUX
- select GENERIC_PINCONF
- help
- Say Yes here to enable Pin control support for Maxim PMIC MAX77620.
- This PMIC has 8 GPIO pins that work as GPIO as well as special
- function in alternate mode. This driver also configure push-pull,
- open drain, FPS slots etc.
+ select MFD_SYSCON
config PINCTRL_PALMAS
tristate "Pinctrl driver for the PALMAS Series MFD devices"
@@ -334,41 +361,16 @@ config PINCTRL_PIC32MZDA
def_bool y if PIC32MZDA
select PINCTRL_PIC32
-config PINCTRL_ZYNQ
- bool "Pinctrl driver for Xilinx Zynq"
- depends on ARCH_ZYNQ
- select PINMUX
- select GENERIC_PINCONF
- help
- This selects the pinctrl driver for Xilinx Zynq.
-
-config PINCTRL_ZYNQMP
- tristate "Pinctrl driver for Xilinx ZynqMP"
- depends on ZYNQMP_FIRMWARE
+config PINCTRL_PISTACHIO
+ bool "IMG Pistachio SoC pinctrl driver"
+ depends on OF && (MIPS || COMPILE_TEST)
+ depends on GPIOLIB
select PINMUX
select GENERIC_PINCONF
- default ZYNQMP_FIRMWARE
- help
- This selects the pinctrl driver for Xilinx ZynqMP platform.
- This driver will query the pin information from the firmware
- and allow configuring the pins.
- Configuration can include the mux function to select on those
- pin(s)/group(s), and various pin configuration parameters
- such as pull-up, slew rate, etc.
- This driver can also be built as a module. If so, the module
- will be called pinctrl-zynqmp.
-
-config PINCTRL_INGENIC
- bool "Pinctrl driver for the Ingenic JZ47xx SoCs"
- default MACH_INGENIC
- depends on OF
- depends on MIPS || COMPILE_TEST
- select GENERIC_PINCONF
- select GENERIC_PINCTRL_GROUPS
- select GENERIC_PINMUX_FUNCTIONS
- select GPIOLIB
select GPIOLIB_IRQCHIP
- select REGMAP_MMIO
+ select OF_GPIO
+ help
+ This support pinctrl and GPIO driver for IMG Pistachio SoC.
config PINCTRL_RK805
tristate "Pinctrl and GPIO driver for RK805 PMIC"
@@ -379,53 +381,75 @@ config PINCTRL_RK805
help
This selects the pinctrl driver for RK805.
-config PINCTRL_OCELOT
- bool "Pinctrl driver for the Microsemi Ocelot and Jaguar2 SoCs"
+config PINCTRL_ROCKCHIP
+ tristate "Rockchip gpio and pinctrl driver"
+ depends on ARCH_ROCKCHIP || COMPILE_TEST
depends on OF
- depends on HAS_IOMEM
select GPIOLIB
- select GPIOLIB_IRQCHIP
+ select PINMUX
select GENERIC_PINCONF
- select GENERIC_PINCTRL_GROUPS
- select GENERIC_PINMUX_FUNCTIONS
+ select GENERIC_IRQ_CHIP
+ select MFD_SYSCON
select OF_GPIO
- select REGMAP_MMIO
+ default ARCH_ROCKCHIP
+ help
+ This support pinctrl and GPIO driver for Rockchip SoCs.
-config PINCTRL_MICROCHIP_SGPIO
- bool "Pinctrl driver for Microsemi/Microchip Serial GPIO"
+config PINCTRL_SINGLE
+ tristate "One-register-per-pin type device tree based pinctrl driver"
depends on OF
depends on HAS_IOMEM
- select GPIOLIB
- select GPIOLIB_IRQCHIP
- select GENERIC_PINCONF
select GENERIC_PINCTRL_GROUPS
select GENERIC_PINMUX_FUNCTIONS
- select OF_GPIO
+ select GENERIC_PINCONF
help
- Support for the serial GPIO interface used on Microsemi and
- Microchip SoC's. By using a serial interface, the SIO
- controller significantly extends the number of available
- GPIOs with a minimum number of additional pins on the
- device. The primary purpose of the SIO controller is to
- connect control signals from SFP modules and to act as an
- LED controller.
+ This selects the device tree based generic pinctrl driver.
-config PINCTRL_K210
- bool "Pinctrl driver for the Canaan Kendryte K210 SoC"
- depends on RISCV && SOC_CANAAN && OF
- select GENERIC_PINMUX_FUNCTIONS
+config PINCTRL_ST
+ bool
+ depends on OF
+ select PINMUX
+ select PINCONF
+ select GPIOLIB_IRQCHIP
+
+config PINCTRL_STMFX
+ tristate "STMicroelectronics STMFX GPIO expander pinctrl driver"
+ depends on I2C
+ depends on OF_GPIO
+ select GENERIC_PINCONF
+ select GPIOLIB_IRQCHIP
+ select MFD_STMFX
+ help
+ Driver for STMicroelectronics Multi-Function eXpander (STMFX)
+ GPIO expander.
+ This provides a GPIO interface supporting inputs and outputs,
+ and configuring push-pull, open-drain, and can also be used as
+ interrupt-controller.
+
+config PINCTRL_SX150X
+ bool "Semtech SX150x I2C GPIO expander pinctrl driver"
+ depends on I2C=y
+ select PINMUX
+ select PINCONF
select GENERIC_PINCONF
select GPIOLIB
- select OF_GPIO
- select REGMAP_MMIO
- default SOC_CANAAN
+ select GPIOLIB_IRQCHIP
+ select REGMAP
help
- Add support for the Canaan Kendryte K210 RISC-V SOC Field
- Programmable IO Array (FPIOA) controller.
+ Say Y here to provide support for Semtech SX150x-series I2C
+ GPIO expanders as pinctrl module.
+ Compatible models include:
+ - 8 bits: sx1508q, sx1502q
+ - 16 bits: sx1509q, sx1506q
-config PINCTRL_KEEMBAY
- tristate "Pinctrl driver for Intel Keem Bay SoC"
- depends on ARCH_KEEMBAY || (ARM64 && COMPILE_TEST)
+config PINCTRL_TB10X
+ bool
+ depends on OF && ARC_PLAT_TB10X
+ select GPIOLIB
+
+config PINCTRL_THUNDERBAY
+ tristate "Generic pinctrl and GPIO driver for Intel Thunder Bay SoC"
+ depends on ARCH_THUNDERBAY || (ARM64 && COMPILE_TEST)
depends on HAS_IOMEM
select PINMUX
select PINCONF
@@ -436,18 +460,45 @@ config PINCTRL_KEEMBAY
select GPIOLIB_IRQCHIP
select GPIO_GENERIC
help
- This selects pin control driver for the Intel Keembay SoC.
- It provides pin config functions such as pullup, pulldown,
- interrupt, drive strength, sec lock, schmitt trigger, slew
+ This selects pin control driver for the Intel Thunder Bay SoC.
+ It provides pin config functions such as pull-up, pull-down,
+ interrupt, drive strength, sec lock, Schmitt trigger, slew
rate control and direction control. This module will be
- called as pinctrl-keembay.
+ called as pinctrl-thunderbay.
+
+config PINCTRL_ZYNQ
+ bool "Pinctrl driver for Xilinx Zynq"
+ depends on ARCH_ZYNQ
+ select PINMUX
+ select GENERIC_PINCONF
+ help
+ This selects the pinctrl driver for Xilinx Zynq.
+
+config PINCTRL_ZYNQMP
+ tristate "Pinctrl driver for Xilinx ZynqMP"
+ depends on ZYNQMP_FIRMWARE
+ select PINMUX
+ select GENERIC_PINCONF
+ default ZYNQMP_FIRMWARE
+ help
+ This selects the pinctrl driver for Xilinx ZynqMP platform.
+ This driver will query the pin information from the firmware
+ and allow configuring the pins.
+ Configuration can include the mux function to select on those
+ pin(s)/group(s), and various pin configuration parameters
+ such as pull-up, slew rate, etc.
+ This driver can also be built as a module. If so, the module
+ will be called pinctrl-zynqmp.
source "drivers/pinctrl/actions/Kconfig"
source "drivers/pinctrl/aspeed/Kconfig"
source "drivers/pinctrl/bcm/Kconfig"
source "drivers/pinctrl/berlin/Kconfig"
+source "drivers/pinctrl/cirrus/Kconfig"
source "drivers/pinctrl/freescale/Kconfig"
source "drivers/pinctrl/intel/Kconfig"
+source "drivers/pinctrl/mediatek/Kconfig"
+source "drivers/pinctrl/meson/Kconfig"
source "drivers/pinctrl/mvebu/Kconfig"
source "drivers/pinctrl/nomadik/Kconfig"
source "drivers/pinctrl/nuvoton/Kconfig"
@@ -463,59 +514,7 @@ source "drivers/pinctrl/sunxi/Kconfig"
source "drivers/pinctrl/tegra/Kconfig"
source "drivers/pinctrl/ti/Kconfig"
source "drivers/pinctrl/uniphier/Kconfig"
-source "drivers/pinctrl/vt8500/Kconfig"
-source "drivers/pinctrl/mediatek/Kconfig"
-source "drivers/pinctrl/meson/Kconfig"
-source "drivers/pinctrl/cirrus/Kconfig"
source "drivers/pinctrl/visconti/Kconfig"
-
-config PINCTRL_XWAY
- bool
- depends on SOC_TYPE_XWAY
- depends on PINCTRL_LANTIQ
-
-config PINCTRL_TB10X
- bool
- depends on OF && ARC_PLAT_TB10X
- select GPIOLIB
-
-config PINCTRL_EQUILIBRIUM
- tristate "Generic pinctrl and GPIO driver for Intel Lightning Mountain SoC"
- depends on OF && HAS_IOMEM
- depends on X86 || COMPILE_TEST
- select PINMUX
- select PINCONF
- select GPIOLIB
- select GPIO_GENERIC
- select GPIOLIB_IRQCHIP
- select GENERIC_PINCONF
- select GENERIC_PINCTRL_GROUPS
- select GENERIC_PINMUX_FUNCTIONS
-
- help
- Equilibrium pinctrl driver is a pinctrl & GPIO driver for Intel Lightning
- Mountain network processor SoC that supports both the linux GPIO and pin
- control frameworks. It provides interfaces to setup pinmux, assign desired
- pin functions, configure GPIO attributes for LGM SoC pins. Pinmux and
- pinconf settings are retrieved from device tree.
-
-config PINCTRL_THUNDERBAY
- tristate "Generic pinctrl and GPIO driver for Intel Thunder Bay SoC"
- depends on ARCH_THUNDERBAY || (ARM64 && COMPILE_TEST)
- depends on HAS_IOMEM
- select PINMUX
- select PINCONF
- select GENERIC_PINCONF
- select GENERIC_PINCTRL_GROUPS
- select GENERIC_PINMUX_FUNCTIONS
- select GPIOLIB
- select GPIOLIB_IRQCHIP
- select GPIO_GENERIC
- help
- This selects pin control driver for the Intel Thunder Bay SoC.
- It provides pin config functions such as pullup, pulldown,
- interrupt, drive strength, sec lock, schmitt trigger, slew
- rate control and direction control. This module will be
- called as pinctrl-thunderbay.
+source "drivers/pinctrl/vt8500/Kconfig"
endif
@@ -6,57 +6,59 @@ subdir-ccflags-$(CONFIG_DEBUG_PINCTRL) += -DDEBUG
obj-y += core.o pinctrl-utils.o
obj-$(CONFIG_PINMUX) += pinmux.o
obj-$(CONFIG_PINCONF) += pinconf.o
-obj-$(CONFIG_OF) += devicetree.o
obj-$(CONFIG_GENERIC_PINCONF) += pinconf-generic.o
+obj-$(CONFIG_OF) += devicetree.o
+
+obj-$(CONFIG_PINCTRL_AMD) += pinctrl-amd.o
obj-$(CONFIG_PINCTRL_APPLE_GPIO) += pinctrl-apple-gpio.o
obj-$(CONFIG_PINCTRL_ARTPEC6) += pinctrl-artpec6.o
obj-$(CONFIG_PINCTRL_AS3722) += pinctrl-as3722.o
-obj-$(CONFIG_PINCTRL_AXP209) += pinctrl-axp209.o
obj-$(CONFIG_PINCTRL_AT91) += pinctrl-at91.o
obj-$(CONFIG_PINCTRL_AT91PIO4) += pinctrl-at91-pio4.o
-obj-$(CONFIG_PINCTRL_AMD) += pinctrl-amd.o
+obj-$(CONFIG_PINCTRL_AXP209) += pinctrl-axp209.o
obj-$(CONFIG_PINCTRL_BM1880) += pinctrl-bm1880.o
obj-$(CONFIG_PINCTRL_DA850_PUPD) += pinctrl-da850-pupd.o
obj-$(CONFIG_PINCTRL_DA9062) += pinctrl-da9062.o
obj-$(CONFIG_PINCTRL_DIGICOLOR) += pinctrl-digicolor.o
-obj-$(CONFIG_PINCTRL_FALCON) += pinctrl-falcon.o
+obj-$(CONFIG_PINCTRL_EQUILIBRIUM) += pinctrl-equilibrium.o
obj-$(CONFIG_PINCTRL_GEMINI) += pinctrl-gemini.o
+obj-$(CONFIG_PINCTRL_INGENIC) += pinctrl-ingenic.o
+obj-$(CONFIG_PINCTRL_K210) += pinctrl-k210.o
+obj-$(CONFIG_PINCTRL_KEEMBAY) += pinctrl-keembay.o
+obj-$(CONFIG_PINCTRL_LANTIQ) += pinctrl-lantiq.o
+obj-$(CONFIG_PINCTRL_FALCON) += pinctrl-falcon.o
+obj-$(CONFIG_PINCTRL_XWAY) += pinctrl-xway.o
+obj-$(CONFIG_PINCTRL_LPC18XX) += pinctrl-lpc18xx.o
obj-$(CONFIG_PINCTRL_MAX77620) += pinctrl-max77620.o
obj-$(CONFIG_PINCTRL_MCP23S08_I2C) += pinctrl-mcp23s08_i2c.o
obj-$(CONFIG_PINCTRL_MCP23S08_SPI) += pinctrl-mcp23s08_spi.o
obj-$(CONFIG_PINCTRL_MCP23S08) += pinctrl-mcp23s08.o
-obj-$(CONFIG_PINCTRL_MESON) += meson/
+obj-$(CONFIG_PINCTRL_MICROCHIP_SGPIO) += pinctrl-microchip-sgpio.o
+obj-$(CONFIG_PINCTRL_OCELOT) += pinctrl-ocelot.o
obj-$(CONFIG_PINCTRL_OXNAS) += pinctrl-oxnas.o
obj-$(CONFIG_PINCTRL_PALMAS) += pinctrl-palmas.o
obj-$(CONFIG_PINCTRL_PIC32) += pinctrl-pic32.o
obj-$(CONFIG_PINCTRL_PISTACHIO) += pinctrl-pistachio.o
+obj-$(CONFIG_PINCTRL_RK805) += pinctrl-rk805.o
obj-$(CONFIG_PINCTRL_ROCKCHIP) += pinctrl-rockchip.o
obj-$(CONFIG_PINCTRL_SINGLE) += pinctrl-single.o
+obj-$(CONFIG_PINCTRL_STMFX) += pinctrl-stmfx.o
+obj-$(CONFIG_PINCTRL_ST) += pinctrl-st.o
obj-$(CONFIG_PINCTRL_SX150X) += pinctrl-sx150x.o
-obj-$(CONFIG_ARCH_TEGRA) += tegra/
-obj-$(CONFIG_PINCTRL_XWAY) += pinctrl-xway.o
-obj-$(CONFIG_PINCTRL_LANTIQ) += pinctrl-lantiq.o
-obj-$(CONFIG_PINCTRL_LPC18XX) += pinctrl-lpc18xx.o
obj-$(CONFIG_PINCTRL_TB10X) += pinctrl-tb10x.o
-obj-$(CONFIG_PINCTRL_ST) += pinctrl-st.o
-obj-$(CONFIG_PINCTRL_STMFX) += pinctrl-stmfx.o
-obj-$(CONFIG_PINCTRL_ZYNQ) += pinctrl-zynq.o
-obj-$(CONFIG_PINCTRL_ZYNQMP) += pinctrl-zynqmp.o
-obj-$(CONFIG_PINCTRL_INGENIC) += pinctrl-ingenic.o
-obj-$(CONFIG_PINCTRL_RK805) += pinctrl-rk805.o
-obj-$(CONFIG_PINCTRL_OCELOT) += pinctrl-ocelot.o
-obj-$(CONFIG_PINCTRL_MICROCHIP_SGPIO) += pinctrl-microchip-sgpio.o
-obj-$(CONFIG_PINCTRL_EQUILIBRIUM) += pinctrl-equilibrium.o
-obj-$(CONFIG_PINCTRL_K210) += pinctrl-k210.o
-obj-$(CONFIG_PINCTRL_KEEMBAY) += pinctrl-keembay.o
obj-$(CONFIG_PINCTRL_THUNDERBAY) += pinctrl-thunderbay.o
+obj-$(CONFIG_PINCTRL_ZYNQMP) += pinctrl-zynqmp.o
+obj-$(CONFIG_PINCTRL_ZYNQ) += pinctrl-zynq.o
obj-y += actions/
obj-$(CONFIG_ARCH_ASPEED) += aspeed/
obj-y += bcm/
obj-$(CONFIG_PINCTRL_BERLIN) += berlin/
+obj-y += cirrus/
obj-y += freescale/
obj-$(CONFIG_X86) += intel/
+obj-y += mediatek/
+obj-$(CONFIG_PINCTRL_MESON) += meson/
obj-y += mvebu/
obj-y += nomadik/
obj-$(CONFIG_ARCH_NPCM7XX) += nuvoton/
@@ -69,9 +71,8 @@ obj-$(CONFIG_PINCTRL_SPEAR) += spear/
obj-y += sprd/
obj-$(CONFIG_PINCTRL_STM32) += stm32/
obj-$(CONFIG_PINCTRL_SUNXI) += sunxi/
+obj-$(CONFIG_ARCH_TEGRA) += tegra/
obj-y += ti/
obj-$(CONFIG_PINCTRL_UNIPHIER) += uniphier/
-obj-$(CONFIG_ARCH_VT8500) += vt8500/
-obj-y += mediatek/
-obj-y += cirrus/
obj-$(CONFIG_PINCTRL_VISCONTI) += visconti/
+obj-$(CONFIG_ARCH_VT8500) += vt8500/
Sort Kconfig and Makefile entries alphabetically for better maintenance in the future. While at it fix some style issues, such as: - "Say Y"/"Say yes"/"Say Yes" --> "Say Y" - "pullup/pulldown" --> "pull-up and pull-down" - wrong indentation Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> --- v3: fixed more grammar issues in AMD text v2: rebased on top of very recent pinctrl/devel (Linus), added some grammar fixes drivers/pinctrl/Kconfig | 469 +++++++++++++++++++-------------------- drivers/pinctrl/Makefile | 47 ++-- 2 files changed, 258 insertions(+), 258 deletions(-)