diff mbox series

[v4,2/2] arm64: dts: mediatek: add Kontron 3.5"-SBC-i1200

Message ID 20240408080816.4134370-2-mwalle@kernel.org (mailing list archive)
State New, archived
Headers show
Series [v4,1/2] dt-bindings: arm64: mediatek: add Kontron 3.5"-SBC-i1200 | expand

Commit Message

Michael Walle April 8, 2024, 8:08 a.m. UTC
Add basic support for the Kontron 3.5" single board computer featuring a
Mediatek i1200 SoC (MT8395/MT8195).

Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
---
v4:
- rebase to latest next

v3:
- add vsys regulator
- correct the LDO input of the mt6360 regulator
- add missing interrupt-cells
- no underscores in node names
- dropped regulator-compatible everywhere and use the correc node name
  instead
- reordered mmc0 properties
- split mmc1 pinctrl properties, add no-mmc
- removed all MTK_DRIVE_8mA
- add i2c0 and i2c1
- add comments for spi and i2c busses
- add firmware-name property for scp (this should probably go into the
  base dtsi?!)
- add missing tpm compatible
- renamed thermal zones to something more meaningful
- add correct bias-pull-up to (some) i2c busses
- moved reset handling into the PHY node, also added a compatible string
  for the PHY.

Mh, my memory is hazy, but IIRC I run into the same problem which was
discussed on netdev some time ago. That is, the PHY driver cannot be
probed unless it is taken out of reset. Which will only happen if you
probe it. And the workaround/advise was to use the compatible string in
that case, which is unfortunate.
Just wanted to point out, that it is *not* the same as snps,reset-*
because the latter will work just fine without the compatible. I'll
go with the compatible for now.

I did *not* add the vbus to the USB ports, not even on the front port.
That is because of:
  dependencies:
    connector: [ usb-role-switch ]
and we just have a simple USB3.2 USB-A connector, no dual roles. IMHO
that is a bug in the driver, which should handle the vbus supply as
optional.

v2:
- none
---
 arch/arm64/boot/dts/mediatek/Makefile         |    1 +
 .../mediatek/mt8395-kontron-3-5-sbc-i1200.dts | 1127 +++++++++++++++++
 2 files changed, 1128 insertions(+)
 create mode 100644 arch/arm64/boot/dts/mediatek/mt8395-kontron-3-5-sbc-i1200.dts
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index cae5fcc7ca0c..0072ed142550 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -78,5 +78,6 @@  dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-evb.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8365-evk.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8395-genio-1200-evk.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8390-genio-700-evk.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8395-kontron-3-5-sbc-i1200.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8395-radxa-nio-12l.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt8395-kontron-3-5-sbc-i1200.dts b/arch/arm64/boot/dts/mediatek/mt8395-kontron-3-5-sbc-i1200.dts
new file mode 100644
index 000000000000..e4b2af9489a8
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8395-kontron-3-5-sbc-i1200.dts
@@ -0,0 +1,1127 @@ 
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2024 Kontron Europe GmbH
+ *
+ * Author: Michael Walle <mwalle@kernel.org>
+ */
+/dts-v1/;
+
+#include "mt8195.dtsi"
+#include "mt6359.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/mt8195-pinfunc.h>
+#include <dt-bindings/regulator/mediatek,mt6360-regulator.h>
+#include <dt-bindings/spmi/spmi.h>
+
+/ {
+	model = "Kontron 3.5\"-SBC-i1200";
+	compatible = "kontron,3-5-sbc-i1200", "mediatek,mt8395", "mediatek,mt8195";
+
+	aliases {
+		mmc0 = &mmc0;
+		mmc1 = &mmc1;
+		serial0 = &uart1;
+		serial1 = &uart2;
+		serial2 = &uart3;
+		serial3 = &uart4;
+		serial4 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	firmware {
+		optee {
+			compatible = "linaro,optee-tz";
+			method = "smc";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_pins>;
+
+		key-0 {
+			gpios = <&pio 106 GPIO_ACTIVE_LOW>;
+			label = "volume_up";
+			linux,code = <KEY_VOLUMEUP>;
+			wakeup-source;
+			debounce-interval = <15>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pins>;
+
+		led-0 {
+			gpios = <&pio 107 GPIO_ACTIVE_HIGH>;
+			default-state = "keep";
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_GREEN>;
+		};
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0 0x40000000 0x0 0x80000000>;
+	};
+
+	vsys: regulator-vsys {
+		compatible = "regulator-fixed";
+		regulator-name = "vsys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/*
+		 * 12 MiB reserved for OP-TEE (BL32)
+		 * +-----------------------+ 0x43e0_0000
+		 * |      SHMEM 2MiB       |
+		 * +-----------------------+ 0x43c0_0000
+		 * |        | TA_RAM  8MiB |
+		 * + TZDRAM +--------------+ 0x4340_0000
+		 * |        | TEE_RAM 2MiB |
+		 * +-----------------------+ 0x4320_0000
+		 */
+		optee_reserved: optee@43200000 {
+			no-map;
+			reg = <0 0x43200000 0 0x00c00000>;
+		};
+
+		scp_mem: memory@50000000 {
+			compatible = "shared-dma-pool";
+			reg = <0 0x50000000 0 0x2900000>;
+			no-map;
+		};
+
+		vpu_mem: memory@53000000 {
+			compatible = "shared-dma-pool";
+			reg = <0 0x53000000 0 0x1400000>; /* 20 MB */
+		};
+
+		/* 2 MiB reserved for ARM Trusted Firmware (BL31) */
+		bl31_secmon_mem: memory@54600000 {
+			no-map;
+			reg = <0 0x54600000 0x0 0x200000>;
+		};
+
+		snd_dma_mem: memory@60000000 {
+			compatible = "shared-dma-pool";
+			reg = <0 0x60000000 0 0x1100000>;
+			no-map;
+		};
+
+		apu_mem: memory@62000000 {
+			compatible = "shared-dma-pool";
+			reg = <0 0x62000000 0 0x1400000>; /* 20 MB */
+		};
+	};
+
+	thermal_sensor0: thermal-sensor-0 {
+		compatible = "generic-adc-thermal";
+		#thermal-sensor-cells = <0>;
+		io-channels = <&auxadc 0>;
+		io-channel-names = "sensor-channel";
+		temperature-lookup-table = <(-25000) 1474
+					    (-20000) 1374
+					    (-15000) 1260
+					    (-10000) 1134
+					     (-5000) 1004
+						   0 874
+						5000 750
+					       10000 635
+					       15000 532
+					       20000 443
+					       25000 367
+					       30000 303
+					       35000 250
+					       40000 206
+					       45000 170
+					       50000 141
+					       55000 117
+					       60000 97
+					       65000 81
+					       70000 68
+					       75000 57
+					       80000 48
+					       85000 41
+					       90000 35
+					       95000 30
+					      100000 25
+					      105000 22
+					      110000 19
+					      115000 16
+					      120000 14
+					      125000 12
+					      130000 10
+					      135000 9
+					      140000 8
+					      145000 7
+					      150000 6>;
+	};
+
+	thermal_sensor1: thermal-sensor-1 {
+		compatible = "generic-adc-thermal";
+		#thermal-sensor-cells = <0>;
+		io-channels = <&auxadc 1>;
+		io-channel-names = "sensor-channel";
+		temperature-lookup-table = <(-25000) 1474
+					    (-20000) 1374
+					    (-15000) 1260
+					    (-10000) 1134
+					     (-5000) 1004
+						   0 874
+						5000 750
+					       10000 635
+					       15000 532
+					       20000 443
+					       25000 367
+					       30000 303
+					       35000 250
+					       40000 206
+					       45000 170
+					       50000 141
+					       55000 117
+					       60000 97
+					       65000 81
+					       70000 68
+					       75000 57
+					       80000 48
+					       85000 41
+					       90000 35
+					       95000 30
+					      100000 25
+					      105000 22
+					      110000 19
+					      115000 16
+					      120000 14
+					      125000 12
+					      130000 10
+					      135000 9
+					      140000 8
+					      145000 7
+					      150000 6>;
+	};
+
+	thermal_sensor2: thermal-sensor-2 {
+		compatible = "generic-adc-thermal";
+		#thermal-sensor-cells = <0>;
+		io-channels = <&auxadc 2>;
+		io-channel-names = "sensor-channel";
+		temperature-lookup-table = <(-25000) 1474
+					    (-20000) 1374
+					    (-15000) 1260
+					    (-10000) 1134
+					     (-5000) 1004
+						   0 874
+						5000 750
+					       10000 635
+					       15000 532
+					       20000 443
+					       25000 367
+					       30000 303
+					       35000 250
+					       40000 206
+					       45000 170
+					       50000 141
+					       55000 117
+					       60000 97
+					       65000 81
+					       70000 68
+					       75000 57
+					       80000 48
+					       85000 41
+					       90000 35
+					       95000 30
+					      100000 25
+					      105000 22
+					      110000 19
+					      115000 16
+					      120000 14
+					      125000 12
+					      130000 10
+					      135000 9
+					      140000 8
+					      145000 7
+					      150000 6>;
+	};
+};
+
+&auxadc {
+	status = "okay";
+};
+
+&eth {
+	phy-mode ="rgmii-id";
+	phy-handle = <&ethernet_phy0>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&eth_default_pins>;
+	pinctrl-1 = <&eth_sleep_pins>;
+	status = "okay";
+
+	mdio {
+		ethernet_phy0: ethernet-phy@1 {
+			compatible = "ethernet-phy-id001c.c916";
+			reg = <0x1>;
+			interrupts-extended = <&pio 94 IRQ_TYPE_LEVEL_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <80000>;
+			reset-gpios = <&pio 93 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&gpu {
+	status = "okay";
+	mali-supply = <&mt6315_7_vbuck1>;
+};
+
+/* CSI1/CSI2 connector */
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <100000>;
+	status = "okay";
+};
+
+/* CSI3 connector */
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
+	clock-frequency = <400000>;
+	status = "okay";
+
+	/* LVDS bridge @f */
+};
+
+/* Touch panel connector */
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c3_pins>;
+	clock-frequency = <100000>;
+	status = "okay";
+};
+
+/* B2B connector */
+&i2c4 {
+	clock-frequency = <100000>;
+	pinctrl-0 = <&i2c4_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&i2c6 {
+	clock-frequency = <400000>;
+	pinctrl-0 = <&i2c6_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	mt6360: pmic@34 {
+		compatible = "mediatek,mt6360";
+		reg = <0x34>;
+		interrupt-controller;
+		interrupts-extended = <&pio 101 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-names = "IRQB";
+		#interrupt-cells = <1>;
+
+		regulator {
+			compatible = "mediatek,mt6360-regulator";
+			LDO_VIN1-supply = <&vsys>;
+			LDO_VIN2-supply = <&vsys>;
+			LDO_VIN3-supply = <&vsys>;
+
+			mt6360_buck1: BUCK1 {
+				regulator-name = "emi_vdd2";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+							   MT6360_OPMODE_LP
+							   MT6360_OPMODE_ULP>;
+				regulator-always-on;
+			};
+
+			mt6360_buck2: BUCK2 {
+				regulator-name = "emi_vddq";
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+							   MT6360_OPMODE_LP
+							   MT6360_OPMODE_ULP>;
+				regulator-always-on;
+			};
+
+			mt6360_ldo1: LDO1 {
+				regulator-name = "mt6360_ldo1"; /* Test point */
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <3600000>;
+				regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+							   MT6360_OPMODE_LP>;
+			};
+
+			mt6360_ldo2: LDO2 {
+				regulator-name = "panel1_p1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+							   MT6360_OPMODE_LP>;
+			};
+
+			mt6360_ldo3: LDO3 {
+				regulator-name = "vmc_pmu";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+							   MT6360_OPMODE_LP>;
+			};
+
+			mt6360_ldo5: LDO5 {
+				regulator-name = "vmch_pmu";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+							   MT6360_OPMODE_LP>;
+			};
+
+			mt6360_ldo6: LDO6 {
+				regulator-name = "mt6360_ldo6"; /* Test point */
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <2100000>;
+				regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+							   MT6360_OPMODE_LP>;
+			};
+
+			mt6360_ldo7: LDO7 {
+				regulator-name = "emi_vmddr_en";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+							   MT6360_OPMODE_LP>;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&mmc0 {
+	pinctrl-names = "default", "state_uhs";
+	pinctrl-0 = <&mmc0_default_pins>;
+	pinctrl-1 = <&mmc0_uhs_pins>;
+	bus-width = <8>;
+	max-frequency = <200000000>;
+	hs400-ds-delay = <0x14c11>;
+	cap-mmc-highspeed;
+	cap-mmc-hw-reset;
+	mmc-hs200-1_8v;
+	mmc-hs400-1_8v;
+	no-sdio;
+	no-sd;
+	non-removable;
+	vmmc-supply = <&mt6359_vemc_1_ldo_reg>;
+	vqmmc-supply = <&mt6359_vufs_ldo_reg>;
+	status = "okay";
+};
+
+&mmc1 {
+	pinctrl-names = "default", "state_uhs";
+	pinctrl-0 = <&mmc1_default_pins>, <&mmc1_detect_pins>;
+	pinctrl-1 = <&mmc1_default_pins>;
+	cd-gpios = <&pio 129 GPIO_ACTIVE_LOW>;
+	bus-width = <4>;
+	max-frequency = <200000000>;
+	cap-sd-highspeed;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	no-mmc;
+	vmmc-supply = <&mt6360_ldo5>;
+	vqmmc-supply = <&mt6360_ldo3>;
+	status = "okay";
+};
+
+&mt6359_vbbck_ldo_reg {
+	regulator-always-on;
+};
+
+&mt6359_vcore_buck_reg {
+	regulator-always-on;
+};
+
+&mt6359_vgpu11_buck_reg {
+	regulator-always-on;
+};
+
+&mt6359_vproc1_buck_reg {
+	regulator-always-on;
+};
+
+&mt6359_vproc2_buck_reg {
+	regulator-always-on;
+};
+
+&mt6359_vpu_buck_reg {
+	regulator-always-on;
+};
+
+&mt6359_vrf12_ldo_reg {
+	regulator-always-on;
+};
+
+&mt6359_vsram_md_ldo_reg {
+	regulator-always-on;
+};
+
+&mt6359_vsram_others_ldo_reg {
+	regulator-always-on;
+};
+
+&nor_flash {
+	pinctrl-names = "default";
+	pinctrl-0 = <&nor_pins_default>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <52000000>;
+		spi-rx-bus-width = <2>;
+		spi-tx-bus-width = <2>;
+	};
+};
+
+&pcie0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie0_pins_default>;
+	status = "okay";
+};
+
+&pcie1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie1_pins_default>;
+	status = "okay";
+};
+
+&pciephy {
+	status = "okay";
+};
+
+&pio {
+	eth_default_pins: eth-default-pins {
+		pins-txd {
+			pinmux = <PINMUX_GPIO77__FUNC_GBE_TXD3>,
+				 <PINMUX_GPIO78__FUNC_GBE_TXD2>,
+				 <PINMUX_GPIO79__FUNC_GBE_TXD1>,
+				 <PINMUX_GPIO80__FUNC_GBE_TXD0>;
+			drive-strength = <8>;
+		};
+
+		pins-rxd {
+			pinmux = <PINMUX_GPIO81__FUNC_GBE_RXD3>,
+				 <PINMUX_GPIO82__FUNC_GBE_RXD2>,
+				 <PINMUX_GPIO83__FUNC_GBE_RXD1>,
+				 <PINMUX_GPIO84__FUNC_GBE_RXD0>;
+		};
+
+		pins-cc {
+			pinmux = <PINMUX_GPIO85__FUNC_GBE_TXC>,
+				 <PINMUX_GPIO86__FUNC_GBE_RXC>,
+				 <PINMUX_GPIO87__FUNC_GBE_RXDV>,
+				 <PINMUX_GPIO88__FUNC_GBE_TXEN>;
+			drive-strength = <8>;
+		};
+
+		pins-mdio {
+			pinmux = <PINMUX_GPIO89__FUNC_GBE_MDC>,
+				 <PINMUX_GPIO90__FUNC_GBE_MDIO>;
+			input-enable;
+		};
+
+		pins-power {
+			pinmux = <PINMUX_GPIO91__FUNC_GPIO91>,
+				 <PINMUX_GPIO92__FUNC_GPIO92>;
+			output-high;
+		};
+
+		pins-reset {
+			pinmux = <PINMUX_GPIO93__FUNC_GPIO93>;
+			output-high;
+		};
+
+		pins-interrupt {
+			pinmux = <PINMUX_GPIO94__FUNC_GPIO94>;
+			input-enable;
+		};
+	};
+
+	eth_sleep_pins: eth-sleep-pins {
+		pins-txd {
+			pinmux = <PINMUX_GPIO77__FUNC_GPIO77>,
+				 <PINMUX_GPIO78__FUNC_GPIO78>,
+				 <PINMUX_GPIO79__FUNC_GPIO79>,
+				 <PINMUX_GPIO80__FUNC_GPIO80>;
+		};
+
+		pins-cc {
+			pinmux = <PINMUX_GPIO85__FUNC_GPIO85>,
+				 <PINMUX_GPIO88__FUNC_GPIO88>,
+				 <PINMUX_GPIO87__FUNC_GPIO87>,
+				 <PINMUX_GPIO86__FUNC_GPIO86>;
+		};
+
+		pins-rxd {
+			pinmux = <PINMUX_GPIO81__FUNC_GPIO81>,
+				 <PINMUX_GPIO82__FUNC_GPIO82>,
+				 <PINMUX_GPIO83__FUNC_GPIO83>,
+				 <PINMUX_GPIO84__FUNC_GPIO84>;
+		};
+
+		pins-mdio {
+			pinmux = <PINMUX_GPIO89__FUNC_GPIO89>,
+				 <PINMUX_GPIO90__FUNC_GPIO90>;
+			input-disable;
+			bias-disable;
+		};
+	};
+
+	gpio_keys_pins: gpio-keys-pins {
+		pins {
+			pinmux = <PINMUX_GPIO106__FUNC_GPIO106>;
+			input-enable;
+		};
+	};
+
+	i2c0_pins: i2c0-pins {
+		pins {
+			pinmux = <PINMUX_GPIO8__FUNC_SDA0>,
+				 <PINMUX_GPIO9__FUNC_SCL0>;
+			bias-pull-up = <MTK_PULL_SET_RSEL_111>;
+			drive-strength-microamp = <1000>;
+		};
+	};
+
+	i2c1_pins: i2c1-pins {
+		pins {
+			pinmux = <PINMUX_GPIO10__FUNC_SDA1>,
+				 <PINMUX_GPIO11__FUNC_SCL1>;
+			bias-pull-up = <MTK_PULL_SET_RSEL_111>;
+			drive-strength-microamp = <1000>;
+		};
+	};
+
+	i2c2_pins: i2c2-default-pins {
+		pins-bus {
+			pinmux = <PINMUX_GPIO12__FUNC_SDA2>,
+				 <PINMUX_GPIO13__FUNC_SCL2>;
+			bias-pull-up = <MTK_PULL_SET_RSEL_111>;
+			drive-strength-microamp = <1000>;
+		};
+	};
+
+	i2c3_pins: i2c3-pins {
+		pins {
+			pinmux = <PINMUX_GPIO14__FUNC_SDA3>,
+				 <PINMUX_GPIO15__FUNC_SCL3>;
+			bias-pull-up = <MTK_PULL_SET_RSEL_111>;
+			drive-strength-microamp = <1000>;
+		};
+	};
+
+	i2c4_pins: i2c4-pins {
+		pins {
+			pinmux = <PINMUX_GPIO16__FUNC_SDA4>,
+				 <PINMUX_GPIO17__FUNC_SCL4>;
+			bias-pull-up = <MTK_PULL_SET_RSEL_111>;
+			drive-strength-microamp = <1000>;
+		};
+	};
+
+	i2c6_pins: i2c6-pins {
+		pins {
+			pinmux = <PINMUX_GPIO25__FUNC_SDA6>,
+				 <PINMUX_GPIO26__FUNC_SCL6>;
+			bias-pull-up;
+			drive-strength-microamp = <1000>;
+		};
+	};
+
+	mmc0_default_pins: mmc0-default-pins {
+		pins-clk {
+			pinmux = <PINMUX_GPIO122__FUNC_MSDC0_CLK>;
+			drive-strength = <6>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+		};
+
+		pins-cmd-dat {
+			pinmux = <PINMUX_GPIO126__FUNC_MSDC0_DAT0>,
+				 <PINMUX_GPIO125__FUNC_MSDC0_DAT1>,
+				 <PINMUX_GPIO124__FUNC_MSDC0_DAT2>,
+				 <PINMUX_GPIO123__FUNC_MSDC0_DAT3>,
+				 <PINMUX_GPIO119__FUNC_MSDC0_DAT4>,
+				 <PINMUX_GPIO118__FUNC_MSDC0_DAT5>,
+				 <PINMUX_GPIO117__FUNC_MSDC0_DAT6>,
+				 <PINMUX_GPIO116__FUNC_MSDC0_DAT7>,
+				 <PINMUX_GPIO121__FUNC_MSDC0_CMD>;
+			input-enable;
+			drive-strength = <6>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+
+		pins-rst {
+			pinmux = <PINMUX_GPIO120__FUNC_MSDC0_RSTB>;
+			drive-strength = <6>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+	};
+
+	mmc0_uhs_pins: mmc0-uhs-pins {
+		pins-clk {
+			pinmux = <PINMUX_GPIO122__FUNC_MSDC0_CLK>;
+			drive-strength = <8>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+		};
+
+		pins-cmd-dat {
+			pinmux = <PINMUX_GPIO126__FUNC_MSDC0_DAT0>,
+				 <PINMUX_GPIO125__FUNC_MSDC0_DAT1>,
+				 <PINMUX_GPIO124__FUNC_MSDC0_DAT2>,
+				 <PINMUX_GPIO123__FUNC_MSDC0_DAT3>,
+				 <PINMUX_GPIO119__FUNC_MSDC0_DAT4>,
+				 <PINMUX_GPIO118__FUNC_MSDC0_DAT5>,
+				 <PINMUX_GPIO117__FUNC_MSDC0_DAT6>,
+				 <PINMUX_GPIO116__FUNC_MSDC0_DAT7>,
+				 <PINMUX_GPIO121__FUNC_MSDC0_CMD>;
+			input-enable;
+			drive-strength = <8>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+
+		pins-ds {
+			pinmux = <PINMUX_GPIO127__FUNC_MSDC0_DSL>;
+			drive-strength = <8>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+		};
+
+		pins-rst {
+			pinmux = <PINMUX_GPIO120__FUNC_MSDC0_RSTB>;
+			drive-strength = <8>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+	};
+
+	mmc1_default_pins: mmc1-default-pins {
+		pins-clk {
+			pinmux = <PINMUX_GPIO111__FUNC_MSDC1_CLK>;
+			drive-strength = <8>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+		};
+
+		pins-cmd-dat {
+			pinmux = <PINMUX_GPIO110__FUNC_MSDC1_CMD>,
+				 <PINMUX_GPIO112__FUNC_MSDC1_DAT0>,
+				 <PINMUX_GPIO113__FUNC_MSDC1_DAT1>,
+				 <PINMUX_GPIO114__FUNC_MSDC1_DAT2>,
+				 <PINMUX_GPIO115__FUNC_MSDC1_DAT3>;
+			input-enable;
+			drive-strength = <8>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+	};
+
+	mmc1_detect_pins: mmc1-detect-pins {
+		pins-insert {
+			pinmux = <PINMUX_GPIO129__FUNC_GPIO129>;
+			bias-pull-up;
+		};
+	};
+
+	nor_pins_default: nor-default-pins {
+		pins-ck-io {
+			pinmux = <PINMUX_GPIO142__FUNC_SPINOR_IO0>,
+				 <PINMUX_GPIO141__FUNC_SPINOR_CK>,
+				 <PINMUX_GPIO143__FUNC_SPINOR_IO1>;
+			drive-strength = <6>;
+			bias-pull-down;
+		};
+
+		pins-cs {
+			pinmux = <PINMUX_GPIO140__FUNC_SPINOR_CS>;
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+	};
+
+	pcie0_pins_default: pcie0-default-pins {
+		pins-bus {
+			pinmux = <PINMUX_GPIO19__FUNC_WAKEN>,
+				 <PINMUX_GPIO20__FUNC_PERSTN>,
+				 <PINMUX_GPIO21__FUNC_CLKREQN>;
+			bias-pull-up;
+		};
+	};
+
+	pcie1_pins_default: pcie1-default-pins {
+		pins-bus {
+			pinmux = <PINMUX_GPIO0__FUNC_PERSTN_1>,
+				 <PINMUX_GPIO1__FUNC_CLKREQN_1>,
+				 <PINMUX_GPIO2__FUNC_WAKEN_1>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+	};
+
+	led_pins: led-pins {
+		pins-power-en {
+			pinmux = <PINMUX_GPIO107__FUNC_GPIO107>;
+			output-high;
+		};
+	};
+
+	spi0_pins: spi0-default-pins {
+		pins-cs-mosi-clk {
+			pinmux = <PINMUX_GPIO132__FUNC_SPIM0_CSB>,
+				 <PINMUX_GPIO134__FUNC_SPIM0_MO>,
+				 <PINMUX_GPIO133__FUNC_SPIM0_CLK>;
+			bias-disable;
+		};
+
+		pins-miso {
+			pinmux = <PINMUX_GPIO135__FUNC_SPIM0_MI>;
+			bias-pull-down;
+		};
+	};
+
+	spi1_pins: spi1-default-pins {
+		pins-cs-mosi-clk {
+			pinmux = <PINMUX_GPIO136__FUNC_SPIM1_CSB>,
+				 <PINMUX_GPIO138__FUNC_SPIM1_MO>,
+				 <PINMUX_GPIO137__FUNC_SPIM1_CLK>;
+			bias-disable;
+		};
+
+		pins-miso {
+			pinmux = <PINMUX_GPIO139__FUNC_SPIM1_MI>;
+			bias-pull-down;
+		};
+	};
+
+	uart0_pins: uart0-pins {
+		pins-rx {
+			pinmux = <PINMUX_GPIO99__FUNC_URXD0>;
+			input-enable;
+			bias-pull-up;
+		};
+
+		pins-tx {
+			pinmux = <PINMUX_GPIO98__FUNC_UTXD0>;
+		};
+	};
+
+	uart1_pins: uart1-pins {
+		pins-rx {
+			pinmux = <PINMUX_GPIO103__FUNC_URXD1>;
+			input-enable;
+			bias-pull-up;
+		};
+
+		pins-tx {
+			pinmux = <PINMUX_GPIO102__FUNC_UTXD1>;
+		};
+
+		pins-rts {
+			pinmux = <PINMUX_GPIO100__FUNC_URTS1>;
+		};
+
+		pins-cts {
+			pinmux = <PINMUX_GPIO101__FUNC_UCTS1>;
+			input-enable;
+		};
+	};
+
+	uart2_pins: uart2-pins {
+		pins-rx {
+			pinmux = <PINMUX_GPIO68__FUNC_URXD2>;
+			input-enable;
+			bias-pull-up;
+		};
+
+		pins-tx {
+			pinmux = <PINMUX_GPIO67__FUNC_UTXD2>;
+		};
+
+		pins-rts {
+			pinmux = <PINMUX_GPIO66__FUNC_URTS2>;
+		};
+
+		pins-cts {
+			pinmux = <PINMUX_GPIO65__FUNC_UCTS2>;
+			input-enable;
+		};
+	};
+
+	uart3_pins: uart3-pins {
+		pins-rx {
+			pinmux = <PINMUX_GPIO5__FUNC_URXD3>;
+			input-enable;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+
+		pins-tx {
+			pinmux = <PINMUX_GPIO4__FUNC_UTXD3>;
+		};
+	};
+
+	uart4_pins: uart4-pins {
+		pins-rx {
+			pinmux = <PINMUX_GPIO7__FUNC_URXD4>;
+			input-enable;
+			bias-pull-up;
+		};
+
+		pins-tx {
+			pinmux = <PINMUX_GPIO6__FUNC_UTXD4>;
+		};
+	};
+};
+
+&pmic {
+	interrupts-extended = <&pio 222 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&scp {
+	memory-region = <&scp_mem>;
+	firmware-name = "mediatek/mt8195/scp.img";
+	status = "okay";
+};
+
+&spmi {
+	#address-cells = <2>;
+	#size-cells = <0>;
+
+	mt6315@6 {
+		compatible = "mediatek,mt6315-regulator";
+		reg = <0x6 SPMI_USID>;
+
+		regulators {
+			mt6315_6_vbuck1: vbuck1 {
+				regulator-name = "Vbcpu";
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1193750>;
+				regulator-enable-ramp-delay = <256>;
+				regulator-ramp-delay = <6250>;
+				regulator-allowed-modes = <0 1 2>;
+				regulator-always-on;
+			};
+		};
+	};
+
+	mt6315@7 {
+		compatible = "mediatek,mt6315-regulator";
+		reg = <0x7 SPMI_USID>;
+
+		regulators {
+			mt6315_7_vbuck1: vbuck1 {
+				regulator-name = "Vgpu";
+				regulator-min-microvolt = <625000>;
+				regulator-max-microvolt = <1193750>;
+				regulator-enable-ramp-delay = <256>;
+				regulator-ramp-delay = <6250>;
+				regulator-allowed-modes = <0 1 2>;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+/* USB3.2 front port */
+&ssusb0 {
+	dr_mode = "host";
+	vusb33-supply = <&mt6359_vusb_ldo_reg>;
+	status = "okay";
+};
+
+/* USB2.0 M.2 Key-E */
+&ssusb2 {
+	vusb33-supply = <&mt6359_vusb_ldo_reg>;
+	status = "okay";
+};
+
+/* USB2.0 to on-board usb hub */
+&ssusb3 {
+	vusb33-supply = <&mt6359_vusb_ldo_reg>;
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins>;
+	mediatek,pad-select = <0>;
+	status = "okay";
+
+	tpm: tpm@0 {
+		compatible = "infineon,slb9670", "tcg,tpm_tis-spi";
+		reg = <0>;
+		spi-max-frequency = <18500000>;
+	};
+};
+
+/* B2B connector */
+&spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi1_pins>;
+	mediatek,pad-select = <0>;
+	status = "okay";
+};
+
+&thermal_zones {
+	cpu-thermal {
+		polling-delay = <1000>; /* milliseconds */
+		polling-delay-passive = <0>; /* milliseconds */
+		thermal-sensors = <&thermal_sensor0>;
+
+		trips {
+			trip-alert {
+				temperature = <85000>;
+				hysteresis = <2000>;
+				type = "passive";
+			};
+
+			trip-crit {
+				temperature = <95000>;
+				hysteresis = <2000>;
+				type = "critical";
+			};
+		};
+	};
+
+	pcb-top-thermal {
+		polling-delay = <1000>; /* milliseconds */
+		polling-delay-passive = <0>; /* milliseconds */
+		thermal-sensors = <&thermal_sensor1>;
+
+		trips {
+			trip-alert {
+				temperature = <75000>;
+				hysteresis = <2000>;
+				type = "passive";
+			};
+
+			trip-crit {
+				temperature = <85000>;
+				hysteresis = <2000>;
+				type = "critical";
+			};
+		};
+	};
+
+	pcb-bottom-thermal {
+		polling-delay = <1000>; /* milliseconds */
+		polling-delay-passive = <0>; /* milliseconds */
+		thermal-sensors = <&thermal_sensor2>;
+
+		trips {
+			trip-alert {
+				temperature = <75000>;
+				hysteresis = <2000>;
+				type = "passive";
+			};
+
+			trip-crit {
+				temperature = <85000>;
+				hysteresis = <2000>;
+				type = "critical";
+			};
+		};
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins>;
+	status = "okay";
+};
+
+/* USB3 */
+&u3phy0 {
+	status = "okay";
+};
+
+/* PCIe1/USB2 */
+&u3phy1 {
+	status = "okay";
+};
+
+/* USB2 */
+&u3phy2 {
+	status = "okay";
+};
+
+/* USB2 */
+&u3phy3 {
+	status = "okay";
+};
+
+/* USB3.2 front port */
+&xhci0 {
+	status = "okay";
+};
+
+/* USB2.0 M.2 Key-B */
+&xhci1 {
+	vusb33-supply = <&mt6359_vusb_ldo_reg>;
+	mediatek,u3p-dis-msk = <0x01>;
+	status = "okay";
+};
+
+/* USB2.0 M.2 Key-E */
+&xhci2 {
+	status = "okay";
+};
+
+/* USB2.0 to on-board usb hub */
+&xhci3 {
+	status = "okay";
+};