@@ -19,6 +19,8 @@ config NET_MEDIATEK_SOC
select DIMLIB
select PAGE_POOL
select PAGE_POOL_STATS
+ select PCS_MTK_LYNXI
+ select REGMAP_MMIO
help
This driver supports the gigabit ethernet MACs in the
MediaTek SoC family.
@@ -4079,6 +4079,7 @@ static int mtk_unreg_dev(struct mtk_eth *eth)
static int mtk_cleanup(struct mtk_eth *eth)
{
+ mtk_sgmii_destroy(eth->sgmii);
mtk_unreg_dev(eth);
mtk_free_dev(eth);
cancel_work_sync(ð->pending_work);
@@ -4582,6 +4583,7 @@ static int mtk_probe(struct platform_device *pdev)
if (!eth->sgmii)
return -ENOMEM;
+ eth->sgmii->dev = eth->dev;
err = mtk_sgmii_init(eth->sgmii, pdev->dev.of_node,
eth->soc->ana_rgc3);
@@ -4594,14 +4596,17 @@ static int mtk_probe(struct platform_device *pdev)
"mediatek,pctl");
if (IS_ERR(eth->pctl)) {
dev_err(&pdev->dev, "no pctl regmap found\n");
- return PTR_ERR(eth->pctl);
+ err = PTR_ERR(eth->pctl);
+ goto err_destroy_sgmii;
}
}
if (MTK_HAS_CAPS(eth->soc->caps, MTK_NETSYS_V2)) {
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- if (!res)
- return -EINVAL;
+ if (!res) {
+ err = -EINVAL;
+ goto err_destroy_sgmii;
+ }
}
if (eth->soc->offload_version) {
@@ -4751,6 +4756,8 @@ static int mtk_probe(struct platform_device *pdev)
return 0;
+err_destroy_sgmii:
+ mtk_sgmii_destroy(eth->sgmii);
err_deinit_ppe:
mtk_ppe_deinit(eth);
mtk_mdio_cleanup(eth);
@@ -510,65 +510,6 @@
#define ETHSYS_DMA_AG_MAP_QDMA BIT(1)
#define ETHSYS_DMA_AG_MAP_PPE BIT(2)
-/* SGMII subsystem config registers */
-/* BMCR (low 16) BMSR (high 16) */
-#define SGMSYS_PCS_CONTROL_1 0x0
-#define SGMII_BMCR GENMASK(15, 0)
-#define SGMII_BMSR GENMASK(31, 16)
-#define SGMII_AN_RESTART BIT(9)
-#define SGMII_ISOLATE BIT(10)
-#define SGMII_AN_ENABLE BIT(12)
-#define SGMII_LINK_STATYS BIT(18)
-#define SGMII_AN_ABILITY BIT(19)
-#define SGMII_AN_COMPLETE BIT(21)
-#define SGMII_PCS_FAULT BIT(23)
-#define SGMII_AN_EXPANSION_CLR BIT(30)
-
-#define SGMSYS_PCS_ADVERTISE 0x8
-#define SGMII_ADVERTISE GENMASK(15, 0)
-#define SGMII_LPA GENMASK(31, 16)
-
-/* Register to programmable link timer, the unit in 2 * 8ns */
-#define SGMSYS_PCS_LINK_TIMER 0x18
-#define SGMII_LINK_TIMER_MASK GENMASK(19, 0)
-#define SGMII_LINK_TIMER_DEFAULT (0x186a0 & SGMII_LINK_TIMER_MASK)
-
-/* Register to control remote fault */
-#define SGMSYS_SGMII_MODE 0x20
-#define SGMII_IF_MODE_SGMII BIT(0)
-#define SGMII_SPEED_DUPLEX_AN BIT(1)
-#define SGMII_SPEED_MASK GENMASK(3, 2)
-#define SGMII_SPEED_10 FIELD_PREP(SGMII_SPEED_MASK, 0)
-#define SGMII_SPEED_100 FIELD_PREP(SGMII_SPEED_MASK, 1)
-#define SGMII_SPEED_1000 FIELD_PREP(SGMII_SPEED_MASK, 2)
-#define SGMII_DUPLEX_HALF BIT(4)
-#define SGMII_IF_MODE_BIT5 BIT(5)
-#define SGMII_REMOTE_FAULT_DIS BIT(8)
-#define SGMII_CODE_SYNC_SET_VAL BIT(9)
-#define SGMII_CODE_SYNC_SET_EN BIT(10)
-#define SGMII_SEND_AN_ERROR_EN BIT(11)
-#define SGMII_IF_MODE_MASK GENMASK(5, 1)
-
-/* Register to reset SGMII design */
-#define SGMII_RESERVED_0 0x34
-#define SGMII_SW_RESET BIT(0)
-
-/* Register to set SGMII speed, ANA RG_ Control Signals III*/
-#define SGMSYS_ANA_RG_CS3 0x2028
-#define RG_PHY_SPEED_MASK (BIT(2) | BIT(3))
-#define RG_PHY_SPEED_1_25G 0x0
-#define RG_PHY_SPEED_3_125G BIT(2)
-
-/* Register to power up QPHY */
-#define SGMSYS_QPHY_PWR_STATE_CTRL 0xe8
-#define SGMII_PHYA_PWD BIT(4)
-
-/* Register to QPHY wrapper control */
-#define SGMSYS_QPHY_WRAP_CTRL 0xec
-#define SGMII_PN_SWAP_MASK GENMASK(1, 0)
-#define SGMII_PN_SWAP_TX_RX (BIT(0) | BIT(1))
-#define MTK_SGMII_FLAG_PN_SWAP BIT(0)
-
/* Infrasys subsystem config registers */
#define INFRA_MISC2 0x70c
#define CO_QPHY_SEL BIT(0)
@@ -1103,29 +1044,13 @@ struct mtk_soc_data {
/* currently no SoC has more than 2 macs */
#define MTK_MAX_DEVS 2
-/* struct mtk_pcs - This structure holds each sgmii regmap and associated
- * data
- * @regmap: The register map pointing at the range used to setup
- * SGMII modes
- * @ana_rgc3: The offset refers to register ANA_RGC3 related to regmap
- * @interface: Currently configured interface mode
- * @pcs: Phylink PCS structure
- * @flags: Flags indicating hardware properties
- */
-struct mtk_pcs {
- struct regmap *regmap;
- u32 ana_rgc3;
- phy_interface_t interface;
- struct phylink_pcs pcs;
- u32 flags;
-};
-
/* struct mtk_sgmii - This is the structure holding sgmii regmap and its
* characteristics
* @pcs Array of individual PCS structures
*/
struct mtk_sgmii {
- struct mtk_pcs pcs[MTK_MAX_DEVS];
+ struct phylink_pcs *pcs[MTK_MAX_DEVS];
+ struct device *dev;
};
/* struct mtk_eth - This is the main datasructure for holding the state
@@ -1353,6 +1278,7 @@ u32 mtk_r32(struct mtk_eth *eth, unsigned reg);
struct phylink_pcs *mtk_sgmii_select_pcs(struct mtk_sgmii *ss, int id);
int mtk_sgmii_init(struct mtk_sgmii *ss, struct device_node *np,
u32 ana_rgc3);
+void mtk_sgmii_destroy(struct mtk_sgmii *ss);
int mtk_gmac_sgmii_path_setup(struct mtk_eth *eth, int mac_id);
int mtk_gmac_gephy_path_setup(struct mtk_eth *eth, int mac_id);
@@ -10,178 +10,16 @@
#include <linux/mfd/syscon.h>
#include <linux/of.h>
#include <linux/phylink.h>
+#include <linux/pcs/pcs-mtk-lynxi.h>
#include <linux/regmap.h>
#include "mtk_eth_soc.h"
-static struct mtk_pcs *pcs_to_mtk_pcs(struct phylink_pcs *pcs)
-{
- return container_of(pcs, struct mtk_pcs, pcs);
-}
-
-static void mtk_pcs_get_state(struct phylink_pcs *pcs,
- struct phylink_link_state *state)
-{
- struct mtk_pcs *mpcs = pcs_to_mtk_pcs(pcs);
- unsigned int bm, adv;
-
- /* Read the BMSR and LPA */
- regmap_read(mpcs->regmap, SGMSYS_PCS_CONTROL_1, &bm);
- regmap_read(mpcs->regmap, SGMSYS_PCS_ADVERTISE, &adv);
-
- phylink_mii_c22_pcs_decode_state(state, FIELD_GET(SGMII_BMSR, bm),
- FIELD_GET(SGMII_LPA, adv));
-}
-
-static int mtk_pcs_config(struct phylink_pcs *pcs, unsigned int mode,
- phy_interface_t interface,
- const unsigned long *advertising,
- bool permit_pause_to_mac)
-{
- bool mode_changed = false, changed, use_an;
- struct mtk_pcs *mpcs = pcs_to_mtk_pcs(pcs);
- unsigned int rgc3, sgm_mode, bmcr;
- int advertise, link_timer;
-
- advertise = phylink_mii_c22_pcs_encode_advertisement(interface,
- advertising);
- if (advertise < 0)
- return advertise;
-
- /* Clearing IF_MODE_BIT0 switches the PCS to BASE-X mode, and
- * we assume that fixes it's speed at bitrate = line rate (in
- * other words, 1000Mbps or 2500Mbps).
- */
- if (interface == PHY_INTERFACE_MODE_SGMII) {
- sgm_mode = SGMII_IF_MODE_SGMII;
- if (phylink_autoneg_inband(mode)) {
- sgm_mode |= SGMII_REMOTE_FAULT_DIS |
- SGMII_SPEED_DUPLEX_AN;
- use_an = true;
- } else {
- use_an = false;
- }
- } else if (phylink_autoneg_inband(mode)) {
- /* 1000base-X or 2500base-X autoneg */
- sgm_mode = SGMII_REMOTE_FAULT_DIS;
- use_an = linkmode_test_bit(ETHTOOL_LINK_MODE_Autoneg_BIT,
- advertising);
- } else {
- /* 1000base-X or 2500base-X without autoneg */
- sgm_mode = 0;
- use_an = false;
- }
-
- if (use_an) {
- bmcr = SGMII_AN_ENABLE;
- } else {
- bmcr = 0;
- }
-
- if (mpcs->interface != interface) {
- link_timer = phylink_get_link_timer_ns(interface);
- if (link_timer < 0)
- return link_timer;
-
- /* PHYA power down */
- regmap_update_bits(mpcs->regmap, SGMSYS_QPHY_PWR_STATE_CTRL,
- SGMII_PHYA_PWD, SGMII_PHYA_PWD);
-
- /* Reset SGMII PCS state */
- regmap_update_bits(mpcs->regmap, SGMII_RESERVED_0,
- SGMII_SW_RESET, SGMII_SW_RESET);
-
- if (mpcs->flags & MTK_SGMII_FLAG_PN_SWAP)
- regmap_update_bits(mpcs->regmap, SGMSYS_QPHY_WRAP_CTRL,
- SGMII_PN_SWAP_MASK,
- SGMII_PN_SWAP_TX_RX);
-
- if (interface == PHY_INTERFACE_MODE_2500BASEX)
- rgc3 = RG_PHY_SPEED_3_125G;
- else
- rgc3 = 0;
-
- /* Configure the underlying interface speed */
- regmap_update_bits(mpcs->regmap, mpcs->ana_rgc3,
- RG_PHY_SPEED_3_125G, rgc3);
-
- /* Setup the link timer */
- regmap_write(mpcs->regmap, SGMSYS_PCS_LINK_TIMER, link_timer / 2 / 8);
-
- mpcs->interface = interface;
- mode_changed = true;
- }
-
- /* Update the advertisement, noting whether it has changed */
- regmap_update_bits_check(mpcs->regmap, SGMSYS_PCS_ADVERTISE,
- SGMII_ADVERTISE, advertise, &changed);
-
- /* Update the sgmsys mode register */
- regmap_update_bits(mpcs->regmap, SGMSYS_SGMII_MODE,
- SGMII_REMOTE_FAULT_DIS | SGMII_SPEED_DUPLEX_AN |
- SGMII_IF_MODE_SGMII, sgm_mode);
-
- /* Update the BMCR */
- regmap_update_bits(mpcs->regmap, SGMSYS_PCS_CONTROL_1,
- SGMII_AN_ENABLE, bmcr);
-
- /* Release PHYA power down state
- * Only removing bit SGMII_PHYA_PWD isn't enough.
- * There are cases when the SGMII_PHYA_PWD register contains 0x9 which
- * prevents SGMII from working. The SGMII still shows link but no traffic
- * can flow. Writing 0x0 to the PHYA_PWD register fix the issue. 0x0 was
- * taken from a good working state of the SGMII interface.
- * Unknown how much the QPHY needs but it is racy without a sleep.
- * Tested on mt7622 & mt7986.
- */
- usleep_range(50, 100);
- regmap_write(mpcs->regmap, SGMSYS_QPHY_PWR_STATE_CTRL, 0);
-
- return changed || mode_changed;
-}
-
-static void mtk_pcs_restart_an(struct phylink_pcs *pcs)
-{
- struct mtk_pcs *mpcs = pcs_to_mtk_pcs(pcs);
-
- regmap_update_bits(mpcs->regmap, SGMSYS_PCS_CONTROL_1,
- SGMII_AN_RESTART, SGMII_AN_RESTART);
-}
-
-static void mtk_pcs_link_up(struct phylink_pcs *pcs, unsigned int mode,
- phy_interface_t interface, int speed, int duplex)
-{
- struct mtk_pcs *mpcs = pcs_to_mtk_pcs(pcs);
- unsigned int sgm_mode;
-
- if (!phylink_autoneg_inband(mode)) {
- /* Force the speed and duplex setting */
- if (speed == SPEED_10)
- sgm_mode = SGMII_SPEED_10;
- else if (speed == SPEED_100)
- sgm_mode = SGMII_SPEED_100;
- else
- sgm_mode = SGMII_SPEED_1000;
-
- if (duplex != DUPLEX_FULL)
- sgm_mode |= SGMII_DUPLEX_HALF;
-
- regmap_update_bits(mpcs->regmap, SGMSYS_SGMII_MODE,
- SGMII_DUPLEX_HALF | SGMII_SPEED_MASK,
- sgm_mode);
- }
-}
-
-static const struct phylink_pcs_ops mtk_pcs_ops = {
- .pcs_get_state = mtk_pcs_get_state,
- .pcs_config = mtk_pcs_config,
- .pcs_an_restart = mtk_pcs_restart_an,
- .pcs_link_up = mtk_pcs_link_up,
-};
-
int mtk_sgmii_init(struct mtk_sgmii *ss, struct device_node *r, u32 ana_rgc3)
{
struct device_node *np;
+ struct regmap *regmap;
+ u32 flags;
int i;
for (i = 0; i < MTK_MAX_DEVS; i++) {
@@ -189,20 +27,18 @@ int mtk_sgmii_init(struct mtk_sgmii *ss, struct device_node *r, u32 ana_rgc3)
if (!np)
break;
- ss->pcs[i].ana_rgc3 = ana_rgc3;
- ss->pcs[i].regmap = syscon_node_to_regmap(np);
-
- ss->pcs[i].flags = 0;
+ regmap = syscon_node_to_regmap(np);
+ flags = 0;
if (of_property_read_bool(np, "mediatek,pnswap"))
- ss->pcs[i].flags |= MTK_SGMII_FLAG_PN_SWAP;
+ flags |= MTK_SGMII_FLAG_PN_SWAP;
of_node_put(np);
- if (IS_ERR(ss->pcs[i].regmap))
- return PTR_ERR(ss->pcs[i].regmap);
- ss->pcs[i].pcs.ops = &mtk_pcs_ops;
- ss->pcs[i].pcs.poll = true;
- ss->pcs[i].interface = PHY_INTERFACE_MODE_NA;
+ if (IS_ERR(regmap))
+ return PTR_ERR(regmap);
+
+ ss->pcs[i] = mtk_pcs_lynxi_create(ss->dev, regmap, ana_rgc3,
+ flags);
}
return 0;
@@ -210,8 +46,16 @@ int mtk_sgmii_init(struct mtk_sgmii *ss, struct device_node *r, u32 ana_rgc3)
struct phylink_pcs *mtk_sgmii_select_pcs(struct mtk_sgmii *ss, int id)
{
- if (!ss->pcs[id].regmap)
- return NULL;
+ return ss->pcs[id];
+}
+
+void mtk_sgmii_destroy(struct mtk_sgmii *ss)
+{
+ int i;
+
+ if (!ss)
+ return;
- return &ss->pcs[id].pcs;
+ for (i = 0; i < MTK_MAX_DEVS; i++)
+ mtk_pcs_lynxi_destroy(ss->pcs[i]);
}
@@ -146,6 +146,10 @@ static int mtk_pcs_lynxi_config(struct phylink_pcs *pcs, unsigned int mode,
bmcr = 0;
if (mpcs->interface != interface) {
+ link_timer = phylink_get_link_timer_ns(interface);
+ if (link_timer < 0)
+ return link_timer;
+
/* PHYA power down */
regmap_update_bits(mpcs->regmap, SGMSYS_QPHY_PWR_STATE_CTRL,
SGMII_PHYA_PWD, SGMII_PHYA_PWD);
@@ -168,11 +172,7 @@ static int mtk_pcs_lynxi_config(struct phylink_pcs *pcs, unsigned int mode,
regmap_update_bits(mpcs->regmap, mpcs->ana_rgc3,
RG_PHY_SPEED_MASK, rgc3);
- /* Setup the link timer and QPHY power up inside SGMIISYS */
- link_timer = phylink_get_link_timer_ns(interface);
- if (link_timer < 0)
- return link_timer;
-
+ /* Setup the link timer */
regmap_write(mpcs->regmap, SGMSYS_PCS_LINK_TIMER, link_timer / 2 / 8);
mpcs->interface = interface;