@@ -4976,15 +4976,13 @@ static void mvpp2_gmac_config(struct mvpp2_port *port, unsigned int mode,
old_ctrl2 = ctrl2 = readl(port->base + MVPP2_GMAC_CTRL_2_REG);
old_ctrl4 = ctrl4 = readl(port->base + MVPP22_GMAC_CTRL_4_REG);
- an &= ~(MVPP2_GMAC_CONFIG_MII_SPEED | MVPP2_GMAC_CONFIG_GMII_SPEED |
- MVPP2_GMAC_AN_SPEED_EN | MVPP2_GMAC_FC_ADV_EN |
+ an &= ~(MVPP2_GMAC_AN_SPEED_EN | MVPP2_GMAC_FC_ADV_EN |
MVPP2_GMAC_FC_ADV_ASM_EN | MVPP2_GMAC_FLOW_CTRL_AUTONEG |
- MVPP2_GMAC_CONFIG_FULL_DUPLEX | MVPP2_GMAC_AN_DUPLEX_EN |
- MVPP2_GMAC_IN_BAND_AUTONEG | MVPP2_GMAC_IN_BAND_AUTONEG_BYPASS);
+ MVPP2_GMAC_AN_DUPLEX_EN | MVPP2_GMAC_IN_BAND_AUTONEG |
+ MVPP2_GMAC_IN_BAND_AUTONEG_BYPASS);
ctrl0 &= ~MVPP2_GMAC_PORT_TYPE_MASK;
ctrl2 &= ~(MVPP2_GMAC_INBAND_AN_MASK | MVPP2_GMAC_PORT_RESET_MASK |
MVPP2_GMAC_PCS_ENABLE_MASK);
- ctrl4 &= ~(MVPP22_CTRL4_RX_FC_EN | MVPP22_CTRL4_TX_FC_EN);
/* Configure port type */
if (phy_interface_mode_is_8023z(state->interface)) {
@@ -5014,31 +5012,20 @@ static void mvpp2_gmac_config(struct mvpp2_port *port, unsigned int mode,
/* Configure negotiation style */
if (!phylink_autoneg_inband(mode)) {
- /* Phy or fixed speed - no in-band AN */
- if (state->duplex)
- an |= MVPP2_GMAC_CONFIG_FULL_DUPLEX;
-
- if (state->speed == SPEED_1000 || state->speed == SPEED_2500)
- an |= MVPP2_GMAC_CONFIG_GMII_SPEED;
- else if (state->speed == SPEED_100)
- an |= MVPP2_GMAC_CONFIG_MII_SPEED;
-
- if (state->pause & MLO_PAUSE_TX)
- ctrl4 |= MVPP22_CTRL4_TX_FC_EN;
- if (state->pause & MLO_PAUSE_RX)
- ctrl4 |= MVPP22_CTRL4_RX_FC_EN;
+ /* Phy or fixed speed - no in-band AN, nothing to do, leave the
+ * configured speed, duplex and flow control as-is.
+ */
} else if (state->interface == PHY_INTERFACE_MODE_SGMII) {
/* SGMII in-band mode receives the speed and duplex from
* the PHY. Flow control information is not received. */
- an &= ~(MVPP2_GMAC_FORCE_LINK_DOWN | MVPP2_GMAC_FORCE_LINK_PASS);
+ an &= ~(MVPP2_GMAC_FORCE_LINK_DOWN |
+ MVPP2_GMAC_FORCE_LINK_PASS |
+ MVPP2_GMAC_CONFIG_MII_SPEED |
+ MVPP2_GMAC_CONFIG_GMII_SPEED |
+ MVPP2_GMAC_CONFIG_FULL_DUPLEX);
an |= MVPP2_GMAC_IN_BAND_AUTONEG |
MVPP2_GMAC_AN_SPEED_EN |
MVPP2_GMAC_AN_DUPLEX_EN;
-
- if (state->pause & MLO_PAUSE_TX)
- ctrl4 |= MVPP22_CTRL4_TX_FC_EN;
- if (state->pause & MLO_PAUSE_RX)
- ctrl4 |= MVPP22_CTRL4_RX_FC_EN;
} else if (phy_interface_mode_is_8023z(state->interface)) {
/* 1000BaseX and 2500BaseX ports cannot negotiate speed nor can
* they negotiate duplex: they are always operating with a fixed
@@ -5046,19 +5033,17 @@ static void mvpp2_gmac_config(struct mvpp2_port *port, unsigned int mode,
* speed and full duplex here.
*/
ctrl0 |= MVPP2_GMAC_PORT_TYPE_MASK;
- an &= ~(MVPP2_GMAC_FORCE_LINK_DOWN | MVPP2_GMAC_FORCE_LINK_PASS);
+ an &= ~(MVPP2_GMAC_FORCE_LINK_DOWN |
+ MVPP2_GMAC_FORCE_LINK_PASS |
+ MVPP2_GMAC_CONFIG_MII_SPEED |
+ MVPP2_GMAC_CONFIG_GMII_SPEED |
+ MVPP2_GMAC_CONFIG_FULL_DUPLEX);
an |= MVPP2_GMAC_IN_BAND_AUTONEG |
MVPP2_GMAC_CONFIG_GMII_SPEED |
MVPP2_GMAC_CONFIG_FULL_DUPLEX;
- if (state->pause & MLO_PAUSE_AN && state->an_enabled) {
+ if (state->pause & MLO_PAUSE_AN && state->an_enabled)
an |= MVPP2_GMAC_FLOW_CTRL_AUTONEG;
- } else {
- if (state->pause & MLO_PAUSE_TX)
- ctrl4 |= MVPP22_CTRL4_TX_FC_EN;
- if (state->pause & MLO_PAUSE_RX)
- ctrl4 |= MVPP22_CTRL4_RX_FC_EN;
- }
}
/* Some fields of the auto-negotiation register require the port to be down when
@@ -5155,18 +5140,44 @@ static void mvpp2_mac_link_up(struct phylink_config *config,
struct mvpp2_port *port = netdev_priv(dev);
u32 val;
- if (!phylink_autoneg_inband(mode)) {
- if (mvpp2_is_xlg(interface)) {
+ if (mvpp2_is_xlg(interface)) {
+ if (!phylink_autoneg_inband(mode)) {
val = readl(port->base + MVPP22_XLG_CTRL0_REG);
val &= ~MVPP22_XLG_CTRL0_FORCE_LINK_DOWN;
val |= MVPP22_XLG_CTRL0_FORCE_LINK_PASS;
writel(val, port->base + MVPP22_XLG_CTRL0_REG);
- } else {
+ }
+ } else {
+ if (!phylink_autoneg_inband(mode)) {
val = readl(port->base + MVPP2_GMAC_AUTONEG_CONFIG);
- val &= ~MVPP2_GMAC_FORCE_LINK_DOWN;
+ val &= ~(MVPP2_GMAC_FORCE_LINK_DOWN |
+ MVPP2_GMAC_CONFIG_MII_SPEED |
+ MVPP2_GMAC_CONFIG_GMII_SPEED |
+ MVPP2_GMAC_CONFIG_FULL_DUPLEX);
val |= MVPP2_GMAC_FORCE_LINK_PASS;
+
+ if (speed == SPEED_1000 || speed == SPEED_2500)
+ val |= MVPP2_GMAC_CONFIG_GMII_SPEED;
+ else if (speed == SPEED_100)
+ val |= MVPP2_GMAC_CONFIG_MII_SPEED;
+
+ if (duplex == DUPLEX_FULL)
+ val |= MVPP2_GMAC_CONFIG_FULL_DUPLEX;
+
writel(val, port->base + MVPP2_GMAC_AUTONEG_CONFIG);
}
+
+ /* We can always update the flow control enable bits;
+ * these will only be effective if flow control AN
+ * (MVPP2_GMAC_FLOW_CTRL_AUTONEG) is disabled.
+ */
+ val = readl(port->base + MVPP22_GMAC_CTRL_4_REG);
+ val &= ~(MVPP22_CTRL4_RX_FC_EN | MVPP22_CTRL4_TX_FC_EN);
+ if (tx_pause)
+ val |= MVPP22_CTRL4_TX_FC_EN;
+ if (rx_pause)
+ val |= MVPP22_CTRL4_RX_FC_EN;
+ writel(val, port->base + MVPP22_GMAC_CTRL_4_REG);
}
mvpp2_port_enable(port);
Convert the Marvell mvpp2 ethernet driver to use the finalised link parameters in mac_link_up() rather than the parameters in mac_config(). Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> --- .../net/ethernet/marvell/mvpp2/mvpp2_main.c | 83 +++++++++++-------- 1 file changed, 47 insertions(+), 36 deletions(-)