@@ -3830,13 +3830,9 @@ static void mvneta_mac_config(struct phylink_config *config, unsigned int mode,
new_clk = gmac_clk & ~MVNETA_GMAC_1MS_CLOCK_ENABLE;
new_an = gmac_an & ~(MVNETA_GMAC_INBAND_AN_ENABLE |
MVNETA_GMAC_INBAND_RESTART_AN |
- MVNETA_GMAC_CONFIG_MII_SPEED |
- MVNETA_GMAC_CONFIG_GMII_SPEED |
MVNETA_GMAC_AN_SPEED_EN |
MVNETA_GMAC_ADVERT_SYM_FLOW_CTRL |
- MVNETA_GMAC_CONFIG_FLOW_CTRL |
MVNETA_GMAC_AN_FLOW_CTRL_EN |
- MVNETA_GMAC_CONFIG_FULL_DUPLEX |
MVNETA_GMAC_AN_DUPLEX_EN);
/* Even though it might look weird, when we're configured in
@@ -3851,24 +3847,20 @@ static void mvneta_mac_config(struct phylink_config *config, unsigned int mode,
if (phylink_test(state->advertising, Pause))
new_an |= MVNETA_GMAC_ADVERT_SYM_FLOW_CTRL;
- if (state->pause & MLO_PAUSE_TXRX_MASK)
- new_an |= MVNETA_GMAC_CONFIG_FLOW_CTRL;
if (!phylink_autoneg_inband(mode)) {
- /* Phy or fixed speed */
- if (state->duplex)
- new_an |= MVNETA_GMAC_CONFIG_FULL_DUPLEX;
-
- if (state->speed == SPEED_1000 || state->speed == SPEED_2500)
- new_an |= MVNETA_GMAC_CONFIG_GMII_SPEED;
- else if (state->speed == SPEED_100)
- new_an |= MVNETA_GMAC_CONFIG_MII_SPEED;
+ /* Phy or fixed speed - nothing to do, leave the
+ * configured speed, duplex and flow control as-is.
+ */
} else if (state->interface == PHY_INTERFACE_MODE_SGMII) {
/* SGMII mode receives the state from the PHY */
new_ctrl2 |= MVNETA_GMAC2_INBAND_AN_ENABLE;
new_clk |= MVNETA_GMAC_1MS_CLOCK_ENABLE;
new_an = (new_an & ~(MVNETA_GMAC_FORCE_LINK_DOWN |
- MVNETA_GMAC_FORCE_LINK_PASS)) |
+ MVNETA_GMAC_FORCE_LINK_PASS |
+ MVNETA_GMAC_CONFIG_MII_SPEED |
+ MVNETA_GMAC_CONFIG_GMII_SPEED |
+ MVNETA_GMAC_CONFIG_FULL_DUPLEX)) |
MVNETA_GMAC_INBAND_AN_ENABLE |
MVNETA_GMAC_AN_SPEED_EN |
MVNETA_GMAC_AN_DUPLEX_EN;
@@ -3877,7 +3869,8 @@ static void mvneta_mac_config(struct phylink_config *config, unsigned int mode,
new_ctrl0 |= MVNETA_GMAC0_PORT_1000BASE_X;
new_clk |= MVNETA_GMAC_1MS_CLOCK_ENABLE;
new_an = (new_an & ~(MVNETA_GMAC_FORCE_LINK_DOWN |
- MVNETA_GMAC_FORCE_LINK_PASS)) |
+ MVNETA_GMAC_FORCE_LINK_PASS |
+ MVNETA_GMAC_CONFIG_MII_SPEED)) |
MVNETA_GMAC_INBAND_AN_ENABLE |
MVNETA_GMAC_CONFIG_GMII_SPEED |
/* The MAC only supports FD mode */
@@ -3977,8 +3970,36 @@ static void mvneta_mac_link_up(struct phylink_config *config,
if (!phylink_autoneg_inband(mode)) {
val = mvreg_read(pp, MVNETA_GMAC_AUTONEG_CONFIG);
- val &= ~MVNETA_GMAC_FORCE_LINK_DOWN;
+ val &= ~(MVNETA_GMAC_FORCE_LINK_DOWN |
+ MVNETA_GMAC_CONFIG_MII_SPEED |
+ MVNETA_GMAC_CONFIG_GMII_SPEED |
+ MVNETA_GMAC_CONFIG_FLOW_CTRL |
+ MVNETA_GMAC_CONFIG_FULL_DUPLEX);
val |= MVNETA_GMAC_FORCE_LINK_PASS;
+
+ if (speed == SPEED_1000 || speed == SPEED_2500)
+ val |= MVNETA_GMAC_CONFIG_GMII_SPEED;
+ else if (speed == SPEED_100)
+ val |= MVNETA_GMAC_CONFIG_MII_SPEED;
+
+ if (duplex == DUPLEX_FULL)
+ val |= MVNETA_GMAC_CONFIG_FULL_DUPLEX;
+
+ if (tx_pause || rx_pause)
+ val |= MVNETA_GMAC_CONFIG_FLOW_CTRL;
+
+ mvreg_write(pp, MVNETA_GMAC_AUTONEG_CONFIG, val);
+ } else {
+ /* When inband doesn't cover flow control or flow control is
+ * disabled, we need to manually configure it. This bit will
+ * only have effect if MVNETA_GMAC_AN_FLOW_CTRL_EN is unset.
+ */
+ val = mvreg_read(pp, MVNETA_GMAC_AUTONEG_CONFIG);
+ val &= ~MVNETA_GMAC_CONFIG_FLOW_CTRL;
+
+ if (tx_pause || rx_pause)
+ val |= MVNETA_GMAC_CONFIG_FLOW_CTRL;
+
mvreg_write(pp, MVNETA_GMAC_AUTONEG_CONFIG, val);
}
Convert the Marvell mvneta ethernet driver to use the finalised link parameters in mac_link_up() rather than the parameters in mac_config(). Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> --- drivers/net/ethernet/marvell/mvneta.c | 55 ++++++++++++++++++--------- 1 file changed, 38 insertions(+), 17 deletions(-)