@@ -2699,9 +2699,6 @@ mt7531_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
case PHY_INTERFACE_MODE_NA:
case PHY_INTERFACE_MODE_1000BASEX:
case PHY_INTERFACE_MODE_2500BASEX:
- if (phylink_autoneg_inband(mode))
- return -EINVAL;
-
return mt7531_sgmii_setup_mode_force(priv, port, interface);
default:
return -EINVAL;
@@ -2777,13 +2774,6 @@ mt753x_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
return;
}
- if (phylink_autoneg_inband(mode) &&
- state->interface != PHY_INTERFACE_MODE_SGMII) {
- dev_err(ds->dev, "%s: in-band negotiation unsupported\n",
- __func__);
- return;
- }
-
mcr_cur = mt7530_read(priv, MT7530_PMCR_P(port));
mcr_new = mcr_cur;
mcr_new &= ~PMCR_LINK_SETTINGS_MASK;
@@ -2922,6 +2912,9 @@ static void mt753x_phylink_get_caps(struct dsa_switch *ds, int port,
config->mac_capabilities = MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_10 | MAC_100 | MAC_1000FD;
+ if ((priv->id == ID_MT7531) && mt753x_is_mac_port(port))
+ config->mac_capabilities |= MAC_2500FD;
+
/* This driver does not make use of the speed, duplex, pause or the
* advertisement in its mac_config, so it is safe to mark this driver
* as non-legacy.
@@ -2987,6 +2980,7 @@ mt7531_sgmii_pcs_get_state_an(struct mt7530_priv *priv, int port,
status = mt7530_read(priv, MT7531_PCS_CONTROL_1(port));
state->link = !!(status & MT7531_SGMII_LINK_STATUS);
+ state->an_complete = !!(val & MT7531_SGMII_AN_COMPLETE);
if (state->interface == PHY_INTERFACE_MODE_SGMII &&
(status & MT7531_SGMII_AN_ENABLE)) {
val = mt7530_read(priv, MT7531_PCS_SPEED_ABILITY(port));
@@ -3017,16 +3011,44 @@ mt7531_sgmii_pcs_get_state_an(struct mt7530_priv *priv, int port,
return 0;
}
+static void
+mt7531_sgmii_pcs_get_state_inband(struct mt7530_priv *priv, int port,
+ struct phylink_link_state *state)
+{
+ unsigned int val;
+
+ val = mt7530_read(priv, MT7531_PCS_CONTROL_1(port));
+ state->link = !!(val & MT7531_SGMII_LINK_STATUS);
+ if (!state->link)
+ return;
+
+ state->an_complete = state->link;
+
+ if (state->interface == PHY_INTERFACE_MODE_2500BASEX)
+ state->speed = SPEED_2500;
+ else
+ state->speed = SPEED_1000;
+
+ state->duplex = DUPLEX_FULL;
+ state->pause = MLO_PAUSE_NONE;
+}
+
static void mt7531_pcs_get_state(struct phylink_pcs *pcs,
struct phylink_link_state *state)
{
struct mt7530_priv *priv = pcs_to_mt753x_pcs(pcs)->priv;
int port = pcs_to_mt753x_pcs(pcs)->port;
- if (state->interface == PHY_INTERFACE_MODE_SGMII)
+ if (state->interface == PHY_INTERFACE_MODE_SGMII) {
mt7531_sgmii_pcs_get_state_an(priv, port, state);
- else
- state->link = false;
+ return;
+ } else if ((state->interface == PHY_INTERFACE_MODE_1000BASEX) ||
+ (state->interface == PHY_INTERFACE_MODE_2500BASEX)) {
+ mt7531_sgmii_pcs_get_state_inband(priv, port, state);
+ return;
+ }
+
+ state->link = false;
}
static int mt753x_pcs_config(struct phylink_pcs *pcs, unsigned int mode,
@@ -3067,6 +3089,8 @@ mt753x_setup(struct dsa_switch *ds)
priv->pcs[i].pcs.ops = priv->info->pcs_ops;
priv->pcs[i].priv = priv;
priv->pcs[i].port = i;
+ if (mt753x_is_mac_port(i))
+ priv->pcs[i].pcs.poll = 1;
}
ret = priv->info->sw_setup(ds);
@@ -373,6 +373,7 @@ enum mt7530_vlan_port_acc_frm {
#define MT7531_SGMII_LINK_STATUS BIT(18)
#define MT7531_SGMII_AN_ENABLE BIT(12)
#define MT7531_SGMII_AN_RESTART BIT(9)
+#define MT7531_SGMII_AN_COMPLETE BIT(21)
/* Register for SGMII PCS_SPPED_ABILITY */
#define MT7531_PCS_SPEED_ABILITY(p) MT7531_SGMII_REG(p, 0x08)
Read link status from SGMII PCS for in-band managed 2500Base-X and 1000Base-X connection on a MAC port of the MT7531. This is needed to get the SFP cage working which is connected to SGMII interface of port 5 of the MT7531 switch IC on the Bananapi BPi-R3 board. While at it also handle an_complete for both the autoneg and the non-autoneg codepath. Signed-off-by: Daniel Golle <daniel@makrotopia.org> --- v2: Use MLO_PAUSE_NONE and read an_complete from SGMII status register. v3: Remove unused variable, read an_complete register only in autoneg codepath, set an_complete to link status bit in case of fixed speed link. drivers/net/dsa/mt7530.c | 50 +++++++++++++++++++++++++++++----------- drivers/net/dsa/mt7530.h | 1 + 2 files changed, 38 insertions(+), 13 deletions(-)