@@ -22,7 +22,6 @@ platform-$(CONFIG_MIPS_MALTA) += mti-malta/
platform-$(CONFIG_NLM_COMMON) += netlogic/
platform-$(CONFIG_PIC32MZDA) += pic32/
platform-$(CONFIG_MACH_PISTACHIO) += pistachio/
-platform-$(CONFIG_SOC_PNX833X) += pnx833x/
platform-$(CONFIG_RALINK) += ralink/
platform-$(CONFIG_MIKROTIK_RB532) += rb532/
platform-$(CONFIG_SGI_IP22) += sgi-ip22/
@@ -589,19 +589,6 @@ config MACH_VR41XX
select SYS_SUPPORTS_MIPS16
select GPIOLIB
-config NXP_STB220
- bool "NXP STB220 board"
- select SOC_PNX833X
- help
- Support for NXP Semiconductors STB220 Development Board.
-
-config NXP_STB225
- bool "NXP 225 board"
- select SOC_PNX833X
- select SOC_PNX8335
- help
- Support for NXP Semiconductors STB225 Development Board.
-
config RALINK
bool "Ralink based machines"
select CEVT_R4K
@@ -1266,23 +1253,6 @@ config PCI_XTALK_BRIDGE
config NO_EXCEPT_FILL
bool
-config SOC_PNX833X
- bool
- select CEVT_R4K
- select CSRC_R4K
- select IRQ_MIPS_CPU
- select DMA_NONCOHERENT
- select SYS_HAS_CPU_MIPS32_R2
- select SYS_SUPPORTS_32BIT_KERNEL
- select SYS_SUPPORTS_LITTLE_ENDIAN
- select SYS_SUPPORTS_BIG_ENDIAN
- select SYS_SUPPORTS_MIPS16
- select CPU_MIPSR2_IRQ_VI
-
-config SOC_PNX8335
- bool
- select SOC_PNX833X
-
config MIPS_SPRAM
bool
deleted file mode 100644
@@ -1,77 +0,0 @@
-# CONFIG_LOCALVERSION_AUTO is not set
-# CONFIG_SWAP is not set
-CONFIG_SYSVIPC=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
-CONFIG_PREEMPT_VOLUNTARY=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_EXPERT=y
-CONFIG_SLAB=y
-CONFIG_NXP_STB225=y
-CONFIG_CPU_LITTLE_ENDIAN=y
-CONFIG_HZ_128=y
-# CONFIG_SECCOMP is not set
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_MULTICAST=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-CONFIG_INET_AH=y
-# CONFIG_IPV6 is not set
-CONFIG_MTD=y
-CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_BLOCK=y
-CONFIG_MTD_CFI=y
-CONFIG_MTD_CFI_ADV_OPTIONS=y
-CONFIG_MTD_CFI_LE_BYTE_SWAP=y
-CONFIG_MTD_CFI_GEOMETRY=y
-CONFIG_MTD_CFI_AMDSTD=y
-CONFIG_MTD_PHYSMAP=y
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_BLK_DEV_SD=y
-# CONFIG_SCSI_LOWLEVEL is not set
-CONFIG_ATA=y
-CONFIG_NETDEVICES=y
-CONFIG_INPUT_EVDEV=m
-CONFIG_INPUT_EVBUG=m
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-# CONFIG_VT_CONSOLE is not set
-# CONFIG_LEGACY_PTYS is not set
-CONFIG_SERIAL_PNX8XXX=y
-CONFIG_SERIAL_PNX8XXX_CONSOLE=y
-CONFIG_HW_RANDOM=y
-CONFIG_I2C=y
-CONFIG_I2C_CHARDEV=y
-# CONFIG_HWMON is not set
-CONFIG_FB=y
-# CONFIG_VGA_CONSOLE is not set
-CONFIG_SOUND=m
-CONFIG_SND=m
-CONFIG_SND_VERBOSE_PRINTK=y
-CONFIG_SND_DEBUG=y
-CONFIG_SND_SEQUENCER=m
-CONFIG_EXT2_FS=m
-# CONFIG_DNOTIFY is not set
-CONFIG_MSDOS_FS=m
-CONFIG_VFAT_FS=m
-CONFIG_TMPFS=y
-CONFIG_JFFS2_FS=y
-CONFIG_CRAMFS=y
-CONFIG_NFS_FS=y
-CONFIG_ROOT_NFS=y
-CONFIG_NFSD=m
-CONFIG_NFSD_V3=y
-CONFIG_NLS=y
-CONFIG_NLS_CODEPAGE_437=m
-CONFIG_NLS_CODEPAGE_850=m
-CONFIG_NLS_CODEPAGE_932=m
-CONFIG_NLS_ASCII=m
-CONFIG_NLS_ISO8859_1=m
-CONFIG_NLS_ISO8859_15=m
-CONFIG_NLS_UTF8=m
deleted file mode 100644
@@ -1,159 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * gpio.h: GPIO Support for PNX833X.
- *
- * Copyright 2008 NXP Semiconductors
- * Chris Steel <chris.steel@nxp.com>
- * Daniel Laird <daniel.j.laird@nxp.com>
- */
-#ifndef __ASM_MIPS_MACH_PNX833X_GPIO_H
-#define __ASM_MIPS_MACH_PNX833X_GPIO_H
-
-/* BIG FAT WARNING: races danger!
- No protections exist here. Current users are only early init code,
- when locking is not needed because no concurrency yet exists there,
- and GPIO IRQ dispatcher, which does locking.
- However, if many uses will ever happen, proper locking will be needed
- - including locking between different uses
-*/
-
-#include <asm/mach-pnx833x/pnx833x.h>
-
-#define SET_REG_BIT(reg, bit) do { (reg |= (1 << (bit))); } while (0)
-#define CLEAR_REG_BIT(reg, bit) do { (reg &= ~(1 << (bit))); } while (0)
-
-/* Initialize GPIO to a known state */
-static inline void pnx833x_gpio_init(void)
-{
- PNX833X_PIO_DIR = 0;
- PNX833X_PIO_DIR2 = 0;
- PNX833X_PIO_SEL = 0;
- PNX833X_PIO_SEL2 = 0;
- PNX833X_PIO_INT_EDGE = 0;
- PNX833X_PIO_INT_HI = 0;
- PNX833X_PIO_INT_LO = 0;
-
- /* clear any GPIO interrupt requests */
- PNX833X_PIO_INT_CLEAR = 0xffff;
- PNX833X_PIO_INT_CLEAR = 0;
- PNX833X_PIO_INT_ENABLE = 0;
-}
-
-/* Select GPIO direction for a pin */
-static inline void pnx833x_gpio_select_input(unsigned int pin)
-{
- if (pin < 32)
- CLEAR_REG_BIT(PNX833X_PIO_DIR, pin);
- else
- CLEAR_REG_BIT(PNX833X_PIO_DIR2, pin & 31);
-}
-static inline void pnx833x_gpio_select_output(unsigned int pin)
-{
- if (pin < 32)
- SET_REG_BIT(PNX833X_PIO_DIR, pin);
- else
- SET_REG_BIT(PNX833X_PIO_DIR2, pin & 31);
-}
-
-/* Select GPIO or alternate function for a pin */
-static inline void pnx833x_gpio_select_function_io(unsigned int pin)
-{
- if (pin < 32)
- CLEAR_REG_BIT(PNX833X_PIO_SEL, pin);
- else
- CLEAR_REG_BIT(PNX833X_PIO_SEL2, pin & 31);
-}
-static inline void pnx833x_gpio_select_function_alt(unsigned int pin)
-{
- if (pin < 32)
- SET_REG_BIT(PNX833X_PIO_SEL, pin);
- else
- SET_REG_BIT(PNX833X_PIO_SEL2, pin & 31);
-}
-
-/* Read GPIO pin */
-static inline int pnx833x_gpio_read(unsigned int pin)
-{
- if (pin < 32)
- return (PNX833X_PIO_IN >> pin) & 1;
- else
- return (PNX833X_PIO_IN2 >> (pin & 31)) & 1;
-}
-
-/* Write GPIO pin */
-static inline void pnx833x_gpio_write(unsigned int val, unsigned int pin)
-{
- if (pin < 32) {
- if (val)
- SET_REG_BIT(PNX833X_PIO_OUT, pin);
- else
- CLEAR_REG_BIT(PNX833X_PIO_OUT, pin);
- } else {
- if (val)
- SET_REG_BIT(PNX833X_PIO_OUT2, pin & 31);
- else
- CLEAR_REG_BIT(PNX833X_PIO_OUT2, pin & 31);
- }
-}
-
-/* Configure GPIO interrupt */
-#define GPIO_INT_NONE 0
-#define GPIO_INT_LEVEL_LOW 1
-#define GPIO_INT_LEVEL_HIGH 2
-#define GPIO_INT_EDGE_RISING 3
-#define GPIO_INT_EDGE_FALLING 4
-#define GPIO_INT_EDGE_BOTH 5
-static inline void pnx833x_gpio_setup_irq(int when, unsigned int pin)
-{
- switch (when) {
- case GPIO_INT_LEVEL_LOW:
- CLEAR_REG_BIT(PNX833X_PIO_INT_EDGE, pin);
- CLEAR_REG_BIT(PNX833X_PIO_INT_HI, pin);
- SET_REG_BIT(PNX833X_PIO_INT_LO, pin);
- break;
- case GPIO_INT_LEVEL_HIGH:
- CLEAR_REG_BIT(PNX833X_PIO_INT_EDGE, pin);
- SET_REG_BIT(PNX833X_PIO_INT_HI, pin);
- CLEAR_REG_BIT(PNX833X_PIO_INT_LO, pin);
- break;
- case GPIO_INT_EDGE_RISING:
- SET_REG_BIT(PNX833X_PIO_INT_EDGE, pin);
- SET_REG_BIT(PNX833X_PIO_INT_HI, pin);
- CLEAR_REG_BIT(PNX833X_PIO_INT_LO, pin);
- break;
- case GPIO_INT_EDGE_FALLING:
- SET_REG_BIT(PNX833X_PIO_INT_EDGE, pin);
- CLEAR_REG_BIT(PNX833X_PIO_INT_HI, pin);
- SET_REG_BIT(PNX833X_PIO_INT_LO, pin);
- break;
- case GPIO_INT_EDGE_BOTH:
- SET_REG_BIT(PNX833X_PIO_INT_EDGE, pin);
- SET_REG_BIT(PNX833X_PIO_INT_HI, pin);
- SET_REG_BIT(PNX833X_PIO_INT_LO, pin);
- break;
- default:
- CLEAR_REG_BIT(PNX833X_PIO_INT_EDGE, pin);
- CLEAR_REG_BIT(PNX833X_PIO_INT_HI, pin);
- CLEAR_REG_BIT(PNX833X_PIO_INT_LO, pin);
- break;
- }
-}
-
-/* Enable/disable GPIO interrupt */
-static inline void pnx833x_gpio_enable_irq(unsigned int pin)
-{
- SET_REG_BIT(PNX833X_PIO_INT_ENABLE, pin);
-}
-static inline void pnx833x_gpio_disable_irq(unsigned int pin)
-{
- CLEAR_REG_BIT(PNX833X_PIO_INT_ENABLE, pin);
-}
-
-/* Clear GPIO interrupt request */
-static inline void pnx833x_gpio_clear_irq(unsigned int pin)
-{
- SET_REG_BIT(PNX833X_PIO_INT_CLEAR, pin);
- CLEAR_REG_BIT(PNX833X_PIO_INT_CLEAR, pin);
-}
-
-#endif
deleted file mode 100644
@@ -1,112 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-
-/*
- * irq.h: IRQ mappings for PNX833X.
- *
- * Copyright 2008 NXP Semiconductors
- * Chris Steel <chris.steel@nxp.com>
- * Daniel Laird <daniel.j.laird@nxp.com>
- */
-
-#ifndef __ASM_MIPS_MACH_PNX833X_IRQ_MAPPING_H
-#define __ASM_MIPS_MACH_PNX833X_IRQ_MAPPING_H
-/*
- * The "IRQ numbers" are completely virtual.
- *
- * In PNX8330/1, we have 48 interrupt lines, numbered from 1 to 48.
- * Let's use numbers 1..48 for PIC interrupts, number 0 for timer interrupt,
- * numbers 49..64 for (virtual) GPIO interrupts.
- *
- * In PNX8335, we have 57 interrupt lines, numbered from 1 to 57,
- * connected to PIC, which uses core hardware interrupt 2, and also
- * a timer interrupt through hardware interrupt 5.
- * Let's use numbers 1..64 for PIC interrupts, number 0 for timer interrupt,
- * numbers 65..80 for (virtual) GPIO interrupts.
- *
- */
-#include <irq.h>
-
-#define PNX833X_TIMER_IRQ (MIPS_CPU_IRQ_BASE + 7)
-
-/* Interrupts supported by PIC */
-#define PNX833X_PIC_I2C0_INT (PNX833X_PIC_IRQ_BASE + 1)
-#define PNX833X_PIC_I2C1_INT (PNX833X_PIC_IRQ_BASE + 2)
-#define PNX833X_PIC_UART0_INT (PNX833X_PIC_IRQ_BASE + 3)
-#define PNX833X_PIC_UART1_INT (PNX833X_PIC_IRQ_BASE + 4)
-#define PNX833X_PIC_TS_IN0_DV_INT (PNX833X_PIC_IRQ_BASE + 5)
-#define PNX833X_PIC_TS_IN0_DMA_INT (PNX833X_PIC_IRQ_BASE + 6)
-#define PNX833X_PIC_GPIO_INT (PNX833X_PIC_IRQ_BASE + 7)
-#define PNX833X_PIC_AUDIO_DEC_INT (PNX833X_PIC_IRQ_BASE + 8)
-#define PNX833X_PIC_VIDEO_DEC_INT (PNX833X_PIC_IRQ_BASE + 9)
-#define PNX833X_PIC_CONFIG_INT (PNX833X_PIC_IRQ_BASE + 10)
-#define PNX833X_PIC_AOI_INT (PNX833X_PIC_IRQ_BASE + 11)
-#define PNX833X_PIC_SYNC_INT (PNX833X_PIC_IRQ_BASE + 12)
-#define PNX8330_PIC_SPU_INT (PNX833X_PIC_IRQ_BASE + 13)
-#define PNX8335_PIC_SATA_INT (PNX833X_PIC_IRQ_BASE + 13)
-#define PNX833X_PIC_OSD_INT (PNX833X_PIC_IRQ_BASE + 14)
-#define PNX833X_PIC_DISP1_INT (PNX833X_PIC_IRQ_BASE + 15)
-#define PNX833X_PIC_DEINTERLACER_INT (PNX833X_PIC_IRQ_BASE + 16)
-#define PNX833X_PIC_DISPLAY2_INT (PNX833X_PIC_IRQ_BASE + 17)
-#define PNX833X_PIC_VC_INT (PNX833X_PIC_IRQ_BASE + 18)
-#define PNX833X_PIC_SC_INT (PNX833X_PIC_IRQ_BASE + 19)
-#define PNX833X_PIC_IDE_INT (PNX833X_PIC_IRQ_BASE + 20)
-#define PNX833X_PIC_IDE_DMA_INT (PNX833X_PIC_IRQ_BASE + 21)
-#define PNX833X_PIC_TS_IN1_DV_INT (PNX833X_PIC_IRQ_BASE + 22)
-#define PNX833X_PIC_TS_IN1_DMA_INT (PNX833X_PIC_IRQ_BASE + 23)
-#define PNX833X_PIC_SGDX_DMA_INT (PNX833X_PIC_IRQ_BASE + 24)
-#define PNX833X_PIC_TS_OUT_INT (PNX833X_PIC_IRQ_BASE + 25)
-#define PNX833X_PIC_IR_INT (PNX833X_PIC_IRQ_BASE + 26)
-#define PNX833X_PIC_VMSP1_INT (PNX833X_PIC_IRQ_BASE + 27)
-#define PNX833X_PIC_VMSP2_INT (PNX833X_PIC_IRQ_BASE + 28)
-#define PNX833X_PIC_PIBC_INT (PNX833X_PIC_IRQ_BASE + 29)
-#define PNX833X_PIC_TS_IN0_TRD_INT (PNX833X_PIC_IRQ_BASE + 30)
-#define PNX833X_PIC_SGDX_TPD_INT (PNX833X_PIC_IRQ_BASE + 31)
-#define PNX833X_PIC_USB_INT (PNX833X_PIC_IRQ_BASE + 32)
-#define PNX833X_PIC_TS_IN1_TRD_INT (PNX833X_PIC_IRQ_BASE + 33)
-#define PNX833X_PIC_CLOCK_INT (PNX833X_PIC_IRQ_BASE + 34)
-#define PNX833X_PIC_SGDX_PARSER_INT (PNX833X_PIC_IRQ_BASE + 35)
-#define PNX833X_PIC_VMSP_DMA_INT (PNX833X_PIC_IRQ_BASE + 36)
-
-#if defined(CONFIG_SOC_PNX8335)
-#define PNX8335_PIC_MIU_INT (PNX833X_PIC_IRQ_BASE + 37)
-#define PNX8335_PIC_AVCHIP_IRQ_INT (PNX833X_PIC_IRQ_BASE + 38)
-#define PNX8335_PIC_SYNC_HD_INT (PNX833X_PIC_IRQ_BASE + 39)
-#define PNX8335_PIC_DISP_HD_INT (PNX833X_PIC_IRQ_BASE + 40)
-#define PNX8335_PIC_DISP_SCALER_INT (PNX833X_PIC_IRQ_BASE + 41)
-#define PNX8335_PIC_OSD_HD1_INT (PNX833X_PIC_IRQ_BASE + 42)
-#define PNX8335_PIC_DTL_WRITER_Y_INT (PNX833X_PIC_IRQ_BASE + 43)
-#define PNX8335_PIC_DTL_WRITER_C_INT (PNX833X_PIC_IRQ_BASE + 44)
-#define PNX8335_PIC_DTL_EMULATOR_Y_IR_INT (PNX833X_PIC_IRQ_BASE + 45)
-#define PNX8335_PIC_DTL_EMULATOR_C_IR_INT (PNX833X_PIC_IRQ_BASE + 46)
-#define PNX8335_PIC_DENC_TTX_INT (PNX833X_PIC_IRQ_BASE + 47)
-#define PNX8335_PIC_MMI_SIF0_INT (PNX833X_PIC_IRQ_BASE + 48)
-#define PNX8335_PIC_MMI_SIF1_INT (PNX833X_PIC_IRQ_BASE + 49)
-#define PNX8335_PIC_MMI_CDMMU_INT (PNX833X_PIC_IRQ_BASE + 50)
-#define PNX8335_PIC_PIBCS_INT (PNX833X_PIC_IRQ_BASE + 51)
-#define PNX8335_PIC_ETHERNET_INT (PNX833X_PIC_IRQ_BASE + 52)
-#define PNX8335_PIC_VMSP1_0_INT (PNX833X_PIC_IRQ_BASE + 53)
-#define PNX8335_PIC_VMSP1_1_INT (PNX833X_PIC_IRQ_BASE + 54)
-#define PNX8335_PIC_VMSP1_DMA_INT (PNX833X_PIC_IRQ_BASE + 55)
-#define PNX8335_PIC_TDGR_DE_INT (PNX833X_PIC_IRQ_BASE + 56)
-#define PNX8335_PIC_IR1_IRQ_INT (PNX833X_PIC_IRQ_BASE + 57)
-#endif
-
-/* GPIO interrupts */
-#define PNX833X_GPIO_0_INT (PNX833X_GPIO_IRQ_BASE + 0)
-#define PNX833X_GPIO_1_INT (PNX833X_GPIO_IRQ_BASE + 1)
-#define PNX833X_GPIO_2_INT (PNX833X_GPIO_IRQ_BASE + 2)
-#define PNX833X_GPIO_3_INT (PNX833X_GPIO_IRQ_BASE + 3)
-#define PNX833X_GPIO_4_INT (PNX833X_GPIO_IRQ_BASE + 4)
-#define PNX833X_GPIO_5_INT (PNX833X_GPIO_IRQ_BASE + 5)
-#define PNX833X_GPIO_6_INT (PNX833X_GPIO_IRQ_BASE + 6)
-#define PNX833X_GPIO_7_INT (PNX833X_GPIO_IRQ_BASE + 7)
-#define PNX833X_GPIO_8_INT (PNX833X_GPIO_IRQ_BASE + 8)
-#define PNX833X_GPIO_9_INT (PNX833X_GPIO_IRQ_BASE + 9)
-#define PNX833X_GPIO_10_INT (PNX833X_GPIO_IRQ_BASE + 10)
-#define PNX833X_GPIO_11_INT (PNX833X_GPIO_IRQ_BASE + 11)
-#define PNX833X_GPIO_12_INT (PNX833X_GPIO_IRQ_BASE + 12)
-#define PNX833X_GPIO_13_INT (PNX833X_GPIO_IRQ_BASE + 13)
-#define PNX833X_GPIO_14_INT (PNX833X_GPIO_IRQ_BASE + 14)
-#define PNX833X_GPIO_15_INT (PNX833X_GPIO_IRQ_BASE + 15)
-
-#endif
deleted file mode 100644
@@ -1,40 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * irq.h: IRQ mappings for PNX833X.
- *
- * Copyright 2008 NXP Semiconductors
- * Chris Steel <chris.steel@nxp.com>
- * Daniel Laird <daniel.j.laird@nxp.com>
- */
-
-#ifndef __ASM_MIPS_MACH_PNX833X_IRQ_H
-#define __ASM_MIPS_MACH_PNX833X_IRQ_H
-/*
- * The "IRQ numbers" are completely virtual.
- *
- * In PNX8330/1, we have 48 interrupt lines, numbered from 1 to 48.
- * Let's use numbers 1..48 for PIC interrupts, number 0 for timer interrupt,
- * numbers 49..64 for (virtual) GPIO interrupts.
- *
- * In PNX8335, we have 57 interrupt lines, numbered from 1 to 57,
- * connected to PIC, which uses core hardware interrupt 2, and also
- * a timer interrupt through hardware interrupt 5.
- * Let's use numbers 1..64 for PIC interrupts, number 0 for timer interrupt,
- * numbers 65..80 for (virtual) GPIO interrupts.
- *
- */
-#if defined(CONFIG_SOC_PNX8335)
- #define PNX833X_PIC_NUM_IRQ 58
-#else
- #define PNX833X_PIC_NUM_IRQ 37
-#endif
-
-#define MIPS_CPU_NUM_IRQ 8
-#define PNX833X_GPIO_NUM_IRQ 16
-
-#define MIPS_CPU_IRQ_BASE 0
-#define PNX833X_PIC_IRQ_BASE (MIPS_CPU_IRQ_BASE + MIPS_CPU_NUM_IRQ)
-#define PNX833X_GPIO_IRQ_BASE (PNX833X_PIC_IRQ_BASE + PNX833X_PIC_NUM_IRQ)
-#define NR_IRQS (MIPS_CPU_NUM_IRQ + PNX833X_PIC_NUM_IRQ + PNX833X_GPIO_NUM_IRQ)
-
-#endif
deleted file mode 100644
@@ -1,189 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * pnx833x.h: Register mappings for PNX833X.
- *
- * Copyright 2008 NXP Semiconductors
- * Chris Steel <chris.steel@nxp.com>
- * Daniel Laird <daniel.j.laird@nxp.com>
- */
-#ifndef __ASM_MIPS_MACH_PNX833X_PNX833X_H
-#define __ASM_MIPS_MACH_PNX833X_PNX833X_H
-
-/* All regs are accessed in KSEG1 */
-#define PNX833X_BASE (0xa0000000ul + 0x17E00000ul)
-
-#define PNX833X_REG(offs) (*((volatile unsigned long *)(PNX833X_BASE + offs)))
-
-/* Registers are named exactly as in PNX833X docs, just with PNX833X_ prefix */
-
-/* Read access to multibit fields */
-#define PNX833X_BIT(val, reg, field) ((val) & PNX833X_##reg##_##field)
-#define PNX833X_REGBIT(reg, field) PNX833X_BIT(PNX833X_##reg, reg, field)
-
-/* Use PNX833X_FIELD to extract a field from val */
-#define PNX_FIELD(cpu, val, reg, field) \
- (((val) & PNX##cpu##_##reg##_##field##_MASK) >> \
- PNX##cpu##_##reg##_##field##_SHIFT)
-#define PNX833X_FIELD(val, reg, field) PNX_FIELD(833X, val, reg, field)
-#define PNX8330_FIELD(val, reg, field) PNX_FIELD(8330, val, reg, field)
-#define PNX8335_FIELD(val, reg, field) PNX_FIELD(8335, val, reg, field)
-
-/* Use PNX833X_REGFIELD to extract a field from a register */
-#define PNX833X_REGFIELD(reg, field) PNX833X_FIELD(PNX833X_##reg, reg, field)
-#define PNX8330_REGFIELD(reg, field) PNX8330_FIELD(PNX8330_##reg, reg, field)
-#define PNX8335_REGFIELD(reg, field) PNX8335_FIELD(PNX8335_##reg, reg, field)
-
-
-#define PNX_WRITEFIELD(cpu, val, reg, field) \
- (PNX##cpu##_##reg = (PNX##cpu##_##reg & ~(PNX##cpu##_##reg##_##field##_MASK)) | \
- ((val) << PNX##cpu##_##reg##_##field##_SHIFT))
-#define PNX833X_WRITEFIELD(val, reg, field) \
- PNX_WRITEFIELD(833X, val, reg, field)
-#define PNX8330_WRITEFIELD(val, reg, field) \
- PNX_WRITEFIELD(8330, val, reg, field)
-#define PNX8335_WRITEFIELD(val, reg, field) \
- PNX_WRITEFIELD(8335, val, reg, field)
-
-
-/* Macros to detect CPU type */
-
-#define PNX833X_CONFIG_MODULE_ID PNX833X_REG(0x7FFC)
-#define PNX833X_CONFIG_MODULE_ID_MAJREV_MASK 0x0000f000
-#define PNX833X_CONFIG_MODULE_ID_MAJREV_SHIFT 12
-#define PNX8330_CONFIG_MODULE_MAJREV 4
-#define PNX8335_CONFIG_MODULE_MAJREV 5
-#define CPU_IS_PNX8330 (PNX833X_REGFIELD(CONFIG_MODULE_ID, MAJREV) == \
- PNX8330_CONFIG_MODULE_MAJREV)
-#define CPU_IS_PNX8335 (PNX833X_REGFIELD(CONFIG_MODULE_ID, MAJREV) == \
- PNX8335_CONFIG_MODULE_MAJREV)
-
-
-
-#define PNX833X_RESET_CONTROL PNX833X_REG(0x8004)
-#define PNX833X_RESET_CONTROL_2 PNX833X_REG(0x8014)
-
-#define PNX833X_PIC_REG(offs) PNX833X_REG(0x01000 + (offs))
-#define PNX833X_PIC_INT_PRIORITY PNX833X_PIC_REG(0x0)
-#define PNX833X_PIC_INT_SRC PNX833X_PIC_REG(0x4)
-#define PNX833X_PIC_INT_SRC_INT_SRC_MASK 0x00000FF8ul /* bits 11:3 */
-#define PNX833X_PIC_INT_SRC_INT_SRC_SHIFT 3
-#define PNX833X_PIC_INT_REG(irq) PNX833X_PIC_REG(0x10 + 4*(irq))
-
-#define PNX833X_CLOCK_CPUCP_CTL PNX833X_REG(0x9228)
-#define PNX833X_CLOCK_CPUCP_CTL_EXIT_RESET 0x00000002ul /* bit 1 */
-#define PNX833X_CLOCK_CPUCP_CTL_DIV_CLOCK_MASK 0x00000018ul /* bits 4:3 */
-#define PNX833X_CLOCK_CPUCP_CTL_DIV_CLOCK_SHIFT 3
-
-#define PNX8335_CLOCK_PLL_CPU_CTL PNX833X_REG(0x9020)
-#define PNX8335_CLOCK_PLL_CPU_CTL_FREQ_MASK 0x1f
-#define PNX8335_CLOCK_PLL_CPU_CTL_FREQ_SHIFT 0
-
-#define PNX833X_CONFIG_MUX PNX833X_REG(0x7004)
-#define PNX833X_CONFIG_MUX_IDE_MUX 0x00000080 /* bit 7 */
-
-#define PNX8330_CONFIG_POLYFUSE_7 PNX833X_REG(0x7040)
-#define PNX8330_CONFIG_POLYFUSE_7_BOOT_MODE_MASK 0x00180000
-#define PNX8330_CONFIG_POLYFUSE_7_BOOT_MODE_SHIFT 19
-
-#define PNX833X_PIO_IN PNX833X_REG(0xF000)
-#define PNX833X_PIO_OUT PNX833X_REG(0xF004)
-#define PNX833X_PIO_DIR PNX833X_REG(0xF008)
-#define PNX833X_PIO_SEL PNX833X_REG(0xF014)
-#define PNX833X_PIO_INT_EDGE PNX833X_REG(0xF020)
-#define PNX833X_PIO_INT_HI PNX833X_REG(0xF024)
-#define PNX833X_PIO_INT_LO PNX833X_REG(0xF028)
-#define PNX833X_PIO_INT_STATUS PNX833X_REG(0xFFE0)
-#define PNX833X_PIO_INT_ENABLE PNX833X_REG(0xFFE4)
-#define PNX833X_PIO_INT_CLEAR PNX833X_REG(0xFFE8)
-#define PNX833X_PIO_IN2 PNX833X_REG(0xF05C)
-#define PNX833X_PIO_OUT2 PNX833X_REG(0xF060)
-#define PNX833X_PIO_DIR2 PNX833X_REG(0xF064)
-#define PNX833X_PIO_SEL2 PNX833X_REG(0xF068)
-
-#define PNX833X_UART0_PORTS_START (PNX833X_BASE + 0xB000)
-#define PNX833X_UART0_PORTS_END (PNX833X_BASE + 0xBFFF)
-#define PNX833X_UART1_PORTS_START (PNX833X_BASE + 0xC000)
-#define PNX833X_UART1_PORTS_END (PNX833X_BASE + 0xCFFF)
-
-#define PNX833X_USB_PORTS_START (PNX833X_BASE + 0x19000)
-#define PNX833X_USB_PORTS_END (PNX833X_BASE + 0x19FFF)
-
-#define PNX833X_CONFIG_USB PNX833X_REG(0x7008)
-
-#define PNX833X_I2C0_PORTS_START (PNX833X_BASE + 0xD000)
-#define PNX833X_I2C0_PORTS_END (PNX833X_BASE + 0xDFFF)
-#define PNX833X_I2C1_PORTS_START (PNX833X_BASE + 0xE000)
-#define PNX833X_I2C1_PORTS_END (PNX833X_BASE + 0xEFFF)
-
-#define PNX833X_IDE_PORTS_START (PNX833X_BASE + 0x1A000)
-#define PNX833X_IDE_PORTS_END (PNX833X_BASE + 0x1AFFF)
-#define PNX833X_IDE_MODULE_ID PNX833X_REG(0x1AFFC)
-
-#define PNX833X_IDE_MODULE_ID_MODULE_ID_MASK 0xFFFF0000
-#define PNX833X_IDE_MODULE_ID_MODULE_ID_SHIFT 16
-#define PNX833X_IDE_MODULE_ID_VALUE 0xA009
-
-
-#define PNX833X_MIU_SEL0 PNX833X_REG(0x2004)
-#define PNX833X_MIU_SEL0_TIMING PNX833X_REG(0x2008)
-#define PNX833X_MIU_SEL1 PNX833X_REG(0x200C)
-#define PNX833X_MIU_SEL1_TIMING PNX833X_REG(0x2010)
-#define PNX833X_MIU_SEL2 PNX833X_REG(0x2014)
-#define PNX833X_MIU_SEL2_TIMING PNX833X_REG(0x2018)
-#define PNX833X_MIU_SEL3 PNX833X_REG(0x201C)
-#define PNX833X_MIU_SEL3_TIMING PNX833X_REG(0x2020)
-
-#define PNX833X_MIU_SEL0_SPI_MODE_ENABLE_MASK (1 << 14)
-#define PNX833X_MIU_SEL0_SPI_MODE_ENABLE_SHIFT 14
-
-#define PNX833X_MIU_SEL0_BURST_MODE_ENABLE_MASK (1 << 7)
-#define PNX833X_MIU_SEL0_BURST_MODE_ENABLE_SHIFT 7
-
-#define PNX833X_MIU_SEL0_BURST_PAGE_LEN_MASK (0xF << 9)
-#define PNX833X_MIU_SEL0_BURST_PAGE_LEN_SHIFT 9
-
-#define PNX833X_MIU_CONFIG_SPI PNX833X_REG(0x2000)
-
-#define PNX833X_MIU_CONFIG_SPI_OPCODE_MASK (0xFF << 3)
-#define PNX833X_MIU_CONFIG_SPI_OPCODE_SHIFT 3
-
-#define PNX833X_MIU_CONFIG_SPI_DATA_ENABLE_MASK (1 << 2)
-#define PNX833X_MIU_CONFIG_SPI_DATA_ENABLE_SHIFT 2
-
-#define PNX833X_MIU_CONFIG_SPI_ADDR_ENABLE_MASK (1 << 1)
-#define PNX833X_MIU_CONFIG_SPI_ADDR_ENABLE_SHIFT 1
-
-#define PNX833X_MIU_CONFIG_SPI_SYNC_MASK (1 << 0)
-#define PNX833X_MIU_CONFIG_SPI_SYNC_SHIFT 0
-
-#define PNX833X_WRITE_CONFIG_SPI(opcode, data_enable, addr_enable, sync) \
- (PNX833X_MIU_CONFIG_SPI = \
- ((opcode) << PNX833X_MIU_CONFIG_SPI_OPCODE_SHIFT) | \
- ((data_enable) << PNX833X_MIU_CONFIG_SPI_DATA_ENABLE_SHIFT) | \
- ((addr_enable) << PNX833X_MIU_CONFIG_SPI_ADDR_ENABLE_SHIFT) | \
- ((sync) << PNX833X_MIU_CONFIG_SPI_SYNC_SHIFT))
-
-#define PNX8335_IP3902_PORTS_START (PNX833X_BASE + 0x2F000)
-#define PNX8335_IP3902_PORTS_END (PNX833X_BASE + 0x2FFFF)
-#define PNX8335_IP3902_MODULE_ID PNX833X_REG(0x2FFFC)
-
-#define PNX8335_IP3902_MODULE_ID_MODULE_ID_MASK 0xFFFF0000
-#define PNX8335_IP3902_MODULE_ID_MODULE_ID_SHIFT 16
-#define PNX8335_IP3902_MODULE_ID_VALUE 0x3902
-
- /* I/O location(gets remapped)*/
-#define PNX8335_NAND_BASE 0x18000000
-/* I/O location with CLE high */
-#define PNX8335_NAND_CLE_MASK 0x00100000
-/* I/O location with ALE high */
-#define PNX8335_NAND_ALE_MASK 0x00010000
-
-#define PNX8335_SATA_PORTS_START (PNX833X_BASE + 0x2E000)
-#define PNX8335_SATA_PORTS_END (PNX833X_BASE + 0x2EFFF)
-#define PNX8335_SATA_MODULE_ID PNX833X_REG(0x2EFFC)
-
-#define PNX8335_SATA_MODULE_ID_MODULE_ID_MASK 0xFFFF0000
-#define PNX8335_SATA_MODULE_ID_MODULE_ID_SHIFT 16
-#define PNX8335_SATA_MODULE_ID_VALUE 0xA099
-
-#endif
@@ -1706,12 +1706,6 @@ do { \
#define read_c0_count() __read_32bit_c0_register($9, 0)
#define write_c0_count(val) __write_32bit_c0_register($9, 0, val)
-#define read_c0_count2() __read_32bit_c0_register($9, 6) /* pnx8550 */
-#define write_c0_count2(val) __write_32bit_c0_register($9, 6, val)
-
-#define read_c0_count3() __read_32bit_c0_register($9, 7) /* pnx8550 */
-#define write_c0_count3(val) __write_32bit_c0_register($9, 7, val)
-
#define read_c0_entryhi() __read_ulong_c0_register($10, 0)
#define write_c0_entryhi(val) __write_ulong_c0_register($10, 0, val)
@@ -1730,12 +1724,6 @@ do { \
#define read_c0_guestctl0ext() __read_32bit_c0_register($11, 4)
#define write_c0_guestctl0ext(val) __write_32bit_c0_register($11, 4, val)
-#define read_c0_compare2() __read_32bit_c0_register($11, 6) /* pnx8550 */
-#define write_c0_compare2(val) __write_32bit_c0_register($11, 6, val)
-
-#define read_c0_compare3() __read_32bit_c0_register($11, 7) /* pnx8550 */
-#define write_c0_compare3(val) __write_32bit_c0_register($11, 7, val)
-
#define read_c0_status() __read_32bit_c0_register($12, 0)
#define write_c0_status(val) __write_32bit_c0_register($12, 0, val)
deleted file mode 100644
@@ -1,4 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0-only
-obj-$(CONFIG_SOC_PNX833X) += common/
-obj-$(CONFIG_NXP_STB220) += stb22x/
-obj-$(CONFIG_NXP_STB225) += stb22x/
deleted file mode 100644
@@ -1,4 +0,0 @@
-# NXP STB225
-cflags-$(CONFIG_SOC_PNX833X) += -I$(srctree)/arch/mips/include/asm/mach-pnx833x
-load-$(CONFIG_NXP_STB220) += 0xffffffff80001000
-load-$(CONFIG_NXP_STB225) += 0xffffffff80001000
deleted file mode 100644
@@ -1,2 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0-only
-obj-y := interrupts.o platform.o prom.o setup.o reset.o
deleted file mode 100644
@@ -1,303 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * interrupts.c: Interrupt mappings for PNX833X.
- *
- * Copyright 2008 NXP Semiconductors
- * Chris Steel <chris.steel@nxp.com>
- * Daniel Laird <daniel.j.laird@nxp.com>
- */
-#include <linux/kernel.h>
-#include <linux/irq.h>
-#include <linux/hardirq.h>
-#include <linux/interrupt.h>
-#include <asm/mipsregs.h>
-#include <asm/irq_cpu.h>
-#include <asm/setup.h>
-#include <irq.h>
-#include <irq-mapping.h>
-#include <gpio.h>
-
-static int mips_cpu_timer_irq;
-
-static const unsigned int irq_prio[PNX833X_PIC_NUM_IRQ] =
-{
- 0, /* unused */
- 4, /* PNX833X_PIC_I2C0_INT 1 */
- 4, /* PNX833X_PIC_I2C1_INT 2 */
- 1, /* PNX833X_PIC_UART0_INT 3 */
- 1, /* PNX833X_PIC_UART1_INT 4 */
- 6, /* PNX833X_PIC_TS_IN0_DV_INT 5 */
- 6, /* PNX833X_PIC_TS_IN0_DMA_INT 6 */
- 7, /* PNX833X_PIC_GPIO_INT 7 */
- 4, /* PNX833X_PIC_AUDIO_DEC_INT 8 */
- 5, /* PNX833X_PIC_VIDEO_DEC_INT 9 */
- 4, /* PNX833X_PIC_CONFIG_INT 10 */
- 4, /* PNX833X_PIC_AOI_INT 11 */
- 9, /* PNX833X_PIC_SYNC_INT 12 */
- 9, /* PNX8335_PIC_SATA_INT 13 */
- 4, /* PNX833X_PIC_OSD_INT 14 */
- 9, /* PNX833X_PIC_DISP1_INT 15 */
- 4, /* PNX833X_PIC_DEINTERLACER_INT 16 */
- 9, /* PNX833X_PIC_DISPLAY2_INT 17 */
- 4, /* PNX833X_PIC_VC_INT 18 */
- 4, /* PNX833X_PIC_SC_INT 19 */
- 9, /* PNX833X_PIC_IDE_INT 20 */
- 9, /* PNX833X_PIC_IDE_DMA_INT 21 */
- 6, /* PNX833X_PIC_TS_IN1_DV_INT 22 */
- 6, /* PNX833X_PIC_TS_IN1_DMA_INT 23 */
- 4, /* PNX833X_PIC_SGDX_DMA_INT 24 */
- 4, /* PNX833X_PIC_TS_OUT_INT 25 */
- 4, /* PNX833X_PIC_IR_INT 26 */
- 3, /* PNX833X_PIC_VMSP1_INT 27 */
- 3, /* PNX833X_PIC_VMSP2_INT 28 */
- 4, /* PNX833X_PIC_PIBC_INT 29 */
- 4, /* PNX833X_PIC_TS_IN0_TRD_INT 30 */
- 4, /* PNX833X_PIC_SGDX_TPD_INT 31 */
- 5, /* PNX833X_PIC_USB_INT 32 */
- 4, /* PNX833X_PIC_TS_IN1_TRD_INT 33 */
- 4, /* PNX833X_PIC_CLOCK_INT 34 */
- 4, /* PNX833X_PIC_SGDX_PARSER_INT 35 */
- 4, /* PNX833X_PIC_VMSP_DMA_INT 36 */
-#if defined(CONFIG_SOC_PNX8335)
- 4, /* PNX8335_PIC_MIU_INT 37 */
- 4, /* PNX8335_PIC_AVCHIP_IRQ_INT 38 */
- 9, /* PNX8335_PIC_SYNC_HD_INT 39 */
- 9, /* PNX8335_PIC_DISP_HD_INT 40 */
- 9, /* PNX8335_PIC_DISP_SCALER_INT 41 */
- 4, /* PNX8335_PIC_OSD_HD1_INT 42 */
- 4, /* PNX8335_PIC_DTL_WRITER_Y_INT 43 */
- 4, /* PNX8335_PIC_DTL_WRITER_C_INT 44 */
- 4, /* PNX8335_PIC_DTL_EMULATOR_Y_IR_INT 45 */
- 4, /* PNX8335_PIC_DTL_EMULATOR_C_IR_INT 46 */
- 4, /* PNX8335_PIC_DENC_TTX_INT 47 */
- 4, /* PNX8335_PIC_MMI_SIF0_INT 48 */
- 4, /* PNX8335_PIC_MMI_SIF1_INT 49 */
- 4, /* PNX8335_PIC_MMI_CDMMU_INT 50 */
- 4, /* PNX8335_PIC_PIBCS_INT 51 */
- 12, /* PNX8335_PIC_ETHERNET_INT 52 */
- 3, /* PNX8335_PIC_VMSP1_0_INT 53 */
- 3, /* PNX8335_PIC_VMSP1_1_INT 54 */
- 4, /* PNX8335_PIC_VMSP1_DMA_INT 55 */
- 4, /* PNX8335_PIC_TDGR_DE_INT 56 */
- 4, /* PNX8335_PIC_IR1_IRQ_INT 57 */
-#endif
-};
-
-static void pnx833x_timer_dispatch(void)
-{
- do_IRQ(mips_cpu_timer_irq);
-}
-
-static void pic_dispatch(void)
-{
- unsigned int irq = PNX833X_REGFIELD(PIC_INT_SRC, INT_SRC);
-
- if ((irq >= 1) && (irq < (PNX833X_PIC_NUM_IRQ))) {
- unsigned long priority = PNX833X_PIC_INT_PRIORITY;
- PNX833X_PIC_INT_PRIORITY = irq_prio[irq];
-
- if (irq == PNX833X_PIC_GPIO_INT) {
- unsigned long mask = PNX833X_PIO_INT_STATUS & PNX833X_PIO_INT_ENABLE;
- int pin;
- while ((pin = ffs(mask & 0xffff))) {
- pin -= 1;
- do_IRQ(PNX833X_GPIO_IRQ_BASE + pin);
- mask &= ~(1 << pin);
- }
- } else {
- do_IRQ(irq + PNX833X_PIC_IRQ_BASE);
- }
-
- PNX833X_PIC_INT_PRIORITY = priority;
- } else {
- printk(KERN_ERR "plat_irq_dispatch: unexpected irq %u\n", irq);
- }
-}
-
-asmlinkage void plat_irq_dispatch(void)
-{
- unsigned int pending = read_c0_status() & read_c0_cause();
-
- if (pending & STATUSF_IP4)
- pic_dispatch();
- else if (pending & STATUSF_IP7)
- do_IRQ(PNX833X_TIMER_IRQ);
- else
- spurious_interrupt();
-}
-
-static inline void pnx833x_hard_enable_pic_irq(unsigned int irq)
-{
- /* Currently we do this by setting IRQ priority to 1.
- If priority support is being implemented, 1 should be repalced
- by a better value. */
- PNX833X_PIC_INT_REG(irq) = irq_prio[irq];
-}
-
-static inline void pnx833x_hard_disable_pic_irq(unsigned int irq)
-{
- /* Disable IRQ by writing setting it's priority to 0 */
- PNX833X_PIC_INT_REG(irq) = 0;
-}
-
-static DEFINE_RAW_SPINLOCK(pnx833x_irq_lock);
-
-static unsigned int pnx833x_startup_pic_irq(unsigned int irq)
-{
- unsigned long flags;
- unsigned int pic_irq = irq - PNX833X_PIC_IRQ_BASE;
-
- raw_spin_lock_irqsave(&pnx833x_irq_lock, flags);
- pnx833x_hard_enable_pic_irq(pic_irq);
- raw_spin_unlock_irqrestore(&pnx833x_irq_lock, flags);
- return 0;
-}
-
-static void pnx833x_enable_pic_irq(struct irq_data *d)
-{
- unsigned long flags;
- unsigned int pic_irq = d->irq - PNX833X_PIC_IRQ_BASE;
-
- raw_spin_lock_irqsave(&pnx833x_irq_lock, flags);
- pnx833x_hard_enable_pic_irq(pic_irq);
- raw_spin_unlock_irqrestore(&pnx833x_irq_lock, flags);
-}
-
-static void pnx833x_disable_pic_irq(struct irq_data *d)
-{
- unsigned long flags;
- unsigned int pic_irq = d->irq - PNX833X_PIC_IRQ_BASE;
-
- raw_spin_lock_irqsave(&pnx833x_irq_lock, flags);
- pnx833x_hard_disable_pic_irq(pic_irq);
- raw_spin_unlock_irqrestore(&pnx833x_irq_lock, flags);
-}
-
-static DEFINE_RAW_SPINLOCK(pnx833x_gpio_pnx833x_irq_lock);
-
-static void pnx833x_enable_gpio_irq(struct irq_data *d)
-{
- int pin = d->irq - PNX833X_GPIO_IRQ_BASE;
- unsigned long flags;
- raw_spin_lock_irqsave(&pnx833x_gpio_pnx833x_irq_lock, flags);
- pnx833x_gpio_enable_irq(pin);
- raw_spin_unlock_irqrestore(&pnx833x_gpio_pnx833x_irq_lock, flags);
-}
-
-static void pnx833x_disable_gpio_irq(struct irq_data *d)
-{
- int pin = d->irq - PNX833X_GPIO_IRQ_BASE;
- unsigned long flags;
- raw_spin_lock_irqsave(&pnx833x_gpio_pnx833x_irq_lock, flags);
- pnx833x_gpio_disable_irq(pin);
- raw_spin_unlock_irqrestore(&pnx833x_gpio_pnx833x_irq_lock, flags);
-}
-
-static int pnx833x_set_type_gpio_irq(struct irq_data *d, unsigned int flow_type)
-{
- int pin = d->irq - PNX833X_GPIO_IRQ_BASE;
- int gpio_mode;
-
- switch (flow_type) {
- case IRQ_TYPE_EDGE_RISING:
- gpio_mode = GPIO_INT_EDGE_RISING;
- break;
- case IRQ_TYPE_EDGE_FALLING:
- gpio_mode = GPIO_INT_EDGE_FALLING;
- break;
- case IRQ_TYPE_EDGE_BOTH:
- gpio_mode = GPIO_INT_EDGE_BOTH;
- break;
- case IRQ_TYPE_LEVEL_HIGH:
- gpio_mode = GPIO_INT_LEVEL_HIGH;
- break;
- case IRQ_TYPE_LEVEL_LOW:
- gpio_mode = GPIO_INT_LEVEL_LOW;
- break;
- default:
- gpio_mode = GPIO_INT_NONE;
- break;
- }
-
- pnx833x_gpio_setup_irq(gpio_mode, pin);
-
- return 0;
-}
-
-static struct irq_chip pnx833x_pic_irq_type = {
- .name = "PNX-PIC",
- .irq_enable = pnx833x_enable_pic_irq,
- .irq_disable = pnx833x_disable_pic_irq,
-};
-
-static struct irq_chip pnx833x_gpio_irq_type = {
- .name = "PNX-GPIO",
- .irq_enable = pnx833x_enable_gpio_irq,
- .irq_disable = pnx833x_disable_gpio_irq,
- .irq_set_type = pnx833x_set_type_gpio_irq,
-};
-
-void __init arch_init_irq(void)
-{
- unsigned int irq;
-
- /* setup standard internal cpu irqs */
- mips_cpu_irq_init();
-
- /* Set IRQ information in irq_desc */
- for (irq = PNX833X_PIC_IRQ_BASE; irq < (PNX833X_PIC_IRQ_BASE + PNX833X_PIC_NUM_IRQ); irq++) {
- pnx833x_hard_disable_pic_irq(irq);
- irq_set_chip_and_handler(irq, &pnx833x_pic_irq_type,
- handle_simple_irq);
- }
-
- for (irq = PNX833X_GPIO_IRQ_BASE; irq < (PNX833X_GPIO_IRQ_BASE + PNX833X_GPIO_NUM_IRQ); irq++)
- irq_set_chip_and_handler(irq, &pnx833x_gpio_irq_type,
- handle_simple_irq);
-
- /* Set PIC priority limiter register to 0 */
- PNX833X_PIC_INT_PRIORITY = 0;
-
- /* Setup GPIO IRQ dispatching */
- pnx833x_startup_pic_irq(PNX833X_PIC_GPIO_INT);
-
- /* Enable PIC IRQs (HWIRQ2) */
- if (cpu_has_vint)
- set_vi_handler(4, pic_dispatch);
-
- write_c0_status(read_c0_status() | IE_IRQ2);
-}
-
-unsigned int get_c0_compare_int(void)
-{
- if (cpu_has_vint)
- set_vi_handler(cp0_compare_irq, pnx833x_timer_dispatch);
-
- mips_cpu_timer_irq = MIPS_CPU_IRQ_BASE + cp0_compare_irq;
- return mips_cpu_timer_irq;
-}
-
-void __init plat_time_init(void)
-{
- /* calculate mips_hpt_frequency based on PNX833X_CLOCK_CPUCP_CTL reg */
-
- extern unsigned long mips_hpt_frequency;
- unsigned long reg = PNX833X_CLOCK_CPUCP_CTL;
-
- if (!(PNX833X_BIT(reg, CLOCK_CPUCP_CTL, EXIT_RESET))) {
- /* Functional clock is disabled so use crystal frequency */
- mips_hpt_frequency = 25;
- } else {
-#if defined(CONFIG_SOC_PNX8335)
- /* Functional clock is enabled, so get clock multiplier */
- mips_hpt_frequency = 90 + (10 * PNX8335_REGFIELD(CLOCK_PLL_CPU_CTL, FREQ));
-#else
- static const unsigned long int freq[4] = {240, 160, 120, 80};
- mips_hpt_frequency = freq[PNX833X_FIELD(reg, CLOCK_CPUCP_CTL, DIV_CLOCK)];
-#endif
- }
-
- printk(KERN_INFO "CPU clock is %ld MHz\n", mips_hpt_frequency);
-
- mips_hpt_frequency *= 500000;
-}
deleted file mode 100644
@@ -1,224 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * platform.c: platform support for PNX833X.
- *
- * Copyright 2008 NXP Semiconductors
- * Chris Steel <chris.steel@nxp.com>
- * Daniel Laird <daniel.j.laird@nxp.com>
- *
- * Based on software written by:
- * Nikita Youshchenko <yoush@debian.org>, based on PNX8550 code.
- */
-#include <linux/device.h>
-#include <linux/dma-mapping.h>
-#include <linux/platform_device.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/resource.h>
-#include <linux/serial.h>
-#include <linux/serial_pnx8xxx.h>
-#include <linux/mtd/platnand.h>
-
-#include <irq.h>
-#include <irq-mapping.h>
-#include <pnx833x.h>
-
-static u64 uart_dmamask = DMA_BIT_MASK(32);
-
-static struct resource pnx833x_uart_resources[] = {
- [0] = {
- .start = PNX833X_UART0_PORTS_START,
- .end = PNX833X_UART0_PORTS_END,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = PNX833X_PIC_UART0_INT,
- .end = PNX833X_PIC_UART0_INT,
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .start = PNX833X_UART1_PORTS_START,
- .end = PNX833X_UART1_PORTS_END,
- .flags = IORESOURCE_MEM,
- },
- [3] = {
- .start = PNX833X_PIC_UART1_INT,
- .end = PNX833X_PIC_UART1_INT,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-struct pnx8xxx_port pnx8xxx_ports[] = {
- [0] = {
- .port = {
- .type = PORT_PNX8XXX,
- .iotype = UPIO_MEM,
- .membase = (void __iomem *)PNX833X_UART0_PORTS_START,
- .mapbase = PNX833X_UART0_PORTS_START,
- .irq = PNX833X_PIC_UART0_INT,
- .uartclk = 3692300,
- .fifosize = 16,
- .flags = UPF_BOOT_AUTOCONF,
- .line = 0,
- },
- },
- [1] = {
- .port = {
- .type = PORT_PNX8XXX,
- .iotype = UPIO_MEM,
- .membase = (void __iomem *)PNX833X_UART1_PORTS_START,
- .mapbase = PNX833X_UART1_PORTS_START,
- .irq = PNX833X_PIC_UART1_INT,
- .uartclk = 3692300,
- .fifosize = 16,
- .flags = UPF_BOOT_AUTOCONF,
- .line = 1,
- },
- },
-};
-
-static struct platform_device pnx833x_uart_device = {
- .name = "pnx8xxx-uart",
- .id = -1,
- .dev = {
- .dma_mask = &uart_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = pnx8xxx_ports,
- },
- .num_resources = ARRAY_SIZE(pnx833x_uart_resources),
- .resource = pnx833x_uart_resources,
-};
-
-static u64 ehci_dmamask = DMA_BIT_MASK(32);
-
-static struct resource pnx833x_usb_ehci_resources[] = {
- [0] = {
- .start = PNX833X_USB_PORTS_START,
- .end = PNX833X_USB_PORTS_END,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = PNX833X_PIC_USB_INT,
- .end = PNX833X_PIC_USB_INT,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device pnx833x_usb_ehci_device = {
- .name = "pnx833x-ehci",
- .id = -1,
- .dev = {
- .dma_mask = &ehci_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .num_resources = ARRAY_SIZE(pnx833x_usb_ehci_resources),
- .resource = pnx833x_usb_ehci_resources,
-};
-
-static u64 ethernet_dmamask = DMA_BIT_MASK(32);
-
-static struct resource pnx833x_ethernet_resources[] = {
- [0] = {
- .start = PNX8335_IP3902_PORTS_START,
- .end = PNX8335_IP3902_PORTS_END,
- .flags = IORESOURCE_MEM,
- },
-#ifdef CONFIG_SOC_PNX8335
- [1] = {
- .start = PNX8335_PIC_ETHERNET_INT,
- .end = PNX8335_PIC_ETHERNET_INT,
- .flags = IORESOURCE_IRQ,
- },
-#endif
-};
-
-static struct platform_device pnx833x_ethernet_device = {
- .name = "ip3902-eth",
- .id = -1,
- .dev = {
- .dma_mask = ðernet_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .num_resources = ARRAY_SIZE(pnx833x_ethernet_resources),
- .resource = pnx833x_ethernet_resources,
-};
-
-static struct resource pnx833x_sata_resources[] = {
- [0] = {
- .start = PNX8335_SATA_PORTS_START,
- .end = PNX8335_SATA_PORTS_END,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = PNX8335_PIC_SATA_INT,
- .end = PNX8335_PIC_SATA_INT,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device pnx833x_sata_device = {
- .name = "pnx833x-sata",
- .id = -1,
- .num_resources = ARRAY_SIZE(pnx833x_sata_resources),
- .resource = pnx833x_sata_resources,
-};
-
-static void
-pnx833x_flash_nand_cmd_ctrl(struct nand_chip *this, int cmd, unsigned int ctrl)
-{
- unsigned long nandaddr = (unsigned long)this->legacy.IO_ADDR_W;
-
- if (cmd == NAND_CMD_NONE)
- return;
-
- if (ctrl & NAND_CLE)
- writeb(cmd, (void __iomem *)(nandaddr + PNX8335_NAND_CLE_MASK));
- else
- writeb(cmd, (void __iomem *)(nandaddr + PNX8335_NAND_ALE_MASK));
-}
-
-static struct platform_nand_data pnx833x_flash_nand_data = {
- .chip = {
- .nr_chips = 1,
- .chip_delay = 25,
- },
- .ctrl = {
- .cmd_ctrl = pnx833x_flash_nand_cmd_ctrl
- }
-};
-
-/*
- * Set start to be the correct address (PNX8335_NAND_BASE with no 0xb!!),
- * 12 bytes more seems to be the standard that allows for NAND access.
- */
-static struct resource pnx833x_flash_nand_resource = {
- .start = PNX8335_NAND_BASE,
- .end = PNX8335_NAND_BASE + 12,
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device pnx833x_flash_nand = {
- .name = "gen_nand",
- .id = -1,
- .num_resources = 1,
- .resource = &pnx833x_flash_nand_resource,
- .dev = {
- .platform_data = &pnx833x_flash_nand_data,
- },
-};
-
-static struct platform_device *pnx833x_platform_devices[] __initdata = {
- &pnx833x_uart_device,
- &pnx833x_usb_ehci_device,
- &pnx833x_ethernet_device,
- &pnx833x_sata_device,
- &pnx833x_flash_nand,
-};
-
-static int __init pnx833x_platform_init(void)
-{
- return platform_add_devices(pnx833x_platform_devices,
- ARRAY_SIZE(pnx833x_platform_devices));
-}
-
-arch_initcall(pnx833x_platform_init);
deleted file mode 100644
@@ -1,51 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * prom.c:
- *
- * Copyright 2008 NXP Semiconductors
- * Chris Steel <chris.steel@nxp.com>
- * Daniel Laird <daniel.j.laird@nxp.com>
- *
- * Based on software written by:
- * Nikita Youshchenko <yoush@debian.org>, based on PNX8550 code.
- */
-#include <linux/init.h>
-#include <asm/bootinfo.h>
-#include <linux/string.h>
-
-void __init prom_init_cmdline(void)
-{
- int argc = fw_arg0;
- char **argv = (char **)fw_arg1;
- char *c = &(arcs_cmdline[0]);
- int i;
-
- for (i = 1; i < argc; i++) {
- strcpy(c, argv[i]);
- c += strlen(argv[i]);
- if (i < argc-1)
- *c++ = ' ';
- }
- *c = 0;
-}
-
-char __init *prom_getenv(char *envname)
-{
- extern char **prom_envp;
- char **env = prom_envp;
- int i;
-
- i = strlen(envname);
-
- while (*env) {
- if (strncmp(envname, *env, i) == 0 && *(*env+i) == '=')
- return *env + i + 1;
- env++;
- }
-
- return 0;
-}
-
-void __init prom_free_prom_memory(void)
-{
-}
deleted file mode 100644
@@ -1,31 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * reset.c: reset support for PNX833X.
- *
- * Copyright 2008 NXP Semiconductors
- * Chris Steel <chris.steel@nxp.com>
- * Daniel Laird <daniel.j.laird@nxp.com>
- *
- * Based on software written by:
- * Nikita Youshchenko <yoush@debian.org>, based on PNX8550 code.
- */
-#include <linux/reboot.h>
-#include <pnx833x.h>
-
-void pnx833x_machine_restart(char *command)
-{
- PNX833X_RESET_CONTROL_2 = 0;
- PNX833X_RESET_CONTROL = 0;
-}
-
-void pnx833x_machine_halt(void)
-{
- while (1)
- __asm__ __volatile__ ("wait");
-
-}
-
-void pnx833x_machine_power_off(void)
-{
- pnx833x_machine_halt();
-}
deleted file mode 100644
@@ -1,48 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * setup.c: Setup PNX833X Soc.
- *
- * Copyright 2008 NXP Semiconductors
- * Chris Steel <chris.steel@nxp.com>
- * Daniel Laird <daniel.j.laird@nxp.com>
- *
- * Based on software written by:
- * Nikita Youshchenko <yoush@debian.org>, based on PNX8550 code.
- */
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/ioport.h>
-#include <linux/io.h>
-#include <linux/pci.h>
-#include <asm/reboot.h>
-#include <pnx833x.h>
-#include <gpio.h>
-
-extern void pnx833x_board_setup(void);
-extern void pnx833x_machine_restart(char *);
-extern void pnx833x_machine_halt(void);
-extern void pnx833x_machine_power_off(void);
-
-int __init plat_mem_setup(void)
-{
- /* set mips clock to 320MHz */
-#if defined(CONFIG_SOC_PNX8335)
- PNX8335_WRITEFIELD(0x17, CLOCK_PLL_CPU_CTL, FREQ);
-#endif
- pnx833x_gpio_init(); /* so it will be ready in board_setup() */
-
- pnx833x_board_setup();
-
- _machine_restart = pnx833x_machine_restart;
- _machine_halt = pnx833x_machine_halt;
- pm_power_off = pnx833x_machine_power_off;
-
- /* IO/MEM resources. */
- set_io_port_base(KSEG1);
- ioport_resource.start = 0;
- ioport_resource.end = ~0;
- iomem_resource.start = 0;
- iomem_resource.end = ~0;
-
- return 0;
-}
deleted file mode 100644
@@ -1,2 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0-only
-obj-y := board.o
deleted file mode 100644
@@ -1,120 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * board.c: STB225 board support.
- *
- * Copyright 2008 NXP Semiconductors
- * Chris Steel <chris.steel@nxp.com>
- * Daniel Laird <daniel.j.laird@nxp.com>
- *
- * Based on software written by:
- * Nikita Youshchenko <yoush@debian.org>, based on PNX8550 code.
- */
-#include <linux/init.h>
-#include <asm/bootinfo.h>
-#include <linux/mm.h>
-#include <pnx833x.h>
-#include <gpio.h>
-
-/* endianess twiddlers */
-#define PNX8335_DEBUG0 0x4400
-#define PNX8335_DEBUG1 0x4404
-#define PNX8335_DEBUG2 0x4408
-#define PNX8335_DEBUG3 0x440c
-#define PNX8335_DEBUG4 0x4410
-#define PNX8335_DEBUG5 0x4414
-#define PNX8335_DEBUG6 0x4418
-#define PNX8335_DEBUG7 0x441c
-
-int prom_argc;
-char **prom_argv, **prom_envp;
-
-extern void prom_init_cmdline(void);
-extern char *prom_getenv(char *envname);
-
-const char *get_system_type(void)
-{
- return "NXP STB22x";
-}
-
-static inline unsigned long env_or_default(char *env, unsigned long dfl)
-{
- char *str = prom_getenv(env);
- return str ? simple_strtol(str, 0, 0) : dfl;
-}
-
-void __init prom_init(void)
-{
- unsigned long memsize;
-
- prom_argc = fw_arg0;
- prom_argv = (char **)fw_arg1;
- prom_envp = (char **)fw_arg2;
-
- prom_init_cmdline();
-
- memsize = env_or_default("memsize", 0x02000000);
- add_memory_region(0, memsize, BOOT_MEM_RAM);
-}
-
-void __init pnx833x_board_setup(void)
-{
- pnx833x_gpio_select_function_alt(4);
- pnx833x_gpio_select_output(4);
- pnx833x_gpio_select_function_alt(5);
- pnx833x_gpio_select_input(5);
- pnx833x_gpio_select_function_alt(6);
- pnx833x_gpio_select_input(6);
- pnx833x_gpio_select_function_alt(7);
- pnx833x_gpio_select_output(7);
-
- pnx833x_gpio_select_function_alt(25);
- pnx833x_gpio_select_function_alt(26);
-
- pnx833x_gpio_select_function_alt(27);
- pnx833x_gpio_select_function_alt(28);
- pnx833x_gpio_select_function_alt(29);
- pnx833x_gpio_select_function_alt(30);
- pnx833x_gpio_select_function_alt(31);
- pnx833x_gpio_select_function_alt(32);
- pnx833x_gpio_select_function_alt(33);
-
-#if IS_ENABLED(CONFIG_MTD_NAND_PLATFORM)
- /* Setup MIU for NAND access on CS0...
- *
- * (it seems that we must also configure CS1 for reliable operation,
- * otherwise the first read ID command will fail if it's read as 4 bytes
- * but pass if it's read as 1 word.)
- */
-
- /* Setup MIU CS0 & CS1 timing */
- PNX833X_MIU_SEL0 = 0;
- PNX833X_MIU_SEL1 = 0;
- PNX833X_MIU_SEL0_TIMING = 0x50003081;
- PNX833X_MIU_SEL1_TIMING = 0x50003081;
-
- /* Setup GPIO 00 for use as MIU CS1 (CS0 is not multiplexed, so does not need this) */
- pnx833x_gpio_select_function_alt(0);
-
- /* Setup GPIO 04 to input NAND read/busy signal */
- pnx833x_gpio_select_function_io(4);
- pnx833x_gpio_select_input(4);
-
- /* Setup GPIO 05 to disable NAND write protect */
- pnx833x_gpio_select_function_io(5);
- pnx833x_gpio_select_output(5);
- pnx833x_gpio_write(1, 5);
-
-#elif IS_ENABLED(CONFIG_MTD_CFI)
-
- /* Set up MIU for 16-bit NOR access on CS0 and CS1... */
-
- /* Setup MIU CS0 & CS1 timing */
- PNX833X_MIU_SEL0 = 1;
- PNX833X_MIU_SEL1 = 1;
- PNX833X_MIU_SEL0_TIMING = 0x6A08D082;
- PNX833X_MIU_SEL1_TIMING = 0x6A08D082;
-
- /* Setup GPIO 00 for use as MIU CS1 (CS0 is not multiplexed, so does not need this) */
- pnx833x_gpio_select_function_alt(0);
-#endif
-}
Remove another unused MIPS platform. Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> --- arch/mips/Kbuild.platforms | 1 - arch/mips/Kconfig | 30 --- arch/mips/configs/pnx8335_stb225_defconfig | 77 ------ arch/mips/include/asm/mach-pnx833x/gpio.h | 159 ------------ arch/mips/include/asm/mach-pnx833x/irq-mapping.h | 112 --------- arch/mips/include/asm/mach-pnx833x/irq.h | 40 --- arch/mips/include/asm/mach-pnx833x/pnx833x.h | 189 -------------- arch/mips/include/asm/mipsregs.h | 12 - arch/mips/pnx833x/Makefile | 4 - arch/mips/pnx833x/Platform | 4 - arch/mips/pnx833x/common/Makefile | 2 - arch/mips/pnx833x/common/interrupts.c | 303 ----------------------- arch/mips/pnx833x/common/platform.c | 224 ----------------- arch/mips/pnx833x/common/prom.c | 51 ---- arch/mips/pnx833x/common/reset.c | 31 --- arch/mips/pnx833x/common/setup.c | 48 ---- arch/mips/pnx833x/stb22x/Makefile | 2 - arch/mips/pnx833x/stb22x/board.c | 120 --------- 18 files changed, 1409 deletions(-) delete mode 100644 arch/mips/configs/pnx8335_stb225_defconfig delete mode 100644 arch/mips/include/asm/mach-pnx833x/gpio.h delete mode 100644 arch/mips/include/asm/mach-pnx833x/irq-mapping.h delete mode 100644 arch/mips/include/asm/mach-pnx833x/irq.h delete mode 100644 arch/mips/include/asm/mach-pnx833x/pnx833x.h delete mode 100644 arch/mips/pnx833x/Makefile delete mode 100644 arch/mips/pnx833x/Platform delete mode 100644 arch/mips/pnx833x/common/Makefile delete mode 100644 arch/mips/pnx833x/common/interrupts.c delete mode 100644 arch/mips/pnx833x/common/platform.c delete mode 100644 arch/mips/pnx833x/common/prom.c delete mode 100644 arch/mips/pnx833x/common/reset.c delete mode 100644 arch/mips/pnx833x/common/setup.c delete mode 100644 arch/mips/pnx833x/stb22x/Makefile delete mode 100644 arch/mips/pnx833x/stb22x/board.c