@@ -40,7 +40,12 @@ struct dw_mci_exynos_priv_data {
u32 sdr_timing;
u32 ddr_timing;
u32 hs200_timing;
+ u32 hs400_timing;
+ u32 tuned_sample;
u32 cur_speed;
+ u32 dqs_delay;
+ u32 saved_dqs_en;
+ u32 saved_strobe_ctrl;
};
static struct dw_mci_exynos_compatible {
@@ -90,6 +95,16 @@ static int dw_mci_exynos_priv_init(struct dw_mci *host)
SDMMC_MPSCTRL_NON_SECURE_WRITE_BIT);
}
+ if (priv->ctrl_type >= DW_MCI_TYPE_EXYNOS5420) {
+ priv->saved_strobe_ctrl = mci_readl(host, HS400_DLINE_CTRL);
+ priv->saved_dqs_en = mci_readl(host, HS400_DQS_EN);
+ priv->saved_dqs_en |= AXI_NON_BLOCKING_WR;
+ mci_writel(host, HS400_DQS_EN, priv->saved_dqs_en);
+ if (!priv->dqs_delay)
+ priv->dqs_delay =
+ DQS_CTRL_GET_RD_DELAY(priv->saved_strobe_ctrl);
+ }
+
priv->ciu_div = dw_mci_exynos_get_ciu_div(host);
return 0;
@@ -104,6 +119,14 @@ static int dw_mci_exynos_setup_clock(struct dw_mci *host)
return 0;
}
+static void dw_mci_exynos_set_clksel_timing(struct dw_mci *host, u32 timing)
+{
+ u32 clksel;
+ clksel = mci_readl(host, CLKSEL);
+ clksel = (clksel & ~SDMMC_CLKSEL_TIMING_MASK) | timing;
+ mci_writel(host, CLKSEL, clksel);
+}
+
#ifdef CONFIG_PM_SLEEP
static int dw_mci_exynos_suspend(struct device *dev)
{
@@ -161,23 +184,39 @@ static void dw_mci_exynos_prepare_command(struct dw_mci *host, u32 *cmdr)
*cmdr |= SDMMC_CMD_USE_HOLD_REG;
}
-static void dw_mci_exynos_set_ios(struct dw_mci *host, struct mmc_ios *ios)
+static void dw_mci_exynos_config_hs400(struct dw_mci *host, u32 timing)
{
struct dw_mci_exynos_priv_data *priv = host->priv;
- unsigned int wanted = ios->clock;
- unsigned long actual;
+ u32 dqs, strobe;
- if (ios->timing == MMC_TIMING_MMC_HS200) {
- mci_writel(host, CLKSEL, priv->hs200_timing);
- } else if (ios->timing == MMC_TIMING_MMC_DDR52) {
- mci_writel(host, CLKSEL, priv->ddr_timing);
- /* Should be double rate for DDR mode */
- if (ios->bus_width == MMC_BUS_WIDTH_8)
- wanted <<= 1;
+ /*
+ * Not suppported to configure register
+ * related to HS400
+ */
+ if (priv->ctrl_type < DW_MCI_TYPE_EXYNOS5420)
+ return;
+
+ dqs = priv->saved_dqs_en;
+ strobe = priv->saved_strobe_ctrl;
+
+ if (timing == MMC_TIMING_MMC_HS400) {
+ dqs |= DATA_STROBE_EN;
+ strobe = DQS_CTRL_RD_DELAY(strobe, priv->dqs_delay);
} else {
- mci_writel(host, CLKSEL, priv->sdr_timing);
+ dqs &= ~DATA_STROBE_EN;
}
+ mci_writel(host, HS400_DQS_EN, dqs);
+ mci_writel(host, HS400_DLINE_CTRL, strobe);
+}
+
+static void dw_mci_exynos_adjust_clock(struct dw_mci *host, unsigned int wanted)
+{
+ struct dw_mci_exynos_priv_data *priv = host->priv;
+ unsigned long actual;
+ u8 div;
+ int ret;
+
/*
* Don't care if wanted clock is zero or
* ciu clock is unavailable
@@ -189,18 +228,57 @@ static void dw_mci_exynos_set_ios(struct dw_mci *host, struct mmc_ios *ios)
if (wanted < EXYNOS_CCLKIN_MIN)
wanted = EXYNOS_CCLKIN_MIN;
- if (wanted != priv->cur_speed) {
- u8 div = dw_mci_exynos_get_ciu_div(host);
- int ret = clk_set_rate(host->ciu_clk, wanted * div);
- if (ret)
- dev_warn(host->dev,
- "failed to set clk-rate %u error: %d\n",
- wanted * div, ret);
- actual = clk_get_rate(host->ciu_clk);
- host->bus_hz = actual / div;
- priv->cur_speed = wanted;
- host->current_speed = 0;
+ if (wanted == priv->cur_speed)
+ return;
+
+ div = dw_mci_exynos_get_ciu_div(host);
+ ret = clk_set_rate(host->ciu_clk, wanted * div);
+ if (ret)
+ dev_warn(host->dev,
+ "failed to set clk-rate %u error: %d\n",
+ wanted * div, ret);
+ actual = clk_get_rate(host->ciu_clk);
+ host->bus_hz = actual / div;
+ priv->cur_speed = wanted;
+ host->current_speed = 0;
+}
+
+static void dw_mci_exynos_set_ios(struct dw_mci *host, struct mmc_ios *ios)
+{
+ struct dw_mci_exynos_priv_data *priv = host->priv;
+ unsigned int wanted = ios->clock;
+ u32 timing = ios->timing, clksel;
+
+ switch (timing) {
+ case MMC_TIMING_MMC_HS400:
+ /* Update tuned sample timing */
+ priv->hs400_timing = SDMMC_CLKSEL_UP_SAMPLE(
+ priv->hs400_timing, priv->tuned_sample);
+ case MMC_TIMING_MMC_HS400_TUNING:
+ clksel = priv->hs400_timing;
+ wanted <<= 1;
+ break;
+ case MMC_TIMING_MMC_HS200:
+ clksel = priv->hs200_timing;
+ break;
+ case MMC_TIMING_MMC_DDR52:
+ clksel = priv->ddr_timing;
+ /* Should be double rate for DDR mode */
+ if (ios->bus_width == MMC_BUS_WIDTH_8)
+ wanted <<= 1;
+ break;
+ default:
+ clksel = priv->sdr_timing;
}
+
+ /* Set clock timing for the requested speed mode*/
+ dw_mci_exynos_set_clksel_timing(host, clksel);
+
+ /* Configure setting for HS400 */
+ dw_mci_exynos_config_hs400(host, timing);
+
+ /* Configure clock rate */
+ dw_mci_exynos_adjust_clock(host, wanted);
}
static int dw_mci_exynos_dt_populate_timing(struct dw_mci *host,
@@ -256,6 +334,13 @@ static int dw_mci_exynos_parse_dt(struct dw_mci *host)
dw_mci_exynos_dt_populate_timing(host, priv->ctrl_type,
"samsung,dw-mshc-hs200-timing", &priv->hs200_timing);
+ ret = dw_mci_exynos_dt_populate_timing(host, priv->ctrl_type,
+ "samsung,dw-mshc-hs400-timing", &priv->hs400_timing);
+ if (!ret && of_property_read_u32(np,
+ "read-strobe-delay", &priv->dqs_delay))
+ dev_info(host->dev,
+ "read-strobe-delay is not found, assuming usage of default value\n");
+
host->priv = priv;
return 0;
@@ -270,7 +355,7 @@ static inline void dw_mci_exynos_set_clksmpl(struct dw_mci *host, u8 sample)
{
u32 clksel;
clksel = mci_readl(host, CLKSEL);
- clksel = (clksel & ~0x7) | SDMMC_CLKSEL_CCLK_SAMPLE(sample);
+ clksel = SDMMC_CLKSEL_UP_SAMPLE(clksel, sample);
mci_writel(host, CLKSEL, clksel);
}
@@ -281,7 +366,7 @@ static inline u8 dw_mci_exynos_move_next_clksmpl(struct dw_mci *host)
clksel = mci_readl(host, CLKSEL);
sample = (clksel + 1) & 0x7;
- clksel = (clksel & ~0x7) | sample;
+ clksel = SDMMC_CLKSEL_UP_SAMPLE(clksel, sample);
mci_writel(host, CLKSEL, clksel);
return sample;
}
@@ -316,6 +401,7 @@ static int dw_mci_exynos_execute_tuning(struct dw_mci_slot *slot, u32 opcode,
struct dw_mci_tuning_data *tuning_data)
{
struct dw_mci *host = slot->host;
+ struct dw_mci_exynos_priv_data *priv = host->priv;
struct mmc_host *mmc = slot->mmc;
const u8 *blk_pattern = tuning_data->blk_pattern;
u8 *blk_test;
@@ -373,10 +459,12 @@ static int dw_mci_exynos_execute_tuning(struct dw_mci_slot *slot, u32 opcode,
} while (start_smpl != smpl);
found = dw_mci_exynos_get_best_clksmpl(candiates);
- if (found >= 0)
+ if (found >= 0) {
dw_mci_exynos_set_clksmpl(host, found);
- else
+ priv->tuned_sample = found;
+ } else {
ret = -EIO;
+ }
kfree(blk_test);
return ret;
@@ -14,6 +14,9 @@
/* Extended Register's Offset */
#define SDMMC_CLKSEL 0x09C
+#define SDMMC_HS400_DQS_EN 0x180
+#define SDMMC_HS400_ASYNC_FIFO_CTRL 0x184
+#define SDMMC_HS400_DLINE_CTRL 0x188
/* CLKSEL register defines */
#define SDMMC_CLKSEL_CCLK_SAMPLE(x) (((x) & 7) << 0)
@@ -21,11 +24,22 @@
#define SDMMC_CLKSEL_CCLK_DIVIDER(x) (((x) & 7) << 24)
#define SDMMC_CLKSEL_GET_DRV_WD3(x) (((x) >> 16) & 0x7)
#define SDMMC_CLKSEL_GET_DIV(x) (((x) >> 24) & 0x7)
+#define SDMMC_CLKSEL_UP_SAMPLE(x, y) (((x) & ~SDMMC_CLKSEL_CCLK_SAMPLE(7)) |\
+ SDMMC_CLKSEL_CCLK_SAMPLE(y))
#define SDMMC_CLKSEL_TIMING(x, y, z) (SDMMC_CLKSEL_CCLK_SAMPLE(x) | \
SDMMC_CLKSEL_CCLK_DRIVE(y) | \
SDMMC_CLKSEL_CCLK_DIVIDER(z))
+#define SDMMC_CLKSEL_TIMING_MASK SDMMC_CLKSEL_TIMING(0x7, 0x7, 0x7)
#define SDMMC_CLKSEL_WAKEUP_INT BIT(11)
+/* HS400 control defines */
+#define DATA_STROBE_EN BIT(0)
+#define AXI_NON_BLOCKING_WR BIT(7)
+
+/* Delay Line Control defines */
+#define DQS_CTRL_RD_DELAY(x, y) (((x) & ~0x3FF) | ((y) & 0x3FF))
+#define DQS_CTRL_GET_RD_DELAY(x) ((x) & 0x3FF)
+
/* Protector Register */
#define SDMMC_EMMCP_BASE 0x1000
#define SDMMC_MPSECURITY (SDMMC_EMMCP_BASE + 0x0010)
@@ -953,7 +953,8 @@ static void dw_mci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
regs = mci_readl(slot->host, UHS_REG);
/* DDR mode set */
- if (ios->timing == MMC_TIMING_MMC_DDR52)
+ if (ios->timing == MMC_TIMING_MMC_DDR52 ||
+ ios->timing == MMC_TIMING_MMC_HS400)
regs |= ((0x1 << slot->id) << 16);
else
regs &= ~((0x1 << slot->id) << 16);
Implements HS400 support for exynos host driver. And this patch includes some updates as new mode is added. Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> --- drivers/mmc/host/dw_mmc-exynos.c | 140 +++++++++++++++++++++++++++++++------- drivers/mmc/host/dw_mmc-exynos.h | 14 ++++ drivers/mmc/host/dw_mmc.c | 3 +- 3 files changed, 130 insertions(+), 27 deletions(-)