@@ -130,6 +130,19 @@ config MMC_SDHCI_CNS3XXX
If unsure, say N.
+config MMC_SDHCI_IMX
+ tristate "Freescale i.MX platform eSDHCI support"
+ depends on ARCH_MX5 && MMC_SDHCI
+ depends on MMC_SDHCI_PLTFM
+ select MMC_SDHCI_IO_ACCESSORS
+ help
+ This selects the Freescale i.MX Enhanced Secure Card Host
+ Controller Interface.
+ If you have a i.MX platform with a Multimedia Card slot,
+ say Y or M here.
+
+ If unsure, say N.
+
config MMC_SDHCI_S3C
tristate "SDHCI support on Samsung S3C SoC"
depends on MMC_SDHCI && (PLAT_S3C24XX || PLAT_S3C64XX)
@@ -40,6 +40,7 @@ obj-$(CONFIG_MMC_JZ4740) += jz4740_mmc.o
obj-$(CONFIG_MMC_SDHCI_PLTFM) += sdhci-platform.o
sdhci-platform-y := sdhci-pltfm.o
sdhci-platform-$(CONFIG_MMC_SDHCI_CNS3XXX) += sdhci-cns3xxx.o
+sdhci-platform-$(CONFIG_MMC_SDHCI_IMX) += sdhci-imx.o
obj-$(CONFIG_MMC_SDHCI_OF) += sdhci-of.o
sdhci-of-y := sdhci-of-core.o
new file mode 100644
@@ -0,0 +1,395 @@
+/*
+ * Copyright (C) 2010 Freescale Semiconductor, Inc. All Rights Reserved.
+ */
+
+/*
+ * sdhci-imx.c Support for SDHCI platform devices
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+/* Supports:
+ * SDHCI imx devices
+ *
+ * Inspired by sdhci-pci.c, by Pierre Ossman
+ */
+
+#include <linux/delay.h>
+#include <linux/highmem.h>
+#include <linux/platform_device.h>
+#include <linux/clk.h>
+#include <linux/regulator/consumer.h>
+#include <linux/gpio.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/mmc/host.h>
+#include <linux/sdhci-pltfm.h>
+
+#include <mach/mmc.h>
+
+#include "sdhci.h"
+#include "sdhci-pltfm.h"
+
+/* Vendor specified registors */
+#define FSL_SDHCI_WML 0x44
+#define FSL_SDHCI_WML_16_WORDS 0x08100810
+#define FSL_SDHCI_WML_32_WORDS 0x08200820
+#define FSL_SDHCI_WML_64_WORDS 0x08400840
+#define FSL_SDHCI_WML_128_WORDS 0x08800880
+
+/* Non-standard clock control registor */
+#define ESDHC_SYSTEM_CONTROL 0x2C
+#define ESDHC_CLOCK_MASK 0x0000FFF0
+#define ESDHC_PREDIV_SHIFT 8
+#define ESDHC_DIVIDER_SHIFT 4
+#define ESDHC_CLOCK_PEREN 0x00000004
+#define ESDHC_CLOCK_HCKEN 0x00000002
+#define ESDHC_CLOCK_IPGEN 0x00000001
+
+/* Non-standard host control registor */
+#define ESDHC_SDHCI_CTRL_8BITBUS 0x00000004
+#define FSL_ESDHC_HOST_CONTROL_RES 0x33E
+#define ESDHC_HOST_CONTROL_LE 0x20
+
+/*****************************************************************************\
+ * *
+ * SDHCI core callbacks *
+ * *
+\*****************************************************************************/
+
+static u32 sdhci_imx_readl(struct sdhci_host *host, int reg)
+{
+ return readl(host->ioaddr + reg);
+}
+
+static u16 sdhci_imx_readw(struct sdhci_host *host, int reg)
+{
+ u32 val;
+ u16 rc;
+
+ if (reg % 4 == 3) {
+ printk(KERN_ERR "Invalid reg address!\n");
+ return 0;
+ }
+
+ val = readl(host->ioaddr + (reg / 4) * 4);
+ rc = (val >> (reg % 4) * 8) & 0xFFFF;
+
+ return rc;
+}
+
+static u8 sdhci_imx_readb(struct sdhci_host *host, int reg)
+{
+ u32 val;
+ u8 rc;
+
+ val = readl(host->ioaddr + (reg / 4) * 4);
+ rc = (val >> (reg % 4) * 8) & 0xFF;
+ if (reg == SDHCI_HOST_CONTROL) {
+ /* Bus width */
+ if (val & ESDHC_SDHCI_CTRL_8BITBUS) {
+ rc |= SDHCI_CTRL_8BITBUS;
+ rc &= ~SDHCI_CTRL_4BITBUS;
+ } else if (val & SDHCI_CTRL_4BITBUS) {
+ rc &= ~SDHCI_CTRL_8BITBUS;
+ rc |= SDHCI_CTRL_4BITBUS;
+ } else {
+ rc &= ~SDHCI_CTRL_8BITBUS;
+ rc &= ~SDHCI_CTRL_4BITBUS;
+ }
+ /* DMA */
+ if (val & (SDHCI_CTRL_DMA_MASK << 5))
+ rc |= ((val >> 5) & SDHCI_CTRL_DMA_MASK);
+ /* FIXME D3CD */
+ }
+
+ return rc;
+}
+
+static void sdhci_imx_writel(struct sdhci_host *host, u32 val, int reg)
+{
+ writel(val, host->ioaddr + reg);
+}
+
+static void sdhci_imx_writew(struct sdhci_host *host, u16 val, int reg)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+
+ u32 io_val;
+
+ if (reg % 4 == 3) {
+ printk(KERN_ERR "Invalid reg address!\n");
+ return;
+ }
+
+ if (reg == SDHCI_BLOCK_SIZE) {
+ /*
+ * Two last DMA bits are reserved, and first one is used for
+ * non-standard blksz of 4096 bytes that we don't support
+ * yet. So clear the DMA boundary bits.
+ */
+ val &= ~SDHCI_MAKE_BLKSZ(0x7, 0);
+ }
+
+ io_val = readl(host->ioaddr + (reg / 4) * 4);
+ io_val &= ~(0xFFFF << ((reg % 4) * 8));
+ io_val |= val << ((reg % 4) * 8);
+
+ switch (reg) {
+ case SDHCI_TRANSFER_MODE:
+ /*
+ * Postpone this write, we must do it together with a
+ * command write that is down below.
+ */
+ pltfm_host->scratchpad = val;
+ return;
+ case SDHCI_COMMAND:
+ writel(io_val | pltfm_host->scratchpad,
+ host->ioaddr + SDHCI_TRANSFER_MODE);
+ /*
+ * Make a double check that the warte mark level register is
+ * configured properly. default value is FSL_SDHCI_WML_16_WORDS
+ */
+ if (readl(host->ioaddr + FSL_SDHCI_WML)
+ == FSL_SDHCI_WML_16_WORDS) {
+ if (host->flags & SDHCI_REQ_USE_DMA)
+ writel(FSL_SDHCI_WML_64_WORDS,
+ host->ioaddr + FSL_SDHCI_WML);
+ else
+ writel(FSL_SDHCI_WML_128_WORDS,
+ host->ioaddr + FSL_SDHCI_WML);
+ }
+ return;
+ }
+
+ writel(io_val, host->ioaddr + (reg / 4) * 4);
+}
+
+static void sdhci_imx_set_power(struct sdhci_host *host, u8 power)
+{
+ int voltage = 0;
+
+ /* There is no sdhci standard PWR CTL REG in imx sdhci */
+ if (host->pwr == power)
+ return;
+
+ if (host->vmmc) {
+ if (power == (unsigned short)-1) {
+ regulator_disable(host->vmmc);
+ dev_dbg(mmc_dev(host->mmc), "mmc power off\n");
+ } else {
+ if (power == 7)
+ voltage = 1800000;
+ else if (power >= 8)
+ voltage = 2000000 + (power - 8) * 100000;
+ regulator_set_voltage(host->vmmc, voltage, voltage);
+
+ if (regulator_enable(host->vmmc) == 0) {
+ dev_dbg(mmc_dev(host->mmc), "mmc power on\n");
+ msleep(1);
+ }
+ }
+ }
+
+ host->pwr = power;
+}
+
+static void sdhci_imx_writeb(struct sdhci_host *host, u8 val, int reg)
+{
+ u32 io_val;
+
+ /* Since there is no power register in FSL eSDHC, handle it in SW */
+ if (reg == SDHCI_POWER_CONTROL) {
+ sdhci_imx_set_power(host, val);
+ return;
+ }
+
+ if (reg == SDHCI_HOST_CONTROL) {
+ io_val = readl(host->ioaddr + SDHCI_HOST_CONTROL);
+ /* Bit7~6, andi bit0 */
+ io_val |= (val & ~FSL_ESDHC_HOST_CONTROL_RES);
+ /* Ensure the LE mode */
+ io_val |= ESDHC_HOST_CONTROL_LE;
+ /* Configure the bus_width 8bits, 4bits, or 1bit*/
+ if (val & SDHCI_CTRL_8BITBUS) {
+ io_val |= ESDHC_SDHCI_CTRL_8BITBUS;
+ io_val &= ~SDHCI_CTRL_4BITBUS;
+ } else if (val & SDHCI_CTRL_4BITBUS) {
+ io_val &= ~ESDHC_SDHCI_CTRL_8BITBUS;
+ io_val |= SDHCI_CTRL_4BITBUS;
+ } else {
+ io_val &= ~ESDHC_SDHCI_CTRL_8BITBUS;
+ io_val &= ~SDHCI_CTRL_4BITBUS;
+ }
+
+ /* Configure the DMA */
+ if (val & SDHCI_CTRL_DMA_MASK)
+ io_val |= (val & SDHCI_CTRL_DMA_MASK) << 5;
+ writel(io_val, host->ioaddr + SDHCI_HOST_CONTROL);
+
+ return;
+ }
+
+ io_val = readl(host->ioaddr + (reg / 4) * 4);
+ io_val &= ~(0xFF << ((reg % 4) * 8));
+ io_val |= val << ((reg % 4) * 8);
+
+ writel(io_val, host->ioaddr + (reg / 4) * 4);
+}
+
+static unsigned int sdhci_imx_get_max_clock(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+
+ return clk_get_rate(pltfm_host->clk);
+}
+
+static unsigned int sdhci_imx_get_min_clock(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+
+ return clk_get_rate(pltfm_host->clk) / 256 / 16;
+}
+
+static unsigned int sdhci_imx_get_timeout_clock(struct sdhci_host *host)
+{
+ return sdhci_imx_get_max_clock(host) / 1000000;
+}
+
+static unsigned int sdhci_imx_get_ro(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+
+ return gpio_get_value(pltfm_host->wp_gpio);
+}
+
+static void sdhci_imx_set_clock(struct sdhci_host *host, unsigned int clock)
+{
+ int pre_div = 2;
+ int div = 1;
+ u32 temp;
+
+ temp = sdhci_readl(host, ESDHC_SYSTEM_CONTROL);
+ temp &= ~(ESDHC_CLOCK_IPGEN | ESDHC_CLOCK_HCKEN | ESDHC_CLOCK_PEREN
+ | ESDHC_CLOCK_MASK);
+ sdhci_writel(host, temp, ESDHC_SYSTEM_CONTROL);
+
+ if (clock == 0)
+ goto out;
+
+ while (host->max_clk / pre_div / 16 > clock && pre_div < 256)
+ pre_div *= 2;
+
+ while (host->max_clk / pre_div / div > clock && div < 16)
+ div++;
+
+ dev_dbg(mmc_dev(host->mmc), "desired SD clock: %d, actual: %d\n",
+ clock, host->max_clk / pre_div / div);
+
+ pre_div >>= 1;
+ div--;
+
+ temp = sdhci_readl(host, ESDHC_SYSTEM_CONTROL);
+ temp |= (ESDHC_CLOCK_IPGEN | ESDHC_CLOCK_HCKEN | ESDHC_CLOCK_PEREN
+ | (div << ESDHC_DIVIDER_SHIFT)
+ | (pre_div << ESDHC_PREDIV_SHIFT));
+ sdhci_writel(host, temp, ESDHC_SYSTEM_CONTROL);
+ mdelay(10);
+out:
+ host->clock = clock;
+}
+
+static int sdhci_imx_enable_dma(struct sdhci_host *host)
+{
+ u32 ctrl;
+
+ ctrl = readl(host->ioaddr + SDHCI_HOST_CONTROL);
+ ctrl &= ~(SDHCI_CTRL_DMA_MASK << 5);
+ if ((host->flags & SDHCI_REQ_USE_DMA) &&
+ (host->flags & SDHCI_USE_ADMA))
+ ctrl |= (SDHCI_CTRL_ADMA32 << 8);
+ else if (host->flags & SDHCI_REQ_USE_DMA)
+ ctrl |= (SDHCI_CTRL_SDMA << 8);
+
+ writel(ctrl, host->ioaddr + SDHCI_HOST_CONTROL);
+
+ if (host->flags & SDHCI_REQ_USE_DMA)
+ writel(FSL_SDHCI_WML_64_WORDS,
+ host->ioaddr + FSL_SDHCI_WML);
+ else
+ writel(FSL_SDHCI_WML_128_WORDS,
+ host->ioaddr + FSL_SDHCI_WML);
+ return 0;
+}
+
+static int __match_sdhci_imx(struct device *dev, void *data)
+{
+ return !strncmp(dev_name(dev), "imx-sdhci", 9);
+}
+static int sdhci_imx_init(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct clk *clk;
+ struct device *dev;
+
+ dev = device_find_child(mmc_dev(host->mmc), NULL, __match_sdhci_imx);
+ clk = clk_get(dev, "imx_sdhc_clk");
+ if (IS_ERR(clk)) {
+ dev_err(mmc_dev(host->mmc), "clk err\n");
+ return -ENODEV;
+ }
+ clk_enable(clk);
+ pltfm_host->clk = clk;
+ dev_dbg(dev, "SDHC clock:%lu\n", clk_get_rate(clk));
+
+ return 0;
+}
+
+static void sdhci_imx_exit(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+
+ clk_disable(pltfm_host->clk);
+ clk_put(pltfm_host->clk);
+}
+
+
+static struct sdhci_ops sdhci_imx_ops = {
+ .read_l = sdhci_imx_readl,
+ .read_w = sdhci_imx_readw,
+ .read_b = sdhci_imx_readb,
+ .write_l = sdhci_imx_writel,
+ .write_w = sdhci_imx_writew,
+ .write_b = sdhci_imx_writeb,
+ .set_clock = sdhci_imx_set_clock,
+ .enable_dma = sdhci_imx_enable_dma,
+ .get_max_clock = sdhci_imx_get_max_clock,
+ .get_min_clock = sdhci_imx_get_min_clock,
+ .get_timeout_clock = sdhci_imx_get_timeout_clock,
+ .get_ro = sdhci_imx_get_ro,
+};
+
+struct sdhci_pltfm_data sdhci_imx_pdata = {
+ .ops = &sdhci_imx_ops,
+ .quirks = SDHCI_QUIRK_BROKEN_ADMA
+ | SDHCI_QUIRK_32BIT_DMA_ADDR
+ | SDHCI_QUIRK_32BIT_ADMA_SIZE
+ | SDHCI_QUIRK_BROKEN_TIMEOUT_VAL
+ | SDHCI_QUIRK_NO_BUSY_IRQ
+ | SDHCI_QUIRK_BROKEN_CARD_DETECTION
+ | SDHCI_QUIRK_NONSTANDARD_CLOCK
+ | SDHCI_QUIRK_RESTORE_IRQS_AFTER_RESET,
+ .init = sdhci_imx_init,
+ .exit = sdhci_imx_exit,
+};