@@ -40,7 +40,6 @@
static unsigned int debug_quirks = 0;
-static void sdhci_prepare_data(struct sdhci_host *, struct mmc_data *);
static void sdhci_finish_data(struct sdhci_host *);
static void sdhci_send_command(struct sdhci_host *, struct mmc_command *);
@@ -591,9 +590,10 @@ static void sdhci_adma_table_post(struct sdhci_host *host,
data->sg_len, direction);
}
-static u8 sdhci_calc_timeout(struct sdhci_host *host, struct mmc_data *data)
+static u8 sdhci_calc_timeout(struct sdhci_host *host, struct mmc_command *cmd)
{
u8 count;
+ struct mmc_data *data = cmd->data;
unsigned target_timeout, current_timeout;
/*
@@ -605,12 +605,16 @@ static u8 sdhci_calc_timeout(struct sdhci_host *host, struct mmc_data *data)
if (host->quirks & SDHCI_QUIRK_BROKEN_TIMEOUT_VAL)
return 0xE;
- /* timeout in us */
- target_timeout = data->timeout_ns / 1000 +
- data->timeout_clks / host->clock;
+ /* Unspecified timeout, assume max */
+ if (!data && !cmd->cmd_timeout)
+ return 0xE;
- if (host->quirks & SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK)
- host->timeout_clk = host->clock / 1000;
+ /* timeout in us */
+ if (!data)
+ target_timeout = cmd->cmd_timeout * 1000;
+ else
+ target_timeout = data->timeout_ns / 1000 +
+ data->timeout_clks / host->clock;
/*
* Figure out needed cycles.
@@ -632,8 +636,9 @@ static u8 sdhci_calc_timeout(struct sdhci_host *host, struct mmc_data *data)
}
if (count >= 0xF) {
- printk(KERN_WARNING "%s: Too large timeout requested!\n",
- mmc_hostname(host->mmc));
+ printk(KERN_WARNING "%s: Too large timeout requested for CMD%d!\n",
+ mmc_hostname(host->mmc),
+ cmd->opcode);
count = 0xE;
}
@@ -651,15 +656,21 @@ static void sdhci_set_transfer_irqs(struct sdhci_host *host)
sdhci_clear_set_irqs(host, dma_irqs, pio_irqs);
}
-static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_data *data)
+static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_command *cmd)
{
u8 count;
u8 ctrl;
+ struct mmc_data *data = cmd->data;
int ret;
WARN_ON(host->data);
- if (data == NULL)
+ if (data || (cmd->flags & MMC_RSP_BUSY)) {
+ count = sdhci_calc_timeout(host, cmd);
+ sdhci_writeb(host, count, SDHCI_TIMEOUT_CONTROL);
+ }
+
+ if (!data)
return;
/* Sanity checks */
@@ -670,9 +681,6 @@ static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_data *data)
host->data = data;
host->data_early = 0;
- count = sdhci_calc_timeout(host, data);
- sdhci_writeb(host, count, SDHCI_TIMEOUT_CONTROL);
-
if (host->flags & (SDHCI_USE_SDMA | SDHCI_USE_ADMA))
host->flags |= SDHCI_REQ_USE_DMA;
@@ -920,7 +928,7 @@ static void sdhci_send_command(struct sdhci_host *host, struct mmc_command *cmd)
host->cmd = cmd;
- sdhci_prepare_data(host, cmd->data);
+ sdhci_prepare_data(host, cmd);
sdhci_writel(host, cmd->arg, SDHCI_ARGUMENT);
@@ -1867,6 +1875,9 @@ int sdhci_add_host(struct sdhci_host *host)
if (caps & SDHCI_TIMEOUT_CLK_UNIT)
host->timeout_clk *= 1000;
+ if (host->quirks & SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK)
+ host->timeout_clk = host->clock / 1000;
+
/*
* Set host parameters.
*/
@@ -1879,7 +1890,7 @@ int sdhci_add_host(struct sdhci_host *host)
mmc->f_min = host->max_clk / SDHCI_MAX_DIV_SPEC_200;
mmc->f_max = host->max_clk;
- mmc->caps |= MMC_CAP_SDIO_IRQ;
+ mmc->caps |= MMC_CAP_SDIO_IRQ | MMC_CAP_ERASE;
/*
* A controller may support 8-bit width, but the board itself
ERASE command needs R1B response, so fix R1B-type command handling for SDHCI controller. For non-DAT commands using a busy reponse, the cmd->cmd_timeout (in ms) field is used for timeout calculations. Based on patch by Chuanxiao Dong <chuanxiao.dong@intel.com> Signed-off-by: Andrei Warkentin <andreiw@motorola.com> --- drivers/mmc/host/sdhci.c | 43 +++++++++++++++++++++++++++---------------- 1 files changed, 27 insertions(+), 16 deletions(-)