@@ -942,6 +942,40 @@ u32 mmc_select_voltage(struct mmc_host *host, u32 ocr)
return ocr;
}
+int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage)
+{
+ struct mmc_command cmd;
+ int err = 0;
+
+ BUG_ON(!host);
+
+ /*
+ * Send CMD11 only if the request is to switch the card to
+ * 1.8V signalling.
+ */
+ if (signal_voltage == MMC_SIGNAL_VOLTAGE_180) {
+ memset(&cmd, 0, sizeof(struct mmc_command));
+
+ cmd.opcode = SD_SWITCH_VOLTAGE;
+ cmd.arg = 0;
+ cmd.flags = MMC_RSP_R1 | MMC_CMD_AC;
+
+ err = mmc_wait_for_cmd(host, &cmd, 0);
+ if (err)
+ return err;
+
+ if (!mmc_host_is_spi(host) && (cmd.resp[0] & R1_ERROR))
+ return -EIO;
+ }
+
+ host->ios.signal_voltage = signal_voltage;
+
+ if (host->ops->start_signal_voltage_switch)
+ err = host->ops->start_signal_voltage_switch(host, &host->ios);
+
+ return err;
+}
+
/*
* Select timing parameters for host.
*/
@@ -41,6 +41,7 @@ void mmc_set_bus_width(struct mmc_host *host, unsigned int width);
void mmc_set_bus_width_ddr(struct mmc_host *host, unsigned int width,
unsigned int ddr);
u32 mmc_select_voltage(struct mmc_host *host, u32 ocr);
+int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage);
void mmc_set_timing(struct mmc_host *host, unsigned int timing);
static inline void mmc_delay(unsigned int ms)
@@ -403,6 +403,7 @@ struct device_type sd_type = {
int mmc_sd_get_cid(struct mmc_host *host, u32 ocr, u32 *cid)
{
int err;
+ u32 rocr;
/*
* Since we're changing the OCR value, we seem to
@@ -420,12 +421,38 @@ int mmc_sd_get_cid(struct mmc_host *host, u32 ocr, u32 *cid)
*/
err = mmc_send_if_cond(host, ocr);
if (!err)
- ocr |= 1 << 30;
+ ocr |= SD_OCR_CCS;
- err = mmc_send_app_op_cond(host, ocr, NULL);
+ /*
+ * If the host supports one of UHS-I modes, request the card
+ * to switch to 1.8V signaling level.
+ */
+ if (host->caps & (MMC_CAP_UHS_SDR12 | MMC_CAP_UHS_SDR25 |
+ MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR104 | MMC_CAP_UHS_DDR50))
+ ocr |= SD_OCR_S18R;
+
+ /* If the host can supply more than 150mA, XPC should be set to 1. */
+ if (host->caps & (MMC_CAP_SET_XPC_330 | MMC_CAP_SET_XPC_300 |
+ MMC_CAP_SET_XPC_180))
+ ocr |= SD_OCR_XPC;
+
+try_again:
+ err = mmc_send_app_op_cond(host, ocr, &rocr);
if (err)
return err;
+ /*
+ * In case CCS and S18A in the response is set, start Signal Voltage
+ * Switch procedure. SPI mode doesn't support CMD11.
+ */
+ if (!mmc_host_is_spi(host) && ((rocr & 0x41000000) == 0x41000000)) {
+ err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180);
+ if (err) {
+ ocr &= ~SD_OCR_S18R;
+ goto try_again;
+ }
+ }
+
if (mmc_host_is_spi(host))
err = mmc_send_cid(host, cid);
else
@@ -773,6 +800,11 @@ int mmc_attach_sd(struct mmc_host *host)
BUG_ON(!host);
WARN_ON(!host->claimed);
+ /* Make sure we are at 3.3V signalling voltage */
+ err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330);
+ if (err)
+ return err;
+
err = mmc_send_app_op_cond(host, 0, &ocr);
if (err)
return err;
@@ -83,6 +83,8 @@ static void sdhci_dumpregs(struct sdhci_host *host)
printk(KERN_DEBUG DRIVER_NAME ": Cmd: 0x%08x | Max curr: 0x%08x\n",
sdhci_readw(host, SDHCI_COMMAND),
sdhci_readl(host, SDHCI_MAX_CURRENT));
+ printk(KERN_DEBUG DRIVER_NAME ": Host ctl2: 0x%08x\n",
+ sdhci_readw(host, SDHCI_HOST_CONTROL2));
if (host->flags & SDHCI_USE_ADMA)
printk(KERN_DEBUG DRIVER_NAME ": ADMA Err: 0x%08x | ADMA Ptr: 0x%08x\n",
@@ -1323,11 +1325,115 @@ out:
spin_unlock_irqrestore(&host->lock, flags);
}
+static int sdhci_start_signal_voltage_switch(struct mmc_host *mmc,
+ struct mmc_ios *ios)
+{
+ struct sdhci_host *host;
+ u8 pwr;
+ u16 clk, ctrl;
+ u32 present_state;
+
+ host = mmc_priv(mmc);
+
+ /*
+ * Signal Voltage Switching is only applicable for Host Controllers
+ * v3.00 and above.
+ */
+ if (host->version < SDHCI_SPEC_300)
+ return 0;
+
+ /*
+ * We first check whether the request is to set signalling voltage
+ * to 3.3V. If so, we change the voltage to 3.3V and return quickly.
+ */
+ ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
+ if (ios->signal_voltage == MMC_SIGNAL_VOLTAGE_330) {
+ /* Set 1.8V Signal Enable in the Host Control2 register to 0 */
+ ctrl &= ~SDHCI_CTRL_VDD_180;
+ sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
+
+ /* Wait for 5ms */
+ usleep_range(5000, 5500);
+
+ /* 3.3V regulator output should be stable within 5 ms */
+ ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
+ if (!(ctrl & SDHCI_CTRL_VDD_180))
+ return 0;
+ else {
+ printk(KERN_INFO DRIVER_NAME ": Switching to 3.3V "
+ "signalling voltage failed\n");
+ return -EIO;
+ }
+ } else if (!(ctrl & SDHCI_CTRL_VDD_180) &&
+ (ios->signal_voltage == MMC_SIGNAL_VOLTAGE_180)) {
+ /* Stop SDCLK */
+ clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
+ clk &= ~SDHCI_CLOCK_CARD_EN;
+ sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
+
+ /* Check whether DAT[3:0] is 0000 */
+ present_state = sdhci_readl(host, SDHCI_PRESENT_STATE);
+ if (!((present_state & SDHCI_DATA_LVL_MASK) >>
+ SDHCI_DATA_LVL_SHIFT)) {
+ /*
+ * Enable 1.8V Signal Enable in the Host Control2
+ * register
+ */
+ ctrl |= SDHCI_CTRL_VDD_180;
+ sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
+
+ /* Wait for 5ms */
+ usleep_range(5000, 5500);
+
+ ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
+ if (ctrl & SDHCI_CTRL_VDD_180) {
+ /* Provide SDCLK again and wait for 1ms*/
+ clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
+ clk |= SDHCI_CLOCK_CARD_EN;
+ sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
+ usleep_range(1000, 1500);
+
+ /*
+ * If DAT[3:0] level is 1111b, then the card
+ * was successfully switched to 1.8V signaling.
+ */
+ present_state = sdhci_readl(host,
+ SDHCI_PRESENT_STATE);
+ if ((present_state & SDHCI_DATA_LVL_MASK) ==
+ SDHCI_DATA_LVL_MASK) {
+ return 0;
+ }
+ }
+ }
+
+ /*
+ * If we are here, that means the switch to 1.8V signaling
+ * failed. We power cycle the card, and retry initialization
+ * sequence by setting S18R to 0.
+ */
+ pwr = sdhci_readb(host, SDHCI_POWER_CONTROL);
+ pwr &= ~SDHCI_POWER_ON;
+ sdhci_writeb(host, pwr, SDHCI_POWER_CONTROL);
+
+ /* Wait for 1ms as per the spec */
+ usleep_range(1000, 1500);
+ pwr |= SDHCI_POWER_ON;
+ sdhci_writeb(host, pwr, SDHCI_POWER_CONTROL);
+
+ printk(KERN_INFO DRIVER_NAME ": Switching to 1.8V signalling "
+ "voltage failed, retrying with S18R set to 0\n");
+ return -EAGAIN;
+ } else
+ /* No signal voltage switch required */
+ return 0;
+}
+
static const struct mmc_host_ops sdhci_ops = {
.request = sdhci_request,
.set_ios = sdhci_set_ios,
.get_ro = sdhci_get_ro,
.enable_sdio_irq = sdhci_enable_sdio_irq,
+ .start_signal_voltage_switch = sdhci_start_signal_voltage_switch,
};
/*****************************************************************************\
@@ -1808,7 +1914,9 @@ EXPORT_SYMBOL_GPL(sdhci_alloc_host);
int sdhci_add_host(struct sdhci_host *host)
{
struct mmc_host *mmc;
- unsigned int caps, ocr_avail;
+ u32 caps[2];
+ u32 max_current_caps;
+ unsigned int ocr_avail;
int ret;
WARN_ON(host == NULL);
@@ -1831,12 +1939,15 @@ int sdhci_add_host(struct sdhci_host *host)
host->version);
}
- caps = (host->quirks & SDHCI_QUIRK_MISSING_CAPS) ? host->caps :
+ caps[0] = (host->quirks & SDHCI_QUIRK_MISSING_CAPS) ? host->caps :
sdhci_readl(host, SDHCI_CAPABILITIES);
+ caps[1] = (host->version >= SDHCI_SPEC_300) ?
+ sdhci_readl(host, SDHCI_CAPABILITIES_1) : 0;
+
if (host->quirks & SDHCI_QUIRK_FORCE_DMA)
host->flags |= SDHCI_USE_SDMA;
- else if (!(caps & SDHCI_CAN_DO_SDMA))
+ else if (!(caps[0] & SDHCI_CAN_DO_SDMA))
DBG("Controller doesn't have SDMA capability\n");
else
host->flags |= SDHCI_USE_SDMA;
@@ -1847,7 +1958,8 @@ int sdhci_add_host(struct sdhci_host *host)
host->flags &= ~SDHCI_USE_SDMA;
}
- if ((host->version >= SDHCI_SPEC_200) && (caps & SDHCI_CAN_DO_ADMA2))
+ if ((host->version >= SDHCI_SPEC_200) &&
+ (caps[0] & SDHCI_CAN_DO_ADMA2))
host->flags |= SDHCI_USE_ADMA;
if ((host->quirks & SDHCI_QUIRK_BROKEN_ADMA) &&
@@ -1897,10 +2009,10 @@ int sdhci_add_host(struct sdhci_host *host)
}
if (host->version >= SDHCI_SPEC_300)
- host->max_clk = (caps & SDHCI_CLOCK_V3_BASE_MASK)
+ host->max_clk = (caps[0] & SDHCI_CLOCK_V3_BASE_MASK)
>> SDHCI_CLOCK_BASE_SHIFT;
else
- host->max_clk = (caps & SDHCI_CLOCK_BASE_MASK)
+ host->max_clk = (caps[0] & SDHCI_CLOCK_BASE_MASK)
>> SDHCI_CLOCK_BASE_SHIFT;
host->max_clk *= 1000000;
@@ -1916,7 +2028,7 @@ int sdhci_add_host(struct sdhci_host *host)
}
host->timeout_clk =
- (caps & SDHCI_TIMEOUT_CLK_MASK) >> SDHCI_TIMEOUT_CLK_SHIFT;
+ (caps[0] & SDHCI_TIMEOUT_CLK_MASK) >> SDHCI_TIMEOUT_CLK_SHIFT;
if (host->timeout_clk == 0) {
if (host->ops->get_timeout_clock) {
host->timeout_clk = host->ops->get_timeout_clock(host);
@@ -1928,7 +2040,7 @@ int sdhci_add_host(struct sdhci_host *host)
return -ENODEV;
}
}
- if (caps & SDHCI_TIMEOUT_CLK_UNIT)
+ if (caps[0] & SDHCI_TIMEOUT_CLK_UNIT)
host->timeout_clk *= 1000;
/*
@@ -1955,21 +2067,76 @@ int sdhci_add_host(struct sdhci_host *host)
if (!(host->quirks & SDHCI_QUIRK_FORCE_1_BIT_DATA))
mmc->caps |= MMC_CAP_4_BIT_DATA;
- if (caps & SDHCI_CAN_DO_HISPD)
+ if (caps[0] & SDHCI_CAN_DO_HISPD)
mmc->caps |= MMC_CAP_SD_HIGHSPEED | MMC_CAP_MMC_HIGHSPEED;
if ((host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION) &&
mmc_card_is_removable(mmc))
mmc->caps |= MMC_CAP_NEEDS_POLL;
+ /* UHS-I mode(s) supported by the host controller. */
+ if (host->version >= SDHCI_SPEC_300)
+ mmc->caps |= MMC_CAP_UHS_SDR12 | MMC_CAP_UHS_SDR25;
+
+ /* SDR104 supports also implies SDR50 support */
+ if (caps[1] & SDHCI_SUPPORT_SDR104)
+ mmc->caps |= MMC_CAP_UHS_SDR104 | MMC_CAP_UHS_SDR50;
+ else if (caps[1] & SDHCI_SUPPORT_SDR50)
+ mmc->caps |= MMC_CAP_UHS_SDR50;
+
+ if (caps[1] & SDHCI_SUPPORT_DDR50)
+ mmc->caps |= MMC_CAP_UHS_DDR50;
+
ocr_avail = 0;
- if (caps & SDHCI_CAN_VDD_330)
+ /*
+ * According to SD Host Controller spec v3.00, if the Host System
+ * can afford more than 150mA, Host Driver should set XPC to 1. Also
+ * the value is meaningful only if Voltage Support in the Capabilities
+ * register is set. The actual current value is 4 times the register
+ * value.
+ */
+ max_current_caps = sdhci_readl(host, SDHCI_MAX_CURRENT);
+
+ if (caps[0] & SDHCI_CAN_VDD_330) {
+ int max_current_330;
+
ocr_avail |= MMC_VDD_32_33 | MMC_VDD_33_34;
- if (caps & SDHCI_CAN_VDD_300)
+
+ max_current_330 = ((max_current_caps &
+ SDHCI_MAX_CURRENT_330_MASK) >>
+ SDHCI_MAX_CURRENT_330_SHIFT) *
+ SDHCI_MAX_CURRENT_MULTIPLIER;
+
+ if (max_current_330 > 150)
+ mmc->caps |= MMC_CAP_SET_XPC_330;
+ }
+ if (caps[0] & SDHCI_CAN_VDD_300) {
+ int max_current_300;
+
ocr_avail |= MMC_VDD_29_30 | MMC_VDD_30_31;
- if (caps & SDHCI_CAN_VDD_180)
+
+ max_current_300 = ((max_current_caps &
+ SDHCI_MAX_CURRENT_300_MASK) >>
+ SDHCI_MAX_CURRENT_300_SHIFT) *
+ SDHCI_MAX_CURRENT_MULTIPLIER;
+
+ if (max_current_300 > 150)
+ mmc->caps |= MMC_CAP_SET_XPC_300;
+ }
+ if (caps[0] & SDHCI_CAN_VDD_180) {
+ int max_current_180;
+
ocr_avail |= MMC_VDD_165_195;
+ max_current_180 = ((max_current_caps &
+ SDHCI_MAX_CURRENT_180_MASK) >>
+ SDHCI_MAX_CURRENT_180_SHIFT) *
+ SDHCI_MAX_CURRENT_MULTIPLIER;
+
+ if (max_current_180 > 150)
+ mmc->caps |= MMC_CAP_SET_XPC_180;
+ }
+
mmc->ocr_avail = ocr_avail;
mmc->ocr_avail_sdio = ocr_avail;
if (host->ocr_avail_sdio)
@@ -2029,7 +2196,7 @@ int sdhci_add_host(struct sdhci_host *host)
if (host->quirks & SDHCI_QUIRK_FORCE_BLK_SZ_2048) {
mmc->max_blk_size = 2;
} else {
- mmc->max_blk_size = (caps & SDHCI_MAX_BLOCK_MASK) >>
+ mmc->max_blk_size = (caps[0] & SDHCI_MAX_BLOCK_MASK) >>
SDHCI_MAX_BLOCK_SHIFT;
if (mmc->max_blk_size >= 3) {
printk(KERN_WARNING "%s: Invalid maximum block size, "
@@ -68,6 +68,8 @@
#define SDHCI_DATA_AVAILABLE 0x00000800
#define SDHCI_CARD_PRESENT 0x00010000
#define SDHCI_WRITE_PROTECT 0x00080000
+#define SDHCI_DATA_LVL_MASK 0x00F00000
+#define SDHCI_DATA_LVL_SHIFT 20
#define SDHCI_HOST_CONTROL 0x28
#define SDHCI_CTRL_LED 0x01
@@ -146,7 +148,8 @@
#define SDHCI_ACMD12_ERR 0x3C
-/* 3E-3F reserved */
+#define SDHCI_HOST_CONTROL2 0x3E
+#define SDHCI_CTRL_VDD_180 0x0008
#define SDHCI_CAPABILITIES 0x40
#define SDHCI_TIMEOUT_CLK_MASK 0x0000003F
@@ -167,9 +170,20 @@
#define SDHCI_CAN_VDD_180 0x04000000
#define SDHCI_CAN_64BIT 0x10000000
+#define SDHCI_SUPPORT_SDR50 0x00000001
+#define SDHCI_SUPPORT_SDR104 0x00000002
+#define SDHCI_SUPPORT_DDR50 0x00000004
+
#define SDHCI_CAPABILITIES_1 0x44
-#define SDHCI_MAX_CURRENT 0x48
+#define SDHCI_MAX_CURRENT 0x48
+#define SDHCI_MAX_CURRENT_330_MASK 0x0000FF
+#define SDHCI_MAX_CURRENT_330_SHIFT 0
+#define SDHCI_MAX_CURRENT_300_MASK 0x00FF00
+#define SDHCI_MAX_CURRENT_300_SHIFT 8
+#define SDHCI_MAX_CURRENT_180_MASK 0xFF0000
+#define SDHCI_MAX_CURRENT_180_SHIFT 16
+#define SDHCI_MAX_CURRENT_MULTIPLIER 4
/* 4C-4F reserved for more max current */
@@ -56,6 +56,11 @@ struct mmc_ios {
#define MMC_SDR_MODE 0
#define MMC_1_2V_DDR_MODE 1
#define MMC_1_8V_DDR_MODE 2
+
+ unsigned char signal_voltage; /* signalling voltage (1.8V or 3.3V) */
+
+#define MMC_SIGNAL_VOLTAGE_330 0
+#define MMC_SIGNAL_VOLTAGE_180 1
};
struct mmc_host_ops {
@@ -117,6 +122,8 @@ struct mmc_host_ops {
/* optional callback for HC quirks */
void (*init_card)(struct mmc_host *host, struct mmc_card *card);
+
+ int (*start_signal_voltage_switch)(struct mmc_host *host, struct mmc_ios *ios);
};
struct mmc_card;
@@ -173,6 +180,14 @@ struct mmc_host {
/* DDR mode at 1.2V */
#define MMC_CAP_POWER_OFF_CARD (1 << 13) /* Can power off after boot */
#define MMC_CAP_BUS_WIDTH_TEST (1 << 14) /* CMD14/CMD19 bus width ok */
+#define MMC_CAP_UHS_SDR12 (1 << 15) /* Host supports UHS SDR12 mode */
+#define MMC_CAP_UHS_SDR25 (1 << 16) /* Host supports UHS SDR25 mode */
+#define MMC_CAP_UHS_SDR50 (1 << 17) /* Host supports UHS SDR50 mode */
+#define MMC_CAP_UHS_SDR104 (1 << 18) /* Host supports UHS SDR104 mode */
+#define MMC_CAP_UHS_DDR50 (1 << 19) /* Host supports UHS DDR50 mode */
+#define MMC_CAP_SET_XPC_330 (1 << 20) /* Host supports >150mA current at 3.3V */
+#define MMC_CAP_SET_XPC_300 (1 << 21) /* Host supports >150mA current at 3.0V */
+#define MMC_CAP_SET_XPC_180 (1 << 22) /* Host supports >150mA current at 1.8V */
mmc_pm_flag_t pm_caps; /* supported pm features */
@@ -17,6 +17,7 @@
/* This is basically the same command as for MMC with some quirks. */
#define SD_SEND_RELATIVE_ADDR 3 /* bcr R6 */
#define SD_SEND_IF_COND 8 /* bcr [11:0] See below R7 */
+#define SD_SWITCH_VOLTAGE 11 /* ac R1 */
/* class 10 */
#define SD_SWITCH 6 /* adtc [31:0] See below R1 */
@@ -32,6 +33,12 @@
#define SD_APP_OP_COND 41 /* bcr [31:0] OCR R3 */
#define SD_APP_SEND_SCR 51 /* adtc R1 */
+/* OCR bit definitions */
+#define SD_OCR_S18R (1 << 24) /* 1.8V switching request */
+#define SD_ROCR_S18A SD_OCR_S18R /* 1.8V switching accepted by card */
+#define SD_OCR_XPC (1 << 28) /* SDXC power control */
+#define SD_OCR_CCS (1 << 30) /* Card Capacity Status */
+
/*
* SD_SWITCH argument format:
*