new file mode 100644
@@ -0,0 +1,49 @@
+Qualcomm Standard Secure Digital Host Controller (SDHC)
+
+Secure Digital Host Controller provides standard host interface to SD/MMC/SDIO cards.
+
+Required properties:
+ - compatible : should be "qcom,sdhci-msm"
+ - reg : should contain SDHC, SD Core register map.
+ - reg-names : indicates various resources passed to driver (via reg proptery) by name.
+ "reg-names" examples are "hc_mem" and "core_mem"
+ - interrupts : should contain SDHC interrupts.
+ - interrupt-names : indicates interrupts passed to driver (via interrupts property) by name.
+ "interrupt-names" examples are "hc_irq" and "pwr_irq"
+ - <supply-name>-supply: phandle to the regulator device tree node
+ "supply-name" examples are "vdd", "vdd-io".
+
+Optional Properties:
+ - cell-index - defines slot ID.
+ - qcom,bus-width - defines the bus I/O width that controller supports.
+ - qcom,nonremovable - specifies whether the card in slot is
+ hot pluggable or hard wired.
+ - qcom,bus-speed-mode - specifies supported bus speed modes by host.
+ - qcom,current-limit - specifies max. current the host can drive.
+
+In the following, <supply> can be vdd (flash core voltage) or vdd-io (I/O voltage).
+ - qcom,<supply>-always_on - specifies whether supply should be kept "on" always.
+ - qcom,<supply>-lpm_sup - specifies whether supply can be kept in low power mode (lpm).
+ - qcom,<supply>-voltage_level - specifies voltage levels for supply. Should be
+ specified in pairs (min, max), units uV.
+ - qcom,<supply>-current_level - specifies load levels for supply in lpm or
+ high power mode (hpm). Should be specified in pairs (lpm, hpm), units uA.
+
+ - gpios - specifies gpios assigned for sdhc slot.
+ - qcom,gpio-names - a list of strings that map in order to the list of gpios
+
+ - qcom,max-clk-rate - specifies the max. clock rate supported for a particular slot.
+
+Example:
+
+ qcom,sdhc@f9824900 {
+ cell-index = <1>; // SDC1 used as eMMC slot
+ compatible = "qcom,sdhci-msm";
+ reg = <0xf9824900 0x11C>, // SDHC register interface
+ <0xf9824000 0x800> // SD Core register interface
+
+ interrupts = <0 123 0>, // Core interrupt
+ <0 138 0>; // Pwr interrupt
+ qcom,sdcc-bus-width = <8>; // 8-bit wide
+ qcom,sdcc-nonremovable;
+ };
@@ -458,6 +458,19 @@ config MMC_SDRICOH_CS
config MMC_TMIO_CORE
tristate
+config MMC_SDHCI_MSM
+ tristate "Qualcomm SDHCI Controller Support"
+ depends on ARCH_MSM
+ depends on MMC_SDHCI_PLTFM
+ help
+ This selects the Secure Digital Host Controller Interface (SDHCI)
+ support present in MSM SOCs from Qualcomm. The controller
+ supports SD/MMC/SDIO devices.
+
+ If you have a controller with this interface, say Y or M here.
+
+ If unsure, say N.
+
config MMC_MSM
tristate "Qualcomm SDCC Controller Support"
depends on MMC && ARCH_MSM
@@ -56,6 +56,7 @@ obj-$(CONFIG_MMC_SDHCI_DOVE) += sdhci-dove.o
obj-$(CONFIG_MMC_SDHCI_TEGRA) += sdhci-tegra.o
obj-$(CONFIG_MMC_SDHCI_OF_ESDHC) += sdhci-of-esdhc.o
obj-$(CONFIG_MMC_SDHCI_OF_HLWD) += sdhci-of-hlwd.o
+obj-$(CONFIG_MMC_SDHCI_MSM) += sdhci-msm.o
ifeq ($(CONFIG_CB710_DEBUG),y)
CFLAGS-cb710-mmc += -DDEBUG
new file mode 100644
@@ -0,0 +1,961 @@
+/*
+ * drivers/mmc/host/sdhci-msm.c - Qualcomm MSM SDHCI Platform
+ * driver source file
+ *
+ * Copyright (c) 2013, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/mmc/host.h>
+#include <linux/mmc/card.h>
+#include <linux/mmc/sdio_func.h>
+#include <linux/gfp.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
+#include <linux/regulator/consumer.h>
+#include <linux/types.h>
+#include <linux/input.h>
+#include <linux/platform_device.h>
+
+#include "sdhci-pltfm.h"
+
+#define CORE_HC_MODE 0x78
+#define HC_MODE_EN 0x1
+
+#define CORE_POWER 0x0
+#define CORE_SW_RST (1 << 7)
+
+#define CORE_PWRCTL_STATUS 0xDC
+#define CORE_PWRCTL_MASK 0xE0
+#define CORE_PWRCTL_CLEAR 0xE4
+#define CORE_PWRCTL_CTL 0xE8
+
+#define CORE_PWRCTL_BUS_OFF 0x01
+#define CORE_PWRCTL_BUS_ON (1 << 1)
+#define CORE_PWRCTL_IO_LOW (1 << 2)
+#define CORE_PWRCTL_IO_HIGH (1 << 3)
+
+#define CORE_PWRCTL_BUS_SUCCESS 0x01
+#define CORE_PWRCTL_BUS_FAIL (1 << 1)
+#define CORE_PWRCTL_IO_SUCCESS (1 << 2)
+#define CORE_PWRCTL_IO_FAIL (1 << 3)
+
+#define INT_MASK 0xF
+
+/* This structure keeps information per regulator */
+struct sdhci_msm_reg_data {
+ /* voltage regulator handle */
+ struct regulator *reg;
+ /* regulator name */
+ const char *name;
+ /* voltage level to be set */
+ u32 low_vol_level;
+ u32 high_vol_level;
+ /* Load values for low power and high power mode */
+ u32 lpm_uA;
+ u32 hpm_uA;
+
+ /* is this regulator enabled? */
+ bool is_enabled;
+ /* is this regulator needs to be always on? */
+ bool always_on;
+ /* is low power mode setting required for this regulator? */
+ bool lpm_sup;
+};
+
+/*
+ * This structure keeps information for all the
+ * regulators required for a SDCC slot.
+ */
+struct sdhci_msm_slot_reg_data {
+ /* keeps VDD/VCC regulator info */
+ struct sdhci_msm_reg_data *vdd_data;
+ /* keeps VDD IO regulator info */
+ struct sdhci_msm_reg_data *vdd_io_data;
+};
+
+struct sdhci_msm_gpio {
+ u32 no;
+ const char *name;
+ bool is_always_on;
+ bool is_enabled;
+};
+
+struct sdhci_msm_gpio_data {
+ struct sdhci_msm_gpio *gpio;
+ u8 size;
+};
+
+struct sdhci_msm_pin_data {
+ /*
+ * = 1 if controller pins are using gpios
+ * = 0 if controller has dedicated MSM pads
+ */
+ u8 cfg_sts;
+ struct sdhci_msm_gpio_data *gpio_data;
+};
+
+struct sdhci_msm_pltfm_data {
+ /* Supported UHS-I Modes */
+ u32 caps;
+
+ /* More capabilities */
+ u32 caps2;
+
+ unsigned long mmc_bus_width;
+ u32 max_clk;
+ struct sdhci_msm_slot_reg_data *vreg_data;
+ bool nonremovable;
+ struct sdhci_msm_pin_data *pin_data;
+};
+
+struct sdhci_msm_host {
+ void __iomem *core_mem; /* MSM SDCC mapped address */
+ struct clk *clk; /* main SD/MMC bus clock */
+ struct clk *pclk; /* SDHC peripheral bus clock */
+ struct clk *bus_clk; /* SDHC bus voter clock */
+ struct sdhci_msm_pltfm_data *pdata;
+ struct mmc_host *mmc;
+ struct sdhci_pltfm_data sdhci_msm_pdata;
+};
+
+enum vdd_io_level {
+ /* set vdd_io_data->low_vol_level */
+ VDD_IO_LOW,
+ /* set vdd_io_data->high_vol_level */
+ VDD_IO_HIGH,
+ /*
+ * set whatever there in voltage_level (third argument) of
+ * sdhci_msm_set_vdd_io_vol() function.
+ */
+ VDD_IO_SET_LEVEL,
+};
+
+static int sdhci_msm_setup_gpio(struct sdhci_msm_pltfm_data *pdata, bool enable)
+{
+ struct sdhci_msm_gpio_data *curr;
+ int i, ret = 0;
+
+ curr = pdata->pin_data->gpio_data;
+ for (i = 0; i < curr->size; i++) {
+ if (!gpio_is_valid(curr->gpio[i].no)) {
+ ret = -EINVAL;
+ pr_err("%s: Invalid gpio = %d\n",
+ __func__, curr->gpio[i].no);
+ goto free_gpios;
+ }
+ if (enable) {
+ if (curr->gpio[i].is_always_on &&
+ curr->gpio[i].is_enabled)
+ continue;
+ ret = gpio_request(curr->gpio[i].no,
+ curr->gpio[i].name);
+ if (ret) {
+ pr_err("%s: gpio_request(%d, %s) failed %d\n",
+ __func__, curr->gpio[i].no,
+ curr->gpio[i].name, ret);
+ goto free_gpios;
+ }
+ curr->gpio[i].is_enabled = true;
+ } else {
+ if (curr->gpio[i].is_always_on)
+ continue;
+ gpio_free(curr->gpio[i].no);
+ curr->gpio[i].is_enabled = false;
+ }
+ }
+ goto out;
+
+free_gpios:
+ for (i--; i >= 0; i--) {
+ gpio_free(curr->gpio[i].no);
+ curr->gpio[i].is_enabled = false;
+ }
+out:
+ return ret;
+}
+
+int sdhci_msm_setup_pins(struct sdhci_msm_pltfm_data *pdata, bool enable)
+{
+ int ret = 0;
+
+ if (!pdata->pin_data ||
+ pdata->pin_data->cfg_sts == enable)
+ return 0;
+
+ ret = sdhci_msm_setup_gpio(pdata, enable);
+ if (!ret)
+ pdata->pin_data->cfg_sts = enable;
+
+ return ret;
+}
+
+#define MAX_PROP_SIZE 32
+static int sdhci_msm_dt_parse_vreg_info(struct device *dev,
+ struct sdhci_msm_reg_data **vreg_data, const char *vreg_name)
+{
+ int len, ret = 0;
+ const __be32 *prop;
+ char prop_name[MAX_PROP_SIZE];
+ struct sdhci_msm_reg_data *vreg;
+ struct device_node *np = dev->of_node;
+
+ snprintf(prop_name, MAX_PROP_SIZE, "%s-supply", vreg_name);
+ if (!of_parse_phandle(np, prop_name, 0)) {
+ ret = -EINVAL;
+ goto out;
+ }
+
+ vreg = devm_kzalloc(dev, sizeof(*vreg), GFP_KERNEL);
+ if (!vreg) {
+ dev_err(dev, "No memory for vreg: %s\n", vreg_name);
+ ret = -ENOMEM;
+ goto out;
+ }
+
+ vreg->name = vreg_name;
+
+ snprintf(prop_name, MAX_PROP_SIZE,
+ "qcom,%s-always-on", vreg_name);
+ if (of_get_property(np, prop_name, NULL))
+ vreg->always_on = true;
+
+ snprintf(prop_name, MAX_PROP_SIZE,
+ "qcom,%s-lpm-sup", vreg_name);
+ if (of_get_property(np, prop_name, NULL))
+ vreg->lpm_sup = true;
+
+ snprintf(prop_name, MAX_PROP_SIZE,
+ "qcom,%s-voltage-level", vreg_name);
+ prop = of_get_property(np, prop_name, &len);
+ if (!prop || (len != (2 * sizeof(__be32)))) {
+ dev_warn(dev, "%s %s property\n",
+ prop ? "invalid format" : "no", prop_name);
+ } else {
+ vreg->low_vol_level = be32_to_cpup(&prop[0]);
+ vreg->high_vol_level = be32_to_cpup(&prop[1]);
+ }
+
+ snprintf(prop_name, MAX_PROP_SIZE,
+ "qcom,%s-current-level", vreg_name);
+ prop = of_get_property(np, prop_name, &len);
+ if (!prop || (len != (2 * sizeof(__be32)))) {
+ dev_warn(dev, "%s %s property\n",
+ prop ? "invalid format" : "no", prop_name);
+ } else {
+ vreg->lpm_uA = be32_to_cpup(&prop[0]);
+ vreg->hpm_uA = be32_to_cpup(&prop[1]);
+ }
+
+ *vreg_data = vreg;
+ dev_dbg(dev, "%s: %s %s vol=[%d %d]uV, curr=[%d %d]uA\n",
+ vreg->name, vreg->always_on ? "always_on," : "",
+ vreg->lpm_sup ? "lpm_sup," : "", vreg->low_vol_level,
+ vreg->high_vol_level, vreg->lpm_uA, vreg->hpm_uA);
+
+out:
+ return ret;
+}
+
+static int sdhci_msm_dt_parse_gpio_info(struct device *dev,
+ struct sdhci_msm_pltfm_data *pdata)
+{
+ int ret = 0, cnt, i;
+ struct sdhci_msm_pin_data *pin_data;
+ struct device_node *np = dev->of_node;
+
+ pin_data = devm_kzalloc(dev, sizeof(*pin_data), GFP_KERNEL);
+ if (!pin_data) {
+ dev_err(dev, "No memory for pin_data\n");
+ ret = -ENOMEM;
+ goto out;
+ }
+
+ cnt = of_gpio_count(np);
+ if (cnt > 0) {
+ pin_data->gpio_data = devm_kzalloc(dev,
+ sizeof(struct sdhci_msm_gpio_data), GFP_KERNEL);
+ if (!pin_data->gpio_data) {
+ dev_err(dev, "No memory for gpio_data\n");
+ ret = -ENOMEM;
+ goto out;
+ }
+ pin_data->gpio_data->size = cnt;
+ pin_data->gpio_data->gpio = devm_kzalloc(dev, cnt *
+ sizeof(struct sdhci_msm_gpio), GFP_KERNEL);
+
+ if (!pin_data->gpio_data->gpio) {
+ dev_err(dev, "No memory for gpio\n");
+ ret = -ENOMEM;
+ goto out;
+ }
+
+ for (i = 0; i < cnt; i++) {
+ const char *name = NULL;
+ char result[32];
+ pin_data->gpio_data->gpio[i].no = of_get_gpio(np, i);
+ of_property_read_string_index(np,
+ "qcom,gpio-names", i, &name);
+
+ snprintf(result, 32, "%s-%s",
+ dev_name(dev), name ? name : "?");
+ pin_data->gpio_data->gpio[i].name = result;
+ dev_dbg(dev, "%s: gpio[%s] = %d\n", __func__,
+ pin_data->gpio_data->gpio[i].name,
+ pin_data->gpio_data->gpio[i].no);
+ pdata->pin_data = pin_data;
+ }
+ }
+
+out:
+ if (ret)
+ dev_err(dev, "%s failed with err %d\n", __func__, ret);
+ return ret;
+}
+
+/* Parse platform data */
+struct sdhci_msm_pltfm_data *sdhci_msm_populate_pdata(struct device *dev)
+{
+ struct sdhci_msm_pltfm_data *pdata = NULL;
+ struct device_node *np = dev->of_node;
+ u32 bus_width = 0;
+ int len, i;
+
+ pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
+ if (!pdata) {
+ dev_err(dev, "failed to allocate memory for platform data\n");
+ goto out;
+ }
+
+ of_property_read_u32(np, "qcom,bus-width", &bus_width);
+ if (bus_width == 8)
+ pdata->mmc_bus_width = MMC_CAP_8_BIT_DATA;
+ else if (bus_width == 4)
+ pdata->mmc_bus_width = MMC_CAP_4_BIT_DATA;
+ else {
+ dev_notice(dev, "invalid bus-width, default to 1-bit mode\n");
+ pdata->mmc_bus_width = 0;
+ }
+
+ pdata->vreg_data = devm_kzalloc(dev, sizeof(struct
+ sdhci_msm_slot_reg_data),
+ GFP_KERNEL);
+ if (!pdata->vreg_data) {
+ dev_err(dev, "failed to allocate memory for vreg data\n");
+ goto out;
+ }
+
+ if (sdhci_msm_dt_parse_vreg_info(dev, &pdata->vreg_data->vdd_data,
+ "vdd")) {
+ dev_err(dev, "failed parsing vdd data\n");
+ goto out;
+ }
+ if (sdhci_msm_dt_parse_vreg_info(dev,
+ &pdata->vreg_data->vdd_io_data,
+ "vdd-io")) {
+ dev_err(dev, "failed parsing vdd-io data\n");
+ goto out;
+ }
+
+ if (sdhci_msm_dt_parse_gpio_info(dev, pdata)) {
+ dev_err(dev, "failed parsing gpio data\n");
+ goto out;
+ }
+
+ of_property_read_u32(np, "qcom,max-clk-rate", &pdata->max_clk);
+
+ len = of_property_count_strings(np, "qcom,bus-speed-mode");
+
+ for (i = 0; i < len; i++) {
+ const char *name = NULL;
+
+ of_property_read_string_index(np,
+ "qcom,bus-speed-mode", i, &name);
+ if (!name)
+ continue;
+
+ if (!strncmp(name, "HS200_1p8v", sizeof("HS200_1p8v")))
+ pdata->caps2 |= MMC_CAP2_HS200_1_8V_SDR;
+ else if (!strncmp(name, "HS200_1p2v", sizeof("HS200_1p2v")))
+ pdata->caps2 |= MMC_CAP2_HS200_1_2V_SDR;
+ else if (!strncmp(name, "DDR_1p8v", sizeof("DDR_1p8v")))
+ pdata->caps |= MMC_CAP_1_8V_DDR
+ | MMC_CAP_UHS_DDR50;
+ else if (!strncmp(name, "DDR_1p2v", sizeof("DDR_1p2v")))
+ pdata->caps |= MMC_CAP_1_2V_DDR
+ | MMC_CAP_UHS_DDR50;
+ }
+
+ if (of_get_property(np, "qcom,nonremovable", NULL))
+ pdata->nonremovable = true;
+
+ return pdata;
+out:
+ return NULL;
+}
+
+/* Regulator utility functions */
+static inline int sdhci_msm_vreg_init_reg(struct device *dev,
+ struct sdhci_msm_reg_data *vreg)
+{
+ int ret = 0;
+
+ /* check if regulator is already initialized? */
+ if (vreg->reg)
+ goto out;
+
+ /* Get the regulator handle */
+ vreg->reg = devm_regulator_get(dev, vreg->name);
+ if (IS_ERR(vreg->reg)) {
+ ret = PTR_ERR(vreg->reg);
+ pr_err("%s: devm_regulator_get(%s) failed. ret=%d\n",
+ __func__, vreg->name, ret);
+ goto out;
+ }
+
+ /* sanity check */
+ if (!vreg->high_vol_level || !vreg->hpm_uA) {
+ pr_err("%s: %s invalid constraints specified\n",
+ __func__, vreg->name);
+ ret = -EINVAL;
+ }
+
+out:
+ return ret;
+}
+
+static inline void sdhci_msm_vreg_deinit_reg(struct sdhci_msm_reg_data *vreg)
+{
+ if (vreg->reg)
+ devm_regulator_put(vreg->reg);
+}
+
+static inline int sdhci_msm_vreg_set_optimum_mode(struct sdhci_msm_reg_data
+ *vreg, int uA_load)
+{
+ int ret = 0;
+
+ /* regulators that do not support regulator_set_voltage also
+ do not support regulator_set_optimum_mode */
+ ret = regulator_set_optimum_mode(vreg->reg, uA_load);
+ if (ret < 0)
+ pr_err("%s: regulator_set_optimum_mode(reg=%s,uA_load=%d) failed. ret=%d\n",
+ __func__, vreg->name, uA_load, ret);
+ else
+ /* regulator_set_optimum_mode() can return non zero
+ * value even for success case.
+ */
+ ret = 0;
+ return ret;
+}
+
+static inline int sdhci_msm_vreg_set_voltage(struct sdhci_msm_reg_data *vreg,
+ int min_uV, int max_uV)
+{
+ int ret = 0;
+
+ ret = regulator_set_voltage(vreg->reg, min_uV, max_uV);
+ if (ret) {
+ pr_err("%s:regulator_set_voltage(%s)failed. min_uV=%d,max_uV=%d,ret=%d\n",
+ __func__, vreg->name, min_uV, max_uV, ret);
+ }
+
+ return ret;
+}
+
+static inline int sdhci_msm_vreg_get_voltage(struct sdhci_msm_reg_data *vreg)
+{
+ int ret = 0;
+
+ ret = regulator_get_voltage(vreg->reg);
+ if (ret < 0)
+ pr_err("%s: regulator_get_voltage(%s) failed. ret=%d\n",
+ __func__, vreg->name, ret);
+
+ return ret;
+}
+
+static int sdhci_msm_vreg_enable(struct sdhci_msm_reg_data *vreg)
+{
+ int ret = 0;
+
+ /* Put regulator in HPM (high power mode) */
+ ret = sdhci_msm_vreg_set_optimum_mode(vreg, vreg->hpm_uA);
+ if (ret < 0)
+ goto out;
+
+ if (!vreg->is_enabled) {
+ /* Set voltage level */
+ ret = sdhci_msm_vreg_set_voltage(vreg, vreg->high_vol_level,
+ vreg->high_vol_level);
+ if (ret)
+ goto out;
+ }
+ ret = regulator_enable(vreg->reg);
+ if (ret) {
+ pr_err("%s: regulator_enable(%s) failed. ret=%d\n",
+ __func__, vreg->name, ret);
+ goto out;
+ }
+ vreg->is_enabled = true;
+out:
+ return ret;
+}
+
+static int sdhci_msm_vreg_disable(struct sdhci_msm_reg_data *vreg)
+{
+ int ret = 0;
+
+ /* Never disable regulator marked as always_on */
+ if (vreg->is_enabled && !vreg->always_on) {
+ ret = regulator_disable(vreg->reg);
+ if (ret) {
+ pr_err("%s: regulator_disable(%s) failed. ret=%d\n",
+ __func__, vreg->name, ret);
+ goto out;
+ }
+ vreg->is_enabled = false;
+
+ ret = sdhci_msm_vreg_set_optimum_mode(vreg, 0);
+ if (ret < 0)
+ goto out;
+
+ /* Set min. voltage level to 0 */
+ ret = sdhci_msm_vreg_set_voltage(vreg, 0, vreg->high_vol_level);
+ if (ret)
+ goto out;
+ } else if (vreg->is_enabled && vreg->always_on) {
+ if (vreg->lpm_sup) {
+ /* Put always_on regulator in LPM (low power mode) */
+ ret = sdhci_msm_vreg_set_optimum_mode(vreg,
+ vreg->lpm_uA);
+ if (ret < 0)
+ goto out;
+ }
+ }
+out:
+ return ret;
+}
+
+int sdhci_msm_setup_vreg(struct sdhci_msm_pltfm_data *pdata,
+ bool enable, bool is_init)
+{
+ int ret = 0, i;
+ struct sdhci_msm_slot_reg_data *curr_slot;
+ struct sdhci_msm_reg_data *vreg_table[2];
+
+ curr_slot = pdata->vreg_data;
+ if (!curr_slot) {
+ pr_debug("%s: vreg info unavailable, assuming the slot is powered by always on domain\n",
+ __func__);
+ goto out;
+ }
+
+ vreg_table[0] = curr_slot->vdd_data;
+ vreg_table[1] = curr_slot->vdd_io_data;
+
+ for (i = 0; i < ARRAY_SIZE(vreg_table); i++) {
+ if (vreg_table[i]) {
+ if (enable)
+ ret = sdhci_msm_vreg_enable(vreg_table[i]);
+ else
+ ret = sdhci_msm_vreg_disable(vreg_table[i]);
+ if (ret)
+ goto out;
+ }
+ }
+out:
+ return ret;
+}
+
+/*
+ * Reset vreg by ensuring it is off during probe. A call
+ * to enable vreg is needed to balance disable vreg
+ */
+static int sdhci_msm_vreg_reset(struct sdhci_msm_pltfm_data *pdata)
+{
+ int ret;
+
+ ret = sdhci_msm_setup_vreg(pdata, 1, true);
+ if (ret)
+ return ret;
+ ret = sdhci_msm_setup_vreg(pdata, 0, true);
+ return ret;
+}
+
+/* This init function should be called only once for each SDHC slot */
+int sdhci_msm_vreg_init(struct device *dev,
+ struct sdhci_msm_pltfm_data *pdata,
+ bool is_init)
+{
+ int ret = 0;
+ struct sdhci_msm_slot_reg_data *curr_slot;
+ struct sdhci_msm_reg_data *curr_vdd_reg, *curr_vdd_io_reg;
+
+ curr_slot = pdata->vreg_data;
+ if (!curr_slot)
+ goto out;
+
+ curr_vdd_reg = curr_slot->vdd_data;
+ curr_vdd_io_reg = curr_slot->vdd_io_data;
+
+ if (!is_init)
+ /* Deregister all regulators from regulator framework */
+ goto vdd_io_reg_deinit;
+
+ /*
+ * Get the regulator handle from voltage regulator framework
+ * and then try to set the voltage level for the regulator
+ */
+ if (curr_vdd_reg) {
+ ret = sdhci_msm_vreg_init_reg(dev, curr_vdd_reg);
+ if (ret)
+ goto out;
+ }
+ if (curr_vdd_io_reg) {
+ ret = sdhci_msm_vreg_init_reg(dev, curr_vdd_io_reg);
+ if (ret)
+ goto vdd_reg_deinit;
+ }
+ ret = sdhci_msm_vreg_reset(pdata);
+ if (ret)
+ dev_err(dev, "vreg reset failed (%d)\n", ret);
+ goto out;
+
+vdd_io_reg_deinit:
+ if (curr_vdd_io_reg)
+ sdhci_msm_vreg_deinit_reg(curr_vdd_io_reg);
+vdd_reg_deinit:
+ if (curr_vdd_reg)
+ sdhci_msm_vreg_deinit_reg(curr_vdd_reg);
+out:
+ return ret;
+}
+
+
+int sdhci_msm_set_vdd_io_vol(struct sdhci_msm_pltfm_data *pdata,
+ enum vdd_io_level level,
+ unsigned int voltage_level)
+{
+ int ret = 0;
+ int set_level;
+
+ if (pdata->vreg_data) {
+ struct sdhci_msm_reg_data *vdd_io_reg =
+ pdata->vreg_data->vdd_io_data;
+
+ if (vdd_io_reg && vdd_io_reg->is_enabled) {
+ switch (level) {
+ case VDD_IO_LOW:
+ set_level = vdd_io_reg->low_vol_level;
+ break;
+ case VDD_IO_HIGH:
+ set_level = vdd_io_reg->high_vol_level;
+ break;
+ case VDD_IO_SET_LEVEL:
+ set_level = voltage_level;
+ break;
+ default:
+ pr_err("%s: invalid argument level = %d",
+ __func__, level);
+ ret = -EINVAL;
+ goto out;
+ }
+ ret = sdhci_msm_vreg_set_voltage(vdd_io_reg,
+ set_level, set_level);
+ }
+ }
+
+out:
+ return ret;
+}
+
+static irqreturn_t sdhci_msm_pwr_irq(int irq, void *data)
+{
+ struct sdhci_msm_host *msm_host = (struct sdhci_msm_host *)data;
+ u8 irq_status = 0;
+ u8 irq_ack = 0;
+ int ret = 0;
+
+ irq_status = readb_relaxed(msm_host->core_mem + CORE_PWRCTL_STATUS);
+ pr_debug("%s: Received IRQ(%d), status=0x%x\n",
+ mmc_hostname(msm_host->mmc), irq, irq_status);
+
+ /* Clear the interrupt */
+ writeb_relaxed(irq_status, (msm_host->core_mem + CORE_PWRCTL_CLEAR));
+ mb();
+
+ /* Handle BUS ON/OFF */
+ if (irq_status & (CORE_PWRCTL_BUS_ON | CORE_PWRCTL_BUS_OFF)) {
+ bool flag = (irq_status & CORE_PWRCTL_BUS_ON) ? 1 : 0;
+ ret = sdhci_msm_setup_vreg(msm_host->pdata, flag, false);
+ if (!ret)
+ sdhci_msm_setup_pins(msm_host->pdata, flag);
+ if (ret)
+ irq_ack |= CORE_PWRCTL_BUS_FAIL;
+ else
+ irq_ack |= CORE_PWRCTL_BUS_SUCCESS;
+ goto out;
+ }
+ /* Handle IO LOW/HIGH */
+ if (irq_status & (CORE_PWRCTL_IO_LOW | CORE_PWRCTL_IO_HIGH)) {
+ /* Switch voltage */
+ int io_status = (irq_status & CORE_PWRCTL_IO_LOW) ?
+ VDD_IO_LOW : VDD_IO_HIGH;
+ ret = sdhci_msm_set_vdd_io_vol(msm_host->pdata, io_status, 0);
+ if (ret)
+ irq_ack |= CORE_PWRCTL_IO_FAIL;
+ else
+ irq_ack |= CORE_PWRCTL_IO_SUCCESS;
+ goto out;
+ }
+
+out:
+ /* ACK status to the core */
+ writeb_relaxed(irq_ack, (msm_host->core_mem + CORE_PWRCTL_CTL));
+ mb();
+
+ pr_debug("%s: Handled IRQ(%d), ret=%d, ack=0x%x\n",
+ mmc_hostname(msm_host->mmc), irq, ret, irq_ack);
+ return IRQ_HANDLED;
+}
+
+/* This function returns the max. current supported by VDD rail in mA */
+static unsigned int sdhci_msm_get_vreg_vdd_max_current(struct sdhci_msm_host
+ *host)
+{
+ struct sdhci_msm_slot_reg_data *curr_slot = host->pdata->vreg_data;
+ if (!curr_slot)
+ return 0;
+ if (curr_slot->vdd_data)
+ return curr_slot->vdd_data->hpm_uA / 1000;
+ else
+ return 0;
+}
+
+static int __devinit sdhci_msm_probe(struct platform_device *pdev)
+{
+ struct sdhci_host *host;
+ struct sdhci_pltfm_host *pltfm_host;
+ struct sdhci_msm_host *msm_host;
+ struct resource *core_memres = NULL;
+ int ret = 0, pwr_irq = 0, dead = 0;
+
+ pr_debug("%s: Enter %s\n", dev_name(&pdev->dev), __func__);
+ msm_host = devm_kzalloc(&pdev->dev, sizeof(struct sdhci_msm_host),
+ GFP_KERNEL);
+ if (!msm_host) {
+ ret = -ENOMEM;
+ goto out;
+ }
+
+ host = sdhci_pltfm_init(pdev, &msm_host->sdhci_msm_pdata);
+ if (IS_ERR(host)) {
+ ret = PTR_ERR(host);
+ goto out;
+ }
+
+ pltfm_host = sdhci_priv(host);
+ pltfm_host->priv = msm_host;
+ msm_host->mmc = host->mmc;
+
+ /* Extract platform data */
+ if (pdev->dev.of_node) {
+ msm_host->pdata = sdhci_msm_populate_pdata(&pdev->dev);
+ if (!msm_host->pdata) {
+ dev_err(&pdev->dev, "DT parsing error\n");
+ goto pltfm_free;
+ }
+ } else {
+ dev_err(&pdev->dev, "No device tree node\n");
+ goto pltfm_free;
+ }
+
+ /* Setup Clocks */
+
+ /* Setup SDCC bus voter clock. */
+ msm_host->bus_clk = devm_clk_get(&pdev->dev, "bus_clk");
+ if (!IS_ERR_OR_NULL(msm_host->bus_clk)) {
+ /* Vote for max. clk rate for max. performance */
+ ret = clk_set_rate(msm_host->bus_clk, INT_MAX);
+ if (ret)
+ goto pltfm_free;
+ ret = clk_prepare_enable(msm_host->bus_clk);
+ if (ret)
+ goto pltfm_free;
+ }
+
+ /* Setup main peripheral bus clock */
+ msm_host->pclk = devm_clk_get(&pdev->dev, "iface_clk");
+ if (!IS_ERR(msm_host->pclk)) {
+ ret = clk_prepare_enable(msm_host->pclk);
+ if (ret)
+ goto bus_clk_disable;
+ }
+
+ /* Setup SDC MMC clock */
+ msm_host->clk = devm_clk_get(&pdev->dev, "core_clk");
+ if (IS_ERR(msm_host->clk)) {
+ ret = PTR_ERR(msm_host->clk);
+ goto pclk_disable;
+ }
+
+ ret = clk_prepare_enable(msm_host->clk);
+ if (ret)
+ goto pclk_disable;
+
+ /* Setup regulators */
+ ret = sdhci_msm_vreg_init(&pdev->dev, msm_host->pdata, true);
+ if (ret) {
+ dev_err(&pdev->dev, "Regulator setup failed (%d)\n", ret);
+ goto clk_disable;
+ }
+
+ /* Reset the core and Enable SDHC mode */
+ core_memres = platform_get_resource_byname(pdev,
+ IORESOURCE_MEM, "core_mem");
+ msm_host->core_mem = devm_ioremap(&pdev->dev, core_memres->start,
+ resource_size(core_memres));
+
+ if (!msm_host->core_mem) {
+ dev_err(&pdev->dev, "Failed to remap registers\n");
+ ret = -ENOMEM;
+ goto vreg_deinit;
+ }
+
+ /* Set SW_RST bit in POWER register (Offset 0x0) */
+ writel_relaxed(CORE_SW_RST, msm_host->core_mem + CORE_POWER);
+ /* Set HC_MODE_EN bit in HC_MODE register */
+ writel_relaxed(HC_MODE_EN, (msm_host->core_mem + CORE_HC_MODE));
+
+ /* Deviations from SDHC spec v3.0 */
+ /* Card detection is handled using separate GPIO's */
+ host->quirks |= SDHCI_QUIRK_BROKEN_CARD_DETECTION;
+
+ /* Bus power control is handled by interacting with PMIC */
+ /* Setup PWRCTL irq */
+ pwr_irq = platform_get_irq_byname(pdev, "pwr_irq");
+ if (pwr_irq < 0) {
+ dev_err(&pdev->dev, "Failed to get pwr_irq by name (%d)\n",
+ pwr_irq);
+ goto vreg_deinit;
+ }
+ ret = devm_request_threaded_irq(&pdev->dev, pwr_irq, NULL,
+ sdhci_msm_pwr_irq, IRQF_ONESHOT,
+ dev_name(&pdev->dev), msm_host);
+ if (ret) {
+ dev_err(&pdev->dev, "Request threaded irq(%d) failed (%d)\n",
+ pwr_irq, ret);
+ goto vreg_deinit;
+ }
+
+ /* Enable pwr irq interrupts */
+ writel_relaxed(INT_MASK, (msm_host->core_mem + CORE_PWRCTL_MASK));
+
+ /* Set host capabilities */
+ msm_host->mmc->caps |= msm_host->pdata->mmc_bus_width;
+ msm_host->mmc->caps |= msm_host->pdata->caps;
+ msm_host->mmc->caps2 |= msm_host->pdata->caps2;
+
+ if (msm_host->pdata->nonremovable)
+ msm_host->mmc->caps |= MMC_CAP_NONREMOVABLE;
+
+ ret = sdhci_add_host(host);
+ if (ret) {
+ dev_err(&pdev->dev, "Add host failed (%d)\n", ret);
+ goto vreg_deinit;
+ }
+
+ /* Set core clk rate, optionally override from dts */
+ if (msm_host->pdata->max_clk)
+ host->max_clk = msm_host->pdata->max_clk;
+ ret = clk_set_rate(msm_host->clk, host->max_clk);
+ if (ret) {
+ dev_err(&pdev->dev, "MClk rate set failed (%d)\n", ret);
+ goto remove_host;
+ }
+
+ host->mmc->max_current_180 =
+ sdhci_msm_get_vreg_vdd_max_current(msm_host);
+ host->mmc->max_current_300 =
+ sdhci_msm_get_vreg_vdd_max_current(msm_host);
+ host->mmc->max_current_330 =
+ sdhci_msm_get_vreg_vdd_max_current(msm_host);
+
+ /* Successful initialization */
+ goto out;
+
+remove_host:
+ dead = (readl_relaxed(host->ioaddr + SDHCI_INT_STATUS) == 0xffffffff);
+ sdhci_remove_host(host, dead);
+vreg_deinit:
+ sdhci_msm_vreg_init(&pdev->dev, msm_host->pdata, false);
+clk_disable:
+ if (!IS_ERR(msm_host->clk))
+ clk_disable_unprepare(msm_host->clk);
+pclk_disable:
+ if (!IS_ERR(msm_host->pclk))
+ clk_disable_unprepare(msm_host->pclk);
+bus_clk_disable:
+ if (!IS_ERR_OR_NULL(msm_host->bus_clk))
+ clk_disable_unprepare(msm_host->bus_clk);
+pltfm_free:
+ sdhci_pltfm_free(pdev);
+out:
+ pr_debug("%s: Exit %s\n", dev_name(&pdev->dev), __func__);
+ return ret;
+}
+
+static int __devexit sdhci_msm_remove(struct platform_device *pdev)
+{
+ struct sdhci_host *host = platform_get_drvdata(pdev);
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_host *msm_host = pltfm_host->priv;
+ struct sdhci_msm_pltfm_data *pdata = msm_host->pdata;
+ int dead = (readl_relaxed(host->ioaddr + SDHCI_INT_STATUS) ==
+ 0xffffffff);
+
+ pr_debug("%s: %s\n", dev_name(&pdev->dev), __func__);
+ sdhci_remove_host(host, dead);
+ sdhci_pltfm_free(pdev);
+ sdhci_msm_vreg_init(&pdev->dev, msm_host->pdata, false);
+ if (!IS_ERR(msm_host->clk))
+ clk_disable_unprepare(msm_host->clk);
+ if (!IS_ERR(msm_host->pclk))
+ clk_disable_unprepare(msm_host->pclk);
+ if (!IS_ERR_OR_NULL(msm_host->bus_clk))
+ clk_disable_unprepare(msm_host->bus_clk);
+ if (pdata->pin_data)
+ sdhci_msm_setup_gpio(pdata, false);
+ return 0;
+}
+
+static const struct of_device_id sdhci_msm_dt_match[] = {
+ {.compatible = "qcom,sdhci-msm"},
+};
+MODULE_DEVICE_TABLE(of, sdhci_msm_dt_match);
+
+static struct platform_driver sdhci_msm_driver = {
+ .probe = sdhci_msm_probe,
+ .remove = __devexit_p(sdhci_msm_remove),
+ .driver = {
+ .name = "sdhci_msm",
+ .owner = THIS_MODULE,
+ .of_match_table = sdhci_msm_dt_match,
+ },
+};
+
+module_platform_driver(sdhci_msm_driver);
+
+MODULE_DESCRIPTION("Qualcomm Secure Digital Host Controller Interface driver");
+MODULE_LICENSE("GPLv2");