| Message ID | 1378299257-2980-4-git-send-email-b29396@freescale.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On Wed, Sep 04, 2013 at 08:54:12PM +0800, Dong Aisheng wrote: > The signal voltage switch follow requires to shutdown and output s/follow/flow > clock in a specific sequence according to standard host controller > v3.0 spec. In that timing, the card must really receive clock or not. > > However, for i.MX6Q, the uSDHC will not output clock even the clock > is enabled until there is command or data in transfer on the bus, > which will then cause singal voltage switch always to fail. > > For i.MX6Q, we clear ESDHC_VENDOR_SPEC_FRC_SDCLK_ON bit to let > controller to gate off clock automatically and set that bit > to force clock output if clock is on. > > This is required by SD3.0 support. > > Signed-off-by: Dong Aisheng <b29396@freescale.com> > --- > drivers/mmc/host/sdhci-esdhc-imx.c | 3 --- > drivers/mmc/host/sdhci-esdhc.h | 29 ++++++++++++++++++++++++++--- > 2 files changed, 26 insertions(+), 6 deletions(-) > > diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c > index 1dd5ba8..3118a82 100644 > --- a/drivers/mmc/host/sdhci-esdhc-imx.c > +++ b/drivers/mmc/host/sdhci-esdhc-imx.c > @@ -31,9 +31,6 @@ > #include "sdhci-esdhc.h" > > #define ESDHC_CTRL_D3CD 0x08 > -/* VENDOR SPEC register */ > -#define ESDHC_VENDOR_SPEC 0xc0 > -#define ESDHC_VENDOR_SPEC_SDIO_QUIRK (1 << 1) > #define ESDHC_WTMK_LVL 0x44 > #define ESDHC_MIX_CTRL 0x48 > #define ESDHC_MIX_CTRL_AC23EN (1 << 7) > diff --git a/drivers/mmc/host/sdhci-esdhc.h b/drivers/mmc/host/sdhci-esdhc.h > index a2a0642..86fcd5b 100644 > --- a/drivers/mmc/host/sdhci-esdhc.h > +++ b/drivers/mmc/host/sdhci-esdhc.h > @@ -14,6 +14,8 @@ > #ifndef _DRIVERS_MMC_SDHCI_ESDHC_H > #define _DRIVERS_MMC_SDHCI_ESDHC_H > > +#include <linux/of.h> > + > /* > * Ops and quirks for the Freescale eSDHC controller. > */ > @@ -33,6 +35,12 @@ > #define ESDHC_CLOCK_HCKEN 0x00000002 > #define ESDHC_CLOCK_IPGEN 0x00000001 > > +/* VENDOR SPEC register */ > +#define ESDHC_VENDOR_SPEC 0xc0 > +#define ESDHC_VENDOR_SPEC_SDIO_QUIRK (1 << 1) > +#define ESDHC_VENDOR_SPEC_VSELECT (1 << 1) It would be better to introduce the macro only when it's actually being used. > +#define ESDHC_VENDOR_SPEC_FRC_SDCLK_ON (1 << 8) > + > /* pltfm-specific */ > #define ESDHC_HOST_CONTROL_LE 0x20 > > @@ -52,12 +60,20 @@ > static inline void esdhc_set_clock(struct sdhci_host *host, unsigned int clock, > unsigned int host_clock) > { > + struct device *dev; > int pre_div = 2; > int div = 1; > - u32 temp; > - > - if (clock == 0) > + u32 temp, val; > + > + dev = mmc_dev(host->mmc); > + if (clock == 0) { > + if (of_device_is_compatible(dev->of_node, "fsl,imx6q-usdhc")) { > + val = readl(host->ioaddr + ESDHC_VENDOR_SPEC); > + writel(val & ~ESDHC_VENDOR_SPEC_FRC_SDCLK_ON, > + host->ioaddr + ESDHC_VENDOR_SPEC); > + } To me, maintaining this esdhc_set_clock() for both imx and powerpc makes no sense now. I think it might be the time to have different versions of the function for imx and powerpc, just in esdhc_pltfm_set_clock() and esdhc_of_set_clock() respectively. Shawn > goto out; > + } > > temp = sdhci_readl(host, ESDHC_SYSTEM_CONTROL); > temp &= ~(ESDHC_CLOCK_IPGEN | ESDHC_CLOCK_HCKEN | ESDHC_CLOCK_PEREN > @@ -81,6 +97,13 @@ static inline void esdhc_set_clock(struct sdhci_host *host, unsigned int clock, > | (div << ESDHC_DIVIDER_SHIFT) > | (pre_div << ESDHC_PREDIV_SHIFT)); > sdhci_writel(host, temp, ESDHC_SYSTEM_CONTROL); > + > + if (of_device_is_compatible(dev->of_node, "fsl,imx6q-usdhc")) { > + val = readl(host->ioaddr + ESDHC_VENDOR_SPEC); > + writel(val | ESDHC_VENDOR_SPEC_FRC_SDCLK_ON, > + host->ioaddr + ESDHC_VENDOR_SPEC); > + } > + > mdelay(1); > out: > host->clock = clock; > -- > 1.7.1 > > -- To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Thu, Sep 5, 2013 at 12:32 PM, Shawn Guo <shawn.guo@linaro.org> wrote: > > On Wed, Sep 04, 2013 at 08:54:12PM +0800, Dong Aisheng wrote: > > The signal voltage switch follow requires to shutdown and output > > s/follow/flow > > > clock in a specific sequence according to standard host controller > > v3.0 spec. In that timing, the card must really receive clock or not. > > > > However, for i.MX6Q, the uSDHC will not output clock even the clock > > is enabled until there is command or data in transfer on the bus, > > which will then cause singal voltage switch always to fail. > > > > For i.MX6Q, we clear ESDHC_VENDOR_SPEC_FRC_SDCLK_ON bit to let > > controller to gate off clock automatically and set that bit > > to force clock output if clock is on. > > > > This is required by SD3.0 support. > > > > Signed-off-by: Dong Aisheng <b29396@freescale.com> > > --- > > drivers/mmc/host/sdhci-esdhc-imx.c | 3 --- > > drivers/mmc/host/sdhci-esdhc.h | 29 ++++++++++++++++++++++++++--- > > 2 files changed, 26 insertions(+), 6 deletions(-) > > > > diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c > > index 1dd5ba8..3118a82 100644 > > --- a/drivers/mmc/host/sdhci-esdhc-imx.c > > +++ b/drivers/mmc/host/sdhci-esdhc-imx.c > > @@ -31,9 +31,6 @@ > > #include "sdhci-esdhc.h" > > > > #define ESDHC_CTRL_D3CD 0x08 > > -/* VENDOR SPEC register */ > > -#define ESDHC_VENDOR_SPEC 0xc0 > > -#define ESDHC_VENDOR_SPEC_SDIO_QUIRK (1 << 1) > > #define ESDHC_WTMK_LVL 0x44 > > #define ESDHC_MIX_CTRL 0x48 > > #define ESDHC_MIX_CTRL_AC23EN (1 << 7) > > diff --git a/drivers/mmc/host/sdhci-esdhc.h b/drivers/mmc/host/sdhci-esdhc.h > > index a2a0642..86fcd5b 100644 > > --- a/drivers/mmc/host/sdhci-esdhc.h > > +++ b/drivers/mmc/host/sdhci-esdhc.h > > @@ -14,6 +14,8 @@ > > #ifndef _DRIVERS_MMC_SDHCI_ESDHC_H > > #define _DRIVERS_MMC_SDHCI_ESDHC_H > > > > +#include <linux/of.h> > > + > > /* > > * Ops and quirks for the Freescale eSDHC controller. > > */ > > @@ -33,6 +35,12 @@ > > #define ESDHC_CLOCK_HCKEN 0x00000002 > > #define ESDHC_CLOCK_IPGEN 0x00000001 > > > > +/* VENDOR SPEC register */ > > +#define ESDHC_VENDOR_SPEC 0xc0 > > +#define ESDHC_VENDOR_SPEC_SDIO_QUIRK (1 << 1) > > +#define ESDHC_VENDOR_SPEC_VSELECT (1 << 1) > > It would be better to introduce the macro only when it's actually being > used. > Correct. > > +#define ESDHC_VENDOR_SPEC_FRC_SDCLK_ON (1 << 8) > > + > > /* pltfm-specific */ > > #define ESDHC_HOST_CONTROL_LE 0x20 > > > > @@ -52,12 +60,20 @@ > > static inline void esdhc_set_clock(struct sdhci_host *host, unsigned int clock, > > unsigned int host_clock) > > { > > + struct device *dev; > > int pre_div = 2; > > int div = 1; > > - u32 temp; > > - > > - if (clock == 0) > > + u32 temp, val; > > + > > + dev = mmc_dev(host->mmc); > > + if (clock == 0) { > > + if (of_device_is_compatible(dev->of_node, "fsl,imx6q-usdhc")) { > > + val = readl(host->ioaddr + ESDHC_VENDOR_SPEC); > > + writel(val & ~ESDHC_VENDOR_SPEC_FRC_SDCLK_ON, > > + host->ioaddr + ESDHC_VENDOR_SPEC); > > + } > > To me, maintaining this esdhc_set_clock() for both imx and powerpc makes > no sense now. I think it might be the time to have different versions > of the function for imx and powerpc, just in esdhc_pltfm_set_clock() and > esdhc_of_set_clock() respectively. I agree with you. Since later i will need add a few more imx6q specific things in this common headfile which seems not good. So it would be better to end this dependency ASAP. I could move that code into esdhc_pltfm_set_clock in next version if no objections from others people. Regards Dong Aisheng > > Shawn > > > goto out; > > + } > > > > temp = sdhci_readl(host, ESDHC_SYSTEM_CONTROL); > > temp &= ~(ESDHC_CLOCK_IPGEN | ESDHC_CLOCK_HCKEN | ESDHC_CLOCK_PEREN > > @@ -81,6 +97,13 @@ static inline void esdhc_set_clock(struct sdhci_host *host, unsigned int clock, > > | (div << ESDHC_DIVIDER_SHIFT) > > | (pre_div << ESDHC_PREDIV_SHIFT)); > > sdhci_writel(host, temp, ESDHC_SYSTEM_CONTROL); > > + > > + if (of_device_is_compatible(dev->of_node, "fsl,imx6q-usdhc")) { > > + val = readl(host->ioaddr + ESDHC_VENDOR_SPEC); > > + writel(val | ESDHC_VENDOR_SPEC_FRC_SDCLK_ON, > > + host->ioaddr + ESDHC_VENDOR_SPEC); > > + } > > + > > mdelay(1); > > out: > > host->clock = clock; > > -- > > 1.7.1 > > > > > > > _______________________________________________ > linux-arm-kernel mailing list > linux-arm-kernel@lists.infradead.org > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel -- To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c index 1dd5ba8..3118a82 100644 --- a/drivers/mmc/host/sdhci-esdhc-imx.c +++ b/drivers/mmc/host/sdhci-esdhc-imx.c @@ -31,9 +31,6 @@ #include "sdhci-esdhc.h" #define ESDHC_CTRL_D3CD 0x08 -/* VENDOR SPEC register */ -#define ESDHC_VENDOR_SPEC 0xc0 -#define ESDHC_VENDOR_SPEC_SDIO_QUIRK (1 << 1) #define ESDHC_WTMK_LVL 0x44 #define ESDHC_MIX_CTRL 0x48 #define ESDHC_MIX_CTRL_AC23EN (1 << 7) diff --git a/drivers/mmc/host/sdhci-esdhc.h b/drivers/mmc/host/sdhci-esdhc.h index a2a0642..86fcd5b 100644 --- a/drivers/mmc/host/sdhci-esdhc.h +++ b/drivers/mmc/host/sdhci-esdhc.h @@ -14,6 +14,8 @@ #ifndef _DRIVERS_MMC_SDHCI_ESDHC_H #define _DRIVERS_MMC_SDHCI_ESDHC_H +#include <linux/of.h> + /* * Ops and quirks for the Freescale eSDHC controller. */ @@ -33,6 +35,12 @@ #define ESDHC_CLOCK_HCKEN 0x00000002 #define ESDHC_CLOCK_IPGEN 0x00000001 +/* VENDOR SPEC register */ +#define ESDHC_VENDOR_SPEC 0xc0 +#define ESDHC_VENDOR_SPEC_SDIO_QUIRK (1 << 1) +#define ESDHC_VENDOR_SPEC_VSELECT (1 << 1) +#define ESDHC_VENDOR_SPEC_FRC_SDCLK_ON (1 << 8) + /* pltfm-specific */ #define ESDHC_HOST_CONTROL_LE 0x20 @@ -52,12 +60,20 @@ static inline void esdhc_set_clock(struct sdhci_host *host, unsigned int clock, unsigned int host_clock) { + struct device *dev; int pre_div = 2; int div = 1; - u32 temp; - - if (clock == 0) + u32 temp, val; + + dev = mmc_dev(host->mmc); + if (clock == 0) { + if (of_device_is_compatible(dev->of_node, "fsl,imx6q-usdhc")) { + val = readl(host->ioaddr + ESDHC_VENDOR_SPEC); + writel(val & ~ESDHC_VENDOR_SPEC_FRC_SDCLK_ON, + host->ioaddr + ESDHC_VENDOR_SPEC); + } goto out; + } temp = sdhci_readl(host, ESDHC_SYSTEM_CONTROL); temp &= ~(ESDHC_CLOCK_IPGEN | ESDHC_CLOCK_HCKEN | ESDHC_CLOCK_PEREN @@ -81,6 +97,13 @@ static inline void esdhc_set_clock(struct sdhci_host *host, unsigned int clock, | (div << ESDHC_DIVIDER_SHIFT) | (pre_div << ESDHC_PREDIV_SHIFT)); sdhci_writel(host, temp, ESDHC_SYSTEM_CONTROL); + + if (of_device_is_compatible(dev->of_node, "fsl,imx6q-usdhc")) { + val = readl(host->ioaddr + ESDHC_VENDOR_SPEC); + writel(val | ESDHC_VENDOR_SPEC_FRC_SDCLK_ON, + host->ioaddr + ESDHC_VENDOR_SPEC); + } + mdelay(1); out: host->clock = clock;
The signal voltage switch follow requires to shutdown and output clock in a specific sequence according to standard host controller v3.0 spec. In that timing, the card must really receive clock or not. However, for i.MX6Q, the uSDHC will not output clock even the clock is enabled until there is command or data in transfer on the bus, which will then cause singal voltage switch always to fail. For i.MX6Q, we clear ESDHC_VENDOR_SPEC_FRC_SDCLK_ON bit to let controller to gate off clock automatically and set that bit to force clock output if clock is on. This is required by SD3.0 support. Signed-off-by: Dong Aisheng <b29396@freescale.com> --- drivers/mmc/host/sdhci-esdhc-imx.c | 3 --- drivers/mmc/host/sdhci-esdhc.h | 29 ++++++++++++++++++++++++++--- 2 files changed, 26 insertions(+), 6 deletions(-)