@@ -571,6 +571,16 @@ static int mmc_decode_ext_csd(struct mmc_card *card, u8 *ext_csd)
card->ext_csd.ffu_capable =
(ext_csd[EXT_CSD_SUPPORTED_MODE] & 0x1) &&
!(ext_csd[EXT_CSD_FW_CONFIG] & 0x1);
+ card->ext_csd.psa =
+ ext_csd[EXT_CSD_PSA];
+ if (ext_csd[EXT_CSD_PSA_TIMEOUT] > 0) {
+ card->ext_csd.psa_timeout =
+ 100 *
+ (1 << ext_csd[EXT_CSD_PSA_TIMEOUT]);
+ } else {
+ pr_warn("%s: EXT_CSD PSA Timeout is zero\n",
+ mmc_hostname(card->host));
+ }format-patch
}
out:
return err;
@@ -1331,6 +1341,24 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr,
mmc_set_dsr(host);
/*
+ * eMMC v5.0 or later
+ * and Production State Awareness state is
+ * EXT_CSD_PSA_POST_SOLDERING_WRITES (0x02)
+ * The host should set the device to NORMAL mode
+ */
+ if ((card->ext_csd.rev >= 7) &&
+ (card->ext_csd.psa == EXT_CSD_PSA_POST_SOLDERING_WRITES)) {
+ unsigned int timeout;
+
+ timeout = DIV_ROUND_UP(card->ext_csd.psa_timeout, 1000);
+ card->ext_csd.psa = EXT_CSD_PSA_NORMAL;
+ err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
+ EXT_CSD_PSA, card->ext_csd.psa, timeout);
+ if (err && err != -EBADMSG)
+ goto free_card;
+ }
+
+ /*
* Select card, as all following commands rely on that.
*/
if (!mmc_host_is_spi(host)) {
@@ -60,9 +60,11 @@ struct mmc_ext_csd {
u8 packed_event_en;
unsigned int part_time; /* Units: ms */
unsigned int sa_timeout; /* Units: 100ns */
+ unsigned int psa_timeout; /* Units: 100us */
unsigned int generic_cmd6_time; /* Units: 10ms */
unsigned int power_off_longtime; /* Units: ms */
u8 power_off_notification; /* state */
+ u8 psa; /* production state awareness */
unsigned int hs_max_dtr;
unsigned int hs200_max_dtr;
#define MMC_HIGH_26_MAX_DTR 26000000
@@ -285,6 +285,7 @@ struct _mmc_csd {
#define EXT_CSD_EXP_EVENTS_STATUS 54 /* RO, 2 bytes */
#define EXT_CSD_EXP_EVENTS_CTRL 56 /* R/W, 2 bytes */
#define EXT_CSD_DATA_SECTOR_SIZE 61 /* R */
+#define EXT_CSD_PSA 133 /* R/W/E */
#define EXT_CSD_GP_SIZE_MULT 143 /* R/W */
#define EXT_CSD_PARTITION_SETTING_COMPLETED 155 /* R/W */
#define EXT_CSD_PARTITION_ATTRIBUTE 156 /* R/W */
@@ -315,6 +316,7 @@ struct _mmc_csd {
#define EXT_CSD_PWR_CL_26_360 203 /* RO */
#define EXT_CSD_SEC_CNT 212 /* RO, 4 bytes */
#define EXT_CSD_S_A_TIMEOUT 217 /* RO */
+#define EXT_CSD_PSA_TIMEOUT 218 /* RO */
#define EXT_CSD_REL_WR_SEC_C 222 /* RO */
#define EXT_CSD_HC_WP_GRP_SIZE 221 /* RO */
#define EXT_CSD_ERASE_TIMEOUT_MULT 223 /* RO */
@@ -433,6 +435,12 @@ struct _mmc_csd {
#define EXT_CSD_BKOPS_LEVEL_2 0x2
/*
+ * PRODUCTION STATE AWARENESS fields
+ */
+#define EXT_CSD_PSA_NORMAL 0x00
+#define EXT_CSD_PSA_POST_SOLDERING_WRITES 0x02
+
+/*
* MMC_SWITCH access modes
*/
In this patch driver should recognize if eMMC device (Rev >=5.0) was left in PRE_SOLDERING_POST_WRITES (0x02) state, and switch it to NORMAL (0x00). PRE_SOLDERING_POST_WRITES (0x02) state - represents a state where the device is in production process and the host (usually programmer) completed loading the content to the device. The host (usually programmer) sets the device to this state after loading the content and just before soldering. After soldering the device to the real host (not programmer), the device should be switched to NORMAL (0x00) mode. The NORMAL (0x00) mode of PSA register represents a state in which the device is running in the field and uses regular operations. Leaving device in PRE_SOLDERING_POST_WRITES (0x02) might cause unexpected behaviour of eMMC device. More details about PSA feature can be found in eMMC5.0 JEDEC spec (JESD84-B50.pdf): http://www.jedec.org/standards-documents/technology-focus-areas/flash-memory-ssds-ufs-emmc/e-mmc Signed-off-by: Alex Lemberg <alex.lemberg@sandisk.com> ---