@@ -290,8 +290,6 @@ static unsigned long balloon3_mmc_pin_config[] __initdata = {
static struct pxamci_platform_data balloon3_mci_platform_data = {
.ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
- .gpio_card_detect = -1,
- .gpio_card_ro = -1,
.gpio_power = -1,
.detect_delay_ms = 200,
};
@@ -12,6 +12,7 @@
#include <linux/platform_device.h>
#include <linux/irq.h>
#include <linux/gpio.h>
+#include <linux/gpio/machine.h>
#include <linux/delay.h>
#include <linux/platform_data/rtc-v3020.h>
@@ -30,11 +31,6 @@
/* physical address if local-bus attached devices */
#define RTC_PHYS_BASE (PXA_CS1_PHYS + (5 << 22))
-/* GPIO IRQ usage */
-#define GPIO83_MMC_IRQ (83)
-
-#define CMX270_MMC_IRQ PXA_GPIO_TO_IRQ(GPIO83_MMC_IRQ)
-
/* MMC power enable */
#define GPIO105_MMC_POWER (105)
@@ -288,14 +284,22 @@ static inline void cmx270_init_ohci(void) {}
#if defined(CONFIG_MMC) || defined(CONFIG_MMC_MODULE)
static struct pxamci_platform_data cmx270_mci_platform_data = {
.ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
- .gpio_card_detect = GPIO83_MMC_IRQ,
- .gpio_card_ro = -1,
.gpio_power = GPIO105_MMC_POWER,
.gpio_power_invert = 1,
};
+static struct gpiod_lookup_table cmx270_mci_gpio_table = {
+ .dev_id = "pxa2xx-mci.0",
+ .table = {
+ /* Card detect on GPIO 83 */
+ GPIO_LOOKUP("gpio-pxa", 83, "cd", GPIO_ACTIVE_LOW),
+ { },
+ },
+};
+
static void __init cmx270_init_mmc(void)
{
+ gpiod_add_lookup_table(&cmx270_mci_gpio_table);
pxa_set_mci_info(&cmx270_mci_platform_data);
}
#else
@@ -64,11 +64,6 @@
#define CM_X300_ETH_PHYS 0x08000010
-#define GPIO82_MMC_IRQ (82)
-#define GPIO85_MMC_WP (85)
-
-#define CM_X300_MMC_IRQ PXA_GPIO_TO_IRQ(GPIO82_MMC_IRQ)
-
#define GPIO95_RTC_CS (95)
#define GPIO96_RTC_WR (96)
#define GPIO97_RTC_RD (97)
@@ -459,11 +454,20 @@ static inline void cm_x300_init_nand(void) {}
static struct pxamci_platform_data cm_x300_mci_platform_data = {
.detect_delay_ms = 200,
.ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
- .gpio_card_detect = GPIO82_MMC_IRQ,
- .gpio_card_ro = GPIO85_MMC_WP,
.gpio_power = -1,
};
+static struct gpiod_lookup_table cm_x300_mci_gpio_table = {
+ .dev_id = "pxa2xx-mci.0",
+ .table = {
+ /* Card detect on GPIO 82 */
+ GPIO_LOOKUP("gpio-pxa", 82, "cd", GPIO_ACTIVE_LOW),
+ /* Write protect on GPIO 85 */
+ GPIO_LOOKUP("gpio-pxa", 85, "wp", GPIO_ACTIVE_LOW),
+ { },
+ },
+};
+
/* The second MMC slot of CM-X300 is hardwired to Libertas card and has
no detection/ro pins */
static int cm_x300_mci2_init(struct device *dev,
@@ -482,13 +486,12 @@ static struct pxamci_platform_data cm_x300_mci2_platform_data = {
.ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
.init = cm_x300_mci2_init,
.exit = cm_x300_mci2_exit,
- .gpio_card_detect = -1,
- .gpio_card_ro = -1,
.gpio_power = -1,
};
static void __init cm_x300_init_mmc(void)
{
+ gpiod_add_lookup_table(&cm_x300_mci_gpio_table);
pxa_set_mci_info(&cm_x300_mci_platform_data);
pxa3xx_set_mci2_info(&cm_x300_mci2_platform_data);
}
@@ -14,7 +14,7 @@
#include <linux/kernel.h>
#include <linux/platform_device.h>
#include <linux/interrupt.h>
-#include <linux/gpio.h>
+#include <linux/gpio/machine.h>
#include <asm/mach-types.h>
#include <mach/hardware.h>
#include <asm/mach/arch.h>
@@ -37,22 +37,44 @@
#if defined(CONFIG_MMC_PXA) || defined(CONFIG_MMC_PXA_MODULE)
static struct pxamci_platform_data colibri_mci_platform_data = {
.ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
- .gpio_power = -1,
- .gpio_card_ro = -1,
.detect_delay_ms = 200,
};
+static struct gpiod_lookup_table colibri_pxa270_mci_gpio_table = {
+ .dev_id = "pxa2xx-mci.0",
+ .table = {
+ GPIO_LOOKUP("gpio-pxa", GPIO0_COLIBRI_PXA270_SD_DETECT,
+ "cd", GPIO_ACTIVE_LOW),
+ { },
+ },
+};
+
+static struct gpiod_lookup_table colibri_pxa300_mci_gpio_table = {
+ .dev_id = "pxa2xx-mci.0",
+ .table = {
+ GPIO_LOOKUP("gpio-pxa", GPIO13_COLIBRI_PXA300_SD_DETECT,
+ "cd", GPIO_ACTIVE_LOW),
+ { },
+ },
+};
+
+static struct gpiod_lookup_table colibri_pxa320_mci_gpio_table = {
+ .dev_id = "pxa2xx-mci.0",
+ .table = {
+ GPIO_LOOKUP("gpio-pxa", GPIO28_COLIBRI_PXA320_SD_DETECT,
+ "cd", GPIO_ACTIVE_LOW),
+ { },
+ },
+};
+
static void __init colibri_mmc_init(void)
{
if (machine_is_colibri()) /* PXA270 Colibri */
- colibri_mci_platform_data.gpio_card_detect =
- GPIO0_COLIBRI_PXA270_SD_DETECT;
+ gpiod_add_lookup_table(&colibri_pxa270_mci_gpio_table);
if (machine_is_colibri300()) /* PXA300 Colibri */
- colibri_mci_platform_data.gpio_card_detect =
- GPIO13_COLIBRI_PXA300_SD_DETECT;
+ gpiod_add_lookup_table(&colibri_pxa300_mci_gpio_table);
else /* PXA320 Colibri */
- colibri_mci_platform_data.gpio_card_detect =
- GPIO28_COLIBRI_PXA320_SD_DETECT;
+ gpiod_add_lookup_table(&colibri_pxa320_mci_gpio_table);
pxa_set_mci_info(&colibri_mci_platform_data);
}
@@ -14,7 +14,7 @@
#include <linux/bitops.h>
#include <linux/delay.h>
-#include <linux/gpio.h>
+#include <linux/gpio/machine.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/leds.h>
@@ -39,8 +39,6 @@
#include "generic.h"
#define GPIO114_INCOME_ETH_IRQ (114)
-#define GPIO0_INCOME_SD_DETECT (0)
-#define GPIO0_INCOME_SD_RO (1)
#define GPIO54_INCOME_LED_A (54)
#define GPIO55_INCOME_LED_B (55)
#define GPIO113_INCOME_TS_IRQ (113)
@@ -52,13 +50,23 @@
static struct pxamci_platform_data income_mci_platform_data = {
.ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
.gpio_power = -1,
- .gpio_card_detect = GPIO0_INCOME_SD_DETECT,
- .gpio_card_ro = GPIO0_INCOME_SD_RO,
.detect_delay_ms = 200,
};
+static struct gpiod_lookup_table income_mci_gpio_table = {
+ .dev_id = "pxa2xx-mci.0",
+ .table = {
+ /* Card detect on GPIO 0 */
+ GPIO_LOOKUP("gpio-pxa", 0, "cd", GPIO_ACTIVE_LOW),
+ /* Write protect on GPIO 1 */
+ GPIO_LOOKUP("gpio-pxa", 1, "wp", GPIO_ACTIVE_LOW),
+ { },
+ },
+};
+
static void __init income_mmc_init(void)
{
+ gpiod_add_lookup_table(&income_mci_gpio_table);
pxa_set_mci_info(&income_mci_platform_data);
}
#else
@@ -24,6 +24,7 @@
#include <linux/mtd/physmap.h>
#include <linux/pm.h>
#include <linux/gpio.h>
+#include <linux/gpio/machine.h>
#include <linux/backlight.h>
#include <linux/i2c.h>
#include <linux/platform_data/i2c-pxa.h>
@@ -493,11 +494,21 @@ static struct platform_device corgi_audio_device = {
static struct pxamci_platform_data corgi_mci_platform_data = {
.detect_delay_ms = 250,
.ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
- .gpio_card_detect = CORGI_GPIO_nSD_DETECT,
- .gpio_card_ro = CORGI_GPIO_nSD_WP,
.gpio_power = CORGI_GPIO_SD_PWR,
};
+static struct gpiod_lookup_table corgi_mci_gpio_table = {
+ .dev_id = "pxa2xx-mci.0",
+ .table = {
+ /* Card detect on GPIO 9 */
+ GPIO_LOOKUP("gpio-pxa", CORGI_GPIO_nSD_DETECT,
+ "cd", GPIO_ACTIVE_LOW),
+ /* Write protect on GPIO 7 */
+ GPIO_LOOKUP("gpio-pxa", CORGI_GPIO_nSD_WP,
+ "wp", GPIO_ACTIVE_LOW),
+ { },
+ },
+};
/*
* Irda
@@ -731,6 +742,7 @@ static void __init corgi_init(void)
corgi_init_spi();
pxa_set_udc_info(&udc_info);
+ gpiod_add_lookup_table(&corgi_mci_gpio_table);
pxa_set_mci_info(&corgi_mci_platform_data);
pxa_set_ficp_info(&corgi_ficp_platform_data);
pxa_set_i2c_info(NULL);
@@ -11,7 +11,7 @@
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/io.h>
-#include <linux/gpio.h>
+#include <linux/gpio/machine.h>
#include <linux/platform_device.h>
#include <linux/mtd/physmap.h>
#include <linux/mtd/partitions.h>
@@ -129,11 +129,22 @@ static struct pxamci_platform_data csb726_mci = {
.detect_delay_ms = 500,
.ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
/* FIXME setpower */
- .gpio_card_detect = CSB726_GPIO_MMC_DETECT,
- .gpio_card_ro = CSB726_GPIO_MMC_RO,
.gpio_power = -1,
};
+static struct gpiod_lookup_table csb726_mci_gpio_table = {
+ .dev_id = "pxa2xx-mci.0",
+ .table = {
+ /* Card detect on GPIO 100 */
+ GPIO_LOOKUP("gpio-pxa", CSB726_GPIO_MMC_DETECT,
+ "cd", GPIO_ACTIVE_LOW),
+ /* Write protect on GPIO 101 */
+ GPIO_LOOKUP("gpio-pxa", CSB726_GPIO_MMC_RO,
+ "wp", GPIO_ACTIVE_LOW),
+ { },
+ },
+};
+
static struct pxaohci_platform_data csb726_ohci_platform_data = {
.port_mode = PMM_NPS_MODE,
.flags = ENABLE_PORT1 | NO_OC_PROTECTION,
@@ -264,6 +275,7 @@ static void __init csb726_init(void)
pxa_set_stuart_info(NULL);
pxa_set_i2c_info(NULL);
pxa27x_set_i2c_power_info(NULL);
+ gpiod_add_lookup_table(&csb726_mci_gpio_table);
pxa_set_mci_info(&csb726_mci);
pxa_set_ohci_info(&csb726_ohci_platform_data);
pxa_set_ac97_info(NULL);
@@ -20,6 +20,7 @@
#include <linux/input.h>
#include <linux/gpio_keys.h>
#include <linux/gpio.h>
+#include <linux/gpio/machine.h>
#include <linux/mfd/da903x.h>
#include <linux/regulator/machine.h>
#include <linux/regulator/fixed.h>
@@ -546,6 +547,15 @@ static inline void em_x270_init_ohci(void) {}
#if defined(CONFIG_MMC) || defined(CONFIG_MMC_MODULE)
static struct regulator *em_x270_sdio_ldo;
+static struct gpiod_lookup_table em_x270_mci_wp_gpio_table = {
+ .dev_id = "pxa2xx-mci.0",
+ .table = {
+ /* Write protect on GPIO 95 */
+ GPIO_LOOKUP("gpio-pxa", GPIO95_MMC_WP, "wp", GPIO_ACTIVE_LOW),
+ { },
+ },
+};
+
static int em_x270_mci_init(struct device *dev,
irq_handler_t em_x270_detect_int,
void *data)
@@ -567,15 +577,7 @@ static int em_x270_mci_init(struct device *dev,
goto err_irq;
}
- if (machine_is_em_x270()) {
- err = gpio_request(GPIO95_MMC_WP, "MMC WP");
- if (err) {
- dev_err(dev, "can't request MMC write protect: %d\n",
- err);
- goto err_gpio_wp;
- }
- gpio_direction_input(GPIO95_MMC_WP);
- } else {
+ if (!machine_is_em_x270()) {
err = gpio_request(GPIO38_SD_PWEN, "sdio power");
if (err) {
dev_err(dev, "can't request MMC power control : %d\n",
@@ -615,17 +617,10 @@ static void em_x270_mci_exit(struct device *dev, void *data)
free_irq(gpio_to_irq(mmc_cd), data);
regulator_put(em_x270_sdio_ldo);
- if (machine_is_em_x270())
- gpio_free(GPIO95_MMC_WP);
- else
+ if (!machine_is_em_x270())
gpio_free(GPIO38_SD_PWEN);
}
-static int em_x270_mci_get_ro(struct device *dev)
-{
- return gpio_get_value(GPIO95_MMC_WP);
-}
-
static struct pxamci_platform_data em_x270_mci_platform_data = {
.detect_delay_ms = 250,
.ocr_mask = MMC_VDD_20_21|MMC_VDD_21_22|MMC_VDD_22_23|
@@ -635,15 +630,13 @@ static struct pxamci_platform_data em_x270_mci_platform_data = {
.init = em_x270_mci_init,
.setpower = em_x270_mci_setpower,
.exit = em_x270_mci_exit,
- .gpio_card_detect = -1,
- .gpio_card_ro = -1,
.gpio_power = -1,
};
static void __init em_x270_init_mmc(void)
{
if (machine_is_em_x270())
- em_x270_mci_platform_data.get_ro = em_x270_mci_get_ro;
+ gpiod_add_lookup_table(&em_x270_mci_wp_gpio_table);
pxa_set_mci_info(&em_x270_mci_platform_data);
}
@@ -90,8 +90,6 @@ static struct platform_device *devices[] __initdata = {
#ifdef CONFIG_MMC_PXA
static struct pxamci_platform_data gumstix_mci_platform_data = {
.ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
- .gpio_card_detect = -1,
- .gpio_card_ro = -1,
.gpio_power = -1,
};
@@ -160,8 +160,6 @@ static struct pxafb_mach_info sharp_lm8v31 = {
static struct pxamci_platform_data idp_mci_platform_data = {
.ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
- .gpio_card_detect = -1,
- .gpio_card_ro = -1,
.gpio_power = -1,
};
@@ -20,7 +20,7 @@
#include <linux/delay.h>
#include <linux/platform_device.h>
#include <linux/clk.h>
-#include <linux/gpio.h>
+#include <linux/gpio/machine.h>
#include <linux/spi/spi.h>
#include <linux/spi/pxa2xx_spi.h>
#include <linux/smc91x.h>
@@ -51,8 +51,6 @@
#include "generic.h"
-#define GPIO_MMC1_CARD_DETECT mfp_to_gpio(MFP_PIN_GPIO15)
-
/* Littleton MFP configurations */
static mfp_cfg_t littleton_mfp_cfg[] __initdata = {
/* LCD */
@@ -278,13 +276,21 @@ static inline void littleton_init_keypad(void) {}
static struct pxamci_platform_data littleton_mci_platform_data = {
.detect_delay_ms = 200,
.ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
- .gpio_card_detect = GPIO_MMC1_CARD_DETECT,
- .gpio_card_ro = -1,
.gpio_power = -1,
};
+static struct gpiod_lookup_table littleton_mci_gpio_table = {
+ .dev_id = "pxa2xx-mci.0",
+ .table = {
+ /* Card detect on MFP (gpio-pxa) GPIO 15 */
+ GPIO_LOOKUP("gpio-pxa", 15, "cd", GPIO_ACTIVE_LOW),
+ { },
+ },
+};
+
static void __init littleton_init_mmc(void)
{
+ gpiod_add_lookup_table(&littleton_mci_gpio_table);
pxa_set_mci_info(&littleton_mci_platform_data);
}
#else
@@ -440,8 +440,6 @@ static struct pxamci_platform_data lubbock_mci_platform_data = {
.init = lubbock_mci_init,
.get_ro = lubbock_mci_get_ro,
.exit = lubbock_mci_exit,
- .gpio_card_detect = -1,
- .gpio_card_ro = -1,
.gpio_power = -1,
};
@@ -775,12 +775,22 @@ static struct pxamci_platform_data magician_mci_info = {
.ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
.init = magician_mci_init,
.exit = magician_mci_exit,
- .gpio_card_detect = -1,
- .gpio_card_ro = EGPIO_MAGICIAN_nSD_READONLY,
.gpio_card_ro_invert = 1,
.gpio_power = EGPIO_MAGICIAN_SD_POWER,
};
+static struct gpiod_lookup_table magician_mci_gpio_table = {
+ .dev_id = "pxa2xx-mci.0",
+ .table = {
+ /*
+ * Write protect on EGPIO register 5 index 4, this is
+ * on the second HTC EGPIO chip which starts at regiser
+ * 4, so we need offset 8+4=12 on that particular chip.
+ */
+ GPIO_LOOKUP("htc-egpio-1", 12, "wp", GPIO_ACTIVE_HIGH),
+ { },
+ },
+};
/*
* USB OHCI
@@ -979,6 +989,7 @@ static void __init magician_init(void)
i2c_register_board_info(1,
ARRAY_AND_SIZE(magician_pwr_i2c_board_info));
+ gpiod_add_lookup_table(&magician_mci_gpio_table);
pxa_set_mci_info(&magician_mci_info);
pxa_set_ohci_info(&magician_ohci_info);
pxa_set_udc_info(&magician_udc_info);
@@ -361,8 +361,6 @@ static struct pxamci_platform_data mainstone_mci_platform_data = {
.init = mainstone_mci_init,
.setpower = mainstone_mci_setpower,
.exit = mainstone_mci_exit,
- .gpio_card_detect = -1,
- .gpio_card_ro = -1,
.gpio_power = -1,
};
@@ -31,6 +31,7 @@
#include <linux/rtc.h>
#include <linux/leds.h>
#include <linux/gpio.h>
+#include <linux/gpio/machine.h>
#include <linux/interrupt.h>
#include <linux/irq.h>
#include <linux/pda_power.h>
@@ -397,11 +398,20 @@ struct gpio_vbus_mach_info gpio_vbus_data = {
static struct pxamci_platform_data mioa701_mci_info = {
.detect_delay_ms = 250,
.ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
- .gpio_card_detect = GPIO15_SDIO_INSERT,
- .gpio_card_ro = GPIO78_SDIO_RO,
.gpio_power = GPIO91_SDIO_EN,
};
+static struct gpiod_lookup_table mioa701_mci_gpio_table = {
+ .dev_id = "pxa2xx-mci.0",
+ .table = {
+ /* Card detect on GPIO 15 */
+ GPIO_LOOKUP("gpio-pxa", 15, "cd", GPIO_ACTIVE_LOW),
+ /* Write protect on GPIO 78 */
+ GPIO_LOOKUP("gpio-pxa", 78, "wp", GPIO_ACTIVE_LOW),
+ { },
+ },
+};
+
/* FlashRAM */
static struct resource docg3_resource = {
.start = PXA_CS0_PHYS,
@@ -743,6 +753,7 @@ static void __init mioa701_machine_init(void)
pr_err("MioA701: Failed to request GPIOs: %d", rc);
bootstrap_init();
pxa_set_fb_info(NULL, &mioa701_pxafb_info);
+ gpiod_add_lookup_table(&mioa701_mci_gpio_table);
pxa_set_mci_info(&mioa701_mci_info);
pxa_set_keypad_info(&mioa701_keypad_info);
pxa_set_udc_info(&mioa701_udc_info);
@@ -21,7 +21,7 @@
#include <linux/serial_8250.h>
#include <linux/dm9000.h>
-#include <linux/gpio.h>
+#include <linux/gpio/machine.h>
#include <linux/platform_data/i2c-pxa.h>
#include <linux/platform_data/mtd-nand-pxa3xx.h>
@@ -326,13 +326,23 @@ static mfp_cfg_t mfp_cfg[] __initdata = {
static struct pxamci_platform_data mxm_8x10_mci_platform_data = {
.ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
.detect_delay_ms = 10,
- .gpio_card_detect = MXM_8X10_SD_nCD,
- .gpio_card_ro = MXM_8X10_SD_WP,
.gpio_power = -1
};
+static struct gpiod_lookup_table mxm_8x10_mci_gpio_table = {
+ .dev_id = "pxa2xx-mci.0",
+ .table = {
+ /* Card detect on GPIO 72 */
+ GPIO_LOOKUP("gpio-pxa", 72, "cd", GPIO_ACTIVE_LOW),
+ /* Write protect on GPIO 84 */
+ GPIO_LOOKUP("gpio-pxa", 84, "wp", GPIO_ACTIVE_LOW),
+ { },
+ },
+};
+
void __init mxm_8x10_mmc_init(void)
{
+ gpiod_add_lookup_table(&mxm_8x10_mci_gpio_table);
pxa_set_mci_info(&mxm_8x10_mci_platform_data);
}
#endif
@@ -49,14 +49,14 @@ static struct pxamci_platform_data palm27x_mci_platform_data = {
.detect_delay_ms = 200,
};
-void __init palm27x_mmc_init(int detect, int ro, int power,
- int power_inverted)
+void __init palm27x_mmc_init(struct gpiod_lookup_table *gtable, int power,
+ int power_inverted)
{
- palm27x_mci_platform_data.gpio_card_detect = detect;
- palm27x_mci_platform_data.gpio_card_ro = ro;
palm27x_mci_platform_data.gpio_power = power;
palm27x_mci_platform_data.gpio_power_invert = power_inverted;
+ if (gtable)
+ gpiod_add_lookup_table(gtable);
pxa_set_mci_info(&palm27x_mci_platform_data);
}
#endif
@@ -12,12 +12,16 @@
#ifndef __INCLUDE_MACH_PALM27X__
#define __INCLUDE_MACH_PALM27X__
+#include <linux/gpio/machine.h>
+
#if defined(CONFIG_MMC_PXA) || defined(CONFIG_MMC_PXA_MODULE)
-extern void __init palm27x_mmc_init(int detect, int ro, int power,
- int power_inverted);
+extern void __init palm27x_mmc_init(struct gpiod_lookup_table *gtable,
+ int power,
+ int power_inverted);
#else
-static inline void palm27x_mmc_init(int detect, int ro, int power,
- int power_inverted)
+static inline void palm27x_mmc_init(struct gpiod_lookup_table *gtable,
+ int power,
+ int power_inverted)
{}
#endif
@@ -320,6 +320,17 @@ static void __init palmld_map_io(void)
iotable_init(palmld_io_desc, ARRAY_SIZE(palmld_io_desc));
}
+static struct gpiod_lookup_table palmld_mci_gpio_table = {
+ .dev_id = "pxa2xx-mci.0",
+ .table = {
+ GPIO_LOOKUP("gpio-pxa", GPIO_NR_PALMLD_SD_DETECT_N,
+ "cd", GPIO_ACTIVE_LOW),
+ GPIO_LOOKUP("gpio-pxa", GPIO_NR_PALMLD_SD_READONLY,
+ "wp", GPIO_ACTIVE_LOW),
+ { },
+ },
+};
+
static void __init palmld_init(void)
{
pxa2xx_mfp_config(ARRAY_AND_SIZE(palmld_pin_config));
@@ -327,8 +338,8 @@ static void __init palmld_init(void)
pxa_set_btuart_info(NULL);
pxa_set_stuart_info(NULL);
- palm27x_mmc_init(GPIO_NR_PALMLD_SD_DETECT_N, GPIO_NR_PALMLD_SD_READONLY,
- GPIO_NR_PALMLD_SD_POWER, 0);
+ palm27x_mmc_init(&palmld_mci_gpio_table,
+ GPIO_NR_PALMLD_SD_POWER, 0);
palm27x_pm_init(PALMLD_STR_BASE);
palm27x_lcd_init(-1, &palm_320x480_lcd_mode);
palm27x_irda_init(GPIO_NR_PALMLD_IR_DISABLE);
@@ -182,6 +182,17 @@ static void __init palmt5_reserve(void)
memblock_reserve(0xa0200000, 0x1000);
}
+static struct gpiod_lookup_table palmt5_mci_gpio_table = {
+ .dev_id = "pxa2xx-mci.0",
+ .table = {
+ GPIO_LOOKUP("gpio-pxa", GPIO_NR_PALMT5_SD_DETECT_N,
+ "cd", GPIO_ACTIVE_LOW),
+ GPIO_LOOKUP("gpio-pxa", GPIO_NR_PALMT5_SD_READONLY,
+ "wp", GPIO_ACTIVE_LOW),
+ { },
+ },
+};
+
static void __init palmt5_init(void)
{
pxa2xx_mfp_config(ARRAY_AND_SIZE(palmt5_pin_config));
@@ -189,8 +200,8 @@ static void __init palmt5_init(void)
pxa_set_btuart_info(NULL);
pxa_set_stuart_info(NULL);
- palm27x_mmc_init(GPIO_NR_PALMT5_SD_DETECT_N, GPIO_NR_PALMT5_SD_READONLY,
- GPIO_NR_PALMT5_SD_POWER, 0);
+ palm27x_mmc_init(&palmt5_mci_gpio_table,
+ GPIO_NR_PALMT5_SD_POWER, 0);
palm27x_pm_init(PALMT5_STR_BASE);
palm27x_lcd_init(-1, &palm_320x480_lcd_mode);
palm27x_udc_init(GPIO_NR_PALMT5_USB_DETECT_N,
@@ -20,7 +20,7 @@
#include <linux/input.h>
#include <linux/pwm.h>
#include <linux/pwm_backlight.h>
-#include <linux/gpio.h>
+#include <linux/gpio/machine.h>
#include <linux/input/matrix_keypad.h>
#include <linux/ucb1400.h>
#include <linux/power_supply.h>
@@ -121,13 +121,23 @@ static unsigned long palmtc_pin_config[] __initdata = {
static struct pxamci_platform_data palmtc_mci_platform_data = {
.ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
.gpio_power = GPIO_NR_PALMTC_SD_POWER,
- .gpio_card_ro = GPIO_NR_PALMTC_SD_READONLY,
- .gpio_card_detect = GPIO_NR_PALMTC_SD_DETECT_N,
.detect_delay_ms = 200,
};
+static struct gpiod_lookup_table palmtc_mci_gpio_table = {
+ .dev_id = "pxa2xx-mci.0",
+ .table = {
+ GPIO_LOOKUP("gpio-pxa", GPIO_NR_PALMTC_SD_DETECT_N,
+ "cd", GPIO_ACTIVE_LOW),
+ GPIO_LOOKUP("gpio-pxa", GPIO_NR_PALMTC_SD_READONLY,
+ "wp", GPIO_ACTIVE_LOW),
+ { },
+ },
+};
+
static void __init palmtc_mmc_init(void)
{
+ gpiod_add_lookup_table(&palmtc_mci_gpio_table);
pxa_set_mci_info(&palmtc_mci_platform_data);
}
#else
@@ -19,6 +19,7 @@
#include <linux/delay.h>
#include <linux/irq.h>
#include <linux/gpio_keys.h>
+#include <linux/gpio/machine.h>
#include <linux/input.h>
#include <linux/pda_power.h>
#include <linux/pwm.h>
@@ -101,11 +102,20 @@ static unsigned long palmte2_pin_config[] __initdata = {
******************************************************************************/
static struct pxamci_platform_data palmte2_mci_platform_data = {
.ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
- .gpio_card_detect = GPIO_NR_PALMTE2_SD_DETECT_N,
- .gpio_card_ro = GPIO_NR_PALMTE2_SD_READONLY,
.gpio_power = GPIO_NR_PALMTE2_SD_POWER,
};
+static struct gpiod_lookup_table palmte2_mci_gpio_table = {
+ .dev_id = "pxa2xx-mci.0",
+ .table = {
+ GPIO_LOOKUP("gpio-pxa", GPIO_NR_PALMTE2_SD_DETECT_N,
+ "cd", GPIO_ACTIVE_LOW),
+ GPIO_LOOKUP("gpio-pxa", GPIO_NR_PALMTE2_SD_READONLY,
+ "wp", GPIO_ACTIVE_LOW),
+ { },
+ },
+};
+
#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
/******************************************************************************
* GPIO keys
@@ -354,6 +364,7 @@ static void __init palmte2_init(void)
pxa_set_stuart_info(NULL);
pxa_set_fb_info(NULL, &palmte2_lcd_screen);
+ gpiod_add_lookup_table(&palmte2_mci_gpio_table);
pxa_set_mci_info(&palmte2_mci_platform_data);
palmte2_udc_init();
pxa_set_ac97_info(&palmte2_ac97_pdata);
@@ -480,23 +480,44 @@ void __init treo680_gpio_init(void)
gpio_free(GPIO_NR_TREO680_LCD_EN_N);
}
+static struct gpiod_lookup_table treo680_mci_gpio_table = {
+ .dev_id = "pxa2xx-mci.0",
+ .table = {
+ GPIO_LOOKUP("gpio-pxa", GPIO_NR_TREO_SD_DETECT_N,
+ "cd", GPIO_ACTIVE_LOW),
+ GPIO_LOOKUP("gpio-pxa", GPIO_NR_TREO680_SD_READONLY,
+ "wp", GPIO_ACTIVE_LOW),
+ { },
+ },
+};
+
static void __init treo680_init(void)
{
pxa2xx_mfp_config(ARRAY_AND_SIZE(treo680_pin_config));
palmphone_common_init();
treo680_gpio_init();
- palm27x_mmc_init(GPIO_NR_TREO_SD_DETECT_N, GPIO_NR_TREO680_SD_READONLY,
- GPIO_NR_TREO680_SD_POWER, 0);
+ palm27x_mmc_init(&treo680_mci_gpio_table,
+ GPIO_NR_TREO680_SD_POWER, 0);
}
#endif
#ifdef CONFIG_MACH_CENTRO
+
+static struct gpiod_lookup_table centro685_mci_gpio_table = {
+ .dev_id = "pxa2xx-mci.0",
+ .table = {
+ GPIO_LOOKUP("gpio-pxa", GPIO_NR_TREO_SD_DETECT_N,
+ "cd", GPIO_ACTIVE_LOW),
+ { },
+ },
+};
+
static void __init centro_init(void)
{
pxa2xx_mfp_config(ARRAY_AND_SIZE(centro685_pin_config));
palmphone_common_init();
- palm27x_mmc_init(GPIO_NR_TREO_SD_DETECT_N, -1,
- GPIO_NR_CENTRO_SD_POWER, 1);
+ palm27x_mmc_init(¢ro685_mci_gpio_table,
+ GPIO_NR_CENTRO_SD_POWER, 1);
}
#endif
@@ -337,6 +337,17 @@ static void __init palmtx_map_io(void)
iotable_init(palmtx_io_desc, ARRAY_SIZE(palmtx_io_desc));
}
+static struct gpiod_lookup_table palmtx_mci_gpio_table = {
+ .dev_id = "pxa2xx-mci.0",
+ .table = {
+ GPIO_LOOKUP("gpio-pxa", GPIO_NR_PALMTX_SD_DETECT_N,
+ "cd", GPIO_ACTIVE_LOW),
+ GPIO_LOOKUP("gpio-pxa", GPIO_NR_PALMTX_SD_READONLY,
+ "wp", GPIO_ACTIVE_LOW),
+ { },
+ },
+};
+
static void __init palmtx_init(void)
{
pxa2xx_mfp_config(ARRAY_AND_SIZE(palmtx_pin_config));
@@ -344,8 +355,8 @@ static void __init palmtx_init(void)
pxa_set_btuart_info(NULL);
pxa_set_stuart_info(NULL);
- palm27x_mmc_init(GPIO_NR_PALMTX_SD_DETECT_N, GPIO_NR_PALMTX_SD_READONLY,
- GPIO_NR_PALMTX_SD_POWER, 0);
+ palm27x_mmc_init(&palmtx_mci_gpio_table,
+ GPIO_NR_PALMTX_SD_POWER, 0);
palm27x_pm_init(PALMTX_STR_BASE);
palm27x_lcd_init(-1, &palm_320x480_lcd_mode);
palm27x_udc_init(GPIO_NR_PALMTX_USB_DETECT_N,
@@ -386,6 +386,17 @@ static void __init palmz72_camera_init(void)
static inline void palmz72_camera_init(void) {}
#endif
+static struct gpiod_lookup_table palmz72_mci_gpio_table = {
+ .dev_id = "pxa2xx-mci.0",
+ .table = {
+ GPIO_LOOKUP("gpio-pxa", GPIO_NR_PALMZ72_SD_DETECT_N,
+ "cd", GPIO_ACTIVE_LOW),
+ GPIO_LOOKUP("gpio-pxa", GPIO_NR_PALMZ72_SD_RO,
+ "wp", GPIO_ACTIVE_LOW),
+ { },
+ },
+};
+
/******************************************************************************
* Machine init
******************************************************************************/
@@ -396,8 +407,8 @@ static void __init palmz72_init(void)
pxa_set_btuart_info(NULL);
pxa_set_stuart_info(NULL);
- palm27x_mmc_init(GPIO_NR_PALMZ72_SD_DETECT_N, GPIO_NR_PALMZ72_SD_RO,
- GPIO_NR_PALMZ72_SD_POWER_N, 1);
+ palm27x_mmc_init(&palmz72_mci_gpio_table,
+ GPIO_NR_PALMZ72_SD_POWER_N, 1);
palm27x_lcd_init(-1, &palm_320x320_lcd_mode);
palm27x_udc_init(GPIO_NR_PALMZ72_USB_DETECT_N,
GPIO_NR_PALMZ72_USB_PULLUP, 0);
@@ -370,8 +370,6 @@ static struct pxamci_platform_data pcm990_mci_platform_data = {
.init = pcm990_mci_init,
.setpower = pcm990_mci_setpower,
.exit = pcm990_mci_exit,
- .gpio_card_detect = -1,
- .gpio_card_ro = -1,
.gpio_power = -1,
};
@@ -23,6 +23,7 @@
#include <linux/delay.h>
#include <linux/mtd/physmap.h>
#include <linux/gpio.h>
+#include <linux/gpio/machine.h>
#include <linux/i2c.h>
#include <linux/platform_data/i2c-pxa.h>
#include <linux/regulator/machine.h>
@@ -288,11 +289,19 @@ static struct pxamci_platform_data poodle_mci_platform_data = {
.init = poodle_mci_init,
.setpower = poodle_mci_setpower,
.exit = poodle_mci_exit,
- .gpio_card_detect = POODLE_GPIO_nSD_DETECT,
- .gpio_card_ro = POODLE_GPIO_nSD_WP,
.gpio_power = -1,
};
+static struct gpiod_lookup_table poodle_mci_gpio_table = {
+ .dev_id = "pxa2xx-mci.0",
+ .table = {
+ GPIO_LOOKUP("gpio-pxa", POODLE_GPIO_nSD_DETECT,
+ "cd", GPIO_ACTIVE_LOW),
+ GPIO_LOOKUP("gpio-pxa", POODLE_GPIO_nSD_WP,
+ "wp", GPIO_ACTIVE_LOW),
+ { },
+ },
+};
/*
* Irda
@@ -439,6 +448,7 @@ static void __init poodle_init(void)
pxa_set_fb_info(&poodle_locomo_device.dev, &poodle_fb_info);
pxa_set_udc_info(&udc_info);
+ gpiod_add_lookup_table(&poodle_mci_gpio_table);
pxa_set_mci_info(&poodle_mci_platform_data);
pxa_set_ficp_info(&poodle_ficp_platform_data);
pxa_set_i2c_info(NULL);
@@ -749,8 +749,6 @@ static struct pxamci_platform_data raumfeld_mci_platform_data = {
.init = raumfeld_mci_init,
.exit = raumfeld_mci_exit,
.detect_delay_ms = 200,
- .gpio_card_detect = -1,
- .gpio_card_ro = -1,
.gpio_power = -1,
};
@@ -18,6 +18,7 @@
#include <linux/delay.h>
#include <linux/gpio_keys.h>
#include <linux/gpio.h>
+#include <linux/gpio/machine.h>
#include <linux/leds.h>
#include <linux/i2c.h>
#include <linux/platform_data/i2c-pxa.h>
@@ -615,13 +616,23 @@ static struct pxamci_platform_data spitz_mci_platform_data = {
.detect_delay_ms = 250,
.ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
.setpower = spitz_mci_setpower,
- .gpio_card_detect = SPITZ_GPIO_nSD_DETECT,
- .gpio_card_ro = SPITZ_GPIO_nSD_WP,
.gpio_power = -1,
};
+static struct gpiod_lookup_table spitz_mci_gpio_table = {
+ .dev_id = "pxa2xx-mci.0",
+ .table = {
+ GPIO_LOOKUP("gpio-pxa", SPITZ_GPIO_nSD_DETECT,
+ "cd", GPIO_ACTIVE_LOW),
+ GPIO_LOOKUP("gpio-pxa", SPITZ_GPIO_nSD_WP,
+ "wp", GPIO_ACTIVE_LOW),
+ { },
+ },
+};
+
static void __init spitz_mmc_init(void)
{
+ gpiod_add_lookup_table(&spitz_mci_gpio_table);
pxa_set_mci_info(&spitz_mci_platform_data);
}
#else
@@ -436,8 +436,6 @@ static int imote2_mci_get_ro(struct device *dev)
static struct pxamci_platform_data imote2_mci_platform_data = {
.ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34, /* default anyway */
.get_ro = imote2_mci_get_ro,
- .gpio_card_detect = -1,
- .gpio_card_ro = -1,
.gpio_power = -1,
};
@@ -31,6 +31,7 @@
#include <linux/gpio_keys.h>
#include <linux/input.h>
#include <linux/gpio.h>
+#include <linux/gpio/machine.h>
#include <linux/power/gpio-charger.h>
#include <linux/spi/spi.h>
#include <linux/spi/pxa2xx_spi.h>
@@ -291,11 +292,20 @@ static struct pxamci_platform_data tosa_mci_platform_data = {
.ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
.init = tosa_mci_init,
.exit = tosa_mci_exit,
- .gpio_card_detect = TOSA_GPIO_nSD_DETECT,
- .gpio_card_ro = TOSA_GPIO_SD_WP,
.gpio_power = TOSA_GPIO_PWR_ON,
};
+static struct gpiod_lookup_table tosa_mci_gpio_table = {
+ .dev_id = "pxa2xx-mci.0",
+ .table = {
+ GPIO_LOOKUP("gpio-pxa", TOSA_GPIO_nSD_DETECT,
+ "cd", GPIO_ACTIVE_LOW),
+ GPIO_LOOKUP("gpio-pxa", TOSA_GPIO_SD_WP,
+ "wp", GPIO_ACTIVE_LOW),
+ { },
+ },
+};
+
/*
* Irda
*/
@@ -908,6 +918,7 @@ static void __init tosa_init(void)
/* enable batt_fault */
PMCR = 0x01;
+ gpiod_add_lookup_table(&tosa_mci_gpio_table);
pxa_set_mci_info(&tosa_mci_platform_data);
pxa_set_ficp_info(&tosa_ficp_platform_data);
pxa_set_i2c_info(NULL);
@@ -355,8 +355,6 @@ static struct pxamci_platform_data trizeps4_mci_platform_data = {
.exit = trizeps4_mci_exit,
.get_ro = NULL, /* write-protection not supported */
.setpower = NULL, /* power-switching not supported */
- .gpio_card_detect = -1,
- .gpio_card_ro = -1,
.gpio_power = -1,
};
@@ -17,6 +17,7 @@
#include <linux/input.h>
#include <linux/leds.h>
#include <linux/gpio.h>
+#include <linux/gpio/machine.h>
#include <linux/usb/gpio_vbus.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
@@ -241,13 +242,23 @@ static void __init vpac270_onenand_init(void) {}
static struct pxamci_platform_data vpac270_mci_platform_data = {
.ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
.gpio_power = -1,
- .gpio_card_detect = GPIO53_VPAC270_SD_DETECT_N,
- .gpio_card_ro = GPIO52_VPAC270_SD_READONLY,
.detect_delay_ms = 200,
};
+static struct gpiod_lookup_table vpac270_mci_gpio_table = {
+ .dev_id = "pxa2xx-mci.0",
+ .table = {
+ GPIO_LOOKUP("gpio-pxa", GPIO53_VPAC270_SD_DETECT_N,
+ "cd", GPIO_ACTIVE_LOW),
+ GPIO_LOOKUP("gpio-pxa", GPIO52_VPAC270_SD_READONLY,
+ "wp", GPIO_ACTIVE_LOW),
+ { },
+ },
+};
+
static void __init vpac270_mmc_init(void)
{
+ gpiod_add_lookup_table(&vpac270_mci_gpio_table);
pxa_set_mci_info(&vpac270_mci_platform_data);
}
#else
@@ -27,6 +27,7 @@
#include <linux/power_supply.h>
#include <linux/mtd/physmap.h>
#include <linux/gpio.h>
+#include <linux/gpio/machine.h>
#include <linux/gpio_keys.h>
#include <linux/delay.h>
#include <linux/regulator/machine.h>
@@ -290,14 +291,22 @@ static inline void z2_lcd_init(void) {}
#if defined(CONFIG_MMC_PXA) || defined(CONFIG_MMC_PXA_MODULE)
static struct pxamci_platform_data z2_mci_platform_data = {
.ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
- .gpio_card_detect = GPIO96_ZIPITZ2_SD_DETECT,
.gpio_power = -1,
- .gpio_card_ro = -1,
.detect_delay_ms = 200,
};
+static struct gpiod_lookup_table z2_mci_gpio_table = {
+ .dev_id = "pxa2xx-mci.0",
+ .table = {
+ GPIO_LOOKUP("gpio-pxa", GPIO96_ZIPITZ2_SD_DETECT,
+ "cd", GPIO_ACTIVE_LOW),
+ { },
+ },
+};
+
static void __init z2_mmc_init(void)
{
+ gpiod_add_lookup_table(&z2_mci_gpio_table);
pxa_set_mci_info(&z2_mci_platform_data);
}
#else
@@ -663,12 +663,21 @@ static struct pxafb_mach_info zeus_fb_info = {
static struct pxamci_platform_data zeus_mci_platform_data = {
.ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
.detect_delay_ms = 250,
- .gpio_card_detect = ZEUS_MMC_CD_GPIO,
- .gpio_card_ro = ZEUS_MMC_WP_GPIO,
.gpio_card_ro_invert = 1,
.gpio_power = -1
};
+static struct gpiod_lookup_table zeus_mci_gpio_table = {
+ .dev_id = "pxa2xx-mci.0",
+ .table = {
+ GPIO_LOOKUP("gpio-pxa", ZEUS_MMC_CD_GPIO,
+ "cd", GPIO_ACTIVE_LOW),
+ GPIO_LOOKUP("gpio-pxa", ZEUS_MMC_WP_GPIO,
+ "wp", GPIO_ACTIVE_HIGH),
+ { },
+ },
+};
+
/*
* USB Device Controller
*/
@@ -883,6 +892,7 @@ static void __init zeus_init(void)
else
pxa_set_fb_info(NULL, &zeus_fb_info);
+ gpiod_add_lookup_table(&zeus_mci_gpio_table);
pxa_set_mci_info(&zeus_mci_platform_data);
pxa_set_udc_info(&zeus_udc_info);
pxa_set_ac97_info(&zeus_ac97_info);
@@ -19,7 +19,7 @@
#include <linux/leds.h>
#include <linux/init.h>
#include <linux/platform_device.h>
-#include <linux/gpio.h>
+#include <linux/gpio/machine.h>
#include <linux/pwm.h>
#include <linux/pwm_backlight.h>
#include <linux/smc91x.h>
@@ -227,33 +227,58 @@ static inline void zylonite_init_lcd(void) {}
static struct pxamci_platform_data zylonite_mci_platform_data = {
.detect_delay_ms= 200,
.ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
- .gpio_card_detect = EXT_GPIO(0),
- .gpio_card_ro = EXT_GPIO(2),
.gpio_power = -1,
};
+static struct gpiod_lookup_table zylonite_mci_gpio_table = {
+ .dev_id = "pxa2xx-mci.0",
+ .table = {
+ GPIO_LOOKUP("pca9539", 0, "cd", GPIO_ACTIVE_LOW),
+ GPIO_LOOKUP("pca9539", 2, "wp", GPIO_ACTIVE_LOW),
+ { },
+ },
+};
+
static struct pxamci_platform_data zylonite_mci2_platform_data = {
.detect_delay_ms= 200,
.ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
- .gpio_card_detect = EXT_GPIO(1),
- .gpio_card_ro = EXT_GPIO(3),
.gpio_power = -1,
};
+static struct gpiod_lookup_table zylonite_mci2_gpio_table = {
+ .dev_id = "pxa2xx-mci.1",
+ .table = {
+ GPIO_LOOKUP("pca9539", 1, "cd", GPIO_ACTIVE_LOW),
+ GPIO_LOOKUP("pca9539", 3, "wp", GPIO_ACTIVE_LOW),
+ { },
+ },
+};
+
static struct pxamci_platform_data zylonite_mci3_platform_data = {
.detect_delay_ms= 200,
.ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
- .gpio_card_detect = EXT_GPIO(30),
- .gpio_card_ro = EXT_GPIO(31),
.gpio_power = -1,
};
+static struct gpiod_lookup_table zylonite_mci3_gpio_table = {
+ .dev_id = "pxa2xx-mci.2",
+ .table = {
+ GPIO_LOOKUP("pca9539", 30, "cd", GPIO_ACTIVE_LOW),
+ GPIO_LOOKUP("pca9539", 31, "wp", GPIO_ACTIVE_LOW),
+ { },
+ },
+};
+
static void __init zylonite_init_mmc(void)
{
+ gpiod_add_lookup_table(&zylonite_mci_gpio_table);
pxa_set_mci_info(&zylonite_mci_platform_data);
+ gpiod_add_lookup_table(&zylonite_mci2_gpio_table);
pxa3xx_set_mci2_info(&zylonite_mci2_platform_data);
- if (cpu_is_pxa310())
+ if (cpu_is_pxa310()) {
+ gpiod_add_lookup_table(&zylonite_mci3_gpio_table);
pxa3xx_set_mci3_info(&zylonite_mci3_platform_data);
+ }
}
#else
static inline void zylonite_init_mmc(void) {}
@@ -33,7 +33,6 @@
#include <linux/gpio.h>
#include <linux/gfp.h>
#include <linux/of.h>
-#include <linux/of_gpio.h>
#include <linux/of_device.h>
#include <asm/sizes.h>
@@ -63,6 +62,7 @@ struct pxamci_host {
unsigned int imask;
unsigned int power_mode;
unsigned long detect_delay_ms;
+ bool use_ro_gpio;
struct pxamci_platform_data *pdata;
struct mmc_request *mrq;
@@ -432,7 +432,7 @@ static int pxamci_get_ro(struct mmc_host *mmc)
{
struct pxamci_host *host = mmc_priv(mmc);
- if (host->pdata && gpio_is_valid(host->pdata->gpio_card_ro))
+ if (host->use_ro_gpio)
return mmc_gpio_get_ro(mmc);
if (host->pdata && host->pdata->get_ro)
return !!host->pdata->get_ro(mmc_dev(mmc));
@@ -730,8 +730,6 @@ static int pxamci_probe(struct platform_device *pdev)
}
if (host->pdata) {
- int gpio_cd = host->pdata->gpio_card_detect;
- int gpio_ro = host->pdata->gpio_card_ro;
int gpio_power = host->pdata->gpio_power;
host->detect_delay_ms = host->pdata->detect_delay_ms;
@@ -749,33 +747,30 @@ static int pxamci_probe(struct platform_device *pdev)
host->pdata->gpio_power_invert);
}
- if (gpio_is_valid(gpio_ro)) {
- ret = mmc_gpio_request_ro(mmc, gpio_ro);
- if (ret) {
- dev_err(dev,
- "Failed requesting gpio_ro %d\n",
- gpio_ro);
- goto out;
- } else {
- mmc->caps2 |= host->pdata->gpio_card_ro_invert ?
- 0 : MMC_CAP2_RO_ACTIVE_HIGH;
- }
+ /* FIXME: should we pass detection delay to debounce? */
+ ret = mmc_gpiod_request_cd(mmc, "cd", 0, false, 0, NULL);
+ if (ret && ret != -ENOENT) {
+ dev_err(dev, "Failed requesting gpio_cd\n");
+ goto out;
}
- if (gpio_is_valid(gpio_cd))
- ret = mmc_gpio_request_cd(mmc, gpio_cd, 0);
- if (ret) {
- dev_err(dev, "Failed requesting gpio_cd %d\n",
- gpio_cd);
+ ret = mmc_gpiod_request_ro(mmc, "wp", 0, false, 0, NULL);
+ if (ret && ret != -ENOENT) {
+ dev_err(dev, "Failed requesting gpio_ro\n");
goto out;
}
+ if (!ret) {
+ host->use_ro_gpio = true;
+ mmc->caps2 |= host->pdata->gpio_card_ro_invert ?
+ 0 : MMC_CAP2_RO_ACTIVE_HIGH;
+ }
if (host->pdata->init)
host->pdata->init(dev, pxamci_detect_irq, mmc);
if (gpio_is_valid(gpio_power) && host->pdata->setpower)
dev_warn(dev, "gpio_power and setpower() both defined\n");
- if (gpio_is_valid(gpio_ro) && host->pdata->get_ro)
+ if (host->use_ro_gpio && host->pdata->get_ro)
dev_warn(dev, "gpio_ro and get_ro() both defined\n");
}
@@ -15,8 +15,6 @@ struct pxamci_platform_data {
int (*get_ro)(struct device *);
int (*setpower)(struct device *, unsigned int);
void (*exit)(struct device *, void *);
- int gpio_card_detect; /* gpio detecting card insertion */
- int gpio_card_ro; /* gpio detecting read only toggle */
bool gpio_card_ro_invert; /* gpio ro is inverted */
int gpio_power; /* gpio powering up MMC bus */
bool gpio_power_invert; /* gpio power is inverted */
Simplify things by making the PXA MCI driver just use slot GPIO with descriptors instead of passing around the global GPIO numbers that we want to get rid of. This involves augmenting more or less every PXA boardfile, associating each card detect or write protect line with the right GPIO chip or GPIO expander. As we are no longer checking for global GPIO numbers we avoid having to fill them in at all in the platform data including the kludge of setting the GPIO to -1 when we don't have either signal. We just look for the slot GPIO descriptor for CD and WP and if we find it we use it. We take care of correctly specifying the edge sensitivity of the GPIO lines (active low or active high) so we can later on use this flag even though the MMC slot GPIO code uses the *raw accessors and rely on the caps2 flags MMC_CAP2_CD_ACTIVE_HIGH and MMC_CAP2_RO_ACTIVE_HIGH for polarity inversion semantics as of now. Cc: Daniel Mack <daniel@zonque.org> Cc: Robert Jarzmik <robert.jarzmik@free.fr> Cc: Bartosz Golaszewski <brgl@bgdev.pl> Cc: Andrea Adami <andrea.adami@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> --- arch/arm/mach-pxa/balloon3.c | 2 -- arch/arm/mach-pxa/cm-x270.c | 18 ++++++---- arch/arm/mach-pxa/cm-x300.c | 21 +++++++----- arch/arm/mach-pxa/colibri-evalboard.c | 40 +++++++++++++++++----- arch/arm/mach-pxa/colibri-pxa270-income.c | 18 +++++++--- arch/arm/mach-pxa/corgi.c | 16 +++++++-- arch/arm/mach-pxa/csb726.c | 18 ++++++++-- arch/arm/mach-pxa/em-x270.c | 33 +++++++----------- arch/arm/mach-pxa/gumstix.c | 2 -- arch/arm/mach-pxa/idp.c | 2 -- arch/arm/mach-pxa/littleton.c | 16 ++++++--- arch/arm/mach-pxa/lubbock.c | 2 -- arch/arm/mach-pxa/magician.c | 15 +++++++-- arch/arm/mach-pxa/mainstone.c | 2 -- arch/arm/mach-pxa/mioa701.c | 15 +++++++-- arch/arm/mach-pxa/mxm8x10.c | 16 +++++++-- arch/arm/mach-pxa/palm27x.c | 8 ++--- arch/arm/mach-pxa/palm27x.h | 12 ++++--- arch/arm/mach-pxa/palmld.c | 15 +++++++-- arch/arm/mach-pxa/palmt5.c | 15 +++++++-- arch/arm/mach-pxa/palmtc.c | 16 +++++++-- arch/arm/mach-pxa/palmte2.c | 15 +++++++-- arch/arm/mach-pxa/palmtreo.c | 29 +++++++++++++--- arch/arm/mach-pxa/palmtx.c | 15 +++++++-- arch/arm/mach-pxa/palmz72.c | 15 +++++++-- arch/arm/mach-pxa/pcm990-baseboard.c | 2 -- arch/arm/mach-pxa/poodle.c | 14 ++++++-- arch/arm/mach-pxa/raumfeld.c | 2 -- arch/arm/mach-pxa/spitz.c | 15 +++++++-- arch/arm/mach-pxa/stargate2.c | 2 -- arch/arm/mach-pxa/tosa.c | 15 +++++++-- arch/arm/mach-pxa/trizeps4.c | 2 -- arch/arm/mach-pxa/vpac270.c | 15 +++++++-- arch/arm/mach-pxa/z2.c | 13 +++++-- arch/arm/mach-pxa/zeus.c | 14 ++++++-- arch/arm/mach-pxa/zylonite.c | 41 ++++++++++++++++++----- drivers/mmc/host/pxamci.c | 37 +++++++++----------- include/linux/platform_data/mmc-pxamci.h | 2 -- 38 files changed, 397 insertions(+), 153 deletions(-)