@@ -929,6 +929,11 @@ static void sdhci_set_transfer_irqs(struct sdhci_host *host)
else
host->ier = (host->ier & ~dma_irqs) | pio_irqs;
+ if (host->flags & (SDHCI_AUTO_CMD23 | SDHCI_AUTO_CMD12))
+ host->ier |= SDHCI_INT_AUTO_CMD_ERR;
+ else
+ host->ier &= ~SDHCI_INT_AUTO_CMD_ERR;
+
sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
}
@@ -2749,6 +2754,21 @@ static void sdhci_timeout_data_timer(struct timer_list *t)
static void sdhci_cmd_irq(struct sdhci_host *host, u32 intmask, u32 *intmask_p)
{
+ /* Handle auto-CMD12 error */
+ if (intmask & SDHCI_INT_AUTO_CMD_ERR && host->data_cmd) {
+ struct mmc_request *mrq = host->data_cmd->mrq;
+ u16 auto_cmd_status = sdhci_readw(host, SDHCI_AUTO_CMD_STATUS);
+ int data_err_bit = (auto_cmd_status & SDHCI_AUTO_CMD_TIMEOUT) ?
+ SDHCI_INT_DATA_TIMEOUT :
+ SDHCI_INT_DATA_CRC;
+
+ /* Treat auto-CMD12 error the same as data error */
+ if (!mrq->sbc && (host->flags & SDHCI_AUTO_CMD12)) {
+ *intmask_p |= data_err_bit;
+ return;
+ }
+ }
+
if (!host->cmd) {
/*
* SDHCI recovers from errors by resetting the cmd and data
@@ -2783,6 +2803,21 @@ static void sdhci_cmd_irq(struct sdhci_host *host, u32 intmask, u32 *intmask_p)
return;
}
+ /* Handle auto-CMD23 error */
+ if (intmask & SDHCI_INT_AUTO_CMD_ERR) {
+ struct mmc_request *mrq = host->cmd->mrq;
+ u16 auto_cmd_status = sdhci_readw(host, SDHCI_AUTO_CMD_STATUS);
+ int err = (auto_cmd_status & SDHCI_AUTO_CMD_TIMEOUT) ?
+ -ETIMEDOUT :
+ -EILSEQ;
+
+ if (mrq->sbc && (host->flags & SDHCI_AUTO_CMD23)) {
+ mrq->sbc->error = err;
+ sdhci_finish_mrq(host, mrq);
+ return;
+ }
+ }
+
if (intmask & SDHCI_INT_RESPONSE)
sdhci_finish_command(host);
}
@@ -153,7 +153,8 @@
#define SDHCI_INT_ERROR_MASK 0xFFFF8000
#define SDHCI_INT_CMD_MASK (SDHCI_INT_RESPONSE | SDHCI_INT_TIMEOUT | \
- SDHCI_INT_CRC | SDHCI_INT_END_BIT | SDHCI_INT_INDEX)
+ SDHCI_INT_CRC | SDHCI_INT_END_BIT | SDHCI_INT_INDEX | \
+ SDHCI_INT_AUTO_CMD_ERR)
#define SDHCI_INT_DATA_MASK (SDHCI_INT_DATA_END | SDHCI_INT_DMA_END | \
SDHCI_INT_DATA_AVAIL | SDHCI_INT_SPACE_AVAIL | \
SDHCI_INT_DATA_TIMEOUT | SDHCI_INT_DATA_CRC | \
@@ -169,6 +170,10 @@
#define SDHCI_CQE_INT_MASK (SDHCI_CQE_INT_ERR_MASK | SDHCI_INT_CQE)
#define SDHCI_AUTO_CMD_STATUS 0x3C
+#define SDHCI_AUTO_CMD_TIMEOUT 0x00000002
+#define SDHCI_AUTO_CMD_CRC 0x00000004
+#define SDHCI_AUTO_CMD_END_BIT 0x00000008
+#define SDHCI_AUTO_CMD_INDEX 0x00000010
#define SDHCI_HOST_CONTROL2 0x3E
#define SDHCI_CTRL_UHS_MASK 0x0007
If the host controller supports auto-commands then enable the auto-command error interrupt and handle it. In the case of auto-CMD23, the error is treated the same as manual CMD23 error. In the case of auto-CMD12, commands-during-transfer are not permitted, so the error handling is treated the same as a data error. Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> --- drivers/mmc/host/sdhci.c | 35 +++++++++++++++++++++++++++++++++++ drivers/mmc/host/sdhci.h | 7 ++++++- 2 files changed, 41 insertions(+), 1 deletion(-)