diff mbox series

[v4,3/4] mmc: sdhci-brcmstb: Add BCM2712 support

Message ID 4e8fc54e87447bae7db58636a1c87e5d8baeb012.1716899600.git.andrea.porta@suse.com (mailing list archive)
State New
Headers show
Series Add minimal boot support for Raspberry Pi 5 | expand

Commit Message

Andrea della Porta May 28, 2024, 1:32 p.m. UTC 
Broadcom BCM2712 SoC has an SDHCI card controller using the SDIO CFG
register block present on other STB chips. Add support for BCM2712
SD capabilities of this chipset.
The silicon is SD Express capable but this driver port does not currently
include that feature yet.
Based on downstream driver by raspberry foundation maintained kernel.

Signed-off-by: Andrea della Porta <andrea.porta@suse.com>
---
 drivers/mmc/host/sdhci-brcmstb.c | 60 ++++++++++++++++++++++++++++++++
 1 file changed, 60 insertions(+)

Comments

Stefan Wahren May 28, 2024, 2:16 p.m. UTC | #1 
Am 28.05.24 um 15:32 schrieb Andrea della Porta:
> Broadcom BCM2712 SoC has an SDHCI card controller using the SDIO CFG
> register block present on other STB chips. Add support for BCM2712
> SD capabilities of this chipset.
> The silicon is SD Express capable but this driver port does not currently
> include that feature yet.
> Based on downstream driver by raspberry foundation maintained kernel.
>
> Signed-off-by: Andrea della Porta <andrea.porta@suse.com>
Reviewed-by: Stefan Wahren <wahrenst@gmx.net>
Adrian Hunter May 29, 2024, 9:25 a.m. UTC | #2 
On 28/05/24 16:32, Andrea della Porta wrote:
> Broadcom BCM2712 SoC has an SDHCI card controller using the SDIO CFG
> register block present on other STB chips. Add support for BCM2712
> SD capabilities of this chipset.
> The silicon is SD Express capable but this driver port does not currently
> include that feature yet.
> Based on downstream driver by raspberry foundation maintained kernel.
> 
> Signed-off-by: Andrea della Porta <andrea.porta@suse.com>

One minor comment below, otherwise:

Acked-by: Adrian Hunter <adrian.hunter@intel.com>


Also, unrelated to this patch, the driver has this code which looks
like it would have an issue if there were 2 devices of the same
type but only 1 had supports-cqe, because the ops would be shared
they would both try to use sdhci_brcmstb_cqhci_irq().

	if (device_property_read_bool(&pdev->dev, "supports-cqe")) {
		priv->flags |= BRCMSTB_PRIV_FLAGS_HAS_CQE;
		match_priv->ops->irq = sdhci_brcmstb_cqhci_irq;
	}

> ---
>  drivers/mmc/host/sdhci-brcmstb.c | 60 ++++++++++++++++++++++++++++++++
>  1 file changed, 60 insertions(+)
> 
> diff --git a/drivers/mmc/host/sdhci-brcmstb.c b/drivers/mmc/host/sdhci-brcmstb.c
> index 9053526fa212..0d9c42d41376 100644
> --- a/drivers/mmc/host/sdhci-brcmstb.c
> +++ b/drivers/mmc/host/sdhci-brcmstb.c
> @@ -30,6 +30,21 @@
>  
>  #define SDHCI_ARASAN_CQE_BASE_ADDR		0x200
>  
> +#define SDIO_CFG_CQ_CAPABILITY			0x4c
> +#define SDIO_CFG_CQ_CAPABILITY_FMUL		GENMASK(13, 12)
> +
> +#define SDIO_CFG_CTRL				0x0
> +#define SDIO_CFG_CTRL_SDCD_N_TEST_EN		BIT(31)
> +#define SDIO_CFG_CTRL_SDCD_N_TEST_LEV		BIT(30)
> +
> +#define SDIO_CFG_MAX_50MHZ_MODE			0x1ac
> +#define SDIO_CFG_MAX_50MHZ_MODE_STRAP_OVERRIDE	BIT(31)
> +#define SDIO_CFG_MAX_50MHZ_MODE_ENABLE		BIT(0)
> +
> +#define MMC_CAP_HSE_MASK	(MMC_CAP2_HSX00_1_2V | MMC_CAP2_HSX00_1_8V)
> +/* Select all SD UHS type I SDR speed above 50MB/s */
> +#define MMC_CAP_UHS_I_SDR_MASK	(MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR104)
> +
>  struct sdhci_brcmstb_priv {
>  	void __iomem *cfg_regs;
>  	unsigned int flags;
> @@ -38,6 +53,7 @@ struct sdhci_brcmstb_priv {
>  };
>  
>  struct brcmstb_match_priv {
> +	void (*cfginit)(struct sdhci_host *host);
>  	void (*hs400es)(struct mmc_host *mmc, struct mmc_ios *ios);
>  	struct sdhci_ops *ops;
>  	const unsigned int flags;
> @@ -168,6 +184,33 @@ static void sdhci_brcmstb_set_uhs_signaling(struct sdhci_host *host,
>  	sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
>  }
>  
> +static void sdhci_brcmstb_cfginit_2712(struct sdhci_host *host)
> +{
> +	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> +	struct sdhci_brcmstb_priv *brcmstb_priv = sdhci_pltfm_priv(pltfm_host);
> +	u32 reg, base_clk_mhz;

drivers/mmc/host/sdhci-brcmstb.c: In function ‘sdhci_brcmstb_cfginit_2712’:
drivers/mmc/host/sdhci-brcmstb.c:191:18: error: unused variable ‘base_clk_mhz’ [-Werror=unused-variable]
  191 |         u32 reg, base_clk_mhz;
      |                  ^~~~~~~~~~~~


> +
> +	/*
> +	 * If we support a speed that requires tuning,
> +	 * then select the delay line PHY as the clock source.
> +	 */
> +	if ((host->mmc->caps & MMC_CAP_UHS_I_SDR_MASK) || (host->mmc->caps2 & MMC_CAP_HSE_MASK)) {
> +		reg = readl(brcmstb_priv->cfg_regs + SDIO_CFG_MAX_50MHZ_MODE);
> +		reg &= ~SDIO_CFG_MAX_50MHZ_MODE_ENABLE;
> +		reg |= SDIO_CFG_MAX_50MHZ_MODE_STRAP_OVERRIDE;
> +		writel(reg, brcmstb_priv->cfg_regs + SDIO_CFG_MAX_50MHZ_MODE);
> +	}
> +
> +	if ((host->mmc->caps & MMC_CAP_NONREMOVABLE) ||
> +	    (host->mmc->caps & MMC_CAP_NEEDS_POLL)) {
> +		/* Force presence */
> +		reg = readl(brcmstb_priv->cfg_regs + SDIO_CFG_CTRL);
> +		reg &= ~SDIO_CFG_CTRL_SDCD_N_TEST_LEV;
> +		reg |= SDIO_CFG_CTRL_SDCD_N_TEST_EN;
> +		writel(reg, brcmstb_priv->cfg_regs + SDIO_CFG_CTRL);
> +	}
> +}
> +
>  static void sdhci_brcmstb_dumpregs(struct mmc_host *mmc)
>  {
>  	sdhci_dumpregs(mmc_priv(mmc));
> @@ -200,6 +243,14 @@ static struct sdhci_ops sdhci_brcmstb_ops = {
>  	.set_uhs_signaling = sdhci_set_uhs_signaling,
>  };
>  
> +static struct sdhci_ops sdhci_brcmstb_ops_2712 = {
> +	.set_clock = sdhci_set_clock,
> +	.set_power = sdhci_set_power_and_bus_voltage,
> +	.set_bus_width = sdhci_set_bus_width,
> +	.reset = sdhci_reset,
> +	.set_uhs_signaling = sdhci_set_uhs_signaling,
> +};
> +
>  static struct sdhci_ops sdhci_brcmstb_ops_7216 = {
>  	.set_clock = sdhci_brcmstb_set_clock,
>  	.set_bus_width = sdhci_set_bus_width,
> @@ -214,6 +265,11 @@ static struct sdhci_ops sdhci_brcmstb_ops_74165b0 = {
>  	.set_uhs_signaling = sdhci_brcmstb_set_uhs_signaling,
>  };
>  
> +static const struct brcmstb_match_priv match_priv_2712 = {
> +	.cfginit = sdhci_brcmstb_cfginit_2712,
> +	.ops = &sdhci_brcmstb_ops_2712,
> +};
> +
>  static struct brcmstb_match_priv match_priv_7425 = {
>  	.flags = BRCMSTB_MATCH_FLAGS_NO_64BIT |
>  	BRCMSTB_MATCH_FLAGS_BROKEN_TIMEOUT,
> @@ -238,6 +294,7 @@ static struct brcmstb_match_priv match_priv_74165b0 = {
>  };
>  
>  static const struct of_device_id __maybe_unused sdhci_brcm_of_match[] = {
> +	{ .compatible = "brcm,bcm2712-sdhci", .data = &match_priv_2712 },
>  	{ .compatible = "brcm,bcm7425-sdhci", .data = &match_priv_7425 },
>  	{ .compatible = "brcm,bcm7445-sdhci", .data = &match_priv_7445 },
>  	{ .compatible = "brcm,bcm7216-sdhci", .data = &match_priv_7216 },
> @@ -370,6 +427,9 @@ static int sdhci_brcmstb_probe(struct platform_device *pdev)
>  	    (host->mmc->caps2 & MMC_CAP2_HS400_ES))
>  		host->mmc_host_ops.hs400_enhanced_strobe = match_priv->hs400es;
>  
> +	if (match_priv->cfginit)
> +		match_priv->cfginit(host);
> +
>  	/*
>  	 * Supply the existing CAPS, but clear the UHS modes. This
>  	 * will allow these modes to be specified by device tree
diff mbox series

Patch

diff --git a/drivers/mmc/host/sdhci-brcmstb.c b/drivers/mmc/host/sdhci-brcmstb.c
index 9053526fa212..0d9c42d41376 100644
--- a/drivers/mmc/host/sdhci-brcmstb.c
+++ b/drivers/mmc/host/sdhci-brcmstb.c
@@ -30,6 +30,21 @@ 
 
 #define SDHCI_ARASAN_CQE_BASE_ADDR		0x200
 
+#define SDIO_CFG_CQ_CAPABILITY			0x4c
+#define SDIO_CFG_CQ_CAPABILITY_FMUL		GENMASK(13, 12)
+
+#define SDIO_CFG_CTRL				0x0
+#define SDIO_CFG_CTRL_SDCD_N_TEST_EN		BIT(31)
+#define SDIO_CFG_CTRL_SDCD_N_TEST_LEV		BIT(30)
+
+#define SDIO_CFG_MAX_50MHZ_MODE			0x1ac
+#define SDIO_CFG_MAX_50MHZ_MODE_STRAP_OVERRIDE	BIT(31)
+#define SDIO_CFG_MAX_50MHZ_MODE_ENABLE		BIT(0)
+
+#define MMC_CAP_HSE_MASK	(MMC_CAP2_HSX00_1_2V | MMC_CAP2_HSX00_1_8V)
+/* Select all SD UHS type I SDR speed above 50MB/s */
+#define MMC_CAP_UHS_I_SDR_MASK	(MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR104)
+
 struct sdhci_brcmstb_priv {
 	void __iomem *cfg_regs;
 	unsigned int flags;
@@ -38,6 +53,7 @@  struct sdhci_brcmstb_priv {
 };
 
 struct brcmstb_match_priv {
+	void (*cfginit)(struct sdhci_host *host);
 	void (*hs400es)(struct mmc_host *mmc, struct mmc_ios *ios);
 	struct sdhci_ops *ops;
 	const unsigned int flags;
@@ -168,6 +184,33 @@  static void sdhci_brcmstb_set_uhs_signaling(struct sdhci_host *host,
 	sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
 }
 
+static void sdhci_brcmstb_cfginit_2712(struct sdhci_host *host)
+{
+	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+	struct sdhci_brcmstb_priv *brcmstb_priv = sdhci_pltfm_priv(pltfm_host);
+	u32 reg, base_clk_mhz;
+
+	/*
+	 * If we support a speed that requires tuning,
+	 * then select the delay line PHY as the clock source.
+	 */
+	if ((host->mmc->caps & MMC_CAP_UHS_I_SDR_MASK) || (host->mmc->caps2 & MMC_CAP_HSE_MASK)) {
+		reg = readl(brcmstb_priv->cfg_regs + SDIO_CFG_MAX_50MHZ_MODE);
+		reg &= ~SDIO_CFG_MAX_50MHZ_MODE_ENABLE;
+		reg |= SDIO_CFG_MAX_50MHZ_MODE_STRAP_OVERRIDE;
+		writel(reg, brcmstb_priv->cfg_regs + SDIO_CFG_MAX_50MHZ_MODE);
+	}
+
+	if ((host->mmc->caps & MMC_CAP_NONREMOVABLE) ||
+	    (host->mmc->caps & MMC_CAP_NEEDS_POLL)) {
+		/* Force presence */
+		reg = readl(brcmstb_priv->cfg_regs + SDIO_CFG_CTRL);
+		reg &= ~SDIO_CFG_CTRL_SDCD_N_TEST_LEV;
+		reg |= SDIO_CFG_CTRL_SDCD_N_TEST_EN;
+		writel(reg, brcmstb_priv->cfg_regs + SDIO_CFG_CTRL);
+	}
+}
+
 static void sdhci_brcmstb_dumpregs(struct mmc_host *mmc)
 {
 	sdhci_dumpregs(mmc_priv(mmc));
@@ -200,6 +243,14 @@  static struct sdhci_ops sdhci_brcmstb_ops = {
 	.set_uhs_signaling = sdhci_set_uhs_signaling,
 };
 
+static struct sdhci_ops sdhci_brcmstb_ops_2712 = {
+	.set_clock = sdhci_set_clock,
+	.set_power = sdhci_set_power_and_bus_voltage,
+	.set_bus_width = sdhci_set_bus_width,
+	.reset = sdhci_reset,
+	.set_uhs_signaling = sdhci_set_uhs_signaling,
+};
+
 static struct sdhci_ops sdhci_brcmstb_ops_7216 = {
 	.set_clock = sdhci_brcmstb_set_clock,
 	.set_bus_width = sdhci_set_bus_width,
@@ -214,6 +265,11 @@  static struct sdhci_ops sdhci_brcmstb_ops_74165b0 = {
 	.set_uhs_signaling = sdhci_brcmstb_set_uhs_signaling,
 };
 
+static const struct brcmstb_match_priv match_priv_2712 = {
+	.cfginit = sdhci_brcmstb_cfginit_2712,
+	.ops = &sdhci_brcmstb_ops_2712,
+};
+
 static struct brcmstb_match_priv match_priv_7425 = {
 	.flags = BRCMSTB_MATCH_FLAGS_NO_64BIT |
 	BRCMSTB_MATCH_FLAGS_BROKEN_TIMEOUT,
@@ -238,6 +294,7 @@  static struct brcmstb_match_priv match_priv_74165b0 = {
 };
 
 static const struct of_device_id __maybe_unused sdhci_brcm_of_match[] = {
+	{ .compatible = "brcm,bcm2712-sdhci", .data = &match_priv_2712 },
 	{ .compatible = "brcm,bcm7425-sdhci", .data = &match_priv_7425 },
 	{ .compatible = "brcm,bcm7445-sdhci", .data = &match_priv_7445 },
 	{ .compatible = "brcm,bcm7216-sdhci", .data = &match_priv_7216 },
@@ -370,6 +427,9 @@  static int sdhci_brcmstb_probe(struct platform_device *pdev)
 	    (host->mmc->caps2 & MMC_CAP2_HS400_ES))
 		host->mmc_host_ops.hs400_enhanced_strobe = match_priv->hs400es;
 
+	if (match_priv->cfginit)
+		match_priv->cfginit(host);
+
 	/*
 	 * Supply the existing CAPS, but clear the UHS modes. This
 	 * will allow these modes to be specified by device tree