diff --git a/drivers/bluetooth/Kconfig b/drivers/bluetooth/Kconfig
index de62ccf43df6..bff51d45cdcf 100644
--- a/drivers/bluetooth/Kconfig
+++ b/drivers/bluetooth/Kconfig
@@ -390,6 +390,17 @@ config BT_WILINK
 	  Say Y here to compile support for Texas Instrument's WiLink7 driver
 	  into the kernel or say M to compile it as module (btwilink).
 
+config BT_MTKSDIO
+	tristate "MediaTek HCI SDIO driver"
+	depends on MMC
+	help
+	  MediaTek Bluetooth HCI SDIO driver.
+	  This driver is required if you want to use MediaTek Bluetooth
+	  with SDIO interface.
+
+	  Say Y here to compile support for MediaTek Bluetooth SDIO devices
+	  into the kernel or say M to compile it as module (btmtksdio).
+
 config BT_MTKUART
 	tristate "MediaTek HCI UART driver"
 	depends on SERIAL_DEV_BUS
diff --git a/drivers/bluetooth/Makefile b/drivers/bluetooth/Makefile
index b7e393cfc1e3..34887b9b3a85 100644
--- a/drivers/bluetooth/Makefile
+++ b/drivers/bluetooth/Makefile
@@ -20,6 +20,7 @@ obj-$(CONFIG_BT_ATH3K)		+= ath3k.o
 obj-$(CONFIG_BT_MRVL)		+= btmrvl.o
 obj-$(CONFIG_BT_MRVL_SDIO)	+= btmrvl_sdio.o
 obj-$(CONFIG_BT_WILINK)		+= btwilink.o
+obj-$(CONFIG_BT_MTKSDIO)	+= btmtksdio.o
 obj-$(CONFIG_BT_MTKUART)	+= btmtkuart.o
 obj-$(CONFIG_BT_QCOMSMD)	+= btqcomsmd.o
 obj-$(CONFIG_BT_BCM)		+= btbcm.o
diff --git a/drivers/bluetooth/btmtksdio.c b/drivers/bluetooth/btmtksdio.c
new file mode 100644
index 000000000000..b4b8320f279e
--- /dev/null
+++ b/drivers/bluetooth/btmtksdio.c
@@ -0,0 +1,979 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2019 MediaTek Inc.
+
+/*
+ * Bluetooth support for MediaTek SDIO devices
+ *
+ * This file is written based on btsdio.c and btmtkuart.c.
+ *
+ * Author: Sean Wang <sean.wang@mediatek.com>
+ *
+ */
+
+#include <asm/unaligned.h>
+#include <linux/atomic.h>
+#include <linux/firmware.h>
+#include <linux/init.h>
+#include <linux/iopoll.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/skbuff.h>
+
+#include <linux/mmc/host.h>
+#include <linux/mmc/sdio_ids.h>
+#include <linux/mmc/sdio_func.h>
+
+#include <net/bluetooth/bluetooth.h>
+#include <net/bluetooth/hci_core.h>
+
+#include "h4_recv.h"
+
+#define VERSION "0.1"
+
+#define FIRMWARE_MT7663		"mediatek/mt7663pr2h.bin"
+#define FIRMWARE_MT7668		"mediatek/mt7668pr2h.bin"
+
+struct btmtksdio_data {
+	const char *fwname;
+};
+
+static const struct btmtksdio_data mt7663_data = {
+	.fwname = FIRMWARE_MT7663,
+};
+
+static const struct btmtksdio_data mt7668_data = {
+	.fwname = FIRMWARE_MT7668,
+};
+
+static const struct sdio_device_id btmtksdio_table[] = {
+	{SDIO_DEVICE(SDIO_VENDOR_ID_MEDIATEK, 0x7663),
+	 .driver_data = (kernel_ulong_t)&mt7663_data },
+	{SDIO_DEVICE(SDIO_VENDOR_ID_MEDIATEK, 0x7668),
+	 .driver_data = (kernel_ulong_t)&mt7668_data },
+	{ }	/* Terminating entry */
+};
+
+#define MTK_REG_CHLPCR		0x4	/* W1S */
+#define C_INT_EN_SET		BIT(0)
+#define C_INT_EN_CLR		BIT(1)
+#define C_FW_OWN_REQ_SET	BIT(8)
+#define C_FW_OWN_REQ_CLR	BIT(9)
+
+#define MTK_REG_CSDIOCSR	0x8
+#define SDIO_RE_INIT_EN		BIT(0)
+#define SDIO_INT_CTL		BIT(2)
+
+#define MTK_REG_CHCR		0xc
+#define C_INT_CLR_CTRL		BIT(1)
+
+/* CHISR have the same bits field definition with CHIER */
+#define MTK_REG_CHISR		0x10
+#define MTK_REG_CHIER		0x14
+#define FW_OWN_BACK_INT		BIT(0)
+#define RX_DONE_INT		BIT(1)
+#define TX_EMPTY		BIT(2)
+#define TX_FIFO_OVERFLOW	BIT(8)
+#define RX_PKT_LEN		GENMASK(31, 16)
+
+#define MTK_REG_CTDR		0x18
+
+#define MTK_REG_CRDR		0x1c
+
+#define MTK_SDIO_BLOCK_SIZE	256
+
+#define BTMTKSDIO_TX_WAIT_VND_EVT	1
+
+enum {
+	MTK_WMT_PATCH_DWNLD = 0x1,
+	MTK_WMT_TEST = 0x2,
+	MTK_WMT_WAKEUP = 0x3,
+	MTK_WMT_HIF = 0x4,
+	MTK_WMT_FUNC_CTRL = 0x6,
+	MTK_WMT_RST = 0x7,
+	MTK_WMT_SEMAPHORE = 0x17,
+};
+
+enum {
+	BTMTK_WMT_INVALID,
+	BTMTK_WMT_PATCH_UNDONE,
+	BTMTK_WMT_PATCH_DONE,
+	BTMTK_WMT_ON_UNDONE,
+	BTMTK_WMT_ON_DONE,
+	BTMTK_WMT_ON_PROGRESS,
+};
+
+struct mtkbtsdio_hdr {
+	__le16	len;
+	__le16	reserved;
+	u8	bt_type;
+} __packed;
+
+struct mtk_wmt_hdr {
+	u8	dir;
+	u8	op;
+	__le16	dlen;
+	u8	flag;
+} __packed;
+
+struct mtk_hci_wmt_cmd {
+	struct mtk_wmt_hdr hdr;
+	u8 data[256];
+} __packed;
+
+struct btmtk_hci_wmt_evt {
+	struct hci_event_hdr hhdr;
+	struct mtk_wmt_hdr whdr;
+} __packed;
+
+struct btmtk_hci_wmt_evt_funcc {
+	struct btmtk_hci_wmt_evt hwhdr;
+	__be16 status;
+} __packed;
+
+struct btmtk_tci_sleep {
+	u8 mode;
+	__le16 duration;
+	__le16 host_duration;
+	u8 host_wakeup_pin;
+	u8 time_compensation;
+} __packed;
+
+struct btmtk_hci_wmt_params {
+	u8 op;
+	u8 flag;
+	u16 dlen;
+	const void *data;
+	u32 *status;
+};
+
+struct btmtksdio_dev {
+	struct hci_dev *hdev;
+	struct sdio_func *func;
+
+	struct work_struct tx_work;
+	unsigned long tx_state;
+	struct sk_buff_head txq;
+
+	struct sk_buff *evt_skb;
+
+	const struct btmtksdio_data *data;
+};
+
+static int mtk_hci_wmt_sync(struct hci_dev *hdev,
+			    struct btmtk_hci_wmt_params *wmt_params)
+{
+	struct btmtksdio_dev *bdev = hci_get_drvdata(hdev);
+	struct btmtk_hci_wmt_evt_funcc *wmt_evt_funcc;
+	u32 hlen, status = BTMTK_WMT_INVALID;
+	struct btmtk_hci_wmt_evt *wmt_evt;
+	struct mtk_hci_wmt_cmd wc;
+	struct mtk_wmt_hdr *hdr;
+	int err;
+
+	hlen = sizeof(*hdr) + wmt_params->dlen;
+	if (hlen > 255)
+		return -EINVAL;
+
+	hdr = (struct mtk_wmt_hdr *)&wc;
+	hdr->dir = 1;
+	hdr->op = wmt_params->op;
+	hdr->dlen = cpu_to_le16(wmt_params->dlen + 1);
+	hdr->flag = wmt_params->flag;
+	memcpy(wc.data, wmt_params->data, wmt_params->dlen);
+
+	set_bit(BTMTKSDIO_TX_WAIT_VND_EVT, &bdev->tx_state);
+
+	err = __hci_cmd_send(hdev, 0xfc6f, hlen, &wc);
+	if (err < 0) {
+		clear_bit(BTMTKSDIO_TX_WAIT_VND_EVT, &bdev->tx_state);
+		return err;
+	}
+
+	/* The vendor specific WMT commands are all answered by a vendor
+	 * specific event and will not have the Command Status or Command
+	 * Complete as with usual HCI command flow control.
+	 *
+	 * After sending the command, wait for BTMTKSDIO_TX_WAIT_VND_EVT
+	 * state to be cleared. The driver specific event receive routine
+	 * will clear that state and with that indicate completion of the
+	 * WMT command.
+	 */
+	err = wait_on_bit_timeout(&bdev->tx_state, BTMTKSDIO_TX_WAIT_VND_EVT,
+				  TASK_INTERRUPTIBLE, HCI_INIT_TIMEOUT);
+	if (err == -EINTR) {
+		bt_dev_err(hdev, "Execution of wmt command interrupted");
+		clear_bit(BTMTKSDIO_TX_WAIT_VND_EVT, &bdev->tx_state);
+		return err;
+	}
+
+	if (err) {
+		bt_dev_err(hdev, "Execution of wmt command timed out");
+		clear_bit(BTMTKSDIO_TX_WAIT_VND_EVT, &bdev->tx_state);
+		return -ETIMEDOUT;
+	}
+
+	/* Parse and handle the return WMT event */
+	wmt_evt = (struct btmtk_hci_wmt_evt *)bdev->evt_skb->data;
+	if (wmt_evt->whdr.op != hdr->op) {
+		bt_dev_err(hdev, "Wrong op received %d expected %d",
+			   wmt_evt->whdr.op, hdr->op);
+		err = -EIO;
+		goto err_free_skb;
+	}
+
+	switch (wmt_evt->whdr.op) {
+	case MTK_WMT_SEMAPHORE:
+		if (wmt_evt->whdr.flag == 2)
+			status = BTMTK_WMT_PATCH_UNDONE;
+		else
+			status = BTMTK_WMT_PATCH_DONE;
+		break;
+	case MTK_WMT_FUNC_CTRL:
+		wmt_evt_funcc = (struct btmtk_hci_wmt_evt_funcc *)wmt_evt;
+		if (be16_to_cpu(wmt_evt_funcc->status) == 0x404)
+			status = BTMTK_WMT_ON_DONE;
+		else if (be16_to_cpu(wmt_evt_funcc->status) == 0x420)
+			status = BTMTK_WMT_ON_PROGRESS;
+		else
+			status = BTMTK_WMT_ON_UNDONE;
+		break;
+	}
+
+	if (wmt_params->status)
+		*wmt_params->status = status;
+
+err_free_skb:
+	kfree_skb(bdev->evt_skb);
+	bdev->evt_skb = NULL;
+
+	return err;
+}
+
+static int btmtksdio_tx_packet(struct btmtksdio_dev *bdev,
+			       struct sk_buff *skb)
+{
+	struct mtkbtsdio_hdr *sdio_hdr;
+	int err;
+
+	/* Make sure that there are enough rooms for SDIO header */
+	if (unlikely(skb_headroom(skb) < sizeof(*sdio_hdr))) {
+		err = pskb_expand_head(skb, sizeof(*sdio_hdr), 0,
+				       GFP_ATOMIC);
+		if (err < 0)
+			return err;
+	}
+
+	/* Prepend MediaTek SDIO Specific Header */
+	skb_push(skb, sizeof(*sdio_hdr));
+
+	sdio_hdr = (void *)skb->data;
+	sdio_hdr->len = cpu_to_le16(skb->len);
+	sdio_hdr->reserved = cpu_to_le16(0);
+	sdio_hdr->bt_type = hci_skb_pkt_type(skb);
+
+	err = sdio_writesb(bdev->func, MTK_REG_CTDR, skb->data,
+			   round_up(skb->len, MTK_SDIO_BLOCK_SIZE));
+	if (err < 0)
+		goto err_skb_pull;
+
+	bdev->hdev->stat.byte_tx += skb->len;
+
+	kfree_skb(skb);
+
+	return 0;
+
+err_skb_pull:
+	skb_pull(skb, sizeof(*sdio_hdr));
+
+	return err;
+}
+
+static u32 btmtksdio_drv_own_query(struct btmtksdio_dev *bdev)
+{
+	return sdio_readl(bdev->func, MTK_REG_CHLPCR, NULL);
+}
+
+static void btmtksdio_tx_work(struct work_struct *work)
+{
+	struct btmtksdio_dev *bdev = container_of(work, struct btmtksdio_dev,
+						  tx_work);
+	struct sk_buff *skb;
+	int err;
+
+	sdio_claim_host(bdev->func);
+
+	while ((skb = skb_dequeue(&bdev->txq))) {
+		err = btmtksdio_tx_packet(bdev, skb);
+		if (err < 0) {
+			bdev->hdev->stat.err_tx++;
+			skb_queue_head(&bdev->txq, skb);
+			break;
+		}
+	}
+
+	sdio_release_host(bdev->func);
+}
+
+static int btmtksdio_recv_event(struct hci_dev *hdev, struct sk_buff *skb)
+{
+	struct btmtksdio_dev *bdev = hci_get_drvdata(hdev);
+	struct hci_event_hdr *hdr = (void *)skb->data;
+	int err;
+
+	/* Fix up the vendor event id with 0xff for vendor specific instead
+	 * of 0xe4 so that event send via monitoring socket can be parsed
+	 * properly.
+	 */
+	if (hdr->evt == 0xe4)
+		hdr->evt = HCI_EV_VENDOR;
+
+	/* When someone waits for the WMT event, the skb is being cloned
+	 * and being processed the events from there then.
+	 */
+	if (test_bit(BTMTKSDIO_TX_WAIT_VND_EVT, &bdev->tx_state)) {
+		bdev->evt_skb = skb_clone(skb, GFP_KERNEL);
+		if (!bdev->evt_skb) {
+			err = -ENOMEM;
+			goto err_out;
+		}
+	}
+
+	err = hci_recv_frame(hdev, skb);
+	if (err < 0)
+		goto err_free_skb;
+
+	if (hdr->evt == HCI_EV_VENDOR) {
+		if (test_and_clear_bit(BTMTKSDIO_TX_WAIT_VND_EVT,
+				       &bdev->tx_state)) {
+			/* Barrier to sync with other CPUs */
+			smp_mb__after_atomic();
+			wake_up_bit(&bdev->tx_state, BTMTKSDIO_TX_WAIT_VND_EVT);
+		}
+	}
+
+	return 0;
+
+err_free_skb:
+	kfree_skb(bdev->evt_skb);
+	bdev->evt_skb = NULL;
+
+err_out:
+	return err;
+}
+
+static const struct h4_recv_pkt mtk_recv_pkts[] = {
+	{ H4_RECV_ACL,      .recv = hci_recv_frame },
+	{ H4_RECV_SCO,      .recv = hci_recv_frame },
+	{ H4_RECV_EVENT,    .recv = btmtksdio_recv_event },
+};
+
+static int btmtksdio_rx_packet(struct btmtksdio_dev *bdev, u16 rx_size)
+{
+	const struct h4_recv_pkt *pkts = mtk_recv_pkts;
+	int pkts_count = ARRAY_SIZE(mtk_recv_pkts);
+	struct mtkbtsdio_hdr *sdio_hdr;
+	unsigned char *old_data;
+	unsigned int old_len;
+	int err, i, pad_size;
+	struct sk_buff *skb;
+	u16 dlen;
+
+	if (rx_size < sizeof(*sdio_hdr))
+		return -EILSEQ;
+
+	/* A SDIO packet is exactly containing a Bluetooth packet */
+	skb = bt_skb_alloc(rx_size, GFP_KERNEL);
+	if (!skb)
+		return -ENOMEM;
+
+	skb_put(skb, rx_size);
+
+	err = sdio_readsb(bdev->func, skb->data, MTK_REG_CRDR, rx_size);
+	if (err < 0)
+		goto err_kfree_skb;
+
+	/* Keep old data for dump the content in case of some error is
+	 * caught in the following packet parsing.
+	 */
+	old_data = skb->data;
+	old_len = skb->len;
+
+	bdev->hdev->stat.byte_rx += rx_size;
+
+	sdio_hdr = (void *)skb->data;
+
+	/* We assume the default error as -EILSEQ simply to make the error path
+	 * be cleaner.
+	 */
+	err = -EILSEQ;
+
+	if (rx_size != le16_to_cpu(sdio_hdr->len)) {
+		bt_dev_err(bdev->hdev, "Rx size in sdio header is mismatched ");
+		goto err_kfree_skb;
+	}
+
+	hci_skb_pkt_type(skb) = sdio_hdr->bt_type;
+
+	/* Remove MediaTek SDIO header */
+	skb_pull(skb, sizeof(*sdio_hdr));
+
+	/* We have to dig into the packet to get payload size and then know how
+	 * many padding bytes at the tail, these padding bytes should be removed
+	 * before the packet is indicated to the core layer.
+	 */
+	for (i = 0; i < pkts_count; i++) {
+		if (sdio_hdr->bt_type == (&pkts[i])->type)
+			break;
+	}
+
+	if (i >= pkts_count) {
+		bt_dev_err(bdev->hdev, "Invalid bt type 0x%02x",
+			   sdio_hdr->bt_type);
+		goto err_kfree_skb;
+	}
+
+	/* Remaining bytes cannot hold a header*/
+	if (skb->len < (&pkts[i])->hlen) {
+		bt_dev_err(bdev->hdev, "The size of bt header is mismatched");
+		goto err_kfree_skb;
+	}
+
+	switch ((&pkts[i])->lsize) {
+		case 1:
+			dlen = skb->data[(&pkts[i])->loff];
+			break;
+		case 2:
+			dlen = get_unaligned_le16(skb->data +
+						  (&pkts[i])->loff);
+			break;
+		default:
+			goto err_kfree_skb;
+	}
+
+	pad_size = skb->len - (&pkts[i])->hlen -  dlen;
+
+	/* Remaining bytes cannot hold a payload */
+	if (pad_size < 0) {
+		bt_dev_err(bdev->hdev, "The size of bt payload is mismatched");
+		goto err_kfree_skb;
+	}
+
+	/* Remove padding bytes */
+	skb_trim(skb, skb->len - pad_size);
+
+	/* Complete frame */
+	(&pkts[i])->recv(bdev->hdev, skb);
+
+	return 0;
+
+err_kfree_skb:
+	print_hex_dump(KERN_ERR, "err sdio rx: ", DUMP_PREFIX_NONE, 4, 1,
+		       old_data, old_len, true);
+	kfree_skb(skb);
+
+	return err;
+}
+
+static void btmtksdio_interrupt(struct sdio_func *func)
+{
+	struct btmtksdio_dev *bdev = sdio_get_drvdata(func);
+	u32 int_status;
+	u16 rx_size;
+
+	/* Disable interrupt */
+	sdio_writel(func, C_INT_EN_CLR, MTK_REG_CHLPCR, 0);
+
+	int_status = sdio_readl(func, MTK_REG_CHISR, NULL);
+
+	/* Ack an interrupt as soon as possible before any operation on
+	 * hardware.
+	 *
+	 * Note that we don't ack any status during operations to avoid race
+	 * condition between the host and the device such as it's possible to
+	 * mistakenly ack RX_DONE for the next packet and then cause interrupts
+	 * not be raised again but there is still pending data in the hardware
+	 * FIFO.
+	 */
+	sdio_writel(func, int_status, MTK_REG_CHISR, NULL);
+
+	if (unlikely(!int_status))
+		bt_dev_err(bdev->hdev, "CHISR is 0\n");
+
+	if (int_status & FW_OWN_BACK_INT)
+		bt_dev_dbg(bdev->hdev, "Get fw own back\n");
+
+	if (int_status & TX_EMPTY)
+		schedule_work(&bdev->tx_work);
+	else if (unlikely(int_status & TX_FIFO_OVERFLOW))
+		bt_dev_warn(bdev->hdev, "Tx fifo overflow\n");
+
+	if (int_status & RX_DONE_INT) {
+		rx_size = (int_status & RX_PKT_LEN) >> 16;
+
+		if (btmtksdio_rx_packet(bdev, rx_size) < 0)
+			bdev->hdev->stat.err_rx++;
+	}
+
+	/* Enable interrupt */
+	sdio_writel(func, C_INT_EN_SET, MTK_REG_CHLPCR, 0);
+}
+
+static int btmtksdio_open(struct hci_dev *hdev)
+{
+	struct btmtksdio_dev *bdev = hci_get_drvdata(hdev);
+	int err;
+	u32 status;
+
+	sdio_claim_host(bdev->func);
+
+	err = sdio_enable_func(bdev->func);
+	if (err < 0)
+		goto err_release_host;
+
+	/* Get ownership from the device */
+	sdio_writel(bdev->func, C_FW_OWN_REQ_CLR, MTK_REG_CHLPCR, &err);
+	if (err < 0)
+		goto err_disable_func;
+
+	err = readx_poll_timeout(btmtksdio_drv_own_query, bdev, status,
+				 status & C_FW_OWN_REQ_SET, 2000, 1000000);
+	if (err < 0) {
+		bt_dev_err(bdev->hdev, "Cannot get ownership from device");
+		goto err_disable_func;
+	}
+
+	/* Disable interrupt & mask out all interrupt sources */
+	sdio_writel(bdev->func, C_INT_EN_CLR, MTK_REG_CHLPCR, &err);
+	if (err < 0)
+		goto err_disable_func;
+
+	sdio_writel(bdev->func, 0, MTK_REG_CHIER, &err);
+	if (err < 0)
+		goto err_disable_func;
+
+	err = sdio_claim_irq(bdev->func, btmtksdio_interrupt);
+	if (err < 0)
+		goto err_disable_func;
+
+	err = sdio_set_block_size(bdev->func, MTK_SDIO_BLOCK_SIZE);
+	if (err < 0)
+		goto err_release_irq;
+
+	/* SDIO CMD 5 allows the SDIO device back to idle state an
+	 * synchronous interrupt is supported in SDIO 4-bit mode
+	 */
+	sdio_writel(bdev->func, SDIO_INT_CTL | SDIO_RE_INIT_EN,
+		    MTK_REG_CSDIOCSR, &err);
+	if (err < 0)
+		goto err_release_irq;
+
+	/* Setup write-1-clear for CHISR register */
+	sdio_writel(bdev->func, C_INT_CLR_CTRL, MTK_REG_CHCR, &err);
+	if (err < 0)
+		goto err_release_irq;
+
+	/* Setup interrupt sources */
+	sdio_writel(bdev->func, RX_DONE_INT | TX_EMPTY | TX_FIFO_OVERFLOW,
+		    MTK_REG_CHIER, &err);
+	if (err < 0)
+		goto err_release_irq;
+
+	/* Enable interrupt */
+	sdio_writel(bdev->func, C_INT_EN_SET, MTK_REG_CHLPCR, &err);
+	if (err < 0)
+		goto err_release_irq;
+
+	sdio_release_host(bdev->func);
+
+	return 0;
+
+err_release_irq:
+	sdio_release_irq(bdev->func);
+
+err_disable_func:
+	sdio_disable_func(bdev->func);
+
+err_release_host:
+	sdio_release_host(bdev->func);
+
+	return err;
+}
+
+static int btmtksdio_close(struct hci_dev *hdev)
+{
+	struct btmtksdio_dev *bdev = hci_get_drvdata(hdev);
+	u32 status;
+	int err;
+
+	sdio_claim_host(bdev->func);
+
+	/* Disable interrupt */
+	sdio_writel(bdev->func, C_INT_EN_CLR, MTK_REG_CHLPCR, NULL);
+
+	sdio_release_irq(bdev->func);
+
+	/* Return ownership to the device */
+	sdio_writel(bdev->func, C_FW_OWN_REQ_SET, MTK_REG_CHLPCR, NULL);
+
+	err = readx_poll_timeout(btmtksdio_drv_own_query, bdev, status,
+				 !(status & C_FW_OWN_REQ_SET), 2000, 1000000);
+	if (err < 0)
+		bt_dev_err(bdev->hdev, "Cannot return ownership to device");
+
+	sdio_disable_func(bdev->func);
+
+	sdio_release_host(bdev->func);
+
+	return 0;
+}
+
+static int btmtksdio_flush(struct hci_dev *hdev)
+{
+	struct btmtksdio_dev *bdev = hci_get_drvdata(hdev);
+
+	skb_queue_purge(&bdev->txq);
+
+	cancel_work_sync(&bdev->tx_work);
+
+	return 0;
+}
+
+static int btmtksdio_func_query(struct hci_dev *hdev)
+{
+	struct btmtk_hci_wmt_params wmt_params;
+	int status, err;
+	u8 param = 0;
+
+	/* Query whether the function is enabled */
+	wmt_params.op = MTK_WMT_FUNC_CTRL;
+	wmt_params.flag = 4;
+	wmt_params.dlen = sizeof(param);
+	wmt_params.data = &param;
+	wmt_params.status = &status;
+
+	err = mtk_hci_wmt_sync(hdev, &wmt_params);
+	if (err < 0) {
+		bt_dev_err(hdev, "Failed to query function status (%d)", err);
+		return err;
+	}
+
+	return status;
+}
+
+static int mtk_setup_firmware(struct hci_dev *hdev, const char *fwname)
+{
+	struct btmtk_hci_wmt_params wmt_params;
+	const struct firmware *fw;
+	const u8 *fw_ptr;
+	size_t fw_size;
+	int err, dlen;
+	u8 flag;
+
+	err = request_firmware(&fw, fwname, &hdev->dev);
+	if (err < 0) {
+		bt_dev_err(hdev, "Failed to load firmware file (%d)", err);
+		return err;
+	}
+
+	fw_ptr = fw->data;
+	fw_size = fw->size;
+
+	/* The size of patch header is 30 bytes, should be skip */
+	if (fw_size < 30) {
+		err = -EINVAL;
+		goto free_fw;
+	}
+
+	fw_size -= 30;
+	fw_ptr += 30;
+	flag = 1;
+
+	wmt_params.op = MTK_WMT_PATCH_DWNLD;
+	wmt_params.status = NULL;
+
+	while (fw_size > 0) {
+		dlen = min_t(int, 250, fw_size);
+
+		/* Tell device the position in sequence */
+		if (fw_size - dlen <= 0)
+			flag = 3;
+		else if (fw_size < fw->size - 30)
+			flag = 2;
+
+		wmt_params.flag = flag;
+		wmt_params.dlen = dlen;
+		wmt_params.data = fw_ptr;
+
+		err = mtk_hci_wmt_sync(hdev, &wmt_params);
+		if (err < 0) {
+			bt_dev_err(hdev, "Failed to send wmt patch dwnld (%d)",
+				   err);
+			goto free_fw;
+		}
+
+		fw_size -= dlen;
+		fw_ptr += dlen;
+	}
+
+	wmt_params.op = MTK_WMT_RST;
+	wmt_params.flag = 4;
+	wmt_params.dlen = 0;
+	wmt_params.data = NULL;
+	wmt_params.status = NULL;
+
+	/* Activate funciton the firmware providing to */
+	err = mtk_hci_wmt_sync(hdev, &wmt_params);
+	if (err < 0) {
+		bt_dev_err(hdev, "Failed to send wmt rst (%d)", err);
+		goto free_fw;
+	}
+
+	/* Wait a few moments for firmware activation done */
+	usleep_range(10000, 12000);
+
+free_fw:
+	release_firmware(fw);
+	return err;
+}
+
+static int btmtksdio_setup(struct hci_dev *hdev)
+{
+	struct btmtksdio_dev *bdev = hci_get_drvdata(hdev);
+	struct btmtk_hci_wmt_params wmt_params;
+	ktime_t calltime, delta, rettime;
+	struct btmtk_tci_sleep tci_sleep;
+	unsigned long long duration;
+	struct sk_buff *skb;
+	int err, status;
+	u8 param = 0x1;
+
+	calltime = ktime_get();
+
+	/* Query whether the firmware is already download */
+	wmt_params.op = MTK_WMT_SEMAPHORE;
+	wmt_params.flag = 1;
+	wmt_params.dlen = 0;
+	wmt_params.data = NULL;
+	wmt_params.status = &status;
+
+	err = mtk_hci_wmt_sync(hdev, &wmt_params);
+	if (err < 0) {
+		bt_dev_err(hdev, "Failed to query firmware status (%d)", err);
+		return err;
+	}
+
+	if (status == BTMTK_WMT_PATCH_DONE) {
+		bt_dev_info(hdev, "Firmware already downloaded");
+		goto ignore_setup_fw;
+	}
+
+	/* Setup a firmware which the device definitely requires */
+	err = mtk_setup_firmware(hdev, bdev->data->fwname);
+	if (err < 0)
+		return err;
+
+ignore_setup_fw:
+	/* Query whether the device is already enabled */
+	err = readx_poll_timeout(btmtksdio_func_query, hdev, status,
+				 status < 0 || status != BTMTK_WMT_ON_PROGRESS,
+				 2000, 5000000);
+	/* -ETIMEDOUT happens */
+	if (err < 0)
+		return err;
+
+	/* The other errors happen in btusb_mtk_func_query */
+	if (status < 0)
+		return status;
+
+	if (status == BTMTK_WMT_ON_DONE) {
+		bt_dev_info(hdev, "function already on");
+		goto ignore_func_on;
+	}
+
+	/* Enable Bluetooth protocol */
+	wmt_params.op = MTK_WMT_FUNC_CTRL;
+	wmt_params.flag = 0;
+	wmt_params.dlen = sizeof(param);
+	wmt_params.data = &param;
+	wmt_params.status = NULL;
+
+	err = mtk_hci_wmt_sync(hdev, &wmt_params);
+	if (err < 0) {
+		bt_dev_err(hdev, "Failed to send wmt func ctrl (%d)", err);
+		return err;
+	}
+
+ignore_func_on:
+	/* Apply the low power environment setup */
+	tci_sleep.mode = 0x5;
+	tci_sleep.duration = cpu_to_le16(0x640);
+	tci_sleep.host_duration = cpu_to_le16(0x640);
+	tci_sleep.host_wakeup_pin = 0;
+	tci_sleep.time_compensation = 0;
+
+	skb = __hci_cmd_sync(hdev, 0xfc7a, sizeof(tci_sleep), &tci_sleep,
+			     HCI_INIT_TIMEOUT);
+	if (IS_ERR(skb)) {
+		err = PTR_ERR(skb);
+		bt_dev_err(hdev, "Failed to apply low power setting (%d)", err);
+		return err;
+	}
+	kfree_skb(skb);
+
+	rettime = ktime_get();
+	delta = ktime_sub(rettime, calltime);
+	duration = (unsigned long long)ktime_to_ns(delta) >> 10;
+
+	bt_dev_info(hdev, "Device setup in %llu usecs", duration);
+
+	return 0;
+}
+
+static int btmtksdio_shutdown(struct hci_dev *hdev)
+{
+	struct btmtk_hci_wmt_params wmt_params;
+	u8 param = 0x0;
+	int err;
+
+	/* Disable the device */
+	wmt_params.op = MTK_WMT_FUNC_CTRL;
+	wmt_params.flag = 0;
+	wmt_params.dlen = sizeof(param);
+	wmt_params.data = &param;
+	wmt_params.status = NULL;
+
+	err = mtk_hci_wmt_sync(hdev, &wmt_params);
+	if (err < 0) {
+		bt_dev_err(hdev, "Failed to send wmt func ctrl (%d)", err);
+		return err;
+	}
+
+	return 0;
+}
+
+static int btmtksdio_send_frame(struct hci_dev *hdev, struct sk_buff *skb)
+{
+	struct btmtksdio_dev *bdev = hci_get_drvdata(hdev);
+
+	switch (hci_skb_pkt_type(skb)) {
+	case HCI_COMMAND_PKT:
+		hdev->stat.cmd_tx++;
+		break;
+
+	case HCI_ACLDATA_PKT:
+		hdev->stat.acl_tx++;
+		break;
+
+	case HCI_SCODATA_PKT:
+		hdev->stat.sco_tx++;
+		break;
+
+	default:
+		return -EILSEQ;
+	}
+
+	skb_queue_tail(&bdev->txq, skb);
+
+	schedule_work(&bdev->tx_work);
+
+	return 0;
+}
+
+static int btmtksdio_probe(struct sdio_func *func,
+			   const struct sdio_device_id *id)
+{
+	struct btmtksdio_dev *bdev;
+	struct hci_dev *hdev;
+	int err;
+
+	bdev = devm_kzalloc(&func->dev, sizeof(*bdev), GFP_KERNEL);
+	if (!bdev)
+		return -ENOMEM;
+
+	bdev->data = (void *)id->driver_data;
+	if (!bdev->data)
+		return -ENODEV;
+
+	bdev->func = func;
+
+	INIT_WORK(&bdev->tx_work, btmtksdio_tx_work);
+	skb_queue_head_init(&bdev->txq);
+
+	/* Initialize and register HCI device */
+	hdev = hci_alloc_dev();
+	if (!hdev) {
+		dev_err(&func->dev, "Can't allocate HCI device\n");
+		return -ENOMEM;
+	}
+
+	bdev->hdev = hdev;
+
+	hdev->bus = HCI_SDIO;
+	hci_set_drvdata(hdev, bdev);
+
+	hdev->open     = btmtksdio_open;
+	hdev->close    = btmtksdio_close;
+	hdev->flush    = btmtksdio_flush;
+	hdev->setup    = btmtksdio_setup;
+	hdev->shutdown = btmtksdio_shutdown;
+	hdev->send     = btmtksdio_send_frame;
+	SET_HCIDEV_DEV(hdev, &func->dev);
+
+	hdev->manufacturer = 70;
+	set_bit(HCI_QUIRK_NON_PERSISTENT_SETUP, &hdev->quirks);
+
+	err = hci_register_dev(hdev);
+	if (err < 0) {
+		dev_err(&func->dev, "Can't register HCI device\n");
+		hci_free_dev(hdev);
+		return err;
+	}
+
+	sdio_set_drvdata(func, bdev);
+
+	return 0;
+}
+
+static void btmtksdio_remove(struct sdio_func *func)
+{
+	struct btmtksdio_dev *bdev = sdio_get_drvdata(func);
+	struct hci_dev *hdev;
+
+	if (!bdev)
+		return;
+
+	hdev = bdev->hdev;
+
+	sdio_set_drvdata(func, NULL);
+	hci_unregister_dev(hdev);
+	hci_free_dev(hdev);
+}
+
+static struct sdio_driver btmtksdio_driver = {
+	.name		= "btmtksdio",
+	.probe		= btmtksdio_probe,
+	.remove		= btmtksdio_remove,
+	.id_table	= btmtksdio_table,
+};
+
+static int __init btmtksdio_init(void)
+{
+	BT_INFO("MediaTek Bluetooth SDIO driver ver %s", VERSION);
+
+	return sdio_register_driver(&btmtksdio_driver);
+}
+
+static void __exit btmtksdio_exit(void)
+{
+	sdio_unregister_driver(&btmtksdio_driver);
+}
+
+module_init(btmtksdio_init);
+module_exit(btmtksdio_exit);
+
+MODULE_AUTHOR("Sean Wang <sean.wang@mediatek.com>");
+MODULE_DESCRIPTION("MediaTek Bluetooth SDIO driver ver " VERSION);
+MODULE_VERSION(VERSION);
+MODULE_LICENSE("GPL");
+MODULE_FIRMWARE(FIRMWARE_MT7663);
+MODULE_FIRMWARE(FIRMWARE_MT7668);
