new file mode 100644
@@ -0,0 +1,18 @@
+* SPEAr SDHCI Controller
+
+Required properties:
+- compatible : "st,spear300-sdhci"
+
+Optional Properties:
+- cd-gpios: card detect gpio, with zero flags.
+
+If your board don't support these gpios then don't pass the entry.
+
+Example:
+
+ sdhci@fc000000 {
+ compatible = "st,spear300-sdhci";
+ reg = <0xfc000000 0x1000>;
+
+ cd-gpios = <&gpio0 6 0>
+ };
@@ -80,8 +80,7 @@
};
sdhci@70000000 {
- int-gpio = <&gpio1 0 0>;
- power-gpio = <&gpio1 2 1>;
+ cd-gpios = <&gpio1 0 0>;
status = "okay";
};
@@ -103,8 +103,6 @@
};
sdhci@70000000 {
- power-gpio = <&gpio0 2 1>;
- power_always_enb;
status = "okay";
};
@@ -20,6 +20,8 @@
#include <linux/module.h>
#include <linux/interrupt.h>
#include <linux/irq.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
#include <linux/platform_device.h>
#include <linux/pm.h>
#include <linux/slab.h>
@@ -68,8 +70,42 @@ static irqreturn_t sdhci_gpio_irq(int irq, void *dev_id)
return IRQ_HANDLED;
}
+#ifdef CONFIG_OF
+static struct sdhci_plat_data * __devinit
+sdhci_probe_config_dt(struct platform_device *pdev)
+{
+ struct device_node *np = pdev->dev.of_node;
+ struct sdhci_plat_data *pdata = NULL;
+ int cd_gpio;
+
+ cd_gpio = of_get_named_gpio(np, "cd-gpios", 0);
+ if (!gpio_is_valid(cd_gpio))
+ cd_gpio = -1;
+
+ /* If pdata is required */
+ if (cd_gpio != -1) {
+ pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
+ if (!pdata) {
+ dev_err(&pdev->dev, "DT: kzalloc failed\n");
+ return ERR_PTR(-ENOMEM);
+ }
+ }
+
+ pdata->card_int_gpio = cd_gpio;
+
+ return pdata;
+}
+#else
+static struct sdhci_plat_data * __devinit
+sdhci_probe_config_dt(struct platform_device *pdev)
+{
+ return ERR_PTR(-ENOSYS);
+}
+#endif
+
static int __devinit sdhci_probe(struct platform_device *pdev)
{
+ struct device_node *np = pdev->dev.of_node;
struct sdhci_host *host;
struct resource *iomem;
struct spear_sdhci *sdhci;
@@ -110,8 +146,16 @@ static int __devinit sdhci_probe(struct platform_device *pdev)
goto put_clk;
}
- /* overwrite platform_data */
- sdhci->data = dev_get_platdata(&pdev->dev);
+ if (np) {
+ sdhci->data = sdhci_probe_config_dt(pdev);
+ if (IS_ERR(sdhci->data)) {
+ dev_err(&pdev->dev, "DT: Failed to get pdata\n");
+ return -ENODEV;
+ }
+ } else {
+ sdhci->data = dev_get_platdata(&pdev->dev);
+ }
+
pdev->dev.platform_data = sdhci;
if (pdev->dev.parent)
@@ -276,11 +320,20 @@ static int sdhci_resume(struct device *dev)
static SIMPLE_DEV_PM_OPS(sdhci_pm_ops, sdhci_suspend, sdhci_resume);
+#ifdef CONFIG_OF
+static const struct of_device_id sdhci_spear_id_table[] = {
+ { .compatible = "st,spear300-sdhci" },
+ {}
+};
+MODULE_DEVICE_TABLE(of, sdhci_spear_id_table);
+#endif
+
static struct platform_driver sdhci_driver = {
.driver = {
.name = "sdhci",
.owner = THIS_MODULE,
.pm = &sdhci_pm_ops,
+ .of_match_table = of_match_ptr(sdhci_spear_id_table),
},
.probe = sdhci_probe,
.remove = __devexit_p(sdhci_remove),
This adds simple DT bindings for SDHCI SPEAr controller. It uses cd-gpios from common mmc bindings. This also fixes spear300-evb.dts with correct name for card detect binding. Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> --- V1->V2: - Use cd-gpios instead of int-gpio as binding for card detect gpio. - Fix spear300-evb.dts binding name for cd-gpios - Removed power-gpio from DT bindings and code, must be handled via regulators .../devicetree/bindings/mmc/sdhci-spear.txt | 18 +++++++ arch/arm/boot/dts/spear300-evb.dts | 3 +- arch/arm/boot/dts/spear320-evb.dts | 2 - drivers/mmc/host/sdhci-spear.c | 57 +++++++++++++++++++++- 4 files changed, 74 insertions(+), 6 deletions(-) create mode 100644 Documentation/devicetree/bindings/mmc/sdhci-spear.txt