@@ -32,6 +32,131 @@
#include <plat/serial.h>
#include <plat/cbus.h>
+
+#if defined(CONFIG_USB_MUSB_OTG)
+#define BOARD_MODE MUSB_OTG
+#elif defined(CONFIG_USB_MUSB_PERIPHERAL)
+#define BOARD_MODE MUSB_PERIPHERAL
+#else /* defined(CONFIG_USB_MUSB_HOST) */
+#define BOARD_MODE MUSB_HOST
+#endif
+
+/*
+ * Enable or disable power to TUSB6010. When enabling, turn on 3.3 V and
+ * 1.5 V voltage regulators of PM companion chip. Companion chip will then
+ * provide then PGOOD signal to TUSB6010 which will release it from reset.
+ */
+static int tusb_set_power(int state)
+{
+ int i, retval = 0;
+
+ if (state) {
+ gpio_set_value(TUSB6010_GPIO_ENABLE, 1);
+ msleep(1);
+
+ /* Wait until TUSB6010 pulls INT pin down */
+ i = 100;
+ while (i && gpio_get_value(TUSB6010_GPIO_INT)) {
+ msleep(1);
+ i--;
+ }
+
+ if (!i) {
+ printk(KERN_ERR "tusb: powerup failed\n");
+ retval = -ENODEV;
+ }
+ } else {
+ gpio_set_value(TUSB6010_GPIO_ENABLE, 0);
+ msleep(10);
+ }
+
+ return retval;
+}
+
+
+static struct musb_hdrc_eps_bits musb_eps[] = {
+ { "ep1_tx", 5, },
+ { "ep1_rx", 5, },
+ { "ep2_tx", 5, },
+ { "ep2_rx", 5, },
+ { "ep3_tx", 3, },
+ { "ep3_rx", 3, },
+ { "ep4_tx", 3, },
+ { "ep4_rx", 3, },
+ { "ep5_tx", 2, },
+ { "ep5_rx", 2, },
+ { "ep6_tx", 2, },
+ { "ep6_rx", 2, },
+ { "ep7_tx", 2, },
+ { "ep7_rx", 2, },
+ { "ep8_tx", 2, },
+ { "ep8_rx", 2, },
+ { "ep9_tx", 2, },
+ { "ep9_rx", 2, },
+ { "ep10_tx", 2, },
+ { "ep10_rx", 2, },
+ { "ep11_tx", 2, },
+ { "ep11_rx", 2, },
+ { "ep12_tx", 2, },
+ { "ep12_rx", 2, },
+ { "ep13_tx", 2, },
+ { "ep13_rx", 2, },
+ { "ep14_tx", 2, },
+ { "ep14_rx", 2, },
+ { "ep15_tx", 2, },
+ { "ep15_rx", 2, },
+};
+
+static struct musb_hdrc_config musb_config = {
+ .multipoint = 1,
+ .dyn_fifo = 1,
+ .soft_con = 1,
+ .dma = 1,
+ .num_eps = 16,
+ .dma_channels = 7,
+ .ram_bits = 12,
+ .eps_bits = musb_eps,
+};
+
+static struct musb_hdrc_platform_data tusb_data = {
+ .mode = BOARD_MODE,
+ .set_power = tusb_set_power,
+ .min_power = 25, /* x2 = 50 mA drawn from VBUS as peripheral */
+ .power = 100, /* Max 100 mA VBUS for host mode */
+ .config = &musb_config,
+};
+
+static void __init n8x0_usb_init(void)
+{
+ int ret = 0;
+ static char announce[] __initdata = KERN_INFO "TUSB 6010\n";
+
+ /* PM companion chip power control pin */
+ ret = gpio_request(TUSB6010_GPIO_ENABLE, "TUSB6010 enable");
+ if (ret != 0) {
+ printk(KERN_ERR "Could not get TUSB power GPIO%i\n",
+ TUSB6010_GPIO_ENABLE);
+ return;
+ }
+ gpio_direction_output(TUSB6010_GPIO_ENABLE, 0);
+
+ tusb_set_power(0);
+
+ ret = tusb6010_setup_interface(&tusb_data, TUSB6010_REFCLK_19, 2,
+ TUSB6010_ASYNC_CS, TUSB6010_SYNC_CS,
+ TUSB6010_GPIO_INT, 0x3f);
+ if (ret != 0)
+ goto err;
+
+ printk(announce);
+
+ return;
+
+err:
+ gpio_free(TUSB6010_GPIO_ENABLE);
+}
+
+
static struct omap2_mcspi_device_config p54spi_mcspi_config = {
.turbo_mode = 0,
.single_channel = 1,
@@ -148,6 +273,7 @@ static void __init n8x0_init_machine(void)
omap_serial_init();
n8x0_onenand_init();
+ n8x0_usb_init();
}
MACHINE_START(NOKIA_N800, "Nokia N800")
@@ -1841,6 +1841,7 @@ static struct omap_clk omap2420_clks[] = {
CLK(NULL, "aes_ick", &aes_ick, CK_242X),
CLK(NULL, "pka_ick", &pka_ick, CK_242X),
CLK(NULL, "usb_fck", &usb_fck, CK_242X),
+ CLK("musb_hdrc", "fck", &osc_ck, CK_242X),
};
/*
@@ -98,6 +98,10 @@ struct musb_hdrc_platform_data {
#define TUSB6010_OSCCLK_60 16667 /* psec/clk @ 60.0 MHz */
#define TUSB6010_REFCLK_24 41667 /* psec/clk @ 24.0 MHz XI */
#define TUSB6010_REFCLK_19 52083 /* psec/clk @ 19.2 MHz CLKIN */
+#define TUSB6010_ASYNC_CS 1
+#define TUSB6010_SYNC_CS 4
+#define TUSB6010_GPIO_INT 58
+#define TUSB6010_GPIO_ENABLE 0
#ifdef CONFIG_ARCH_OMAP2