===================================================================
@@ -290,161 +290,165 @@ static int omap3_start_ohci(struct ohci_
dev_dbg(omap->dev, "starting TI OHCI USB Controller\n");
- /* Get all the clock handles we need */
- omap->usbhost_ick = clk_get(omap->dev, "usbhost_ick");
- if (IS_ERR(omap->usbhost_ick)) {
- dev_err(omap->dev, "could not get usbhost_ick\n");
- ret = PTR_ERR(omap->usbhost_ick);
- goto err_host_ick;
- }
-
- omap->usbhost_hs_fck = clk_get(omap->dev, "usbhost_120m_fck");
- if (IS_ERR(omap->usbhost_hs_fck)) {
- dev_err(omap->dev, "could not get usbhost_120m_fck\n");
- ret = PTR_ERR(omap->usbhost_hs_fck);
- goto err_host_hs_fck;
- }
-
- omap->usbhost_fs_fck = clk_get(omap->dev, "usbhost_48m_fck");
- if (IS_ERR(omap->usbhost_fs_fck)) {
- dev_err(omap->dev, "could not get usbhost_48m_fck\n");
- ret = PTR_ERR(omap->usbhost_fs_fck);
- goto err_host_fs_fck;
- }
+ if (cpu_is_omap44xx()) {
+ /* TODO */
+ } else {
+ /* Get all the clock handles we need */
+ omap->usbhost_ick = clk_get(omap->dev, "usbhost_ick");
+ if (IS_ERR(omap->usbhost_ick)) {
+ dev_err(omap->dev, "could not get usbhost_ick\n");
+ ret = PTR_ERR(omap->usbhost_ick);
+ goto err_host_ick;
+ }
- omap->usbtll_fck = clk_get(omap->dev, "usbtll_fck");
- if (IS_ERR(omap->usbtll_fck)) {
- dev_err(omap->dev, "could not get usbtll_fck\n");
- ret = PTR_ERR(omap->usbtll_fck);
- goto err_tll_fck;
- }
+ omap->usbhost_hs_fck = clk_get(omap->dev, "usbhost_120m_fck");
+ if (IS_ERR(omap->usbhost_hs_fck)) {
+ dev_err(omap->dev, "could not get usbhost_120m_fck\n");
+ ret = PTR_ERR(omap->usbhost_hs_fck);
+ goto err_host_hs_fck;
+ }
- omap->usbtll_ick = clk_get(omap->dev, "usbtll_ick");
- if (IS_ERR(omap->usbtll_ick)) {
- dev_err(omap->dev, "could not get usbtll_ick\n");
- ret = PTR_ERR(omap->usbtll_ick);
- goto err_tll_ick;
- }
+ omap->usbhost_fs_fck = clk_get(omap->dev, "usbhost_48m_fck");
+ if (IS_ERR(omap->usbhost_fs_fck)) {
+ dev_err(omap->dev, "could not get usbhost_48m_fck\n");
+ ret = PTR_ERR(omap->usbhost_fs_fck);
+ goto err_host_fs_fck;
+ }
- /* Now enable all the clocks in the correct order */
- ohci_omap3_clock_power(omap, 1);
+ omap->usbtll_fck = clk_get(omap->dev, "usbtll_fck");
+ if (IS_ERR(omap->usbtll_fck)) {
+ dev_err(omap->dev, "could not get usbtll_fck\n");
+ ret = PTR_ERR(omap->usbtll_fck);
+ goto err_tll_fck;
+ }
- /* perform TLL soft reset, and wait until reset is complete */
- ohci_omap_writel(omap->tll_base, OMAP_USBTLL_SYSCONFIG,
- OMAP_USBTLL_SYSCONFIG_SOFTRESET);
+ omap->usbtll_ick = clk_get(omap->dev, "usbtll_ick");
+ if (IS_ERR(omap->usbtll_ick)) {
+ dev_err(omap->dev, "could not get usbtll_ick\n");
+ ret = PTR_ERR(omap->usbtll_ick);
+ goto err_tll_ick;
+ }
- /* Wait for TLL reset to complete */
- while (!(ohci_omap_readl(omap->tll_base, OMAP_USBTLL_SYSSTATUS)
- & OMAP_USBTLL_SYSSTATUS_RESETDONE)) {
- cpu_relax();
+ /* Now enable all the clocks in the correct order */
+ ohci_omap3_clock_power(omap, 1);
- if (time_after(jiffies, timeout)) {
- dev_dbg(omap->dev, "operation timed out\n");
- ret = -EINVAL;
- goto err_sys_status;
+ /* perform TLL soft reset, and wait until reset is complete */
+ ohci_omap_writel(omap->tll_base, OMAP_USBTLL_SYSCONFIG,
+ OMAP_USBTLL_SYSCONFIG_SOFTRESET);
+
+ /* Wait for TLL reset to complete */
+ while (!(ohci_omap_readl(omap->tll_base, OMAP_USBTLL_SYSSTATUS)
+ & OMAP_USBTLL_SYSSTATUS_RESETDONE)) {
+ cpu_relax();
+
+ if (time_after(jiffies, timeout)) {
+ dev_dbg(omap->dev, "operation timed out\n");
+ ret = -EINVAL;
+ goto err_sys_status;
+ }
}
- }
- dev_dbg(omap->dev, "TLL reset done\n");
+ dev_dbg(omap->dev, "TLL reset done\n");
- /* (1<<3) = no idle mode only for initial debugging */
- ohci_omap_writel(omap->tll_base, OMAP_USBTLL_SYSCONFIG,
- OMAP_USBTLL_SYSCONFIG_ENAWAKEUP |
- OMAP_USBTLL_SYSCONFIG_SIDLEMODE |
- OMAP_USBTLL_SYSCONFIG_CACTIVITY);
+ /* (1<<3) = no idle mode only for initial debugging */
+ ohci_omap_writel(omap->tll_base, OMAP_USBTLL_SYSCONFIG,
+ OMAP_USBTLL_SYSCONFIG_ENAWAKEUP |
+ OMAP_USBTLL_SYSCONFIG_SIDLEMODE |
+ OMAP_USBTLL_SYSCONFIG_CACTIVITY);
- /* Put UHH in NoIdle/NoStandby mode */
- reg = ohci_omap_readl(omap->uhh_base, OMAP_UHH_SYSCONFIG);
- reg |= (OMAP_UHH_SYSCONFIG_ENAWAKEUP
+ /* Put UHH in NoIdle/NoStandby mode */
+ reg = ohci_omap_readl(omap->uhh_base, OMAP_UHH_SYSCONFIG);
+ reg |= (OMAP_UHH_SYSCONFIG_ENAWAKEUP
| OMAP_UHH_SYSCONFIG_SIDLEMODE
| OMAP_UHH_SYSCONFIG_CACTIVITY
| OMAP_UHH_SYSCONFIG_MIDLEMODE);
- reg &= ~OMAP_UHH_SYSCONFIG_AUTOIDLE;
- reg &= ~OMAP_UHH_SYSCONFIG_SOFTRESET;
+ reg &= ~OMAP_UHH_SYSCONFIG_AUTOIDLE;
+ reg &= ~OMAP_UHH_SYSCONFIG_SOFTRESET;
- ohci_omap_writel(omap->uhh_base, OMAP_UHH_SYSCONFIG, reg);
+ ohci_omap_writel(omap->uhh_base, OMAP_UHH_SYSCONFIG, reg);
- reg = ohci_omap_readl(omap->uhh_base, OMAP_UHH_HOSTCONFIG);
+ reg = ohci_omap_readl(omap->uhh_base, OMAP_UHH_HOSTCONFIG);
- /* setup ULPI bypass and burst configurations */
- reg |= (OMAP_UHH_HOSTCONFIG_INCR4_BURST_EN
+ /* setup ULPI bypass and burst configurations */
+ reg |= (OMAP_UHH_HOSTCONFIG_INCR4_BURST_EN
| OMAP_UHH_HOSTCONFIG_INCR8_BURST_EN
| OMAP_UHH_HOSTCONFIG_INCR16_BURST_EN);
- reg &= ~OMAP_UHH_HOSTCONFIG_INCRX_ALIGN_EN;
+ reg &= ~OMAP_UHH_HOSTCONFIG_INCRX_ALIGN_EN;
- /*
- * REVISIT: Pi_CONNECT_STATUS controls MStandby
- * assertion and Swakeup generation - let us not
- * worry about this for now. OMAP HWMOD framework
- * might take care of this later. If not, we can
- * update these registers when adding aggressive
- * clock management code.
- *
- * For now, turn off all the Pi_CONNECT_STATUS bits
- *
- if (omap->port_mode[0] == OMAP_OHCI_PORT_MODE_UNUSED)
- reg &= ~OMAP_UHH_HOSTCONFIG_P1_CONNECT_STATUS;
- if (omap->port_mode[1] == OMAP_OHCI_PORT_MODE_UNUSED)
- reg &= ~OMAP_UHH_HOSTCONFIG_P2_CONNECT_STATUS;
- if (omap->port_mode[2] == OMAP_OHCI_PORT_MODE_UNUSED)
- reg &= ~OMAP_UHH_HOSTCONFIG_P3_CONNECT_STATUS;
- */
- reg &= ~OMAP_UHH_HOSTCONFIG_P1_CONNECT_STATUS;
- reg &= ~OMAP_UHH_HOSTCONFIG_P2_CONNECT_STATUS;
- reg &= ~OMAP_UHH_HOSTCONFIG_P3_CONNECT_STATUS;
-
- if (omap->es2_compatibility) {
/*
- * All OHCI modes need to go through the TLL,
- * unlike in the EHCI case. So use UTMI mode
- * for all ports for OHCI, on ES2.x silicon
- */
- dev_dbg(omap->dev, "OMAP3 ES version <= ES2.1\n");
- reg |= OMAP_UHH_HOSTCONFIG_ULPI_BYPASS;
- } else {
- dev_dbg(omap->dev, "OMAP3 ES version > ES2.1\n");
+ * REVISIT: Pi_CONNECT_STATUS controls MStandby
+ * assertion and Swakeup generation - let us not
+ * worry about this for now. OMAP HWMOD framework
+ * might take care of this later. If not, we can
+ * update these registers when adding aggressive
+ * clock management code.
+ *
+ * For now, turn off all the Pi_CONNECT_STATUS bits
+ *
if (omap->port_mode[0] == OMAP_OHCI_PORT_MODE_UNUSED)
- reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS;
- else
- reg |= OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS;
-
+ reg &= ~OMAP_UHH_HOSTCONFIG_P1_CONNECT_STATUS;
if (omap->port_mode[1] == OMAP_OHCI_PORT_MODE_UNUSED)
- reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P2_BYPASS;
- else
- reg |= OMAP_UHH_HOSTCONFIG_ULPI_P2_BYPASS;
-
+ reg &= ~OMAP_UHH_HOSTCONFIG_P2_CONNECT_STATUS;
if (omap->port_mode[2] == OMAP_OHCI_PORT_MODE_UNUSED)
- reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS;
- else
- reg |= OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS;
+ reg &= ~OMAP_UHH_HOSTCONFIG_P3_CONNECT_STATUS;
+ */
+ reg &= ~OMAP_UHH_HOSTCONFIG_P1_CONNECT_STATUS;
+ reg &= ~OMAP_UHH_HOSTCONFIG_P2_CONNECT_STATUS;
+ reg &= ~OMAP_UHH_HOSTCONFIG_P3_CONNECT_STATUS;
- }
- ohci_omap_writel(omap->uhh_base, OMAP_UHH_HOSTCONFIG, reg);
- dev_dbg(omap->dev, "UHH setup done, uhh_hostconfig=%x\n", reg);
+ if (omap->es2_compatibility) {
+ /*
+ * All OHCI modes need to go through the TLL,
+ * unlike in the EHCI case. So use UTMI mode
+ * for all ports for OHCI, on ES2.x silicon
+ */
+ dev_dbg(omap->dev, "OMAP3 ES version <= ES2.1\n");
+ reg |= OMAP_UHH_HOSTCONFIG_ULPI_BYPASS;
+ } else {
+ dev_dbg(omap->dev, "OMAP3 ES version > ES2.1\n");
+ if (omap->port_mode[0] == OMAP_OHCI_PORT_MODE_UNUSED)
+ reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS;
+ else
+ reg |= OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS;
+
+ if (omap->port_mode[1] == OMAP_OHCI_PORT_MODE_UNUSED)
+ reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P2_BYPASS;
+ else
+ reg |= OMAP_UHH_HOSTCONFIG_ULPI_P2_BYPASS;
+
+ if (omap->port_mode[2] == OMAP_OHCI_PORT_MODE_UNUSED)
+ reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS;
+ else
+ reg |= OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS;
- ohci_omap3_tll_config(omap, OMAP_TLL_CHANNEL_COUNT);
+ }
+ ohci_omap_writel(omap->uhh_base, OMAP_UHH_HOSTCONFIG, reg);
+ dev_dbg(omap->dev, "UHH setup done, uhh_hostconfig=%x\n", reg);
- return 0;
+ ohci_omap3_tll_config(omap, OMAP_TLL_CHANNEL_COUNT);
+
+ return 0;
err_sys_status:
- ohci_omap3_clock_power(omap, 0);
- clk_put(omap->usbtll_ick);
+ ohci_omap3_clock_power(omap, 0);
+ clk_put(omap->usbtll_ick);
err_tll_ick:
- clk_put(omap->usbtll_fck);
+ clk_put(omap->usbtll_fck);
err_tll_fck:
- clk_put(omap->usbhost_fs_fck);
+ clk_put(omap->usbhost_fs_fck);
err_host_fs_fck:
- clk_put(omap->usbhost_hs_fck);
+ clk_put(omap->usbhost_hs_fck);
err_host_hs_fck:
- clk_put(omap->usbhost_ick);
+ clk_put(omap->usbhost_ick);
err_host_ick:
- return ret;
+ return ret;
+ }
}
static void omap3_stop_ohci(struct ohci_hcd_omap3 *omap, struct usb_hcd *hcd)