@@ -51,7 +51,8 @@ obj-$(CONFIG_ARCH_OMAP2) += sdrc2xxx.o
ifeq ($(CONFIG_PM),y)
obj-$(CONFIG_ARCH_OMAP2) += pm24xx.o
obj-$(CONFIG_ARCH_OMAP2) += sleep24xx.o pm_bus.o
-obj-$(CONFIG_ARCH_OMAP3) += pm34xx.o sleep34xx.o cpuidle34xx.o pm_bus.o
+obj-$(CONFIG_ARCH_OMAP3) += pm34xx.o sleep34xx.o voltage.o \
+ cpuidle34xx.o pm_bus.o
obj-$(CONFIG_ARCH_OMAP4) += pm44xx.o pm_bus.o
obj-$(CONFIG_PM_DEBUG) += pm-debug.o
new file mode 100644
@@ -0,0 +1,1158 @@
+/*
+ * OMAP3/OMAP4 Voltage Management Routines
+ *
+ * Author: Thara Gopinath <thara@ti.com>
+ *
+ * Copyright (C) 2007 Texas Instruments, Inc.
+ * Rajendra Nayak <rnayak@ti.com>
+ * Lesly A M <x0080970@ti.com>
+ *
+ * Copyright (C) 2008 Nokia Corporation
+ * Kalle Jokiniemi
+ *
+ * Copyright (C) 2010 Texas Instruments, Inc.
+ * Thara Gopinath <thara@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/debugfs.h>
+#include <linux/slab.h>
+
+#include <plat/common.h>
+#include <plat/voltage.h>
+
+#include "prm-regbits-34xx.h"
+
+#define VP_IDLE_TIMEOUT 200
+#define VP_TRANXDONE_TIMEOUT 300
+#define VOLTAGE_DIR_SIZE 16
+
+static struct dentry *voltage_dir;
+/* PRM voltage module */
+static u32 volt_mod;
+
+/* Voltage processor register offsets */
+struct vp_reg_offs {
+ u8 vpconfig;
+ u8 vstepmin;
+ u8 vstepmax;
+ u8 vlimitto;
+ u8 vstatus;
+ u8 voltage;
+};
+
+/* Voltage Processor bit field values, shifts and masks */
+struct vp_reg_val {
+ /* VPx_VPCONFIG */
+ u32 vpconfig_erroroffset;
+ u16 vpconfig_errorgain;
+ u32 vpconfig_errorgain_mask;
+ u8 vpconfig_errorgain_shift;
+ u32 vpconfig_initvoltage_mask;
+ u8 vpconfig_initvoltage_shift;
+ u32 vpconfig_timeouten;
+ u32 vpconfig_initvdd;
+ u32 vpconfig_forceupdate;
+ u32 vpconfig_vpenable;
+ /* VPx_VSTEPMIN */
+ u8 vstepmin_stepmin;
+ u16 vstepmin_smpswaittimemin;
+ u8 vstepmin_stepmin_shift;
+ u8 vstepmin_smpswaittimemin_shift;
+ /* VPx_VSTEPMAX */
+ u8 vstepmax_stepmax;
+ u16 vstepmax_smpswaittimemax;
+ u8 vstepmax_stepmax_shift;
+ u8 vstepmax_smpswaittimemax_shift;
+ /* VPx_VLIMITTO */
+ u16 vlimitto_vddmin;
+ u16 vlimitto_vddmax;
+ u16 vlimitto_timeout;
+ u16 vlimitto_vddmin_shift;
+ u16 vlimitto_vddmax_shift;
+ u16 vlimitto_timeout_shift;
+ /* PRM_IRQSTATUS*/
+ u32 tranxdone_status;
+};
+
+/**
+ * omap_vdd_info - Per Voltage Domain info
+ *
+ * @volt_data : voltage table having the distinct voltages supported
+ * by the domain and other associated per voltage data.
+ * @vp_offs : structure containing the offsets for various
+ * vp registers
+ * @vp_reg : the register values, shifts, masks for various
+ * vp registers
+ * @voltdm : pointer to the voltage domain structure
+ * @debug_dir : debug directory for this voltage domain.
+ * @volt_data_count : number of distinct voltages supported by this vdd.
+ * @nominal_volt : nominal voltage for this vdd.
+ * @curr_volt : current voltage for this vdd;
+ * cmdval_reg : voltage controller cmdval register.
+ * @vdd_sr_reg : the smartreflex register associated with this VDD.
+ */
+struct omap_vdd_info{
+ struct omap_volt_data *volt_data;
+ struct vp_reg_offs vp_offs;
+ struct vp_reg_val vp_reg;
+ struct voltagedomain voltdm;
+ struct dentry *debug_dir;
+ int volt_data_count;
+ u32 nominal_volt;
+ u32 curr_volt;
+ u8 cmdval_reg;
+ u8 vdd_sr_reg;
+};
+
+static struct omap_vdd_info *vdd_info;
+/*
+ * Number of scalable voltage domains.
+ */
+static int nr_scalable_vdd;
+
+/* OMAP3 VDD sturctures */
+static struct omap_vdd_info omap3_vdd_info[] = {
+ {
+ .vp_offs = {
+ .vpconfig = OMAP3_PRM_VP1_CONFIG_OFFSET,
+ .vstepmin = OMAP3_PRM_VP1_VSTEPMIN_OFFSET,
+ .vstepmax = OMAP3_PRM_VP1_VSTEPMAX_OFFSET,
+ .vlimitto = OMAP3_PRM_VP1_VLIMITTO_OFFSET,
+ .vstatus = OMAP3_PRM_VP1_STATUS_OFFSET,
+ .voltage = OMAP3_PRM_VP1_VOLTAGE_OFFSET,
+ },
+ .voltdm = {
+ .name = "mpu",
+ },
+ },
+ {
+ .vp_offs = {
+ .vpconfig = OMAP3_PRM_VP2_CONFIG_OFFSET,
+ .vstepmin = OMAP3_PRM_VP2_VSTEPMIN_OFFSET,
+ .vstepmax = OMAP3_PRM_VP2_VSTEPMAX_OFFSET,
+ .vlimitto = OMAP3_PRM_VP2_VLIMITTO_OFFSET,
+ .vstatus = OMAP3_PRM_VP2_STATUS_OFFSET,
+ .voltage = OMAP3_PRM_VP2_VOLTAGE_OFFSET,
+ },
+ .voltdm = {
+ .name = "core",
+ },
+ },
+};
+
+#define OMAP3_NR_SCALABLE_VDD ARRAY_SIZE(omap3_vdd_info)
+
+/* TODO: OMAP4 register offsets */
+
+/*
+ * Default voltage controller settings.
+ */
+static struct omap_volt_vc_data vc_config = {
+ .clksetup = 0xff,
+ .voltsetup_time1 = 0xfff,
+ .voltsetup_time2 = 0xfff,
+ .voltoffset = 0xff,
+ .voltsetup2 = 0xff,
+ .vdd0_on = 0x30, /* 1.2v */
+ .vdd0_onlp = 0x20, /* 1.0v */
+ .vdd0_ret = 0x1e, /* 0.975v */
+ .vdd0_off = 0x00, /* 0.6v */
+ .vdd1_on = 0x2c, /* 1.15v */
+ .vdd1_onlp = 0x20, /* 1.0v */
+ .vdd1_ret = 0x1e, /* .975v */
+ .vdd1_off = 0x00, /* 0.6v */
+};
+
+/*
+ * Default PMIC Data
+ */
+static struct omap_volt_pmic_info volt_pmic_info = {
+ .slew_rate = 4000,
+ .step_size = 12500,
+};
+
+/*
+ * Structures containing OMAP3430/OMAP3630 voltage supported and various
+ * data associated with it per voltage domain basis. Smartreflex Ntarget
+ * values are left as 0 as they have to be populated by smartreflex
+ * driver after reading the efuse.
+ */
+
+/* VDD1 */
+static struct omap_volt_data omap34xx_vdd1_volt_data[] = {
+ {.volt_nominal = 975000, .sr_errminlimit = 0xF4, .vp_errgain = 0x0C},
+ {.volt_nominal = 1075000, .sr_errminlimit = 0xF4, .vp_errgain = 0x0C},
+ {.volt_nominal = 1200000, .sr_errminlimit = 0xF9, .vp_errgain = 0x18},
+ {.volt_nominal = 1270000, .sr_errminlimit = 0xF9, .vp_errgain = 0x18},
+ {.volt_nominal = 1350000, .sr_errminlimit = 0xF9, .vp_errgain = 0x18},
+};
+
+static struct omap_volt_data omap36xx_vdd1_volt_data[] = {
+ {.volt_nominal = 930000, .sr_errminlimit = 0xF4, .vp_errgain = 0x0C},
+ {.volt_nominal = 1100000, .sr_errminlimit = 0xF9, .vp_errgain = 0x16},
+ {.volt_nominal = 1260000, .sr_errminlimit = 0xFA, .vp_errgain = 0x23},
+ {.volt_nominal = 1350000, .sr_errminlimit = 0xFA, .vp_errgain = 0x27},
+};
+
+/* VDD2 */
+static struct omap_volt_data omap34xx_vdd2_volt_data[] = {
+ {.volt_nominal = 975000, .sr_errminlimit = 0xF4, .vp_errgain = 0x0C},
+ {.volt_nominal = 1050000, .sr_errminlimit = 0xF4, .vp_errgain = 0x0C},
+ {.volt_nominal = 1150000, .sr_errminlimit = 0xF9, .vp_errgain = 0x18},
+};
+
+static struct omap_volt_data omap36xx_vdd2_volt_data[] = {
+ {.volt_nominal = 930000, .sr_errminlimit = 0xF4, .vp_errgain = 0x0C},
+ {.volt_nominal = 1137500, .sr_errminlimit = 0xF9, .vp_errgain = 0x16},
+};
+
+
+/* By default VPFORCEUPDATE is the chosen method of voltage scaling */
+static bool voltscale_vpforceupdate = true;
+
+static inline u32 voltage_read_reg(u8 offset)
+{
+ return prm_read_mod_reg(volt_mod, offset);
+}
+
+static inline void voltage_write_reg(u8 offset, u32 value)
+{
+ prm_write_mod_reg(value, volt_mod, offset);
+}
+
+static void vp_latch_vsel(struct omap_vdd_info *vdd)
+{
+ u32 vpconfig;
+ unsigned long uvdc;
+ char vsel;
+
+ uvdc = omap_voltage_get_nom_volt(&vdd->voltdm);
+ if (!uvdc) {
+ pr_warning("%s: unable to find current voltage for vdd_%s\n",
+ __func__, vdd->voltdm.name);
+ return;
+ }
+
+ if (!volt_pmic_info.uv_to_vsel) {
+ pr_warning("%s: PMIC function to convert voltage in uV to"
+ " vsel not registered\n", __func__);
+ return;
+ }
+
+ vsel = volt_pmic_info.uv_to_vsel(uvdc);
+
+ vpconfig = voltage_read_reg(vdd->vp_offs.vpconfig);
+ vpconfig &= ~(vdd->vp_reg.vpconfig_initvoltage_mask |
+ vdd->vp_reg.vpconfig_initvdd);
+ vpconfig |= vsel << vdd->vp_reg.vpconfig_initvoltage_shift;
+
+ voltage_write_reg(vdd->vp_offs.vpconfig, vpconfig);
+
+ /* Trigger initVDD value copy to voltage processor */
+ voltage_write_reg(vdd->vp_offs.vpconfig,
+ (vpconfig | vdd->vp_reg.vpconfig_initvdd));
+
+ /* Clear initVDD copy trigger bit */
+ voltage_write_reg(vdd->vp_offs.vpconfig, vpconfig);
+}
+
+/* OMAP3 specific voltage init functions */
+/*
+ * Intializes the voltage controller registers with the PMIC and board
+ * specific parameters and voltage setup times for OMAP3. If the board
+ * file does not populate the voltage controller parameters through
+ * omap3_pm_init_vc, default values specified in vc_config is used.
+ */
+static void __init omap3_init_voltagecontroller(void)
+{
+ voltage_write_reg(OMAP3_PRM_VC_SMPS_SA_OFFSET,
+ (OMAP3_SRI2C_SLAVE_ADDR <<
+ OMAP3430_PRM_VC_SMPS_SA_SA1_SHIFT) |
+ (OMAP3_SRI2C_SLAVE_ADDR <<
+ OMAP3430_PRM_VC_SMPS_SA_SA0_SHIFT));
+ voltage_write_reg(OMAP3_PRM_VC_SMPS_VOL_RA_OFFSET,
+ (OMAP3_VDD2_SR_CONTROL_REG << OMAP3430_VOLRA1_SHIFT) |
+ (OMAP3_VDD1_SR_CONTROL_REG << OMAP3430_VOLRA0_SHIFT));
+ voltage_write_reg(OMAP3_PRM_VC_CMD_VAL_0_OFFSET,
+ (vc_config.vdd0_on << OMAP3430_VC_CMD_ON_SHIFT) |
+ (vc_config.vdd0_onlp << OMAP3430_VC_CMD_ONLP_SHIFT) |
+ (vc_config.vdd0_ret << OMAP3430_VC_CMD_RET_SHIFT) |
+ (vc_config.vdd0_off << OMAP3430_VC_CMD_OFF_SHIFT));
+ voltage_write_reg(OMAP3_PRM_VC_CMD_VAL_1_OFFSET,
+ (vc_config.vdd1_on << OMAP3430_VC_CMD_ON_SHIFT) |
+ (vc_config.vdd1_onlp << OMAP3430_VC_CMD_ONLP_SHIFT) |
+ (vc_config.vdd1_ret << OMAP3430_VC_CMD_RET_SHIFT) |
+ (vc_config.vdd1_off << OMAP3430_VC_CMD_OFF_SHIFT));
+ voltage_write_reg(OMAP3_PRM_VC_CH_CONF_OFFSET,
+ OMAP3430_CMD1_MASK | OMAP3430_RAV1_MASK);
+ voltage_write_reg(OMAP3_PRM_VC_I2C_CFG_OFFSET,
+ OMAP3430_MCODE_SHIFT | OMAP3430_HSEN_MASK);
+
+ /* Write setup times */
+ voltage_write_reg(OMAP3_PRM_CLKSETUP_OFFSET, vc_config.clksetup);
+ voltage_write_reg(OMAP3_PRM_VOLTSETUP1_OFFSET,
+ (vc_config.voltsetup_time2 <<
+ OMAP3430_SETUP_TIME2_SHIFT) |
+ (vc_config.voltsetup_time1 <<
+ OMAP3430_SETUP_TIME1_SHIFT));
+ voltage_write_reg(OMAP3_PRM_VOLTOFFSET_OFFSET, vc_config.voltoffset);
+ voltage_write_reg(OMAP3_PRM_VOLTSETUP2_OFFSET, vc_config.voltsetup2);
+}
+
+/* Sets up all the VDD related info for OMAP3 */
+static void __init omap3_vdd_data_configure(struct omap_vdd_info *vdd)
+{
+ struct clk *sys_ck;
+ u32 sys_clk_speed, timeout_val, waittime;
+
+ if (!strcmp(vdd->voltdm.name, "mpu")) {
+ if (cpu_is_omap3630()) {
+ vdd->vp_reg.vlimitto_vddmin =
+ OMAP3630_VP1_VLIMITTO_VDDMIN;
+ vdd->vp_reg.vlimitto_vddmax =
+ OMAP3630_VP1_VLIMITTO_VDDMAX;
+ vdd->volt_data = omap36xx_vdd1_volt_data;
+ vdd->volt_data_count =
+ ARRAY_SIZE(omap36xx_vdd1_volt_data);
+ } else {
+ vdd->vp_reg.vlimitto_vddmin =
+ OMAP3430_VP1_VLIMITTO_VDDMIN;
+ vdd->vp_reg.vlimitto_vddmax =
+ OMAP3430_VP1_VLIMITTO_VDDMAX;
+ vdd->volt_data = omap34xx_vdd1_volt_data;
+ vdd->volt_data_count =
+ ARRAY_SIZE(omap34xx_vdd1_volt_data);
+ }
+
+ vdd->vp_reg.tranxdone_status = OMAP3430_VP1_TRANXDONE_ST_MASK;
+ vdd->cmdval_reg = OMAP3_PRM_VC_CMD_VAL_0_OFFSET;
+ vdd->vdd_sr_reg = OMAP3_VDD1_SR_CONTROL_REG;
+ } else if (!strcmp(vdd->voltdm.name, "core")) {
+ if (cpu_is_omap3630()) {
+ vdd->vp_reg.vlimitto_vddmin =
+ OMAP3630_VP2_VLIMITTO_VDDMIN;
+ vdd->vp_reg.vlimitto_vddmax =
+ OMAP3630_VP2_VLIMITTO_VDDMAX;
+ vdd->volt_data = omap36xx_vdd2_volt_data;
+ vdd->volt_data_count =
+ ARRAY_SIZE(omap36xx_vdd2_volt_data);
+ } else {
+ vdd->vp_reg.vlimitto_vddmin =
+ OMAP3430_VP2_VLIMITTO_VDDMIN;
+ vdd->vp_reg.vlimitto_vddmax =
+ OMAP3430_VP2_VLIMITTO_VDDMAX;
+ vdd->volt_data = omap34xx_vdd2_volt_data;
+ vdd->volt_data_count =
+ ARRAY_SIZE(omap34xx_vdd2_volt_data);
+ }
+
+ vdd->vp_reg.tranxdone_status = OMAP3430_VP2_TRANXDONE_ST_MASK;
+ vdd->cmdval_reg = OMAP3_PRM_VC_CMD_VAL_1_OFFSET;
+ vdd->vdd_sr_reg = OMAP3_VDD2_SR_CONTROL_REG;
+ } else {
+ pr_warning("%s: vdd_%s does not exisit in OMAP3\n",
+ __func__, vdd->voltdm.name);
+ return;
+ }
+
+ /*
+ * Sys clk rate is require to calculate vp timeout value and
+ * smpswaittimemin and smpswaittimemax.
+ */
+ sys_ck = clk_get(NULL, "sys_ck");
+ if (IS_ERR(sys_ck)) {
+ pr_warning("%s: Could not get the sys clk to calculate"
+ "various vdd_%s params\n", __func__, vdd->voltdm.name);
+ return;
+ }
+ sys_clk_speed = clk_get_rate(sys_ck);
+ clk_put(sys_ck);
+ /* Divide to avoid overflow */
+ sys_clk_speed /= 1000;
+
+ /* Nominal/Reset voltage of the VDD */
+ vdd->nominal_volt = vdd->curr_volt = 1200000;
+
+ /* VPCONFIG bit fields */
+ vdd->vp_reg.vpconfig_erroroffset = (OMAP3_VP_CONFIG_ERROROFFSET <<
+ OMAP3430_ERROROFFSET_SHIFT);
+ vdd->vp_reg.vpconfig_errorgain_mask = OMAP3430_ERRORGAIN_MASK;
+ vdd->vp_reg.vpconfig_errorgain_shift = OMAP3430_ERRORGAIN_SHIFT;
+ vdd->vp_reg.vpconfig_initvoltage_shift = OMAP3430_INITVOLTAGE_SHIFT;
+ vdd->vp_reg.vpconfig_initvoltage_mask = OMAP3430_INITVOLTAGE_MASK;
+ vdd->vp_reg.vpconfig_timeouten = OMAP3430_TIMEOUTEN_MASK;
+ vdd->vp_reg.vpconfig_initvdd = OMAP3430_INITVDD_MASK;
+ vdd->vp_reg.vpconfig_forceupdate = OMAP3430_FORCEUPDATE_MASK;
+ vdd->vp_reg.vpconfig_vpenable = OMAP3430_VPENABLE_MASK;
+
+ /* VSTEPMIN VSTEPMAX bit fields */
+ waittime = ((volt_pmic_info.step_size / volt_pmic_info.slew_rate) *
+ sys_clk_speed) / 1000;
+ vdd->vp_reg.vstepmin_smpswaittimemin = waittime;
+ vdd->vp_reg.vstepmax_smpswaittimemax = waittime;
+ vdd->vp_reg.vstepmin_stepmin = OMAP3_VP_VSTEPMIN_VSTEPMIN;
+ vdd->vp_reg.vstepmax_stepmax = OMAP3_VP_VSTEPMAX_VSTEPMAX;
+ vdd->vp_reg.vstepmin_smpswaittimemin_shift =
+ OMAP3430_SMPSWAITTIMEMIN_SHIFT;
+ vdd->vp_reg.vstepmax_smpswaittimemax_shift =
+ OMAP3430_SMPSWAITTIMEMAX_SHIFT;
+ vdd->vp_reg.vstepmin_stepmin_shift = OMAP3430_VSTEPMIN_SHIFT;
+ vdd->vp_reg.vstepmax_stepmax_shift = OMAP3430_VSTEPMAX_SHIFT;
+
+ /* VLIMITTO bit fields */
+ timeout_val = (sys_clk_speed * OMAP3_VP_VLIMITTO_TIMEOUT_US) / 1000;
+ vdd->vp_reg.vlimitto_timeout = timeout_val;
+ vdd->vp_reg.vlimitto_vddmin_shift = OMAP3430_VDDMIN_SHIFT;
+ vdd->vp_reg.vlimitto_vddmax_shift = OMAP3430_VDDMAX_SHIFT;
+ vdd->vp_reg.vlimitto_timeout_shift = OMAP3430_TIMEOUT_SHIFT;
+}
+
+/* Generic voltage init functions */
+static void __init init_voltageprocessor(struct omap_vdd_info *vdd)
+{
+ u32 vpconfig;
+
+ vpconfig = vdd->vp_reg.vpconfig_erroroffset |
+ (vdd->vp_reg.vpconfig_errorgain <<
+ vdd->vp_reg.vpconfig_errorgain_shift) |
+ vdd->vp_reg.vpconfig_timeouten;
+
+ voltage_write_reg(vdd->vp_offs.vpconfig, vpconfig);
+
+ voltage_write_reg(vdd->vp_offs.vstepmin,
+ (vdd->vp_reg.vstepmin_smpswaittimemin <<
+ vdd->vp_reg.vstepmin_smpswaittimemin_shift) |
+ (vdd->vp_reg.vstepmin_stepmin <<
+ vdd->vp_reg.vstepmin_stepmin_shift));
+
+ voltage_write_reg(vdd->vp_offs.vstepmax,
+ (vdd->vp_reg.vstepmax_smpswaittimemax <<
+ vdd->vp_reg.vstepmax_smpswaittimemax_shift) |
+ (vdd->vp_reg.vstepmax_stepmax <<
+ vdd->vp_reg.vstepmax_stepmax_shift));
+
+ voltage_write_reg(vdd->vp_offs.vlimitto,
+ (vdd->vp_reg.vlimitto_vddmax <<
+ vdd->vp_reg.vlimitto_vddmax_shift) |
+ (vdd->vp_reg.vlimitto_vddmin <<
+ vdd->vp_reg.vlimitto_vddmin_shift) |
+ (vdd->vp_reg.vlimitto_timeout <<
+ vdd->vp_reg.vlimitto_timeout_shift));
+}
+
+static void __init vdd_debugfs_init(struct omap_vdd_info *vdd)
+{
+ char *name;
+
+ name = kzalloc(VOLTAGE_DIR_SIZE, GFP_KERNEL);
+ if (!name) {
+ pr_warning("%s: Unable to allocate memry for debugfs"
+ "directory name for vdd_%s",
+ __func__, vdd->voltdm.name);
+ return;
+ }
+ strcpy(name, "vdd_");
+ strcat(name, vdd->voltdm.name);
+
+ vdd->debug_dir = debugfs_create_dir(name, voltage_dir);
+ if (IS_ERR(vdd->debug_dir)) {
+ pr_warning("%s: Unable to create debugfs directory for"
+ "vdd_%s\n", __func__, vdd->voltdm.name);
+ vdd->debug_dir = NULL;
+ }
+}
+
+/* vc_bypass_scale_voltage - VC bypass method of voltage scaling */
+static int vc_bypass_scale_voltage(struct omap_vdd_info *vdd,
+ unsigned long target_volt)
+{
+ struct omap_volt_data *volt_data;
+ u32 vc_bypass_value, vc_cmdval, vc_valid, vc_bypass_val_reg_offs;
+ u32 vp_errgain_val, vc_cmd_on_mask;
+ u32 loop_cnt = 0, retries_cnt = 0;
+ u32 smps_steps = 0, smps_delay = 0;
+ u8 vc_data_shift, vc_slaveaddr_shift, vc_regaddr_shift;
+ u8 vc_cmd_on_shift;
+ u8 target_vsel, current_vsel, sr_i2c_slave_addr;
+
+ if (cpu_is_omap34xx()) {
+ vc_cmd_on_shift = OMAP3430_VC_CMD_ON_SHIFT;
+ vc_cmd_on_mask = OMAP3430_VC_CMD_ON_MASK;
+ vc_data_shift = OMAP3430_DATA_SHIFT;
+ vc_slaveaddr_shift = OMAP3430_SLAVEADDR_SHIFT;
+ vc_regaddr_shift = OMAP3430_REGADDR_SHIFT;
+ vc_valid = OMAP3430_VALID_MASK;
+ vc_bypass_val_reg_offs = OMAP3_PRM_VC_BYPASS_VAL_OFFSET;
+ sr_i2c_slave_addr = OMAP3_SRI2C_SLAVE_ADDR;
+ } else {
+ pr_warning("%s: Voltage scaling not yet enabled for"
+ "this chip\n", __func__);
+ return -EINVAL;
+ }
+
+ /* Get volt_data corresponding to target_volt */
+ volt_data = omap_voltage_get_voltdata(&vdd->voltdm, target_volt);
+ if (IS_ERR(volt_data)) {
+ /*
+ * If a match is not found but the target voltage is
+ * is the nominal vdd voltage allow scaling
+ */
+ if (target_volt != vdd->nominal_volt) {
+ pr_warning("%s: Unable to get volt table for vdd_%s"
+ "during voltage scaling. Some really Wrong!",
+ __func__, vdd->voltdm.name);
+ return -ENODATA;
+ }
+ volt_data = NULL;
+ }
+
+ if (!volt_pmic_info.uv_to_vsel) {
+ pr_warning("%s: PMIC function to convert voltage in uV to"
+ "vsel not registered. Hence unable to scale voltage"
+ "for vdd_%s\n", __func__, vdd->voltdm.name);
+ return -ENODATA;
+ }
+
+ target_vsel = volt_pmic_info.uv_to_vsel(target_volt);
+ current_vsel = voltage_read_reg(vdd->vp_offs.voltage);
+ smps_steps = abs(target_vsel - current_vsel);
+
+ /* Setting the ON voltage to the new target voltage */
+ vc_cmdval = voltage_read_reg(vdd->cmdval_reg);
+ vc_cmdval &= ~vc_cmd_on_mask;
+ vc_cmdval |= (target_vsel << vc_cmd_on_shift);
+ voltage_write_reg(vdd->cmdval_reg, vc_cmdval);
+
+ /* Setting vp errorgain based on the voltage */
+ if (volt_data) {
+ vp_errgain_val = voltage_read_reg(vdd->vp_offs.vpconfig);
+ vdd->vp_reg.vpconfig_errorgain = volt_data->vp_errgain;
+ vp_errgain_val &= ~vdd->vp_reg.vpconfig_errorgain_mask;
+ vp_errgain_val |= vdd->vp_reg.vpconfig_errorgain <<
+ vdd->vp_reg.vpconfig_errorgain_shift;
+ voltage_write_reg(vdd->vp_offs.vpconfig, vp_errgain_val);
+ }
+
+ vc_bypass_value = (target_vsel << vc_data_shift) |
+ (vdd->vdd_sr_reg << vc_regaddr_shift) |
+ (sr_i2c_slave_addr << vc_slaveaddr_shift);
+
+ voltage_write_reg(vc_bypass_val_reg_offs, vc_bypass_value);
+
+ voltage_write_reg(vc_bypass_val_reg_offs, vc_bypass_value | vc_valid);
+ vc_bypass_value = voltage_read_reg(vc_bypass_val_reg_offs);
+
+ /*
+ * Loop till the bypass command is acknowledged from the SMPS.
+ * NOTE: This is legacy code. The loop count and retry count needs
+ * to be revisited.
+ */
+ while (!(vc_bypass_value & vc_valid)) {
+ loop_cnt++;
+
+ if (retries_cnt > 10) {
+ pr_warning("%s: Retry count exceeded\n", __func__);
+ return -ETIMEDOUT;
+ }
+
+ if (loop_cnt > 50) {
+ retries_cnt++;
+ loop_cnt = 0;
+ udelay(10);
+ }
+ vc_bypass_value = voltage_read_reg(vc_bypass_val_reg_offs);
+ }
+
+ /* SMPS slew rate / step size. 2us added as buffer. */
+ smps_delay = ((smps_steps * volt_pmic_info.step_size) /
+ volt_pmic_info.slew_rate) + 2;
+ udelay(smps_delay);
+
+ vdd->curr_volt = target_volt;
+
+ return 0;
+}
+
+/* VP force update method of voltage scaling */
+static int vp_forceupdate_scale_voltage(struct omap_vdd_info *vdd,
+ unsigned long target_volt)
+{
+ struct omap_volt_data *volt_data;
+ u32 vc_cmd_on_mask, vc_cmdval, vpconfig;
+ u32 smps_steps = 0, smps_delay = 0;
+ int timeout = 0;
+ u8 target_vsel, current_vsel;
+ u8 vc_cmd_on_shift;
+ u8 prm_irqst_reg_offs, ocp_mod;
+
+ if (cpu_is_omap34xx()) {
+ vc_cmd_on_shift = OMAP3430_VC_CMD_ON_SHIFT;
+ vc_cmd_on_mask = OMAP3430_VC_CMD_ON_MASK;
+ prm_irqst_reg_offs = OMAP3_PRM_IRQSTATUS_MPU_OFFSET;
+ ocp_mod = OCP_MOD;
+ } else {
+ pr_warning("%s: Voltage scaling not yet enabled for"
+ "this chip\n", __func__);
+ return -EINVAL;
+ }
+
+ /* Get volt_data corresponding to the target_volt */
+ volt_data = omap_voltage_get_voltdata(&vdd->voltdm, target_volt);
+ if (IS_ERR(volt_data)) {
+ /*
+ * If a match is not found but the target voltage is
+ * is the nominal vdd voltage allow scaling
+ */
+ if (target_volt != vdd->nominal_volt) {
+ pr_warning("%s: Unable to get voltage table for vdd_%s"
+ "during voltage scaling. Some really Wrong!",
+ __func__, vdd->voltdm.name);
+ return -ENODATA;
+ }
+ volt_data = NULL;
+ }
+
+ if (!volt_pmic_info.uv_to_vsel) {
+ pr_warning("%s: PMIC function to convert voltage in uV to"
+ "vsel not registered. Hence unable to scale voltage"
+ "for vdd_%s\n", __func__, vdd->voltdm.name);
+ return -ENODATA;
+ }
+
+ target_vsel = volt_pmic_info.uv_to_vsel(target_volt);
+ current_vsel = voltage_read_reg(vdd->vp_offs.voltage);
+ smps_steps = abs(target_vsel - current_vsel);
+
+ /* Setting the ON voltage to the new target voltage */
+ vc_cmdval = voltage_read_reg(vdd->cmdval_reg);
+ vc_cmdval &= ~vc_cmd_on_mask;
+ vc_cmdval |= (target_vsel << vc_cmd_on_shift);
+ voltage_write_reg(vdd->cmdval_reg, vc_cmdval);
+
+ /* Getting vp errorgain based on the voltage */
+ if (volt_data)
+ vdd->vp_reg.vpconfig_errorgain =
+ volt_data->vp_errgain;
+
+ /*
+ * Clear all pending TransactionDone interrupt/status. Typical latency
+ * is <3us
+ */
+ while (timeout++ < VP_TRANXDONE_TIMEOUT) {
+ prm_write_mod_reg(vdd->vp_reg.tranxdone_status,
+ ocp_mod, prm_irqst_reg_offs);
+ if (!(prm_read_mod_reg(ocp_mod, prm_irqst_reg_offs) &
+ vdd->vp_reg.tranxdone_status))
+ break;
+ udelay(1);
+ }
+ if (timeout >= VP_TRANXDONE_TIMEOUT) {
+ pr_warning("%s: vdd_%s TRANXDONE timeout exceeded."
+ "Voltage change aborted", __func__, vdd->voltdm.name);
+ return -ETIMEDOUT;
+ }
+
+ /* Configure for VP-Force Update */
+ vpconfig = voltage_read_reg(vdd->vp_offs.vpconfig);
+ vpconfig &= ~(vdd->vp_reg.vpconfig_initvdd |
+ vdd->vp_reg.vpconfig_forceupdate |
+ vdd->vp_reg.vpconfig_initvoltage_mask |
+ vdd->vp_reg.vpconfig_errorgain_mask);
+ vpconfig |= ((target_vsel <<
+ vdd->vp_reg.vpconfig_initvoltage_shift) |
+ (vdd->vp_reg.vpconfig_errorgain <<
+ vdd->vp_reg.vpconfig_errorgain_shift));
+ voltage_write_reg(vdd->vp_offs.vpconfig, vpconfig);
+
+ /* Trigger initVDD value copy to voltage processor */
+ vpconfig |= vdd->vp_reg.vpconfig_initvdd;
+ voltage_write_reg(vdd->vp_offs.vpconfig, vpconfig);
+
+ /* Force update of voltage */
+ vpconfig |= vdd->vp_reg.vpconfig_forceupdate;
+ voltage_write_reg(vdd->vp_offs.vpconfig, vpconfig);
+
+ /*
+ * Wait for TransactionDone. Typical latency is <200us.
+ * Depends on SMPSWAITTIMEMIN/MAX and voltage change
+ */
+ timeout = 0;
+ omap_test_timeout((prm_read_mod_reg(ocp_mod, prm_irqst_reg_offs) &
+ vdd->vp_reg.tranxdone_status),
+ VP_TRANXDONE_TIMEOUT, timeout);
+ if (timeout >= VP_TRANXDONE_TIMEOUT)
+ pr_err("%s: vdd_%s TRANXDONE timeout exceeded."
+ "TRANXDONE never got set after the voltage update\n",
+ __func__, vdd->voltdm.name);
+
+ /*
+ * Wait for voltage to settle with SW wait-loop.
+ * SMPS slew rate / step size. 2us added as buffer.
+ */
+ smps_delay = ((smps_steps * volt_pmic_info.step_size) /
+ volt_pmic_info.slew_rate) + 2;
+ udelay(smps_delay);
+
+ /*
+ * Disable TransactionDone interrupt , clear all status, clear
+ * control registers
+ */
+ timeout = 0;
+ while (timeout++ < VP_TRANXDONE_TIMEOUT) {
+ prm_write_mod_reg(vdd->vp_reg.tranxdone_status,
+ ocp_mod, prm_irqst_reg_offs);
+ if (!(prm_read_mod_reg(ocp_mod, prm_irqst_reg_offs) &
+ vdd->vp_reg.tranxdone_status))
+ break;
+ udelay(1);
+ }
+ if (timeout >= VP_TRANXDONE_TIMEOUT)
+ pr_warning("%s: vdd_%s TRANXDONE timeout exceeded while trying"
+ "to clear the TRANXDONE status\n",
+ __func__, vdd->voltdm.name);
+
+ vpconfig = voltage_read_reg(vdd->vp_offs.vpconfig);
+ /* Clear initVDD copy trigger bit */
+ vpconfig &= ~vdd->vp_reg.vpconfig_initvdd;;
+ voltage_write_reg(vdd->vp_offs.vpconfig, vpconfig);
+ /* Clear force bit */
+ vpconfig &= ~vdd->vp_reg.vpconfig_forceupdate;
+ voltage_write_reg(vdd->vp_offs.vpconfig, vpconfig);
+
+ vdd->curr_volt = target_volt;
+
+ return 0;
+}
+
+/* Public functions */
+/**
+ * omap_voltage_get_nom_volt() - Gets the current non-auto-compensated voltage
+ * @voltdm: pointer to the VDD for which current voltage info is needed
+ *
+ * API to get the current non-auto-compensated voltage for a VDD.
+ * Returns 0 in case of error else returns the current voltage for the VDD.
+ */
+unsigned long omap_voltage_get_nom_volt(struct voltagedomain *voltdm)
+{
+ struct omap_vdd_info *vdd;
+
+ if (!voltdm || IS_ERR(voltdm)) {
+ pr_warning("%s: VDD specified does not exist!\n", __func__);
+ return 0;
+ }
+
+ vdd = container_of(voltdm, struct omap_vdd_info, voltdm);
+
+ return vdd->curr_volt;
+}
+
+/**
+ * omap_vp_get_curr_volt() - API to get the current vp voltage.
+ * @voltdm: pointer to the VDD.
+ *
+ * This API returns the current voltage for the specified voltage processor
+ */
+unsigned long omap_vp_get_curr_volt(struct voltagedomain *voltdm)
+{
+ struct omap_vdd_info *vdd;
+ u8 curr_vsel;
+
+ if (!voltdm || IS_ERR(voltdm)) {
+ pr_warning("%s: VDD specified does not exist!\n", __func__);
+ return 0;
+ }
+
+ vdd = container_of(voltdm, struct omap_vdd_info, voltdm);
+
+ curr_vsel = voltage_read_reg(vdd->vp_offs.voltage);
+
+ if (!volt_pmic_info.vsel_to_uv) {
+ pr_warning("%s: PMIC function to convert vsel to voltage"
+ "in uV not registerd\n", __func__);
+ return 0;
+ }
+
+ return volt_pmic_info.vsel_to_uv(curr_vsel);
+}
+
+/**
+ * omap_vp_enable() - API to enable a particular VP
+ * @voltdm: pointer to the VDD whose VP is to be enabled.
+ *
+ * This API enables a particular voltage processor. Needed by the smartreflex
+ * class drivers.
+ */
+void omap_vp_enable(struct voltagedomain *voltdm)
+{
+ struct omap_vdd_info *vdd;
+ u32 vpconfig;
+
+ if (!voltdm || IS_ERR(voltdm)) {
+ pr_warning("%s: VDD specified does not exist!\n", __func__);
+ return;
+ }
+
+ vdd = container_of(voltdm, struct omap_vdd_info, voltdm);
+
+ /* If VP is already enabled, do nothing. Return */
+ if (voltage_read_reg(vdd->vp_offs.vpconfig) &
+ vdd->vp_reg.vpconfig_vpenable)
+ return;
+ /*
+ * This latching is required only if VC bypass method is used for
+ * voltage scaling during dvfs.
+ */
+ if (!voltscale_vpforceupdate)
+ vp_latch_vsel(vdd);
+
+ /* Enable VP */
+ vpconfig = voltage_read_reg(vdd->vp_offs.vpconfig);
+ voltage_write_reg(vdd->vp_offs.vpconfig,
+ vpconfig | vdd->vp_reg.vpconfig_vpenable);
+}
+
+/**
+ * omap_vp_disable() - API to disable a particular VP
+ * @voltdm: pointer to the VDD whose VP is to be disabled.
+ *
+ * This API disables a particular voltage processor. Needed by the smartreflex
+ * class drivers.
+ */
+void omap_vp_disable(struct voltagedomain *voltdm)
+{
+ struct omap_vdd_info *vdd;
+ u32 vpconfig;
+ int timeout;
+
+ if (!voltdm || IS_ERR(voltdm)) {
+ pr_warning("%s: VDD specified does not exist!\n", __func__);
+ return;
+ }
+
+ vdd = container_of(voltdm, struct omap_vdd_info, voltdm);
+
+ /* If VP is already disabled, do nothing. Return */
+ if (!(voltage_read_reg(vdd->vp_offs.vpconfig) &
+ vdd->vp_reg.vpconfig_vpenable)) {
+ pr_warning("%s: Trying to disable VP for vdd_%s when"
+ "it is already disabled\n", __func__, voltdm->name);
+ return;
+ }
+
+ /* Disable VP */
+ vpconfig = voltage_read_reg(vdd->vp_offs.vpconfig);
+ vpconfig &= ~vdd->vp_reg.vpconfig_vpenable;
+ voltage_write_reg(vdd->vp_offs.vpconfig, vpconfig);
+
+ /*
+ * Wait for VP idle Typical latency is <2us. Maximum latency is ~100us
+ */
+ omap_test_timeout((voltage_read_reg(vdd->vp_offs.vstatus)),
+ VP_IDLE_TIMEOUT, timeout);
+
+ if (timeout >= VP_IDLE_TIMEOUT)
+ pr_warning("%s: vdd_%s idle timedout\n",
+ __func__, voltdm->name);
+ return;
+}
+
+/**
+ * omap_voltage_scale_vdd() - API to scale voltage of a particular
+ * voltage domain.
+ * @voltdm: pointer to the VDD which is to be scaled.
+ * @target_volt: The target voltage of the voltage domain
+ *
+ * This API should be called by the kernel to do the voltage scaling
+ * for a particular voltage domain during dvfs or any other situation.
+ */
+int omap_voltage_scale_vdd(struct voltagedomain *voltdm,
+ unsigned long target_volt)
+{
+ struct omap_vdd_info *vdd;
+
+ if (!voltdm || IS_ERR(voltdm)) {
+ pr_warning("%s: VDD specified does not exist!\n", __func__);
+ return -EINVAL;
+ }
+
+ vdd = container_of(voltdm, struct omap_vdd_info, voltdm);
+
+ if (voltscale_vpforceupdate)
+ return vp_forceupdate_scale_voltage(vdd, target_volt);
+ else
+ return vc_bypass_scale_voltage(vdd, target_volt);
+}
+
+
+
+/**
+ * omap_voltage_reset() - Resets the voltage of a particular voltage domain
+ * to that of the current OPP.
+ * @voltdm: pointer to the VDD whose voltage is to be reset.
+ *
+ * This API finds out the correct voltage the voltage domain is supposed
+ * to be at and resets the voltage to that level. Should be used expecially
+ * while disabling any voltage compensation modules.
+ */
+void omap_voltage_reset(struct voltagedomain *voltdm)
+{
+ unsigned long target_uvdc;
+
+ if (!voltdm || IS_ERR(voltdm)) {
+ pr_warning("%s: VDD specified does not exist!\n", __func__);
+ return;
+ }
+
+ target_uvdc = omap_voltage_get_nom_volt(voltdm);
+ if (!target_uvdc) {
+ pr_err("%s: unable to find current voltage for vdd_%s\n",
+ __func__, voltdm->name);
+ return;
+ }
+
+ omap_voltage_scale_vdd(voltdm, target_uvdc);
+}
+
+/**
+ * omap_change_voltscale_method() - API to change the voltage scaling method.
+ * @voltscale_method: the method to be used for voltage scaling.
+ *
+ * This API can be used by the board files to change the method of voltage
+ * scaling between vpforceupdate and vcbypass. The parameter values are
+ * defined in voltage.h
+ */
+void omap_change_voltscale_method(int voltscale_method)
+{
+ switch (voltscale_method) {
+ case VOLTSCALE_VPFORCEUPDATE:
+ voltscale_vpforceupdate = true;
+ return;
+ case VOLTSCALE_VCBYPASS:
+ voltscale_vpforceupdate = false;
+ return;
+ default:
+ pr_warning("%s: Trying to change the method of voltage scaling"
+ "to an unsupported one!\n", __func__);
+ }
+}
+
+/**
+ * omap_voltage_init_vc() - polpulates vc_config with values specified in
+ * board file
+ * @setup_vc: the structure with various vc parameters
+ *
+ * Updates vc_config with the voltage setup times and other parameters as
+ * specified in setup_vc. vc_config is later used in init_voltagecontroller
+ * to initialize the voltage controller registers. Board files should call
+ * this function with the correct volatge settings corresponding
+ * the particular PMIC and chip.
+ */
+void __init omap_voltage_init_vc(struct omap_volt_vc_data *setup_vc)
+{
+ if (!setup_vc)
+ return;
+
+ vc_config.clksetup = setup_vc->clksetup;
+ vc_config.voltsetup_time1 = setup_vc->voltsetup_time1;
+ vc_config.voltsetup_time2 = setup_vc->voltsetup_time2;
+ vc_config.voltoffset = setup_vc->voltoffset;
+ vc_config.voltsetup2 = setup_vc->voltsetup2;
+ vc_config.vdd0_on = setup_vc->vdd0_on;
+ vc_config.vdd0_onlp = setup_vc->vdd0_onlp;
+ vc_config.vdd0_ret = setup_vc->vdd0_ret;
+ vc_config.vdd0_off = setup_vc->vdd0_off;
+ vc_config.vdd1_on = setup_vc->vdd1_on;
+ vc_config.vdd1_onlp = setup_vc->vdd1_onlp;
+ vc_config.vdd1_ret = setup_vc->vdd1_ret;
+ vc_config.vdd1_off = setup_vc->vdd1_off;
+}
+
+/**
+ * omap_voltage_get_volttable() - API to get the voltage table associated with a
+ * particular voltage domain.
+ * @voltdm: pointer to the VDD for which the voltage table is required
+ * @volt_data: the voltage table for the particular vdd which is to be
+ * populated by this API
+ *
+ * This API populates the voltage table associated with a VDD into the
+ * passed parameter pointer. Returns the count of distinct voltages
+ * supported by this vdd.
+ *
+ */
+int omap_voltage_get_volttable(struct voltagedomain *voltdm,
+ struct omap_volt_data **volt_data)
+{
+ struct omap_vdd_info *vdd;
+
+ if (!voltdm || IS_ERR(voltdm)) {
+ pr_warning("%s: VDD specified does not exist!\n", __func__);
+ return 0;
+ }
+
+ vdd = container_of(voltdm, struct omap_vdd_info, voltdm);
+
+ *volt_data = vdd->volt_data;
+ return vdd->volt_data_count;
+}
+
+/**
+ * omap_voltage_get_voltdata() - API to get the voltage table entry for a
+ * particular voltage
+ * @voltdm: pointer to the VDD whose voltage table has to be searched
+ * @volt: the voltage to be searched in the voltage table
+ *
+ * This API searches through the voltage table for the required voltage
+ * domain and tries to find a matching entry for the passed voltage volt.
+ * If a matching entry is found volt_data is populated with that entry.
+ * This API searches only through the non-compensated voltages int the
+ * voltage table.
+ * Returns pointer to the voltage table entry corresponding to volt on
+ * sucess. Returns -ENODATA if no voltage table exisits for the passed voltage
+ * domain or if there is no matching entry.
+ */
+struct omap_volt_data *omap_voltage_get_voltdata(struct voltagedomain *voltdm,
+ unsigned long volt)
+{
+ struct omap_vdd_info *vdd;
+ int i;
+
+ if (!voltdm || IS_ERR(voltdm)) {
+ pr_warning("%s: VDD specified does not exist!\n", __func__);
+ return ERR_PTR(-EINVAL);
+ }
+
+ vdd = container_of(voltdm, struct omap_vdd_info, voltdm);
+
+ if (!vdd->volt_data) {
+ pr_warning("%s: voltage table does not exist for vdd_%s\n",
+ __func__, voltdm->name);
+ return ERR_PTR(-ENODATA);
+ }
+
+ for (i = 0; i < vdd->volt_data_count; i++) {
+ if (vdd->volt_data[i].volt_nominal == volt)
+ return &vdd->volt_data[i];
+ }
+
+ pr_notice("%s: Unable to match the current voltage with the voltage"
+ "table for vdd_%s\n", __func__, voltdm->name);
+
+ return ERR_PTR(-ENODATA);
+}
+
+/**
+ * omap_voltage_get_dbgdir() - API to get pointer to the debugfs directory
+ * corresponding to a voltage domain.
+ *
+ * @voltdm: pointer to the VDD whose debug directory is required.
+ *
+ * This API returns pointer to the debugfs directory corresponding
+ * to the voltage domain. Should be used by drivers requiring to
+ * add any debug entry for a particular voltage domain. Returns NULL
+ * in case of error.
+ */
+struct dentry *omap_voltage_get_dbgdir(struct voltagedomain *voltdm)
+{
+ struct omap_vdd_info *vdd;
+
+ if (!voltdm || IS_ERR(voltdm)) {
+ pr_warning("%s: VDD specified does not exist!\n", __func__);
+ return NULL;
+ }
+
+ vdd = container_of(voltdm, struct omap_vdd_info, voltdm);
+ return vdd->debug_dir;
+}
+
+/**
+ * omap_voltage_register_pmic() - API to register PMIC specific data
+ * @pmic_info: the structure containing pmic info
+ *
+ * This API is to be called by the borad file to specify the pmic specific
+ * info as present in omap_volt_pmic_info structure. A default pmic info
+ * table is maintained in the driver volt_pmic_info. If the board file do
+ * not override the default table using this API, the default values wiil
+ * be used in the driver.
+ */
+void omap_voltage_register_pmic(struct omap_volt_pmic_info *pmic_info)
+{
+ volt_pmic_info.slew_rate = pmic_info->slew_rate;
+ volt_pmic_info.step_size = pmic_info->step_size;
+ volt_pmic_info.vsel_to_uv = pmic_info->vsel_to_uv;
+ volt_pmic_info.uv_to_vsel = pmic_info->uv_to_vsel;
+}
+
+/**
+ * omap_voltage_domain_lookup() - API to get the voltage domain pointer
+ * @name: Name of the voltage domain
+ *
+ * This API looks up in the global vdd_info struct for the
+ * existence of voltage domain <name>. If it exists, the API returns
+ * a pointer to the voltage domain structure corresponding to the
+ * VDD<name>. Else retuns error pointer.
+ */
+struct voltagedomain *omap_voltage_domain_lookup(char *name)
+{
+ int i;
+
+ if (!vdd_info) {
+ pr_err("%s: Voltage driver init not yet happened.Faulting!\n",
+ __func__);
+ return ERR_PTR(-EINVAL);
+ }
+
+ if (!name) {
+ pr_err("%s: No name to get the votage domain!\n", __func__);
+ return ERR_PTR(-EINVAL);
+ }
+
+ for (i = 0; i < nr_scalable_vdd; i++) {
+ if (!(strcmp(name, vdd_info[i].voltdm.name)))
+ return &vdd_info[i].voltdm;
+ }
+
+ return ERR_PTR(-EINVAL);
+}
+
+/**
+ * omap_voltage_init : Volatage init API which does VP and VC init.
+ */
+static int __init omap_voltage_init(void)
+{
+ void (*init_voltagecontroller) (void);
+ void (*vdd_data_configure) (struct omap_vdd_info *vdd);
+ int i;
+
+ if (cpu_is_omap34xx()) {
+ volt_mod = OMAP3430_GR_MOD;
+ vdd_info = omap3_vdd_info;
+ nr_scalable_vdd = OMAP3_NR_SCALABLE_VDD;
+ init_voltagecontroller = omap3_init_voltagecontroller;
+ vdd_data_configure = omap3_vdd_data_configure;
+ } else {
+ pr_warning("%s: voltage driver support not added\n", __func__);
+ return 0;
+ }
+
+ voltage_dir = debugfs_create_dir("voltage", NULL);
+ if (IS_ERR(voltage_dir))
+ pr_err("%s: Unable to create voltage debugfs main dir\n",
+ __func__);
+
+ init_voltagecontroller();
+ for (i = 0; i < nr_scalable_vdd; i++) {
+ vdd_data_configure(&vdd_info[i]);
+ init_voltageprocessor(&vdd_info[i]);
+ vdd_debugfs_init(&vdd_info[i]);
+ }
+ return 0;
+}
+postcore_initcall(omap_voltage_init);
new file mode 100644
@@ -0,0 +1,141 @@
+/*
+ * OMAP Voltage Management Routines
+ *
+ * Author: Thara Gopinath <thara@ti.com>
+ *
+ * Copyright (C) 2009 Texas Instruments, Inc.
+ * Thara Gopinath <thara@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __ARCH_ARM_MACH_OMAP2_VOLTAGE_H
+#define __ARCH_ARM_MACH_OMAP2_VOLTAGE_H
+
+#define VOLTSCALE_VPFORCEUPDATE 1
+#define VOLTSCALE_VCBYPASS 2
+
+/* Voltage SR Parameters for OMAP3*/
+#define OMAP3_SRI2C_SLAVE_ADDR 0x12
+#define OMAP3_VDD1_SR_CONTROL_REG 0x00
+#define OMAP3_VDD2_SR_CONTROL_REG 0x01
+
+/*
+ * Omap3 VP register specific values. Maybe these need to come from
+ * board file or PMIC data structure
+ */
+#define OMAP3_VP_CONFIG_ERROROFFSET 0x00
+#define OMAP3_VP_VSTEPMIN_SMPSWAITTIMEMIN 0x3C
+#define OMAP3_VP_VSTEPMIN_VSTEPMIN 0x1
+#define OMAP3_VP_VSTEPMAX_SMPSWAITTIMEMAX 0x3C
+#define OMAP3_VP_VSTEPMAX_VSTEPMAX 0x04
+#define OMAP3_VP_VLIMITTO_TIMEOUT_US 0x200
+
+/*
+ * Omap3430 specific VP register values. Maybe these need to come from
+ * board file or PMIC data structure
+ */
+#define OMAP3430_VP1_VLIMITTO_VDDMIN 0x14
+#define OMAP3430_VP1_VLIMITTO_VDDMAX 0x42
+#define OMAP3430_VP2_VLIMITTO_VDDMAX 0x2C
+#define OMAP3430_VP2_VLIMITTO_VDDMIN 0x18
+
+/*
+ * Omap3630 specific VP register values. Maybe these need to come from
+ * board file or PMIC data structure
+ */
+#define OMAP3630_VP1_VLIMITTO_VDDMIN 0x18
+#define OMAP3630_VP1_VLIMITTO_VDDMAX 0x3C
+#define OMAP3630_VP2_VLIMITTO_VDDMIN 0x18
+#define OMAP3630_VP2_VLIMITTO_VDDMAX 0x30
+
+/* TODO OMAP4 VP register values if the same file is used for OMAP4*/
+
+/**
+ * struct voltagedomain - omap voltage domain global structure.
+ * @name: Name of the voltage domain which can be used as a unique
+ * identifier.
+ */
+struct voltagedomain {
+ char *name;
+};
+
+/* API to get the voltagedomain pointer */
+struct voltagedomain *omap_voltage_domain_lookup(char *name);
+
+/**
+ * struct omap_volt_data - Omap voltage specific data.
+ * @voltage_nominal: The possible voltage value in uV
+ * @sr_nvalue: Smartreflex N target value at voltage <voltage>
+ * @sr_errminlimit: Error min limit value for smartreflex. This value
+ * differs at differnet opp and thus is linked
+ * with voltage.
+ * @vp_errorgain: Error gain value for the voltage processor. This
+ * field also differs according to the voltage/opp.
+ */
+struct omap_volt_data {
+ u32 volt_nominal;
+ u32 sr_nvalue;
+ u8 sr_errminlimit;
+ u8 vp_errgain;
+};
+
+/**
+ * struct omap_volt_pmic_info - PMIC specific data required by voltage driver.
+ * @slew_rate: PMIC slew rate (in uv/us)
+ * @step_size: PMIC voltage step size (in uv)
+ * @vsel_to_uv: PMIC API to convert vsel value to actual voltage in uV.
+ * @uv_to_vsel: PMIC API to convert voltage in uV to vsel value.
+ */
+struct omap_volt_pmic_info {
+ int slew_rate;
+ int step_size;
+ unsigned long (*vsel_to_uv) (const u8 vsel);
+ u8 (*uv_to_vsel) (unsigned long uV);
+};
+
+/* Various voltage controller related info */
+struct omap_volt_vc_data {
+ u16 clksetup;
+ u16 voltsetup_time1;
+ u16 voltsetup_time2;
+ u16 voltoffset;
+ u16 voltsetup2;
+ /* PRM_VC_CMD_VAL_0 specific bits */
+ u16 vdd0_on;
+ u16 vdd0_onlp;
+ u16 vdd0_ret;
+ u16 vdd0_off;
+ /* PRM_VC_CMD_VAL_1 specific bits */
+ u16 vdd1_on;
+ u16 vdd1_onlp;
+ u16 vdd1_ret;
+ u16 vdd1_off;
+};
+
+unsigned long omap_vp_get_curr_volt(struct voltagedomain *voltdm);
+void omap_vp_enable(struct voltagedomain *voltdm);
+void omap_vp_disable(struct voltagedomain *voltdm);
+int omap_voltage_scale_vdd(struct voltagedomain *voltdm,
+ unsigned long target_volt);
+void omap_voltage_reset(struct voltagedomain *voltdm);
+int omap_voltage_get_volttable(struct voltagedomain *voltdm,
+ struct omap_volt_data **volt_data);
+struct omap_volt_data *omap_voltage_get_voltdata(struct voltagedomain *voltdm,
+ unsigned long volt);
+unsigned long omap_voltage_get_nom_volt(struct voltagedomain *voltdm);
+struct dentry *omap_voltage_get_dbgdir(struct voltagedomain *voltdm);
+#ifdef CONFIG_PM
+void omap_voltage_register_pmic(struct omap_volt_pmic_info *pmic_info);
+void omap_voltage_init_vc(struct omap_volt_vc_data *setup_vc);
+void omap_change_voltscale_method(int voltscale_method);
+#else
+static inline void omap_voltage_register_pmic
+ (struct omap_volt_pmic_info *pmic_info) {}
+static inline void omap_voltage_init_vc(struct omap_volt_vc_data *setup_vc) {}
+static inline void omap_change_voltscale_method(int voltscale_method) {}
+#endif
+
+#endif