@@ -653,11 +653,11 @@ static void enable_board_wakeup_source(void)
OMAP_WAKEUP_EN | OMAP_PIN_INPUT_PULLUP);
}
-static const struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
+static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
- .port_mode[0] = EHCI_HCD_OMAP_MODE_PHY,
- .port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
- .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+ .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
.phy_reset = true,
.reset_gpio_port[0] = 57,
@@ -816,7 +816,7 @@ static void __init omap_3430sdp_init(void)
board_flash_init(sdp_flash_partitions, chip_sel_3430);
sdp3430_display_init();
enable_board_wakeup_source();
- usb_ehci_init(&ehci_pdata);
+ usb_ehci_init(&usbhs_bdata);
}
MACHINE_START(OMAP_3430SDP, "OMAP3430 3430SDP board")
@@ -54,11 +54,11 @@ static void enable_board_wakeup_source(void)
OMAP_WAKEUP_EN | OMAP_PIN_INPUT_PULLUP);
}
-static const struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
+static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
- .port_mode[0] = EHCI_HCD_OMAP_MODE_PHY,
- .port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
- .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+ .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
.phy_reset = true,
.reset_gpio_port[0] = 126,
@@ -211,7 +211,7 @@ static void __init omap_sdp_init(void)
board_smc91x_init();
board_flash_init(sdp_flash_partitions, chip_sel_sdp);
enable_board_wakeup_source();
- usb_ehci_init(&ehci_pdata);
+ usb_ehci_init(&usbhs_bdata);
}
MACHINE_START(OMAP_3630SDP, "OMAP 3630SDP board")
@@ -251,10 +251,10 @@ static void __init omap_4430sdp_init_irq(void)
gic_init_irq();
}
-static const struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
- .port_mode[0] = EHCI_HCD_OMAP_MODE_PHY,
- .port_mode[1] = EHCI_HCD_OMAP_MODE_UNKNOWN,
- .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
+ .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED,
+ .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
.phy_reset = false,
.reset_gpio_port[0] = -EINVAL,
.reset_gpio_port[1] = -EINVAL,
@@ -584,7 +584,7 @@ static void __init omap_4430sdp_init(void)
else
gpio_direction_output(OMAP4SDP_MDM_PWR_EN_GPIO, 1);
- usb_ehci_init(&ehci_pdata);
+ usb_ehci_init(&usbhs_bdata);
usb_musb_init(&musb_board_data);
status = omap_ethernet_init();
@@ -59,10 +59,10 @@ static void __init am3517_crane_init_irq(void)
omap_init_irq();
}
-static struct ehci_hcd_omap_platform_data ehci_pdata __initdata = {
- .port_mode[0] = EHCI_HCD_OMAP_MODE_PHY,
- .port_mode[1] = EHCI_HCD_OMAP_MODE_UNKNOWN,
- .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+static struct usbhs_omap_board_data usbhs_bdata __initdata = {
+ .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED,
+ .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
.phy_reset = true,
.reset_gpio_port[0] = GPIO_USB_NRESET,
@@ -103,7 +103,7 @@ static void __init am3517_crane_init(void)
return;
}
- usb_ehci_init(&ehci_pdata);
+ usb_ehci_init(&usbhs_bdata);
}
MACHINE_START(CRANEBOARD, "AM3517/05 CRANEBOARD")
@@ -430,15 +430,15 @@ static __init void am3517_evm_musb_init(void)
usb_musb_init(&musb_board_data);
}
-static const struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
- .port_mode[0] = EHCI_HCD_OMAP_MODE_PHY,
+static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
+ .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
#if defined(CONFIG_PANEL_SHARP_LQ043T1DG01) || \
defined(CONFIG_PANEL_SHARP_LQ043T1DG01_MODULE)
- .port_mode[1] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+ .port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED,
#else
- .port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
+ .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
#endif
- .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+ .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
.phy_reset = true,
.reset_gpio_port[0] = 57,
@@ -502,7 +502,7 @@ static void __init am3517_evm_init(void)
/* Configure GPIO for EHCI port */
omap_mux_init_gpio(57, OMAP_PIN_OUTPUT);
- usb_ehci_init(&ehci_pdata);
+ usb_ehci_init(&usbhs_bdata);
am3517_evm_hecc_init(&am3517_evm_hecc_pdata);
/* DSS */
am3517_evm_display_init();
@@ -605,10 +605,10 @@ static struct omap2_hsmmc_info mmc[] = {
{} /* Terminator */
};
-static struct ehci_hcd_omap_platform_data ehci_pdata __initdata = {
- .port_mode[0] = EHCI_HCD_OMAP_MODE_PHY,
- .port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
- .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+static struct usbhs_omap_board_data usbhs_bdata __initdata = {
+ .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
.phy_reset = true,
.reset_gpio_port[0] = OMAP_MAX_GPIO_LINES + 6,
@@ -810,7 +810,7 @@ static void __init cm_t35_init(void)
cm_t35_init_display();
usb_musb_init(&musb_board_data);
- usb_ehci_init(&ehci_pdata);
+ usb_ehci_init(&usbhs_bdata);
}
MACHINE_START(CM_T35, "Compulab CM-T35")
@@ -167,10 +167,10 @@ static inline void cm_t3517_init_rtc(void) {}
#define HSUSB2_RESET_GPIO (147)
#define USB_HUB_RESET_GPIO (152)
-static struct ehci_hcd_omap_platform_data cm_t3517_ehci_pdata __initdata = {
- .port_mode[0] = EHCI_HCD_OMAP_MODE_PHY,
- .port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
- .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+static struct usbhs_omap_board_data cm_t3517_ehci_pdata __initdata = {
+ .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
.phy_reset = true,
.reset_gpio_port[0] = HSUSB1_RESET_GPIO,
@@ -620,11 +620,11 @@ static struct omap_musb_board_data musb_board_data = {
.power = 100,
};
-static const struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
+static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
- .port_mode[0] = EHCI_HCD_OMAP_MODE_PHY,
- .port_mode[1] = EHCI_HCD_OMAP_MODE_UNKNOWN,
- .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+ .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED,
+ .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
.phy_reset = true,
.reset_gpio_port[0] = -EINVAL,
@@ -803,7 +803,7 @@ static void __init devkit8000_init(void)
devkit8000_ads7846_init();
usb_musb_init(&musb_board_data);
- usb_ehci_init(&ehci_pdata);
+ usb_ehci_init(&usbhs_bdata);
devkit8000_flash_init();
/* Ensure SDRC pins are mux'd for self-refresh */
@@ -627,10 +627,10 @@ static struct omap_musb_board_data musb_board_data = {
.power = 100,
};
-static const struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
- .port_mode[0] = EHCI_HCD_OMAP_MODE_PHY,
- .port_mode[1] = EHCI_HCD_OMAP_MODE_UNKNOWN,
- .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
+ .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED,
+ .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
.phy_reset = true,
.reset_gpio_port[0] = IGEP2_GPIO_USBH_NRESET,
@@ -699,7 +699,7 @@ static void __init igep2_init(void)
platform_add_devices(igep2_devices, ARRAY_SIZE(igep2_devices));
omap_serial_init();
usb_musb_init(&musb_board_data);
- usb_ehci_init(&ehci_pdata);
+ usb_ehci_init(&usbhs_bdata);
igep2_flash_init();
igep2_leds_init();
@@ -408,10 +408,10 @@ static void __init igep3_wifi_bt_init(void)
void __init igep3_wifi_bt_init(void) {}
#endif
-static const struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
- .port_mode[0] = EHCI_HCD_OMAP_MODE_UNKNOWN,
- .port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
- .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
+ .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
+ .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
.phy_reset = true,
.reset_gpio_port[0] = -EINVAL,
@@ -435,7 +435,7 @@ static void __init igep3_init(void)
platform_add_devices(igep3_devices, ARRAY_SIZE(igep3_devices));
omap_serial_init();
usb_musb_init(&musb_board_data);
- usb_ehci_init(&ehci_pdata);
+ usb_ehci_init(&usbhs_bdata);
igep3_flash_init();
igep3_leds_init();
@@ -586,11 +586,11 @@ static void __init omap3beagle_flash_init(void)
}
}
-static const struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
+static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
- .port_mode[0] = EHCI_HCD_OMAP_MODE_PHY,
- .port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
- .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+ .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
.phy_reset = true,
.reset_gpio_port[0] = -EINVAL,
@@ -625,7 +625,7 @@ static void __init omap3_beagle_init(void)
gpio_direction_output(170, true);
usb_musb_init(&musb_board_data);
- usb_ehci_init(&ehci_pdata);
+ usb_ehci_init(&usbhs_bdata);
omap3beagle_flash_init();
/* Ensure SDRC pins are mux'd for self-refresh */
@@ -638,11 +638,11 @@ static struct platform_device *omap3_evm_devices[] __initdata = {
&omap3_evm_dss_device,
};
-static struct ehci_hcd_omap_platform_data ehci_pdata __initdata = {
+static struct usbhs_omap_board_data usbhs_bdata __initdata = {
- .port_mode[0] = EHCI_HCD_OMAP_MODE_UNKNOWN,
- .port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
- .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+ .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
+ .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
.phy_reset = true,
/* PHY reset GPIO will be runtime programmed based on EVM version */
@@ -700,7 +700,7 @@ static void __init omap3_evm_init(void)
/* setup EHCI phy reset config */
omap_mux_init_gpio(21, OMAP_PIN_INPUT_PULLUP);
- ehci_pdata.reset_gpio_port[1] = 21;
+ usbhs_bdata.reset_gpio_port[1] = 21;
/* EVM REV >= E can supply 500mA with EXTVBUS programming */
musb_board_data.power = 500;
@@ -708,10 +708,10 @@ static void __init omap3_evm_init(void)
} else {
/* setup EHCI phy reset on MDC */
omap_mux_init_gpio(135, OMAP_PIN_OUTPUT);
- ehci_pdata.reset_gpio_port[1] = 135;
+ usbhs_bdata.reset_gpio_port[1] = 135;
}
usb_musb_init(&musb_board_data);
- usb_ehci_init(&ehci_pdata);
+ usb_ehci_init(&usbhs_bdata);
ads7846_dev_init();
omap3evm_init_smsc911x();
omap3_evm_display_init();
@@ -681,11 +681,11 @@ static struct platform_device *omap3pandora_devices[] __initdata = {
&pandora_vwlan_device,
};
-static const struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
+static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
- .port_mode[0] = EHCI_HCD_OMAP_MODE_PHY,
- .port_mode[1] = EHCI_HCD_OMAP_MODE_UNKNOWN,
- .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+ .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED,
+ .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
.phy_reset = true,
.reset_gpio_port[0] = 16,
@@ -716,7 +716,7 @@ static void __init omap3pandora_init(void)
spi_register_board_info(omap3pandora_spi_board_info,
ARRAY_SIZE(omap3pandora_spi_board_info));
omap3pandora_ads7846_init();
- usb_ehci_init(&ehci_pdata);
+ usb_ehci_init(&usbhs_bdata);
usb_musb_init(&musb_board_data);
gpmc_nand_init(&pandora_nand_data);
@@ -608,10 +608,10 @@ static struct platform_device *omap3_stalker_devices[] __initdata = {
&keys_gpio,
};
-static struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
- .port_mode[0] = EHCI_HCD_OMAP_MODE_UNKNOWN,
- .port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
- .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+static struct usbhs_omap_board_data usbhs_bdata __initconst = {
+ .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
+ .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
.phy_reset = true,
.reset_gpio_port[0] = -EINVAL,
@@ -649,7 +649,7 @@ static void __init omap3_stalker_init(void)
omap_serial_init();
usb_musb_init(&musb_board_data);
- usb_ehci_init(&ehci_pdata);
+ usb_ehci_init(&usbhs_bdata);
ads7846_dev_init();
omap_mux_init_gpio(21, OMAP_PIN_OUTPUT);
@@ -468,11 +468,11 @@ static void __init omap3touchbook_flash_init(void)
}
}
-static const struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
+static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
- .port_mode[0] = EHCI_HCD_OMAP_MODE_PHY,
- .port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
- .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+ .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
.phy_reset = true,
.reset_gpio_port[0] = -EINVAL,
@@ -527,7 +527,7 @@ static void __init omap3_touchbook_init(void)
ARRAY_SIZE(omap3_ads7846_spi_board_info));
omap3_ads7846_init();
usb_musb_init(&musb_board_data);
- usb_ehci_init(&ehci_pdata);
+ usb_ehci_init(&usbhs_bdata);
omap3touchbook_flash_init();
/* Ensure SDRC pins are mux'd for self-refresh */
@@ -83,10 +83,10 @@ static void __init omap4_panda_init_irq(void)
gic_init_irq();
}
-static const struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
- .port_mode[0] = EHCI_HCD_OMAP_MODE_PHY,
- .port_mode[1] = EHCI_HCD_OMAP_MODE_UNKNOWN,
- .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
+ .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED,
+ .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
.phy_reset = false,
.reset_gpio_port[0] = -EINVAL,
.reset_gpio_port[1] = -EINVAL,
@@ -128,7 +128,7 @@ static void __init omap4_ehci_init(void)
gpio_set_value(GPIO_HUB_NRESET, 0);
gpio_set_value(GPIO_HUB_NRESET, 1);
- usb_ehci_init(&ehci_pdata);
+ usb_ehci_init(&usbhs_bdata);
/* enable power to hub */
gpio_set_value(GPIO_HUB_POWER, 1);
@@ -423,10 +423,10 @@ static struct platform_device *overo_devices[] __initdata = {
&overo_lcd_device,
};
-static const struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
- .port_mode[0] = EHCI_HCD_OMAP_MODE_UNKNOWN,
- .port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
- .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
+ .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
+ .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
.phy_reset = true,
.reset_gpio_port[0] = -EINVAL,
@@ -454,7 +454,7 @@ static void __init overo_init(void)
omap_serial_init();
overo_flash_init();
usb_musb_init(&musb_board_data);
- usb_ehci_init(&ehci_pdata);
+ usb_ehci_init(&usbhs_bdata);
overo_ads7846_init();
overo_init_smsc911x();
@@ -106,10 +106,10 @@ static struct mtd_partition zoom_nand_partitions[] = {
},
};
-static const struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
- .port_mode[0] = EHCI_HCD_OMAP_MODE_UNKNOWN,
- .port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
- .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
+ .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
+ .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
.phy_reset = true,
.reset_gpio_port[0] = -EINVAL,
.reset_gpio_port[1] = ZOOM3_EHCI_RESET_GPIO,
@@ -123,7 +123,7 @@ static void __init omap_zoom_init(void)
} else if (machine_is_omap_zoom3()) {
omap3_mux_init(board_mux, OMAP_PACKAGE_CBP);
omap_mux_init_gpio(ZOOM3_EHCI_RESET_GPIO, OMAP_PIN_OUTPUT);
- usb_ehci_init(&ehci_pdata);
+ usb_ehci_init(&usbhs_bdata);
}
board_nand_init(zoom_nand_partitions,
@@ -64,10 +64,10 @@ static struct platform_device ehci_device = {
/*
* setup_ehci_io_mux - initialize IO pad mux for USBHOST
*/
-static void setup_ehci_io_mux(const enum ehci_hcd_omap_mode *port_mode)
+static void setup_ehci_io_mux(const enum usbhs_omap_port_mode *port_mode)
{
switch (port_mode[0]) {
- case EHCI_HCD_OMAP_MODE_PHY:
+ case OMAP_EHCI_PORT_MODE_PHY:
omap_mux_init_signal("hsusb1_stp", OMAP_PIN_OUTPUT);
omap_mux_init_signal("hsusb1_clk", OMAP_PIN_OUTPUT);
omap_mux_init_signal("hsusb1_dir", OMAP_PIN_INPUT_PULLDOWN);
@@ -81,7 +81,7 @@ static void setup_ehci_io_mux(const enum ehci_hcd_omap_mode *port_mode)
omap_mux_init_signal("hsusb1_data6", OMAP_PIN_INPUT_PULLDOWN);
omap_mux_init_signal("hsusb1_data7", OMAP_PIN_INPUT_PULLDOWN);
break;
- case EHCI_HCD_OMAP_MODE_TLL:
+ case OMAP_EHCI_PORT_MODE_TLL:
omap_mux_init_signal("hsusb1_tll_stp",
OMAP_PIN_INPUT_PULLUP);
omap_mux_init_signal("hsusb1_tll_clk",
@@ -107,14 +107,14 @@ static void setup_ehci_io_mux(const enum ehci_hcd_omap_mode *port_mode)
omap_mux_init_signal("hsusb1_tll_data7",
OMAP_PIN_INPUT_PULLDOWN);
break;
- case EHCI_HCD_OMAP_MODE_UNKNOWN:
+ case OMAP_USBHS_PORT_MODE_UNUSED:
/* FALLTHROUGH */
default:
break;
}
switch (port_mode[1]) {
- case EHCI_HCD_OMAP_MODE_PHY:
+ case OMAP_EHCI_PORT_MODE_PHY:
omap_mux_init_signal("hsusb2_stp", OMAP_PIN_OUTPUT);
omap_mux_init_signal("hsusb2_clk", OMAP_PIN_OUTPUT);
omap_mux_init_signal("hsusb2_dir", OMAP_PIN_INPUT_PULLDOWN);
@@ -136,7 +136,7 @@ static void setup_ehci_io_mux(const enum ehci_hcd_omap_mode *port_mode)
omap_mux_init_signal("hsusb2_data7",
OMAP_PIN_INPUT_PULLDOWN);
break;
- case EHCI_HCD_OMAP_MODE_TLL:
+ case OMAP_EHCI_PORT_MODE_TLL:
omap_mux_init_signal("hsusb2_tll_stp",
OMAP_PIN_INPUT_PULLUP);
omap_mux_init_signal("hsusb2_tll_clk",
@@ -162,17 +162,17 @@ static void setup_ehci_io_mux(const enum ehci_hcd_omap_mode *port_mode)
omap_mux_init_signal("hsusb2_tll_data7",
OMAP_PIN_INPUT_PULLDOWN);
break;
- case EHCI_HCD_OMAP_MODE_UNKNOWN:
+ case OMAP_USBHS_PORT_MODE_UNUSED:
/* FALLTHROUGH */
default:
break;
}
switch (port_mode[2]) {
- case EHCI_HCD_OMAP_MODE_PHY:
+ case OMAP_EHCI_PORT_MODE_PHY:
printk(KERN_WARNING "Port3 can't be used in PHY mode\n");
break;
- case EHCI_HCD_OMAP_MODE_TLL:
+ case OMAP_EHCI_PORT_MODE_TLL:
omap_mux_init_signal("hsusb3_tll_stp",
OMAP_PIN_INPUT_PULLUP);
omap_mux_init_signal("hsusb3_tll_clk",
@@ -198,7 +198,7 @@ static void setup_ehci_io_mux(const enum ehci_hcd_omap_mode *port_mode)
omap_mux_init_signal("hsusb3_tll_data7",
OMAP_PIN_INPUT_PULLDOWN);
break;
- case EHCI_HCD_OMAP_MODE_UNKNOWN:
+ case OMAP_USBHS_PORT_MODE_UNUSED:
/* FALLTHROUGH */
default:
break;
@@ -207,10 +207,10 @@ static void setup_ehci_io_mux(const enum ehci_hcd_omap_mode *port_mode)
return;
}
-static void setup_4430ehci_io_mux(const enum ehci_hcd_omap_mode *port_mode)
+static void setup_4430ehci_io_mux(const enum usbhs_omap_port_mode *port_mode)
{
switch (port_mode[0]) {
- case EHCI_HCD_OMAP_MODE_PHY:
+ case OMAP_EHCI_PORT_MODE_PHY:
omap_mux_init_signal("usbb1_ulpiphy_stp",
OMAP_PIN_OUTPUT);
omap_mux_init_signal("usbb1_ulpiphy_clk",
@@ -236,7 +236,7 @@ static void setup_4430ehci_io_mux(const enum ehci_hcd_omap_mode *port_mode)
omap_mux_init_signal("usbb1_ulpiphy_dat7",
OMAP_PIN_INPUT_PULLDOWN);
break;
- case EHCI_HCD_OMAP_MODE_TLL:
+ case OMAP_EHCI_PORT_MODE_TLL:
omap_mux_init_signal("usbb1_ulpitll_stp",
OMAP_PIN_INPUT_PULLUP);
omap_mux_init_signal("usbb1_ulpitll_clk",
@@ -262,12 +262,12 @@ static void setup_4430ehci_io_mux(const enum ehci_hcd_omap_mode *port_mode)
omap_mux_init_signal("usbb1_ulpitll_dat7",
OMAP_PIN_INPUT_PULLDOWN);
break;
- case EHCI_HCD_OMAP_MODE_UNKNOWN:
+ case OMAP_USBHS_PORT_MODE_UNUSED:
default:
break;
}
switch (port_mode[1]) {
- case EHCI_HCD_OMAP_MODE_PHY:
+ case OMAP_EHCI_PORT_MODE_PHY:
omap_mux_init_signal("usbb2_ulpiphy_stp",
OMAP_PIN_OUTPUT);
omap_mux_init_signal("usbb2_ulpiphy_clk",
@@ -293,7 +293,7 @@ static void setup_4430ehci_io_mux(const enum ehci_hcd_omap_mode *port_mode)
omap_mux_init_signal("usbb2_ulpiphy_dat7",
OMAP_PIN_INPUT_PULLDOWN);
break;
- case EHCI_HCD_OMAP_MODE_TLL:
+ case OMAP_EHCI_PORT_MODE_TLL:
omap_mux_init_signal("usbb2_ulpitll_stp",
OMAP_PIN_INPUT_PULLUP);
omap_mux_init_signal("usbb2_ulpitll_clk",
@@ -319,13 +319,13 @@ static void setup_4430ehci_io_mux(const enum ehci_hcd_omap_mode *port_mode)
omap_mux_init_signal("usbb2_ulpitll_dat7",
OMAP_PIN_INPUT_PULLDOWN);
break;
- case EHCI_HCD_OMAP_MODE_UNKNOWN:
+ case OMAP_USBHS_PORT_MODE_UNUSED:
default:
break;
}
}
-void __init usb_ehci_init(const struct ehci_hcd_omap_platform_data *pdata)
+void __init usb_ehci_init(const struct usbhs_omap_board_data *pdata)
{
platform_device_add_data(&ehci_device, pdata, sizeof(*pdata));
@@ -363,7 +363,7 @@ void __init usb_ehci_init(const struct ehci_hcd_omap_platform_data *pdata)
#else
-void __init usb_ehci_init(const struct ehci_hcd_omap_platform_data *pdata)
+void __init usb_ehci_init(const struct usbhs_omap_board_data *pdata)
{
}
@@ -411,7 +411,7 @@ static struct platform_device ohci_device = {
.resource = ohci_resources,
};
-static void setup_ohci_io_mux(const enum ohci_omap3_port_mode *port_mode)
+static void setup_ohci_io_mux(const enum usbhs_omap_port_mode *port_mode)
{
switch (port_mode[0]) {
case OMAP_OHCI_PORT_MODE_PHY_6PIN_DATSE0:
@@ -439,7 +439,7 @@ static void setup_ohci_io_mux(const enum ohci_omap3_port_mode *port_mode)
omap_mux_init_signal("mm1_txdat",
OMAP_PIN_INPUT_PULLDOWN);
break;
- case OMAP_OHCI_PORT_MODE_UNUSED:
+ case OMAP_USBHS_PORT_MODE_UNUSED:
/* FALLTHROUGH */
default:
break;
@@ -470,7 +470,7 @@ static void setup_ohci_io_mux(const enum ohci_omap3_port_mode *port_mode)
omap_mux_init_signal("mm2_txdat",
OMAP_PIN_INPUT_PULLDOWN);
break;
- case OMAP_OHCI_PORT_MODE_UNUSED:
+ case OMAP_USBHS_PORT_MODE_UNUSED:
/* FALLTHROUGH */
default:
break;
@@ -501,14 +501,14 @@ static void setup_ohci_io_mux(const enum ohci_omap3_port_mode *port_mode)
omap_mux_init_signal("mm3_txdat",
OMAP_PIN_INPUT_PULLDOWN);
break;
- case OMAP_OHCI_PORT_MODE_UNUSED:
+ case OMAP_USBHS_PORT_MODE_UNUSED:
/* FALLTHROUGH */
default:
break;
}
}
-void __init usb_ohci_init(const struct ohci_hcd_omap_platform_data *pdata)
+void __init usb_ohci_init(const struct usbhs_omap_board_data *pdata)
{
platform_device_add_data(&ohci_device, pdata, sizeof(*pdata));
@@ -524,7 +524,7 @@ void __init usb_ohci_init(const struct ohci_hcd_omap_platform_data *pdata)
#else
-void __init usb_ohci_init(const struct ohci_hcd_omap_platform_data *pdata)
+void __init usb_ohci_init(const struct usbhs_omap_board_data *pdata)
{
}
@@ -7,15 +7,12 @@
#include <plat/board.h>
#define OMAP3_HS_USB_PORTS 3
-enum ehci_hcd_omap_mode {
- EHCI_HCD_OMAP_MODE_UNKNOWN,
- EHCI_HCD_OMAP_MODE_PHY,
- EHCI_HCD_OMAP_MODE_TLL,
- EHCI_HCD_OMAP_MODE_HSIC,
-};
-enum ohci_omap3_port_mode {
- OMAP_OHCI_PORT_MODE_UNUSED,
+enum usbhs_omap_port_mode {
+ OMAP_USBHS_PORT_MODE_UNUSED,
+ OMAP_EHCI_PORT_MODE_PHY,
+ OMAP_EHCI_PORT_MODE_TLL,
+ OMAP_EHCI_PORT_MODE_HSIC,
OMAP_OHCI_PORT_MODE_PHY_6PIN_DATSE0,
OMAP_OHCI_PORT_MODE_PHY_6PIN_DPDM,
OMAP_OHCI_PORT_MODE_PHY_3PIN_DATSE0,
@@ -25,24 +22,45 @@ enum ohci_omap3_port_mode {
OMAP_OHCI_PORT_MODE_TLL_3PIN_DATSE0,
OMAP_OHCI_PORT_MODE_TLL_4PIN_DPDM,
OMAP_OHCI_PORT_MODE_TLL_2PIN_DATSE0,
- OMAP_OHCI_PORT_MODE_TLL_2PIN_DPDM,
+ OMAP_OHCI_PORT_MODE_TLL_2PIN_DPDM
};
-struct ehci_hcd_omap_platform_data {
- enum ehci_hcd_omap_mode port_mode[OMAP3_HS_USB_PORTS];
- unsigned phy_reset:1;
+struct usbhs_omap_board_data {
+ enum usbhs_omap_port_mode port_mode[OMAP3_HS_USB_PORTS];
/* have to be valid if phy_reset is true and portx is in phy mode */
int reset_gpio_port[OMAP3_HS_USB_PORTS];
+
+ /* Set this to true for ES2.x silicon */
+ unsigned es2_compatibility:1;
+
+ unsigned phy_reset:1;
+
+ /*
+ * Regulators for USB PHYs.
+ * Each PHY can have a separate regulator.
+ */
+ struct regulator *regulator[OMAP3_HS_USB_PORTS];
};
-struct ohci_hcd_omap_platform_data {
- enum ohci_omap3_port_mode port_mode[OMAP3_HS_USB_PORTS];
+struct ehci_hcd_omap_platform_data {
+ enum usbhs_omap_port_mode port_mode[OMAP3_HS_USB_PORTS];
+ int reset_gpio_port[OMAP3_HS_USB_PORTS];
+ struct regulator *regulator[OMAP3_HS_USB_PORTS];
+ unsigned phy_reset:1;
+};
- /* Set this to true for ES2.x silicon */
+struct ohci_hcd_omap_platform_data {
+ enum usbhs_omap_port_mode port_mode[OMAP3_HS_USB_PORTS];
unsigned es2_compatibility:1;
};
+struct usbhs_omap_platform_data {
+ enum usbhs_omap_port_mode port_mode[OMAP3_HS_USB_PORTS];
+
+ struct ehci_hcd_omap_platform_data *ehci_data;
+ struct ohci_hcd_omap_platform_data *ohci_data;
+};
/*-------------------------------------------------------------------------*/
#define OMAP1_OTG_BASE 0xfffb0400
@@ -80,19 +98,17 @@ enum musb_interface {MUSB_INTERFACE_ULPI, MUSB_INTERFACE_UTMI};
extern void usb_musb_init(struct omap_musb_board_data *board_data);
-extern void usb_ehci_init(const struct ehci_hcd_omap_platform_data *pdata);
+extern void usb_ehci_init(const struct usbhs_omap_board_data *pdata);
-extern void usb_ohci_init(const struct ohci_hcd_omap_platform_data *pdata);
+extern void usb_ohci_init(const struct usbhs_omap_board_data *pdata);
extern int omap4430_phy_power(struct device *dev, int ID, int on);
extern int omap4430_phy_set_clk(struct device *dev, int on);
extern int omap4430_phy_init(struct device *dev);
extern int omap4430_phy_exit(struct device *dev);
extern int omap4430_phy_suspend(struct device *dev, int suspend);
-
#endif
-
/*
* FIXME correct answer depends on hmc_mode,
* as does (on omap1) any nonzero value for config->otg port number
@@ -155,9 +155,9 @@
#define is_omap_ehci_rev1(x) (x->omap_ehci_rev == OMAP_EHCI_REV1)
#define is_omap_ehci_rev2(x) (x->omap_ehci_rev == OMAP_EHCI_REV2)
-#define is_ehci_phy_mode(x) (x == EHCI_HCD_OMAP_MODE_PHY)
-#define is_ehci_tll_mode(x) (x == EHCI_HCD_OMAP_MODE_TLL)
-#define is_ehci_hsic_mode(x) (x == EHCI_HCD_OMAP_MODE_HSIC)
+#define is_ehci_phy_mode(x) (x == OMAP_EHCI_PORT_MODE_PHY)
+#define is_ehci_tll_mode(x) (x == OMAP_EHCI_PORT_MODE_TLL)
+#define is_ehci_hsic_mode(x) (x == OMAP_EHCI_PORT_MODE_HSIC)
/*-------------------------------------------------------------------------*/
@@ -220,7 +220,7 @@ struct ehci_hcd_omap {
u32 omap_ehci_rev;
/* desired phy_mode: TLL, PHY */
- enum ehci_hcd_omap_mode port_mode[OMAP3_HS_USB_PORTS];
+ enum usbhs_omap_port_mode port_mode[OMAP3_HS_USB_PORTS];
void __iomem *uhh_base;
void __iomem *tll_base;
@@ -389,7 +389,7 @@ static int omap_start_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd)
*/
if (is_omap_ehci_rev2(omap)) {
switch (omap->port_mode[0]) {
- case EHCI_HCD_OMAP_MODE_PHY:
+ case OMAP_EHCI_PORT_MODE_PHY:
omap->xclk60mhsp1_ck = clk_get(omap->dev,
"xclk60mhsp1_ck");
if (IS_ERR(omap->xclk60mhsp1_ck)) {
@@ -413,7 +413,7 @@ static int omap_start_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd)
"Unable to set P1 f-clock\n");
}
break;
- case EHCI_HCD_OMAP_MODE_TLL:
+ case OMAP_EHCI_PORT_MODE_TLL:
omap->xclk60mhsp1_ck = clk_get(omap->dev,
"init_60m_fclk");
if (IS_ERR(omap->xclk60mhsp1_ck)) {
@@ -463,7 +463,7 @@ static int omap_start_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd)
break;
}
switch (omap->port_mode[1]) {
- case EHCI_HCD_OMAP_MODE_PHY:
+ case OMAP_EHCI_PORT_MODE_PHY:
omap->xclk60mhsp2_ck = clk_get(omap->dev,
"xclk60mhsp2_ck");
if (IS_ERR(omap->xclk60mhsp2_ck)) {
@@ -487,7 +487,7 @@ static int omap_start_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd)
"Unable to set P2 f-clock\n");
}
break;
- case EHCI_HCD_OMAP_MODE_TLL:
+ case OMAP_EHCI_PORT_MODE_TLL:
omap->xclk60mhsp2_ck = clk_get(omap->dev,
"init_60m_fclk");
if (IS_ERR(omap->xclk60mhsp2_ck)) {
@@ -591,11 +591,11 @@ static int omap_start_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd)
reg &= ~OMAP_UHH_HOSTCONFIG_INCRX_ALIGN_EN;
if (is_omap_ehci_rev1(omap)) {
- if (omap->port_mode[0] == EHCI_HCD_OMAP_MODE_UNKNOWN)
+ if (omap->port_mode[0] == OMAP_USBHS_PORT_MODE_UNUSED)
reg &= ~OMAP_UHH_HOSTCONFIG_P1_CONNECT_STATUS;
- if (omap->port_mode[1] == EHCI_HCD_OMAP_MODE_UNKNOWN)
+ if (omap->port_mode[1] == OMAP_USBHS_PORT_MODE_UNUSED)
reg &= ~OMAP_UHH_HOSTCONFIG_P2_CONNECT_STATUS;
- if (omap->port_mode[2] == EHCI_HCD_OMAP_MODE_UNKNOWN)
+ if (omap->port_mode[2] == OMAP_USBHS_PORT_MODE_UNUSED)
reg &= ~OMAP_UHH_HOSTCONFIG_P3_CONNECT_STATUS;
/* Bypass the TLL module for PHY mode operation */
@@ -656,15 +656,15 @@ static int omap_start_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd)
ehci_omap_writel(omap->ehci_base, EHCI_INSNREG04,
EHCI_INSNREG04_DISABLE_UNSUSPEND);
- if ((omap->port_mode[0] == EHCI_HCD_OMAP_MODE_TLL) ||
- (omap->port_mode[1] == EHCI_HCD_OMAP_MODE_TLL) ||
- (omap->port_mode[2] == EHCI_HCD_OMAP_MODE_TLL)) {
+ if ((omap->port_mode[0] == OMAP_EHCI_PORT_MODE_TLL) ||
+ (omap->port_mode[1] == OMAP_EHCI_PORT_MODE_TLL) ||
+ (omap->port_mode[2] == OMAP_EHCI_PORT_MODE_TLL)) {
- if (omap->port_mode[0] == EHCI_HCD_OMAP_MODE_TLL)
+ if (omap->port_mode[0] == OMAP_EHCI_PORT_MODE_TLL)
tll_ch_mask |= OMAP_TLL_CHANNEL_1_EN_MASK;
- if (omap->port_mode[1] == EHCI_HCD_OMAP_MODE_TLL)
+ if (omap->port_mode[1] == OMAP_EHCI_PORT_MODE_TLL)
tll_ch_mask |= OMAP_TLL_CHANNEL_2_EN_MASK;
- if (omap->port_mode[2] == EHCI_HCD_OMAP_MODE_TLL)
+ if (omap->port_mode[2] == OMAP_EHCI_PORT_MODE_TLL)
tll_ch_mask |= OMAP_TLL_CHANNEL_3_EN_MASK;
/* Enable UTMI mode for required TLL channels */
@@ -686,9 +686,9 @@ static int omap_start_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd)
}
/* Soft reset the PHY using PHY reset command over ULPI */
- if (omap->port_mode[0] == EHCI_HCD_OMAP_MODE_PHY)
+ if (omap->port_mode[0] == OMAP_EHCI_PORT_MODE_PHY)
omap_ehci_soft_phy_reset(omap, 0);
- if (omap->port_mode[1] == EHCI_HCD_OMAP_MODE_PHY)
+ if (omap->port_mode[1] == OMAP_EHCI_PORT_MODE_PHY)
omap_ehci_soft_phy_reset(omap, 1);
return 0;
@@ -903,7 +903,7 @@ static const struct hc_driver ehci_omap_hc_driver;
*/
static int ehci_hcd_omap_probe(struct platform_device *pdev)
{
- struct ehci_hcd_omap_platform_data *pdata = pdev->dev.platform_data;
+ struct usbhs_omap_board_data *pdata = pdev->dev.platform_data;
struct ehci_hcd_omap *omap;
struct resource *res;
struct usb_hcd *hcd;
@@ -981,7 +981,7 @@ static int ehci_hcd_omap_probe(struct platform_device *pdev)
/* get ehci regulator and enable */
for (i = 0 ; i < OMAP3_HS_USB_PORTS ; i++) {
- if (omap->port_mode[i] != EHCI_HCD_OMAP_MODE_PHY) {
+ if (omap->port_mode[i] != OMAP_EHCI_PORT_MODE_PHY) {
omap->regulator[i] = NULL;
continue;
}
@@ -141,7 +141,7 @@ struct ohci_hcd_omap3 {
struct clk *usbtll_ick;
/* port_mode: TLL/PHY, 2/3/4/6-PIN, DP-DM/DAT-SE0 */
- enum ohci_omap3_port_mode port_mode[OMAP3_HS_USB_PORTS];
+ enum usbhs_omap_port_mode port_mode[OMAP3_HS_USB_PORTS];
void __iomem *uhh_base;
void __iomem *tll_base;
void __iomem *ohci_base;
@@ -206,10 +206,10 @@ static int ohci_omap3_start(struct usb_hcd *hcd)
* convert the port-mode enum to a value we can use in the FSLSMODE
* field of USBTLL_CHANNEL_CONF
*/
-static unsigned ohci_omap3_fslsmode(enum ohci_omap3_port_mode mode)
+static unsigned ohci_omap3_fslsmode(enum usbhs_omap_port_mode mode)
{
switch (mode) {
- case OMAP_OHCI_PORT_MODE_UNUSED:
+ case OMAP_USBHS_PORT_MODE_UNUSED:
case OMAP_OHCI_PORT_MODE_PHY_6PIN_DATSE0:
return 0x0;
@@ -266,7 +266,7 @@ static void ohci_omap3_tll_config(struct ohci_hcd_omap3 *omap)
for (i = 0; i < OMAP_TLL_CHANNEL_COUNT; i++) {
/* Enable only those channels that are actually used */
- if (omap->port_mode[i] == OMAP_OHCI_PORT_MODE_UNUSED)
+ if (omap->port_mode[i] == OMAP_USBHS_PORT_MODE_UNUSED)
continue;
reg = ohci_omap_readl(omap->tll_base, OMAP_TLL_CHANNEL_CONF(i));
@@ -382,11 +382,11 @@ static int omap3_start_ohci(struct ohci_hcd_omap3 *omap, struct usb_hcd *hcd)
*
* For now, turn off all the Pi_CONNECT_STATUS bits
*
- if (omap->port_mode[0] == OMAP_OHCI_PORT_MODE_UNUSED)
+ if (omap->port_mode[0] == OMAP_USBHS_PORT_MODE_UNUSED)
reg &= ~OMAP_UHH_HOSTCONFIG_P1_CONNECT_STATUS;
- if (omap->port_mode[1] == OMAP_OHCI_PORT_MODE_UNUSED)
+ if (omap->port_mode[1] == OMAP_USBHS_PORT_MODE_UNUSED)
reg &= ~OMAP_UHH_HOSTCONFIG_P2_CONNECT_STATUS;
- if (omap->port_mode[2] == OMAP_OHCI_PORT_MODE_UNUSED)
+ if (omap->port_mode[2] == OMAP_USBHS_PORT_MODE_UNUSED)
reg &= ~OMAP_UHH_HOSTCONFIG_P3_CONNECT_STATUS;
*/
reg &= ~OMAP_UHH_HOSTCONFIG_P1_CONNECT_STATUS;
@@ -403,17 +403,17 @@ static int omap3_start_ohci(struct ohci_hcd_omap3 *omap, struct usb_hcd *hcd)
reg |= OMAP_UHH_HOSTCONFIG_ULPI_BYPASS;
} else {
dev_dbg(omap->dev, "OMAP3 ES version > ES2.1\n");
- if (omap->port_mode[0] == OMAP_OHCI_PORT_MODE_UNUSED)
+ if (omap->port_mode[0] == OMAP_USBHS_PORT_MODE_UNUSED)
reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS;
else
reg |= OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS;
- if (omap->port_mode[1] == OMAP_OHCI_PORT_MODE_UNUSED)
+ if (omap->port_mode[1] == OMAP_USBHS_PORT_MODE_UNUSED)
reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P2_BYPASS;
else
reg |= OMAP_UHH_HOSTCONFIG_ULPI_P2_BYPASS;
- if (omap->port_mode[2] == OMAP_OHCI_PORT_MODE_UNUSED)
+ if (omap->port_mode[2] == OMAP_USBHS_PORT_MODE_UNUSED)
reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS;
else
reg |= OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS;
@@ -580,7 +580,7 @@ static const struct hc_driver ohci_omap3_hc_driver = {
*/
static int __devinit ohci_hcd_omap3_probe(struct platform_device *pdev)
{
- struct ohci_hcd_omap_platform_data *pdata = pdev->dev.platform_data;
+ struct usbhs_omap_board_data *pdata = pdev->dev.platform_data;
struct ohci_hcd_omap3 *omap;
struct resource *res;
struct usb_hcd *hcd;