@@ -80,6 +80,7 @@ endif
obj-$(CONFIG_ARCH_OMAP2) += prcm.o cm2xxx_3xxx.o prm2xxx_3xxx.o
obj-$(CONFIG_ARCH_OMAP3) += prcm.o cm2xxx_3xxx.o prm2xxx_3xxx.o \
vc3xxx_data.o vp3xxx_data.o
+obj-$(CONFIG_SOC_OMAPTI816X) += cm816x.o
# XXX The presence of cm2xxx_3xxx.o on the line below is temporary and
# will be removed once the OMAP4 part of the codebase is converted to
# use OMAP4-specific PRCM functions.
@@ -149,6 +150,7 @@ obj-$(CONFIG_SOC_OMAP2430) += opp2430_data.o
obj-$(CONFIG_SOC_OMAP2420) += omap_hwmod_2420_data.o
obj-$(CONFIG_SOC_OMAP2430) += omap_hwmod_2430_data.o
obj-$(CONFIG_ARCH_OMAP3) += omap_hwmod_3xxx_data.o
+obj-$(CONFIG_SOC_OMAPTI816X) += omap_hwmod_816x_data.o
obj-$(CONFIG_ARCH_OMAP4) += omap_hwmod_44xx_data.o
# EMU peripherals
@@ -122,6 +122,7 @@ extern void omap3xxx_cm_clkdm_disable_hwsup(s16 module, u32 mask);
extern void omap3xxx_cm_clkdm_force_sleep(s16 module, u32 mask);
extern void omap3xxx_cm_clkdm_force_wakeup(s16 module, u32 mask);
+extern int ti816x_cm_wait_module_ready(void __iomem *clkctrl_reg);
extern void ti816x_cm_clkdm_enable_hwsup(s16 inst, u16 clkdm, u32 mask);
extern void ti816x_cm_clkdm_disable_hwsup(s16 inst, u16 clkdm, u32 mask);
extern void ti816x_cm_clkdm_force_sleep(s16 inst, u16 clkdm, u32 mask);
new file mode 100644
@@ -0,0 +1,55 @@
+/*
+ * TI816X CM module functions
+ *
+ * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * Based on arch/arm/mach-omap2/cm4xxx.c, original copyright follows:
+ *
+ * Copyright (C) 2009 Nokia Corporation
+ * Paul Walmsley
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/delay.h>
+#include <linux/errno.h>
+#include <linux/err.h>
+#include <linux/io.h>
+
+#include <plat/common.h>
+
+#include "cm.h"
+#include "cm-regbits-816x.h"
+
+/**
+ * ti816x_cm_wait_module_ready - wait for a module to be in 'func' state
+ * @clkctrl_reg: CLKCTRL module address
+ *
+ * Wait for the module IDLEST to be functional. If the idle state is in any
+ * the non functional state (trans, idle or disabled), module and thus the
+ * sysconfig cannot be accessed and will probably lead to an "imprecise
+ * external abort"
+ *
+ * Module idle state:
+ * 0x0 func: Module is fully functional, including OCP
+ * 0x1 trans: Module is performing transition: wakeup, or sleep, or sleep
+ * abortion
+ * 0x2 idle: Module is in Idle mode (only OCP part). It is functional if
+ * using separate functional clock
+ * 0x3 disabled: Module is disabled and cannot be accessed
+ *
+ */
+int ti816x_cm_wait_module_ready(void __iomem *clkctrl_reg)
+{
+ int i = 0;
+
+ if (!clkctrl_reg)
+ return 0;
+
+ omap_test_timeout((
+ ((__raw_readl(clkctrl_reg) & TI816X_IDLEST_MASK) == 0)),
+ MAX_MODULE_READY_TIME, i);
+
+ return (i < MAX_MODULE_READY_TIME) ? 0 : -EBUSY;
+}
@@ -366,6 +366,7 @@ void __init omap2_init_common_infrastructure(void)
omap3xxx_powerdomains_init();
omap3xxx_clockdomains_init();
omap3xxx_hwmod_init();
+ ti816x_hwmod_init();
} else if (cpu_is_omap44xx()) {
omap44xx_powerdomains_init();
omap44xx_clockdomains_init();
@@ -962,9 +962,14 @@ static int _wait_target_ready(struct omap_hwmod *oh)
/* XXX check clock enable states */
if (cpu_is_omap24xx() || cpu_is_omap34xx()) {
- ret = omap2_cm_wait_module_ready(oh->prcm.omap2.module_offs,
- oh->prcm.omap2.idlest_reg_id,
- oh->prcm.omap2.idlest_idle_bit);
+ if (cpu_is_ti816x())
+ ret = ti816x_cm_wait_module_ready(
+ oh->prcm.omap4.clkctrl_reg);
+ else
+ ret = omap2_cm_wait_module_ready(
+ oh->prcm.omap2.module_offs,
+ oh->prcm.omap2.idlest_reg_id,
+ oh->prcm.omap2.idlest_idle_bit);
} else if (cpu_is_omap44xx()) {
ret = omap4_cm_wait_module_ready(oh->prcm.omap4.clkctrl_reg);
} else {
@@ -610,5 +610,6 @@ extern int omap2420_hwmod_init(void);
extern int omap2430_hwmod_init(void);
extern int omap3xxx_hwmod_init(void);
extern int omap44xx_hwmod_init(void);
+extern int ti816x_hwmod_init(void);
#endif
This patch integrates TI816X hwmods into hwmods framework. Note that a TI816X specific function ti816x_cm_wait_module_ready() is added to wait for module to become ready since corresponding OMAP2/3 function omap2_cm_wait_module_ready() cannot be used as there are no IDLEST registers in TI816X. Signed-off-by: Hemant Pedanekar <hemantp@ti.com> --- This patch depends on following patch set: TI816X: prcm: Add module and register offsets TI816X: clock: Add clock data TI816X: clock: Add clockdomains and powerdomains data clock: Integrate TI816X clock data into OMAP clock framework arch/arm/mach-omap2/Makefile | 2 + arch/arm/mach-omap2/cm2xxx_3xxx.h | 1 + arch/arm/mach-omap2/cm816x.c | 55 ++++++++++++++++++++++++++ arch/arm/mach-omap2/io.c | 1 + arch/arm/mach-omap2/omap_hwmod.c | 11 ++++- arch/arm/plat-omap/include/plat/omap_hwmod.h | 1 + 6 files changed, 68 insertions(+), 3 deletions(-) create mode 100644 arch/arm/mach-omap2/cm816x.c