| Message ID | 1342607922-11554-10-git-send-email-kishon@ti.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Hi, > Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> > --- > Documentation/devicetree/bindings/usb/omap-usb.txt | 34 ++++++++++++- > drivers/usb/musb/omap2430.c | 55 > ++++++++++++++++++++ > 2 files changed, 88 insertions(+), 1 deletions(-) > > diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt > b/Documentation/devicetree/bindings/usb/omap-usb.txt > index 80a28c9..39cdffb 100644 > --- a/Documentation/devicetree/bindings/usb/omap-usb.txt > +++ b/Documentation/devicetree/bindings/usb/omap-usb.txt > @@ -1,4 +1,4 @@ > -OMAP USB PHY > +OMAP USB PHY AND GLUE > > OMAP USB2 PHY > > @@ -14,3 +14,35 @@ usb2phy@0x4a0ad080 { > compatible = "ti,omap-usb2"; > reg = <0x4a0ad080 0x58>; > }; > + > +OMAP MUSB GLUE > + - compatible : Should be "ti,musb-omap2430" > + - ti,hwmods : must be "usb_otg_hs" > + - multipoint : Should be "1" indicating the musb controller supports > + multipoint. This is a MUSB configuration-specific setting. > + - num_eps : Specifies the number of endpoints. This is also a > + MUSB configuration-specific setting. Should be set to "16" > + - ram_bits : Specifies the ram address size. Should be set to "12" > + - interface_type : This is a board specific setting to describe the type > of > + interface between the controller and the phy. It should be "0" or "1" > + specifying ULPI and UTMI respectively. > + - mode : Should be "3" to represent OTG. "1" signifies HOST and "2" > + represents PERIPHERAL. > + - power : Should be "50". This signifies the controller can supply upto > + 100mA when operating in host mode. > + > +SOC specific device node entry > +usb_otg_hs: usb_otg_hs@4a0ab000 { > + compatible = "ti,musb-omap2430"; > + ti,hwmods = "usb_otg_hs"; > + multipoint = <1>; > + num_eps = <16>; > + ram_bits = <12>; > +}; > + > +Board specific device node entry > +&usb_otg_hs { > + interface_type = <1>; > + mode = <3>; > + power = <50>; > +}; > diff --git a/drivers/usb/musb/omap2430.c b/drivers/usb/musb/omap2430.c > index addbebf..331e477 100644 > --- a/drivers/usb/musb/omap2430.c > +++ b/drivers/usb/musb/omap2430.c > @@ -30,6 +30,7 @@ > #include <linux/init.h> > #include <linux/list.h> > #include <linux/io.h> > +#include <linux/of.h> > #include <linux/platform_device.h> > #include <linux/dma-mapping.h> > #include <linux/pm_runtime.h> > @@ -469,8 +470,11 @@ static u64 omap2430_dmamask = DMA_BIT_MASK(32); > static int __devinit omap2430_probe(struct platform_device *pdev) > { > struct musb_hdrc_platform_data *pdata = pdev->dev.platform_data; > + struct omap_musb_board_data *data; > struct platform_device *musb; > struct omap2430_glue *glue; > + struct device_node *np = pdev->dev.of_node; > + struct musb_hdrc_config *config; > struct resource *res; > int ret = -ENOMEM; > > @@ -500,6 +504,43 @@ static int __devinit omap2430_probe(struct > platform_device *pdev) > if (glue->control_otghs == NULL) > dev_dbg(&pdev->dev, "Failed to obtain control memory\n"); > > + if (np) { > + pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL); > + if (!pdata) { > + dev_err(&pdev->dev, > + "failed to allocate musb platfrom data\n"); > + ret = -ENOMEM; > + goto err1; > + } > + > + data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL); > + if (!data) { > + dev_err(&pdev->dev, > + "failed to allocate musb board data\n"); > + ret = -ENOMEM; > + goto err1; > + } > + > + config = devm_kzalloc(&pdev->dev, sizeof(*config), GFP_KERNEL); > + if (!data) { > + dev_err(&pdev->dev, > + "failed to allocate musb hdrc config\n"); > + goto err1; > + } > + > + of_property_read_u32(np, "mode", (u32 *)&pdata->mode); > + of_property_read_u32(np, "interface_type", > + (u32 *)&data->interface_type); > + of_property_read_u32(np, "num_eps", (u32 *)&config->num_eps); > + of_property_read_u32(np, "ram_bits", (u32 *)&config->ram_bits); > + of_property_read_u32(np, "mode", (u32 *)&pdata->mode); pdata->mode is already read so above should be removed. Ajay > + of_property_read_u32(np, "power", (u32 *)&pdata->power); > + config->multipoint = of_property_read_bool(np, "multipoint"); > + > + pdata->board_data = data; > + pdata->config = config; > + } > + > pdata->platform_ops = &omap2430_ops; > > platform_set_drvdata(pdev, glue); > @@ -597,12 +638,26 @@ static struct dev_pm_ops omap2430_pm_ops = { > #define DEV_PM_OPS NULL > #endif > > +#ifdef CONFIG_OF > +static const struct of_device_id omap2430_id_table[] = { > + { > + .compatible = "ti,omap4-musb" > + }, > + { > + .compatible = "ti,omap3-musb" > + }, > + {}, > +}; > +MODULE_DEVICE_TABLE(of, omap2430_id_table); > +#endif > + > static struct platform_driver omap2430_driver = { > .probe = omap2430_probe, > .remove = __devexit_p(omap2430_remove), > .driver = { > .name = "musb-omap2430", > .pm = DEV_PM_OPS, > + .of_match_table = of_match_ptr(omap2430_id_table), > }, > }; > > -- > 1.7.5.4 > > -- > To unsubscribe from this list: send the line "unsubscribe linux-omap" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi, On Thu, Jul 19, 2012 at 6:51 PM, Gupta, Ajay Kumar <ajay.gupta@ti.com> wrote: > Hi, >> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> >> --- >> Documentation/devicetree/bindings/usb/omap-usb.txt | 34 ++++++++++++- >> drivers/usb/musb/omap2430.c | 55 >> ++++++++++++++++++++ >> 2 files changed, 88 insertions(+), 1 deletions(-) >> >> diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt >> b/Documentation/devicetree/bindings/usb/omap-usb.txt >> index 80a28c9..39cdffb 100644 >> --- a/Documentation/devicetree/bindings/usb/omap-usb.txt >> +++ b/Documentation/devicetree/bindings/usb/omap-usb.txt >> @@ -1,4 +1,4 @@ >> -OMAP USB PHY >> +OMAP USB PHY AND GLUE >> >> OMAP USB2 PHY >> >> @@ -14,3 +14,35 @@ usb2phy@0x4a0ad080 { >> compatible = "ti,omap-usb2"; >> reg = <0x4a0ad080 0x58>; >> }; >> + >> +OMAP MUSB GLUE >> + - compatible : Should be "ti,musb-omap2430" >> + - ti,hwmods : must be "usb_otg_hs" >> + - multipoint : Should be "1" indicating the musb controller supports >> + multipoint. This is a MUSB configuration-specific setting. >> + - num_eps : Specifies the number of endpoints. This is also a >> + MUSB configuration-specific setting. Should be set to "16" >> + - ram_bits : Specifies the ram address size. Should be set to "12" >> + - interface_type : This is a board specific setting to describe the type >> of >> + interface between the controller and the phy. It should be "0" or "1" >> + specifying ULPI and UTMI respectively. >> + - mode : Should be "3" to represent OTG. "1" signifies HOST and "2" >> + represents PERIPHERAL. >> + - power : Should be "50". This signifies the controller can supply upto >> + 100mA when operating in host mode. >> + >> +SOC specific device node entry >> +usb_otg_hs: usb_otg_hs@4a0ab000 { >> + compatible = "ti,musb-omap2430"; >> + ti,hwmods = "usb_otg_hs"; >> + multipoint = <1>; >> + num_eps = <16>; >> + ram_bits = <12>; >> +}; >> + >> +Board specific device node entry >> +&usb_otg_hs { >> + interface_type = <1>; >> + mode = <3>; >> + power = <50>; >> +}; >> diff --git a/drivers/usb/musb/omap2430.c b/drivers/usb/musb/omap2430.c >> index addbebf..331e477 100644 >> --- a/drivers/usb/musb/omap2430.c >> +++ b/drivers/usb/musb/omap2430.c >> @@ -30,6 +30,7 @@ >> #include <linux/init.h> >> #include <linux/list.h> >> #include <linux/io.h> >> +#include <linux/of.h> >> #include <linux/platform_device.h> >> #include <linux/dma-mapping.h> >> #include <linux/pm_runtime.h> >> @@ -469,8 +470,11 @@ static u64 omap2430_dmamask = DMA_BIT_MASK(32); >> static int __devinit omap2430_probe(struct platform_device *pdev) >> { >> struct musb_hdrc_platform_data *pdata = pdev->dev.platform_data; >> + struct omap_musb_board_data *data; >> struct platform_device *musb; >> struct omap2430_glue *glue; >> + struct device_node *np = pdev->dev.of_node; >> + struct musb_hdrc_config *config; >> struct resource *res; >> int ret = -ENOMEM; >> >> @@ -500,6 +504,43 @@ static int __devinit omap2430_probe(struct >> platform_device *pdev) >> if (glue->control_otghs == NULL) >> dev_dbg(&pdev->dev, "Failed to obtain control memory\n"); >> >> + if (np) { >> + pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL); >> + if (!pdata) { >> + dev_err(&pdev->dev, >> + "failed to allocate musb platfrom data\n"); >> + ret = -ENOMEM; >> + goto err1; >> + } >> + >> + data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL); >> + if (!data) { >> + dev_err(&pdev->dev, >> + "failed to allocate musb board data\n"); >> + ret = -ENOMEM; >> + goto err1; >> + } >> + >> + config = devm_kzalloc(&pdev->dev, sizeof(*config), GFP_KERNEL); >> + if (!data) { >> + dev_err(&pdev->dev, >> + "failed to allocate musb hdrc config\n"); >> + goto err1; >> + } >> + >> + of_property_read_u32(np, "mode", (u32 *)&pdata->mode); >> + of_property_read_u32(np, "interface_type", >> + (u32 *)&data->interface_type); >> + of_property_read_u32(np, "num_eps", (u32 *)&config->num_eps); >> + of_property_read_u32(np, "ram_bits", (u32 *)&config->ram_bits); >> + of_property_read_u32(np, "mode", (u32 *)&pdata->mode); > > pdata->mode is already read so above should be removed. Ok. Thanks Kishon -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt index 80a28c9..39cdffb 100644 --- a/Documentation/devicetree/bindings/usb/omap-usb.txt +++ b/Documentation/devicetree/bindings/usb/omap-usb.txt @@ -1,4 +1,4 @@ -OMAP USB PHY +OMAP USB PHY AND GLUE OMAP USB2 PHY @@ -14,3 +14,35 @@ usb2phy@0x4a0ad080 { compatible = "ti,omap-usb2"; reg = <0x4a0ad080 0x58>; }; + +OMAP MUSB GLUE + - compatible : Should be "ti,musb-omap2430" + - ti,hwmods : must be "usb_otg_hs" + - multipoint : Should be "1" indicating the musb controller supports + multipoint. This is a MUSB configuration-specific setting. + - num_eps : Specifies the number of endpoints. This is also a + MUSB configuration-specific setting. Should be set to "16" + - ram_bits : Specifies the ram address size. Should be set to "12" + - interface_type : This is a board specific setting to describe the type of + interface between the controller and the phy. It should be "0" or "1" + specifying ULPI and UTMI respectively. + - mode : Should be "3" to represent OTG. "1" signifies HOST and "2" + represents PERIPHERAL. + - power : Should be "50". This signifies the controller can supply upto + 100mA when operating in host mode. + +SOC specific device node entry +usb_otg_hs: usb_otg_hs@4a0ab000 { + compatible = "ti,musb-omap2430"; + ti,hwmods = "usb_otg_hs"; + multipoint = <1>; + num_eps = <16>; + ram_bits = <12>; +}; + +Board specific device node entry +&usb_otg_hs { + interface_type = <1>; + mode = <3>; + power = <50>; +}; diff --git a/drivers/usb/musb/omap2430.c b/drivers/usb/musb/omap2430.c index addbebf..331e477 100644 --- a/drivers/usb/musb/omap2430.c +++ b/drivers/usb/musb/omap2430.c @@ -30,6 +30,7 @@ #include <linux/init.h> #include <linux/list.h> #include <linux/io.h> +#include <linux/of.h> #include <linux/platform_device.h> #include <linux/dma-mapping.h> #include <linux/pm_runtime.h> @@ -469,8 +470,11 @@ static u64 omap2430_dmamask = DMA_BIT_MASK(32); static int __devinit omap2430_probe(struct platform_device *pdev) { struct musb_hdrc_platform_data *pdata = pdev->dev.platform_data; + struct omap_musb_board_data *data; struct platform_device *musb; struct omap2430_glue *glue; + struct device_node *np = pdev->dev.of_node; + struct musb_hdrc_config *config; struct resource *res; int ret = -ENOMEM; @@ -500,6 +504,43 @@ static int __devinit omap2430_probe(struct platform_device *pdev) if (glue->control_otghs == NULL) dev_dbg(&pdev->dev, "Failed to obtain control memory\n"); + if (np) { + pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL); + if (!pdata) { + dev_err(&pdev->dev, + "failed to allocate musb platfrom data\n"); + ret = -ENOMEM; + goto err1; + } + + data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL); + if (!data) { + dev_err(&pdev->dev, + "failed to allocate musb board data\n"); + ret = -ENOMEM; + goto err1; + } + + config = devm_kzalloc(&pdev->dev, sizeof(*config), GFP_KERNEL); + if (!data) { + dev_err(&pdev->dev, + "failed to allocate musb hdrc config\n"); + goto err1; + } + + of_property_read_u32(np, "mode", (u32 *)&pdata->mode); + of_property_read_u32(np, "interface_type", + (u32 *)&data->interface_type); + of_property_read_u32(np, "num_eps", (u32 *)&config->num_eps); + of_property_read_u32(np, "ram_bits", (u32 *)&config->ram_bits); + of_property_read_u32(np, "mode", (u32 *)&pdata->mode); + of_property_read_u32(np, "power", (u32 *)&pdata->power); + config->multipoint = of_property_read_bool(np, "multipoint"); + + pdata->board_data = data; + pdata->config = config; + } + pdata->platform_ops = &omap2430_ops; platform_set_drvdata(pdev, glue); @@ -597,12 +638,26 @@ static struct dev_pm_ops omap2430_pm_ops = { #define DEV_PM_OPS NULL #endif +#ifdef CONFIG_OF +static const struct of_device_id omap2430_id_table[] = { + { + .compatible = "ti,omap4-musb" + }, + { + .compatible = "ti,omap3-musb" + }, + {}, +}; +MODULE_DEVICE_TABLE(of, omap2430_id_table); +#endif + static struct platform_driver omap2430_driver = { .probe = omap2430_probe, .remove = __devexit_p(omap2430_remove), .driver = { .name = "musb-omap2430", .pm = DEV_PM_OPS, + .of_match_table = of_match_ptr(omap2430_id_table), }, };
Added device tree support for omap musb driver and updated the Documentation with device tree binding information. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> --- Documentation/devicetree/bindings/usb/omap-usb.txt | 34 ++++++++++++- drivers/usb/musb/omap2430.c | 55 ++++++++++++++++++++ 2 files changed, 88 insertions(+), 1 deletions(-)