@@ -300,6 +300,8 @@ static struct {
struct regulator *vdda_dac_reg;
struct clk *tv_dac_clk;
+
+ struct omap_video_timings timings;
} venc;
static inline void venc_write_reg(int idx, u32 val)
@@ -432,7 +434,7 @@ static int venc_power_on(struct omap_dss_device *dssdev)
goto err0;
venc_reset();
- venc_write_config(venc_timings_to_config(&dssdev->panel.timings));
+ venc_write_config(venc_timings_to_config(&venc.timings));
dss_set_venc_output(dssdev->phy.venc.type);
dss_set_dac_pwrdn_bgz(1);
@@ -449,7 +451,7 @@ static int venc_power_on(struct omap_dss_device *dssdev)
venc_write_reg(VENC_OUTPUT_CONTROL, l);
- dss_mgr_set_timings(dssdev->manager, &dssdev->panel.timings);
+ dss_mgr_set_timings(dssdev->manager, &venc.timings);
r = regulator_enable(venc.vdda_dac_reg);
if (r)
@@ -556,10 +558,10 @@ void omapdss_venc_set_timings(struct omap_dss_device *dssdev,
mutex_lock(&venc.venc_lock);
/* Reset WSS data when the TV standard changes. */
- if (memcmp(&dssdev->panel.timings, timings, sizeof(*timings)))
+ if (memcmp(&venc.timings, timings, sizeof(*timings)))
venc.wss_data = 0;
- dssdev->panel.timings = *timings;
+ venc.timings = *timings;
if (dssdev->state == OMAP_DSS_DISPLAY_ACTIVE) {
int r;
@@ -606,7 +608,7 @@ int omapdss_venc_set_wss(struct omap_dss_device *dssdev, u32 wss)
mutex_lock(&venc.venc_lock);
- config = venc_timings_to_config(&dssdev->panel.timings);
+ config = venc_timings_to_config(&venc.timings);
/* Invert due to VENC_L21_WC_CTL:INV=1 */
venc.wss_data = (wss ^ 0xfffff) << 8;
@@ -170,6 +170,7 @@ static void venc_panel_set_timings(struct omap_dss_device *dssdev,
mutex_lock(&venc_panel.lock);
omapdss_venc_set_timings(dssdev, timings);
+ dssdev->panel.timings = *timings;
mutex_unlock(&venc_panel.lock);
}
The VENC driver currently relies on the timings in omap_dss_device struct to configure the DISPC and VENC blocks accordingly. This makes the VENC interface driver dependent on the omap_dss_device struct. Make the VENC driver data maintain it's own timings field. The panel driver is expected to call omapdss_venc_set_timings() to set these timings before the panel is enabled. Make the VENC panel driver configure the new timings is the omap_dss_device struct(dssdev->panel.timings). The VENC driver is responsible for maintaining only it's own copy of timings. Signed-off-by: Archit Taneja <archit@ti.com> --- drivers/video/omap2/dss/venc.c | 12 +++++++----- drivers/video/omap2/dss/venc_panel.c | 1 + 2 files changed, 8 insertions(+), 5 deletions(-)