@@ -106,34 +106,22 @@ static struct twl4030_keypad_data sdp3430_kp_data = {
#define SDP3430_LCD_PANEL_BACKLIGHT_GPIO 8
#define SDP3430_LCD_PANEL_ENABLE_GPIO 5
-static struct gpio sdp3430_dss_gpios[] __initdata = {
- {SDP3430_LCD_PANEL_ENABLE_GPIO, GPIOF_OUT_INIT_LOW, "LCD reset" },
- {SDP3430_LCD_PANEL_BACKLIGHT_GPIO, GPIOF_OUT_INIT_LOW, "LCD Backlight"},
-};
-
static void __init sdp3430_display_init(void)
{
int r;
- r = gpio_request_array(sdp3430_dss_gpios,
- ARRAY_SIZE(sdp3430_dss_gpios));
+ /*
+ * the backlight GPIO doesn't directly go to the panel, it enables
+ * an internal circuit on 3430sdp to create the signal V_BKL_28V,
+ * this is connected to LED+ pin of the sharp panel. This GPIO
+ * is left enabled in the board file, and not passed to the panel
+ * as platform_data.
+ */
+ r = gpio_request_one(SDP3430_LCD_PANEL_BACKLIGHT_GPIO,
+ GPIOF_OUT_INIT_HIGH, "LCD Backlight");
if (r)
- printk(KERN_ERR "failed to get LCD control GPIOs\n");
-
-}
-
-static int sdp3430_panel_enable_lcd(struct omap_dss_device *dssdev)
-{
- gpio_direction_output(SDP3430_LCD_PANEL_ENABLE_GPIO, 1);
- gpio_direction_output(SDP3430_LCD_PANEL_BACKLIGHT_GPIO, 1);
-
- return 0;
-}
+ pr_err("failed to get LCD Backlight GPIO\n");
-static void sdp3430_panel_disable_lcd(struct omap_dss_device *dssdev)
-{
- gpio_direction_output(SDP3430_LCD_PANEL_ENABLE_GPIO, 0);
- gpio_direction_output(SDP3430_LCD_PANEL_BACKLIGHT_GPIO, 0);
}
static int sdp3430_panel_enable_tv(struct omap_dss_device *dssdev)
@@ -145,14 +133,20 @@ static void sdp3430_panel_disable_tv(struct omap_dss_device *dssdev)
{
}
+static struct panel_sharp_ls037v7dw01_data sdp3430_lcd_data = {
+ .resb_gpio = SDP3430_LCD_PANEL_ENABLE_GPIO,
+ .ini_gpio = -1,
+ .mo_gpio = -1,
+ .lr_gpio = -1,
+ .ud_gpio = -1,
+};
static struct omap_dss_device sdp3430_lcd_device = {
.name = "lcd",
.driver_name = "sharp_ls_panel",
.type = OMAP_DISPLAY_TYPE_DPI,
.phy.dpi.data_lines = 16,
- .platform_enable = sdp3430_panel_enable_lcd,
- .platform_disable = sdp3430_panel_disable_lcd,
+ .data = &sdp3430_lcd_data,
};
static struct tfp410_platform_data dvi_panel = {
The omap3430sdp board file currently requests gpios required by the sharp_ls dpi panel, and provides platform_enable/disable callbacks to configure them. These tasks have been moved to the sharp_ls panel driver itself and shouldn't be done in the board files. Remove the gpio requests and the platform callbacks from the board file. Add the gpio information to panel_sharp_ls037v7dw01_data so that it's passed to the panel driver. Out of sharp panel's configurable pins, all apart from resb_gpio are managed by a CPLD on the display and set to a default value. Only the configurable pin is passed to platform data. The backlight GPIO doesn't go directly to the sharp panel, it is used to set up a voltage supply which goes to the LED+ pin of the panel, hence it isn't passed to panel as platform data, and configured in the board file itself. The backlight used to previously toggle through the platform_enable/disable callbacks, but now it is always on. This needs to be revisited. Cc: Tony Lindgren <tony@atomide.com> Signed-off-by: Archit Taneja <archit@ti.com> --- arch/arm/mach-omap2/board-3430sdp.c | 42 +++++++++++++++-------------------- 1 file changed, 18 insertions(+), 24 deletions(-)