| Message ID | 1371630423-2481-2-git-send-email-eballetbo@iseebcn.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Hi Enric, On 06/19/2013 03:27 AM, Enric Balletbo i Serra wrote: > The IGEP COM AQUILA is industrial processors SODIMM module with > following highlights: > > o AM3352/AM3354/AM3358/AM3359 Texas Instruments processor > o Cortex-A8 ARM CPU > o 3.3 volts Inputs / Outputs use industrial > o 256 MB DDR3 SDRAM / 128 Megabytes FLASH > o MicroSD card reader on-board > o Ethernet controller on-board > o JTAG debug connector available > o Designed for industrial range purposes > > Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> > --- > arch/arm/boot/dts/am335x-igep0033.dtsi | 269 +++++++++++++++++++++++++++++++++ > 1 file changed, 269 insertions(+) > create mode 100644 arch/arm/boot/dts/am335x-igep0033.dtsi > > diff --git a/arch/arm/boot/dts/am335x-igep0033.dtsi b/arch/arm/boot/dts/am335x-igep0033.dtsi > new file mode 100644 > index 0000000..1d70141 > --- /dev/null > +++ b/arch/arm/boot/dts/am335x-igep0033.dtsi > @@ -0,0 +1,269 @@ > +/* > + * Copyright (C) 2013 ISEE 2007 SL - http://www.isee.biz/ > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > + */ > + > +/dts-v1/; > + > +#include "am33xx.dtsi" > + > +/ { > + cpus { > + cpu@0 { > + cpu0-supply = <&vdd1_reg>; > + }; > + }; > + > + memory { > + device_type = "memory"; > + reg = <0x80000000 0x10000000>; /* 256 MB */ > + }; > + > + am33xx_pinmux: pinmux@44e10800 { That node should be inside the ocp one since the control module is a regular IP connected to the OCP interconnect. > + pinctrl-names = "default"; > + > + i2c0_pins: pinmux_i2c0_pins { > + pinctrl-single,pins = < > + 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */ > + 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */ > + >; > + }; > + > + nandflash_pins: pinmux_nandflash_pins { > + pinctrl-single,pins = < > + 0x0 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */ > + 0x4 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */ > + 0x8 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */ > + 0xc (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */ > + 0x10 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */ > + 0x14 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */ > + 0x18 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */ > + 0x1c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */ > + 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */ > + 0x74 (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpio0_30 */ > + 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */ > + 0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */ > + 0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */ > + 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */ > + 0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */ > + >; > + }; > + > + uart0_pins: pinmux_uart0_pins { > + pinctrl-single,pins = < > + 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ > + 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ > + >; > + }; > + > + user_leds: pinmux_user_leds_pins { > + pinctrl-single,pins = < > + 0x5c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a7.gpio1_23 */ > + >; > + }; > + > + }; > + > + ocp { > + uart0: serial@44e09000 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart0_pins>; > + status = "okay"; > + }; > + > + i2c0: i2c@44e0b000 { > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c0_pins>; > + > + status = "okay"; > + clock-frequency = <400000>; > + > + tps: tps@2d { > + reg = <0x2d>; > + }; > + }; > + > + elm: elm@48080000 { > + status = "okay"; > + }; > + > + gpmc: gpmc@50000000 { > + pinctrl-names = "default"; > + pinctrl-0 = <&nandflash_pins>; > + > + status = "okay"; > + ranges = <0 0 0x08000000 0x10000000>; /* CS0: NAND */ > + > + nand@0,0 { > + reg = <0 0 0>; /* CS0, offset 0 */ > + nand-bus-width = <8>; > + ti,nand-ecc-opt = "bch8"; > + gpmc,device-nand = "true"; > + gpmc,device-width = <1>; > + gpmc,sync-clk-ps = <0>; > + gpmc,cs-on-ns = <0>; > + gpmc,cs-rd-off-ns = <44>; > + gpmc,cs-wr-off-ns = <44>; > + gpmc,adv-on-ns = <6>; > + gpmc,adv-rd-off-ns = <34>; > + gpmc,adv-wr-off-ns = <44>; > + gpmc,we-on-ns = <0>; > + gpmc,we-off-ns = <40>; > + gpmc,oe-on-ns = <0>; > + gpmc,oe-off-ns = <54>; > + gpmc,access-ns = <64>; > + gpmc,rd-cycle-ns = <82>; > + gpmc,wr-cycle-ns = <82>; > + gpmc,wait-on-read = "true"; > + gpmc,wait-on-write = "true"; > + gpmc,bus-turnaround-ns = <0>; > + gpmc,cycle2cycle-delay-ns = <0>; > + gpmc,clk-activation-ns = <0>; > + gpmc,wait-monitoring-ns = <0>; > + gpmc,wr-access-ns = <40>; > + gpmc,wr-data-mux-bus-ns = <0>; > + > + #address-cells = <1>; > + #size-cells = <1>; > + elm_id = <&elm>; > + > + /* MTD partition table */ > + partition@0 { > + label = "SPL"; > + reg = <0x00000000 0x000080000>; > + }; > + > + partition@1 { > + label = "U-boot"; > + reg = <0x00080000 0x001e0000>; > + }; > + > + partition@2 { > + label = "U-Boot Env"; > + reg = <0x00260000 0x00020000>; > + }; > + > + partition@3 { > + label = "Kernel"; > + reg = <0x00280000 0x00500000>; > + }; > + > + partition@4 { > + label = "File System"; > + reg = <0x00780000 0x0F880000>; > + }; > + }; > + }; > + }; > + > + leds { > + pinctrl-names = "default"; > + pinctrl-0 = <&user_leds>; > + > + compatible = "gpio-leds"; > + > + led@0 { > + label = "com:green:user"; > + gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>; > + default-state = "on"; > + }; > + }; > + > + > + vbat: fixedregulator@0 { > + compatible = "regulator-fixed"; > + regulator-name = "vbat"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-boot-on; > + }; > +}; > + > +#include "tps65910.dtsi" > + > +&tps { > + vcc1-supply = <&vbat>; > + vcc2-supply = <&vbat>; > + vcc3-supply = <&vbat>; > + vcc4-supply = <&vbat>; > + vcc5-supply = <&vbat>; > + vcc6-supply = <&vbat>; > + vcc7-supply = <&vbat>; > + vccio-supply = <&vbat>; > + > + regulators { > + vrtc_reg: regulator@0 { > + regulator-always-on; > + }; > + > + vio_reg: regulator@1 { > + regulator-always-on; > + }; > + > + vdd1_reg: regulator@2 { > + /* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */ > + regulator-name = "vdd_mpu"; > + regulator-min-microvolt = <912500>; > + regulator-max-microvolt = <1312500>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + vdd2_reg: regulator@3 { > + /* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */ > + regulator-name = "vdd_core"; > + regulator-min-microvolt = <912500>; > + regulator-max-microvolt = <1150000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + vdd3_reg: regulator@4 { > + regulator-always-on; > + }; > + > + vdig1_reg: regulator@5 { > + regulator-always-on; > + }; > + > + vdig2_reg: regulator@6 { > + regulator-always-on; > + }; > + > + vpll_reg: regulator@7 { > + regulator-always-on; > + }; > + > + vdac_reg: regulator@8 { > + regulator-always-on; > + }; > + > + vaux1_reg: regulator@9 { > + regulator-always-on; > + }; > + > + vaux2_reg: regulator@10 { > + regulator-always-on; > + }; > + > + vaux33_reg: regulator@11 { > + regulator-always-on; > + }; > + > + vmmc_reg: regulator@12 { > + regulator-always-on; > + }; > + }; > +}; > + > +&cpsw_emac0 { > + phy_id = <&davinci_mdio>, <0>; > +}; > + > +&cpsw_emac1 { > + phy_id = <&davinci_mdio>, <1>; > +}; > + > Otherwise, it looks good. Thanks, Benoit -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi, On Wed, Jun 19, 2013 at 12:46 PM, Benoit Cousson <b-cousson@ti.com> wrote: > Hi Enric, > > > On 06/19/2013 03:27 AM, Enric Balletbo i Serra wrote: >> >> The IGEP COM AQUILA is industrial processors SODIMM module with >> following highlights: >> >> o AM3352/AM3354/AM3358/AM3359 Texas Instruments processor >> o Cortex-A8 ARM CPU >> o 3.3 volts Inputs / Outputs use industrial >> o 256 MB DDR3 SDRAM / 128 Megabytes FLASH >> o MicroSD card reader on-board >> o Ethernet controller on-board >> o JTAG debug connector available >> o Designed for industrial range purposes >> >> Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> >> --- >> arch/arm/boot/dts/am335x-igep0033.dtsi | 269 >> +++++++++++++++++++++++++++++++++ >> 1 file changed, 269 insertions(+) >> create mode 100644 arch/arm/boot/dts/am335x-igep0033.dtsi >> >> diff --git a/arch/arm/boot/dts/am335x-igep0033.dtsi >> b/arch/arm/boot/dts/am335x-igep0033.dtsi >> new file mode 100644 >> index 0000000..1d70141 >> --- /dev/null >> +++ b/arch/arm/boot/dts/am335x-igep0033.dtsi >> @@ -0,0 +1,269 @@ >> +/* >> + * Copyright (C) 2013 ISEE 2007 SL - http://www.isee.biz/ >> + * >> + * This program is free software; you can redistribute it and/or modify >> + * it under the terms of the GNU General Public License version 2 as >> + * published by the Free Software Foundation. >> + */ >> + >> +/dts-v1/; >> + >> +#include "am33xx.dtsi" >> + >> +/ { >> + cpus { >> + cpu@0 { >> + cpu0-supply = <&vdd1_reg>; >> + }; >> + }; >> + >> + memory { >> + device_type = "memory"; >> + reg = <0x80000000 0x10000000>; /* 256 MB */ >> + }; >> + >> + am33xx_pinmux: pinmux@44e10800 { > > > That node should be inside the ocp one since the control module is a regular > IP connected to the OCP interconnect. > > > In fact, I don't think that there should be a definition of the On Chip Peripherals interconnect or any child node of the ocp in a DTS file. These should be defined in the included dtsi file since it will be common to all boards based on this SoC. DTS files that describe a board can reference these nodes defined in the dtsi and add their custom peripherals as childs of them. So, instead defining in the DTS: am33xx_pinmux: pinmux@44e10800 { ... }; gpmc: gpmc@50000000 { ... }; i2c0: i2c@44e0b000 { ... }; uart0: serial@44e09000 { .. }; It has to be defined as: &am33xx_pinmux { ... }; &gpmc { ... }; &i2c0 { ... } I'm looking at other am33xx dts such as am335x-bone.dts and am335x-evm.dts and I see that these define device nodes already defined in the included .dtsi which is wrong in my opinion. The OMAP{3,4,5} dtsi and dts do correctly and can be used as a reference on how the device nodes have to be defined and referenced. Best regards, Javier -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Javier, On 6/19/2013 8:32 AM, Javier Martinez Canillas wrote: > Hi, > > On Wed, Jun 19, 2013 at 12:46 PM, Benoit Cousson <b-cousson@ti.com> wrote: >> Hi Enric, >> >> >> On 06/19/2013 03:27 AM, Enric Balletbo i Serra wrote: >>> >>> The IGEP COM AQUILA is industrial processors SODIMM module with >>> following highlights: >>> >>> o AM3352/AM3354/AM3358/AM3359 Texas Instruments processor >>> o Cortex-A8 ARM CPU >>> o 3.3 volts Inputs / Outputs use industrial >>> o 256 MB DDR3 SDRAM / 128 Megabytes FLASH >>> o MicroSD card reader on-board >>> o Ethernet controller on-board >>> o JTAG debug connector available >>> o Designed for industrial range purposes >>> >>> Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> >>> --- >>> arch/arm/boot/dts/am335x-igep0033.dtsi | 269 >>> +++++++++++++++++++++++++++++++++ >>> 1 file changed, 269 insertions(+) >>> create mode 100644 arch/arm/boot/dts/am335x-igep0033.dtsi >>> >>> diff --git a/arch/arm/boot/dts/am335x-igep0033.dtsi >>> b/arch/arm/boot/dts/am335x-igep0033.dtsi >>> new file mode 100644 >>> index 0000000..1d70141 >>> --- /dev/null >>> +++ b/arch/arm/boot/dts/am335x-igep0033.dtsi >>> @@ -0,0 +1,269 @@ >>> +/* >>> + * Copyright (C) 2013 ISEE 2007 SL - http://www.isee.biz/ >>> + * >>> + * This program is free software; you can redistribute it and/or modify >>> + * it under the terms of the GNU General Public License version 2 as >>> + * published by the Free Software Foundation. >>> + */ >>> + >>> +/dts-v1/; >>> + >>> +#include "am33xx.dtsi" >>> + >>> +/ { >>> + cpus { >>> + cpu@0 { >>> + cpu0-supply = <&vdd1_reg>; >>> + }; >>> + }; >>> + >>> + memory { >>> + device_type = "memory"; >>> + reg = <0x80000000 0x10000000>; /* 256 MB */ >>> + }; >>> + >>> + am33xx_pinmux: pinmux@44e10800 { >> >> >> That node should be inside the ocp one since the control module is a regular >> IP connected to the OCP interconnect. >> >> >> > > In fact, I don't think that there should be a definition of the On > Chip Peripherals interconnect or any child node of the ocp in a DTS > file. > These should be defined in the included dtsi file since it will be > common to all boards based on this SoC. Well there is nothing wrong with that in the DTS theory, but I do agree that keeping these internal SoC details outside the board file is indeed much better. > DTS files that describe a board can reference these nodes defined in > the dtsi and add their custom peripherals as childs of them. > > So, instead defining in the DTS: > > am33xx_pinmux: pinmux@44e10800 { > ... > }; > > gpmc: gpmc@50000000 { > ... > }; > > i2c0: i2c@44e0b000 { > ... > }; > > uart0: serial@44e09000 { > .. > }; > > It has to be defined as: > > &am33xx_pinmux { > ... > }; > > &gpmc { > ... > }; > > &i2c0 { > ... > } > > I'm looking at other am33xx dts such as am335x-bone.dts and > am335x-evm.dts and I see that these define device nodes already > defined in the included .dtsi which is wrong in my opinion. > > The OMAP{3,4,5} dtsi and dts do correctly and can be used as a > reference on how the device nodes have to be defined and referenced. Good point, we should potentially clean the am33xx files to make then consistent with other OMAP stuff. Thanks, Benoit -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/arch/arm/boot/dts/am335x-igep0033.dtsi b/arch/arm/boot/dts/am335x-igep0033.dtsi new file mode 100644 index 0000000..1d70141 --- /dev/null +++ b/arch/arm/boot/dts/am335x-igep0033.dtsi @@ -0,0 +1,269 @@ +/* + * Copyright (C) 2013 ISEE 2007 SL - http://www.isee.biz/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/dts-v1/; + +#include "am33xx.dtsi" + +/ { + cpus { + cpu@0 { + cpu0-supply = <&vdd1_reg>; + }; + }; + + memory { + device_type = "memory"; + reg = <0x80000000 0x10000000>; /* 256 MB */ + }; + + am33xx_pinmux: pinmux@44e10800 { + pinctrl-names = "default"; + + i2c0_pins: pinmux_i2c0_pins { + pinctrl-single,pins = < + 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */ + 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */ + >; + }; + + nandflash_pins: pinmux_nandflash_pins { + pinctrl-single,pins = < + 0x0 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */ + 0x4 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */ + 0x8 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */ + 0xc (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */ + 0x10 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */ + 0x14 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */ + 0x18 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */ + 0x1c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */ + 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */ + 0x74 (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpio0_30 */ + 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */ + 0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */ + 0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */ + 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */ + 0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */ + >; + }; + + uart0_pins: pinmux_uart0_pins { + pinctrl-single,pins = < + 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ + 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ + >; + }; + + user_leds: pinmux_user_leds_pins { + pinctrl-single,pins = < + 0x5c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a7.gpio1_23 */ + >; + }; + + }; + + ocp { + uart0: serial@44e09000 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins>; + status = "okay"; + }; + + i2c0: i2c@44e0b000 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + + status = "okay"; + clock-frequency = <400000>; + + tps: tps@2d { + reg = <0x2d>; + }; + }; + + elm: elm@48080000 { + status = "okay"; + }; + + gpmc: gpmc@50000000 { + pinctrl-names = "default"; + pinctrl-0 = <&nandflash_pins>; + + status = "okay"; + ranges = <0 0 0x08000000 0x10000000>; /* CS0: NAND */ + + nand@0,0 { + reg = <0 0 0>; /* CS0, offset 0 */ + nand-bus-width = <8>; + ti,nand-ecc-opt = "bch8"; + gpmc,device-nand = "true"; + gpmc,device-width = <1>; + gpmc,sync-clk-ps = <0>; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <44>; + gpmc,cs-wr-off-ns = <44>; + gpmc,adv-on-ns = <6>; + gpmc,adv-rd-off-ns = <34>; + gpmc,adv-wr-off-ns = <44>; + gpmc,we-on-ns = <0>; + gpmc,we-off-ns = <40>; + gpmc,oe-on-ns = <0>; + gpmc,oe-off-ns = <54>; + gpmc,access-ns = <64>; + gpmc,rd-cycle-ns = <82>; + gpmc,wr-cycle-ns = <82>; + gpmc,wait-on-read = "true"; + gpmc,wait-on-write = "true"; + gpmc,bus-turnaround-ns = <0>; + gpmc,cycle2cycle-delay-ns = <0>; + gpmc,clk-activation-ns = <0>; + gpmc,wait-monitoring-ns = <0>; + gpmc,wr-access-ns = <40>; + gpmc,wr-data-mux-bus-ns = <0>; + + #address-cells = <1>; + #size-cells = <1>; + elm_id = <&elm>; + + /* MTD partition table */ + partition@0 { + label = "SPL"; + reg = <0x00000000 0x000080000>; + }; + + partition@1 { + label = "U-boot"; + reg = <0x00080000 0x001e0000>; + }; + + partition@2 { + label = "U-Boot Env"; + reg = <0x00260000 0x00020000>; + }; + + partition@3 { + label = "Kernel"; + reg = <0x00280000 0x00500000>; + }; + + partition@4 { + label = "File System"; + reg = <0x00780000 0x0F880000>; + }; + }; + }; + }; + + leds { + pinctrl-names = "default"; + pinctrl-0 = <&user_leds>; + + compatible = "gpio-leds"; + + led@0 { + label = "com:green:user"; + gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + }; + + + vbat: fixedregulator@0 { + compatible = "regulator-fixed"; + regulator-name = "vbat"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + }; +}; + +#include "tps65910.dtsi" + +&tps { + vcc1-supply = <&vbat>; + vcc2-supply = <&vbat>; + vcc3-supply = <&vbat>; + vcc4-supply = <&vbat>; + vcc5-supply = <&vbat>; + vcc6-supply = <&vbat>; + vcc7-supply = <&vbat>; + vccio-supply = <&vbat>; + + regulators { + vrtc_reg: regulator@0 { + regulator-always-on; + }; + + vio_reg: regulator@1 { + regulator-always-on; + }; + + vdd1_reg: regulator@2 { + /* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */ + regulator-name = "vdd_mpu"; + regulator-min-microvolt = <912500>; + regulator-max-microvolt = <1312500>; + regulator-boot-on; + regulator-always-on; + }; + + vdd2_reg: regulator@3 { + /* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */ + regulator-name = "vdd_core"; + regulator-min-microvolt = <912500>; + regulator-max-microvolt = <1150000>; + regulator-boot-on; + regulator-always-on; + }; + + vdd3_reg: regulator@4 { + regulator-always-on; + }; + + vdig1_reg: regulator@5 { + regulator-always-on; + }; + + vdig2_reg: regulator@6 { + regulator-always-on; + }; + + vpll_reg: regulator@7 { + regulator-always-on; + }; + + vdac_reg: regulator@8 { + regulator-always-on; + }; + + vaux1_reg: regulator@9 { + regulator-always-on; + }; + + vaux2_reg: regulator@10 { + regulator-always-on; + }; + + vaux33_reg: regulator@11 { + regulator-always-on; + }; + + vmmc_reg: regulator@12 { + regulator-always-on; + }; + }; +}; + +&cpsw_emac0 { + phy_id = <&davinci_mdio>, <0>; +}; + +&cpsw_emac1 { + phy_id = <&davinci_mdio>, <1>; +}; +
The IGEP COM AQUILA is industrial processors SODIMM module with following highlights: o AM3352/AM3354/AM3358/AM3359 Texas Instruments processor o Cortex-A8 ARM CPU o 3.3 volts Inputs / Outputs use industrial o 256 MB DDR3 SDRAM / 128 Megabytes FLASH o MicroSD card reader on-board o Ethernet controller on-board o JTAG debug connector available o Designed for industrial range purposes Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> --- arch/arm/boot/dts/am335x-igep0033.dtsi | 269 +++++++++++++++++++++++++++++++++ 1 file changed, 269 insertions(+) create mode 100644 arch/arm/boot/dts/am335x-igep0033.dtsi