@@ -179,6 +179,8 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
omap2420-n810-wimax.dtb \
omap3430-sdp.dtb \
omap3-beagle.dtb \
+ omap3-cm-t3517.dtb \
+ omap3-sbc-t3517.dtb \
omap3-cm-t3530.dtb \
omap3-sbc-t3530.dtb \
omap3-cm-t3730.dtb \
new file mode 100644
@@ -0,0 +1,136 @@
+/*
+ * Support for CompuLab CM-T3517
+ */
+/dts-v1/;
+
+#include "am3517.dtsi"
+#include "omap3-cm-t3x.dtsi"
+
+/ {
+ model = "CompuLab CM-T3517";
+ compatible = "compulab,omap3-cm-t3517", "ti,am3517", "ti,omap3";
+
+ vmmc: regulator-vmmc {
+ compatible = "regulator-fixed";
+ regulator-name = "vmmc";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ wl12xx_vmmc2: wl12xx_vmmc2 {
+ compatible = "regulator-fixed";
+ regulator-name = "vw1271";
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &wl12xx_wkup_pins
+ &wl12xx_core_pins
+ >;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&gpio1 6 GPIO_ACTIVE_HIGH >; /* gpio6 */
+ startup-delay-us = <20000>;
+ enable-active-high;
+ };
+
+ wl12xx_vaux2: wl12xx_vaux2 {
+ compatible = "regulator-fixed";
+ regulator-name = "vwl1271_vaux2";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+};
+
+&omap3_pmx_wkup {
+
+ wl12xx_wkup_pins: pinmux_wl12xx_wkup_pins {
+ pinctrl-single,pins = <
+ OMAP3_WKUP_IOPAD(0x2a0e, PIN_OUTPUT | MUX_MODE4) /* sys_boot2.gpio_4 */
+ OMAP3_WKUP_IOPAD(0x2a12, PIN_OUTPUT | MUX_MODE4) /* sys_boot4.gpio_6 */
+ >;
+ };
+};
+
+&omap3_pmx_core {
+
+ phy1_reset_pins: pinmux_hsusb1_phy_reset_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE4) /* uart2_tx.gpio_146 */
+ >;
+ };
+
+ phy2_reset_pins: pinmux_hsusb2_phy_reset_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x217a, PIN_OUTPUT | MUX_MODE4) /* uart2_rx.gpio_147 */
+ >;
+ };
+
+ otg_drv_vbus: pinmux_otg_drv_vbus {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x2210, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii_50Mhz_clk.usb0_drvvbus */
+ >;
+ };
+
+ mmc2_pins: pinmux_mmc2_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */
+ OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */
+ OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */
+ OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */
+ OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */
+ OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */
+ >;
+ };
+
+ wl12xx_core_pins: pinmux_wl12xx_core_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x20b8, PIN_OUTPUT | MUX_MODE4) /* gpmc_ncs5.gpio_56 */
+ OMAP3_CORE1_IOPAD(0x2176, PIN_INPUT_PULLUP | MUX_MODE4) /* uart2_rts.gpio_145 */
+ >;
+ };
+
+ usb_hub_pins: pinmux_usb_hub_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x2184, PIN_OUTPUT | MUX_MODE4) /* mcbsp4_clkx.gpio_152 - USB HUB RST */
+ >;
+ };
+};
+
+&hsusb1_phy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&phy1_reset_pins>;
+ reset-gpios = <&gpio5 18 GPIO_ACTIVE_LOW>;
+};
+
+&hsusb2_phy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&phy2_reset_pins>;
+ reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>;
+};
+
+&davinci_emac {
+ status = "okay";
+};
+
+&davinci_mdio {
+ status = "okay";
+};
+
+&am35x_otg_hs {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&otg_drv_vbus>;
+};
+
+&mmc1 {
+ vmmc-supply = <&vmmc>;
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_pins>;
+ vmmc-supply = <&wl12xx_vmmc2>;
+ vmmc_aux-supply = <&wl12xx_vaux2>;
+ non-removable;
+ bus-width = <4>;
+ cap-power-off-card;
+};
new file mode 100644
@@ -0,0 +1,43 @@
+/*
+ * Suppport for CompuLab SBC-T3517 with CM-T3517
+ */
+
+#include "omap3-cm-t3517.dts"
+#include "omap3-sb-t35.dtsi"
+
+/ {
+ model = "CompuLab SBC-T3517 with CM-T3517";
+ compatible = "compulab,omap3-sbc-t3517", "compulab,omap3-cm-t3517", "ti,am3517", "ti,omap3";
+};
+
+&omap3_pmx_core {
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &sb_t35_usb_hub_pins
+ &usb_hub_pins
+ >;
+
+ mmc1_aux_pins: pinmux_mmc1_aux_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x20c0, PIN_INPUT_PULLUP | MUX_MODE4) /* gpmc_clk.gpio_59 */
+ OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT_PULLUP | MUX_MODE4) /* uart2_cts.gpio_144 */
+ >;
+ };
+
+ sb_t35_usb_hub_pins: pinmux_sb_t35_usb_hub_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x21ec, PIN_OUTPUT | MUX_MODE4) /* ccdc_wen.gpio_98 - SB-T35 USB HUB RST */
+ >;
+ };
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &mmc1_pins
+ &mmc1_aux_pins
+ >;
+
+ wp-gpios = <&gpio2 27 GPIO_ACTIVE_HIGH>; /* gpio_59 */
+ cd-gpios = <&gpio5 16 GPIO_ACTIVE_HIGH>; /* gpio_144 */
+};
@@ -165,7 +165,7 @@ static struct emac_platform_data am35xx_emac_pdata = {
.interrupt_disable = am35xx_disable_emac_int,
};
-static void __init am3517_evm_legacy_init(void)
+static void __init am35xx_emac_reset(void)
{
u32 v;
@@ -174,6 +174,41 @@ static void __init am3517_evm_legacy_init(void)
omap_ctrl_writel(v, AM35XX_CONTROL_IP_SW_RESET);
omap_ctrl_readl(AM35XX_CONTROL_IP_SW_RESET); /* OCP barrier */
}
+
+static struct gpio cm_t3517_wlan_gpios[] __initdata = {
+ { 56, GPIOF_OUT_INIT_HIGH, "wlan pwr" },
+ { 4, GPIOF_OUT_INIT_HIGH, "xcvr noe" },
+};
+
+static void __init omap3_sbc_t3517_wifi_init(void)
+{
+ int err = gpio_request_array(cm_t3517_wlan_gpios,
+ ARRAY_SIZE(cm_t3517_wlan_gpios));
+ if (err) {
+ pr_err("SBC-T3517: wl12xx gpios request failed: %d\n", err);
+ return;
+ }
+
+ gpio_export(cm_t3517_wlan_gpios[0].gpio, 0);
+ gpio_export(cm_t3517_wlan_gpios[1].gpio, 0);
+
+ msleep(100);
+ gpio_set_value(cm_t3517_wlan_gpios[1].gpio, 0);
+}
+
+static void __init omap3_sbc_t3517_legacy_init(void)
+{
+ am35xx_emac_reset();
+ hsmmc2_internal_input_clk();
+ omap3_sbc_t3517_wifi_init();
+ legacy_init_wl12xx(WL12XX_REFCLOCK_38, 0, 145);
+ omap_ads7846_init(1, 57, 0, NULL);
+}
+
+static void __init am3517_evm_legacy_init(void)
+{
+ am35xx_emac_reset();
+}
#endif /* CONFIG_ARCH_OMAP3 */
#ifdef CONFIG_ARCH_OMAP4
@@ -263,6 +298,7 @@ struct of_dev_auxdata omap_auxdata_lookup[] __initdata = {
*/
static struct pdata_init pdata_quirks[] __initdata = {
#ifdef CONFIG_ARCH_OMAP3
+ { "compulab,omap3-sbc-t3517", omap3_sbc_t3517_legacy_init, },
{ "compulab,omap3-sbc-t3530", omap3_sbc_t3530_legacy_init, },
{ "compulab,omap3-sbc-t3730", omap3_sbc_t3730_legacy_init, },
{ "nokia,omap3-n900", hsmmc2_internal_input_clk, },
Add support for CM-T3517 CoM and SBC-T3517 board. reused common support for sbc-t3x boards (omap3-cm-t3x.dtsi, omap3-sb-t35.dtsi): * SB-T35 baseboard eth * MMC1, UART3 * HS USB Port 1/2 * I2C1/3 * Heartbit led Added basic support for: * MMC1 wp/cd signals * CM-T3517 Usb Hub * WL12xx WiFi chip * Davinci EMAC * AM35X OTG Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il> --- arch/arm/boot/dts/Makefile | 2 + arch/arm/boot/dts/omap3-cm-t3517.dts | 136 +++++++++++++++++++++++++++++++++ arch/arm/boot/dts/omap3-sbc-t3517.dts | 43 ++++++++++ arch/arm/mach-omap2/pdata-quirks.c | 38 +++++++++- 4 files changed, 218 insertions(+), 1 deletions(-) create mode 100644 arch/arm/boot/dts/omap3-cm-t3517.dts create mode 100644 arch/arm/boot/dts/omap3-sbc-t3517.dts