| Message ID | 1399591234-13089-7-git-send-email-afenkart@gmail.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On Friday 09 May 2014 04:50 AM, Andreas Fenkart wrote: > The am335x can't detect pending cirq in PM runtime suspend. > This patch reconfigures dat1 as a GPIO before going to suspend. > SDIO interrupts are detected with the GPIO, the GPIO will only wake > the module from suspend, SDIO irq detection will still happen through the > IP block. > > Idea of remuxing the pins by Tony Lindgren. Code contributions from > Tony Lindgren and Balaji T K <balajitk@ti.com> > > Signed-off-by: Andreas Fenkart <afenkart@gmail.com> > Signed-off-by: Tony Lindgren <tony@atomide.com> > > Conflicts: > drivers/mmc/host/omap_hsmmc.c Remove above 2 lines Acked-by: Balaji T K <balajitk@ti.com> > > diff --git a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt > index ce80561..946bc5f 100644 > --- a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt > +++ b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt > @@ -56,3 +56,56 @@ Examples: > &edma 25>; > dma-names = "tx", "rx"; > }; > + > +[workaround for missing swakeup on am33xx] > + > +This SOC is missing the swakeup line, it will not detect SDIO irq > +while in suspend. > + > + ------ > + | PRCM | > + ------ > + ^ | > + swakeup | | fclk > + | v > + ------ ------- ----- > + | card | -- CIRQ --> | hsmmc | -- IRQ --> | CPU | > + ------ ------- ----- > + > +In suspend the fclk is off and the module is disfunctional. Even register reads > +will fail. A small logic in the host will request fclk restore, when an > +external event is detected. Once the clock is restored, the host detects the > +event normally. Since am33xx doesn't have this line it never wakes from > +suspend. > + > +The workaround is to reconfigure the dat1 line as a GPIO upon suspend. To make > +this work, we need to set the named pinctrl states "default" and "idle". > +Prepare idle to remux dat1 as a gpio, and default to remux it back as sdio > +dat1. The MMC driver will then toggle between idle and default state during > +runtime. > + > +In summary: > +1. select matching 'compatible' section, see example below. > +2. specify pinctrl states "default" and "idle", "sleep" is optional. > +3. specify the gpio irq used for detecting sdio irq in suspend > + > +If configuration is incomplete, a warning message is emitted "falling back to > +polling". Also check the "sdio irq mode" in /sys/kernel/debug/mmc0/regs. Mind > +not every application needs SDIO irq, e.g. MMC cards. > + > + mmc1: mmc@48060100 { > + compatible = "ti,am33xx-hsmmc"; > + ... > + pinctrl-names = "default", "idle", "sleep" > + pinctrl-0 = <&mmc1_pins>; > + pinctrl-1 = <&mmc1_idle>; > + pinctrl-2 = <&mmc1_sleep>; > + ... > + interrupts-extended = <&intc 64 &gpio2 28 0>; > + }; > + > + mmc1_idle : pinmux_cirq_pin { > + pinctrl-single,pins = < > + 0x0f8 0x3f /* GPIO2_28 */ > + >; > + }; > diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c > index 5a321f98..497b2fc 100644 > --- a/drivers/mmc/host/omap_hsmmc.c > +++ b/drivers/mmc/host/omap_hsmmc.c > @@ -1782,15 +1782,25 @@ static int omap_hsmmc_configure_wake_irq(struct omap_hsmmc_host *host) > * and need to remux SDIO DAT1 to GPIO for wake-up from idle. > */ > if (host->pdata->controller_flags & OMAP_HSMMC_SWAKEUP_MISSING) { > - ret = -ENODEV; > - devm_free_irq(host->dev, host->wake_irq, host); > - goto err; > + if (IS_ERR(host->dev->pins->default_state)) { > + dev_info(host->dev, "missing default pinctrl state\n"); > + ret = -EINVAL; > + goto err_free_irq; > + } > + > + if (IS_ERR(host->dev->pins->idle_state)) { > + dev_info(host->dev, "missing idle pinctrl state\n"); > + ret = -EINVAL; > + goto err_free_irq; > + } > } > > OMAP_HSMMC_WRITE(host->base, HCTL, > OMAP_HSMMC_READ(host->base, HCTL) | IWE); > return 0; > > +err_free_irq: > + devm_free_irq(host->dev, host->wake_irq, host); > err: > dev_warn(host->dev, "no SDIO IRQ support, falling back to polling\n"); > host->wake_irq = 0; > -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt index ce80561..946bc5f 100644 --- a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt +++ b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt @@ -56,3 +56,56 @@ Examples: &edma 25>; dma-names = "tx", "rx"; }; + +[workaround for missing swakeup on am33xx] + +This SOC is missing the swakeup line, it will not detect SDIO irq +while in suspend. + + ------ + | PRCM | + ------ + ^ | + swakeup | | fclk + | v + ------ ------- ----- + | card | -- CIRQ --> | hsmmc | -- IRQ --> | CPU | + ------ ------- ----- + +In suspend the fclk is off and the module is disfunctional. Even register reads +will fail. A small logic in the host will request fclk restore, when an +external event is detected. Once the clock is restored, the host detects the +event normally. Since am33xx doesn't have this line it never wakes from +suspend. + +The workaround is to reconfigure the dat1 line as a GPIO upon suspend. To make +this work, we need to set the named pinctrl states "default" and "idle". +Prepare idle to remux dat1 as a gpio, and default to remux it back as sdio +dat1. The MMC driver will then toggle between idle and default state during +runtime. + +In summary: +1. select matching 'compatible' section, see example below. +2. specify pinctrl states "default" and "idle", "sleep" is optional. +3. specify the gpio irq used for detecting sdio irq in suspend + +If configuration is incomplete, a warning message is emitted "falling back to +polling". Also check the "sdio irq mode" in /sys/kernel/debug/mmc0/regs. Mind +not every application needs SDIO irq, e.g. MMC cards. + + mmc1: mmc@48060100 { + compatible = "ti,am33xx-hsmmc"; + ... + pinctrl-names = "default", "idle", "sleep" + pinctrl-0 = <&mmc1_pins>; + pinctrl-1 = <&mmc1_idle>; + pinctrl-2 = <&mmc1_sleep>; + ... + interrupts-extended = <&intc 64 &gpio2 28 0>; + }; + + mmc1_idle : pinmux_cirq_pin { + pinctrl-single,pins = < + 0x0f8 0x3f /* GPIO2_28 */ + >; + }; diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c index 5a321f98..497b2fc 100644 --- a/drivers/mmc/host/omap_hsmmc.c +++ b/drivers/mmc/host/omap_hsmmc.c @@ -1782,15 +1782,25 @@ static int omap_hsmmc_configure_wake_irq(struct omap_hsmmc_host *host) * and need to remux SDIO DAT1 to GPIO for wake-up from idle. */ if (host->pdata->controller_flags & OMAP_HSMMC_SWAKEUP_MISSING) { - ret = -ENODEV; - devm_free_irq(host->dev, host->wake_irq, host); - goto err; + if (IS_ERR(host->dev->pins->default_state)) { + dev_info(host->dev, "missing default pinctrl state\n"); + ret = -EINVAL; + goto err_free_irq; + } + + if (IS_ERR(host->dev->pins->idle_state)) { + dev_info(host->dev, "missing idle pinctrl state\n"); + ret = -EINVAL; + goto err_free_irq; + } } OMAP_HSMMC_WRITE(host->base, HCTL, OMAP_HSMMC_READ(host->base, HCTL) | IWE); return 0; +err_free_irq: + devm_free_irq(host->dev, host->wake_irq, host); err: dev_warn(host->dev, "no SDIO IRQ support, falling back to polling\n"); host->wake_irq = 0;