@@ -29,10 +29,9 @@
/**
* omap_control_pcie_pcs - set the PCS delay count
* @dev: the control module device
- * @id: index of the pcie PHY (should be 1 or 2)
* @delay: 8 bit delay value
*/
-void omap_control_pcie_pcs(struct device *dev, u8 id, u8 delay)
+void omap_control_pcie_pcs(struct device *dev, u8 delay)
{
u32 val;
struct omap_control_phy *control_phy;
@@ -55,8 +54,8 @@ void omap_control_pcie_pcs(struct device *dev, u8 id, u8 delay)
val = readl(control_phy->pcie_pcs);
val &= ~(OMAP_CTRL_PCIE_PCS_MASK <<
- (id * OMAP_CTRL_PCIE_PCS_DELAY_COUNT_SHIFT));
- val |= delay << (id * OMAP_CTRL_PCIE_PCS_DELAY_COUNT_SHIFT);
+ OMAP_CTRL_PCIE_PCS_DELAY_COUNT_SHIFT);
+ val |= (delay << OMAP_CTRL_PCIE_PCS_DELAY_COUNT_SHIFT);
writel(val, control_phy->pcie_pcs);
}
EXPORT_SYMBOL_GPL(omap_control_pcie_pcs);
@@ -82,7 +82,6 @@ struct ti_pipe3 {
struct clk *refclk;
struct clk *div_clk;
struct pipe3_dpll_map *dpll_map;
- u8 id;
};
static struct pipe3_dpll_map dpll_map_usb[] = {
@@ -217,8 +216,13 @@ static int ti_pipe3_init(struct phy *x)
u32 val;
int ret = 0;
+ /*
+ * Set pcie_pcs register to 0x96 for proper functioning of phy
+ * as recommended in AM572x TRM SPRUHZ6, section 18.5.2.2, table
+ * 18-1804.
+ */
if (of_device_is_compatible(phy->dev->of_node, "ti,phy-pipe3-pcie")) {
- omap_control_pcie_pcs(phy->control_dev, phy->id, 0xF1);
+ omap_control_pcie_pcs(phy->control_dev, 0x96);
return 0;
}
@@ -347,8 +351,6 @@ static int ti_pipe3_probe(struct platform_device *pdev)
}
if (of_device_is_compatible(node, "ti,phy-pipe3-pcie")) {
- if (of_property_read_u8(node, "id", &phy->id) < 0)
- phy->id = 1;
clk = devm_clk_get(phy->dev, "dpll_ref");
if (IS_ERR(clk)) {
@@ -66,7 +66,7 @@ enum omap_control_usb_mode {
#define OMAP_CTRL_PIPE3_PHY_TX_RX_POWEROFF 0x0
#define OMAP_CTRL_PCIE_PCS_MASK 0xff
-#define OMAP_CTRL_PCIE_PCS_DELAY_COUNT_SHIFT 0x8
+#define OMAP_CTRL_PCIE_PCS_DELAY_COUNT_SHIFT 16
#define OMAP_CTRL_USB2_PHY_PD BIT(28)
@@ -79,7 +79,7 @@ enum omap_control_usb_mode {
void omap_control_phy_power(struct device *dev, int on);
void omap_control_usb_set_mode(struct device *dev,
enum omap_control_usb_mode mode);
-void omap_control_pcie_pcs(struct device *dev, u8 id, u8 delay);
+void omap_control_pcie_pcs(struct device *dev, u8 delay);
#else
static inline void omap_control_phy_power(struct device *dev, int on)
@@ -91,7 +91,7 @@ static inline void omap_control_usb_set_mode(struct device *dev,
{
}
-static inline void omap_control_pcie_pcs(struct device *dev, u8 id, u8 delay)
+static inline void omap_control_pcie_pcs(struct device *dev, u8 delay)
{
}
#endif
Prior to DRA74x silicon rev 1.1, pcie_pcs register bits 8-15 and bits 16-23 were used to configure RC delay count for phy1 and phy2 respectively. phyid was used as index to distinguish the phys and to configure the delay values appropriately. As of DRA74x silicon rev 1.1, pcie_pcs register definition has changed. Bits 16-23 are used to configure delay values for *both* phy1 and phy2. Hence phyid is no longer required. So, drop id field from ti_pipe3 structure and its subsequent references for configuring pcie_pcs register. Also, pcie_pcs register now needs to be configured with delay value of 0x96 at bit positions 16-23. See register description of CTRL_CORE_PCIE_PCS in ARM572x TRM, SPRUHZ6, October 2014, section 18.5.2.2, table 18-1804. This is needed to ensure Gen2 cards are enumerated consistently. DRA72x silicon behaves same way as DRA74x rev 1.1 as far as this functionality is considered. Test results on DRA74x and DRA72x EVMs: Before patch ------------ DRA74x ES 1.0: Gen1 cards work, Gen2 cards do not work (expected result due to silicon errata) DRA74x ES 1.1: Gen1 cards work, Gen2 cards do not work sometimes due to incorrect programming of register DRA72x: Gen1 cards work, Gen2 cards do not work sometimes due to incorrect programming of register After patch ----------- DRA74x ES 1.0: Gen1 cards work, Gen2 cards do not work (expected result due to silicon errata) DRA74x ES 1.1: Gen1 cards work, Gen2 cards work consistently. DRA72x: Gen1 and Gen2 cards enumerate consistently. Signed-off-by: Vignesh R <vigneshr@ti.com> --- drivers/phy/phy-omap-control.c | 7 +++---- drivers/phy/phy-ti-pipe3.c | 10 ++++++---- include/linux/phy/omap_control_phy.h | 6 +++--- 3 files changed, 12 insertions(+), 11 deletions(-)