@@ -21,6 +21,7 @@
#include <linux/leds.h>
#include <linux/scatterlist.h>
#include <linux/log2.h>
+#include <linux/regulator/consumer.h>
#include <linux/mmc/card.h>
#include <linux/mmc/host.h>
@@ -523,6 +524,105 @@ u32 mmc_vddrange_to_ocrmask(int vdd_min,
}
EXPORT_SYMBOL(mmc_vddrange_to_ocrmask);
+#ifdef CONFIG_REGULATOR
+
+/**
+ * mmc_regulator_get_ocrmask - return mask of supported voltages
+ * @supply: regulator to use
+ *
+ * This returns either a negative errno, or a mask of voltages that
+ * can be provided to MMC/SD/SDIO devices using the specified voltage
+ * regulator. This would normally be called before registering the
+ * MMC host adapter.
+ */
+int mmc_regulator_get_ocrmask(struct regulator *supply)
+{
+ int result = 0;
+ int count;
+ int i;
+
+ count = regulator_count_voltages(supply);
+ if (count < 0)
+ return count;
+
+ for (i = 0; i < count; i++) {
+ int vdd_uV;
+ int vdd_mV;
+
+ vdd_uV = regulator_list_voltage(supply, i);
+ if (vdd_uV <= 0)
+ continue;
+
+ vdd_mV = vdd_uV / 1000;
+ result |= mmc_vddrange_to_ocrmask(vdd_mV, vdd_mV);
+ }
+
+ return result;
+}
+EXPORT_SYMBOL(mmc_regulator_get_ocrmask);
+
+/**
+ * mmc_regulator_set_ocr - set regulator to match host->ios voltage
+ * @vdd_bit: zero for power off, else a bit number (host->ios.vdd)
+ * @supply: regulator to use
+ *
+ * Returns zero on success, else negative errno.
+ *
+ * MMC host drivers may use this to enable or disable a regulator using
+ * a particular supply voltage. This would normally be called from the
+ * set_ios() method.
+ */
+int mmc_regulator_set_ocr(struct regulator *supply, unsigned short vdd_bit)
+{
+ int result = 0;
+ int min_uV, max_uV;
+ int enabled;
+
+ enabled = regulator_is_enabled(supply);
+ if (enabled < 0)
+ return enabled;
+
+ if (vdd_bit) {
+ int tmp;
+ int voltage;
+
+ /* REVISIT mmc_vddrange_to_ocrmask() may have set some
+ * bits this regulator doesn't quite support ... don't
+ * be too picky, most cards and regulators are OK with
+ * a 0.1V range goof (it's a small error percentage).
+ */
+ tmp = vdd_bit - ilog2(MMC_VDD_165_195);
+ if (tmp == 0) {
+ min_uV = 1650 * 1000;
+ max_uV = 1950 * 1000;
+ } else {
+ min_uV = 1900 * 1000 + tmp * 100 * 1000;
+ max_uV = min_uV + 100 * 1000;
+ }
+
+ /* avoid needless changes to this voltage; the regulator
+ * might not allow this operation
+ */
+ voltage = regulator_get_voltage(supply);
+ if (voltage < 0)
+ result = voltage;
+ else if (voltage < min_uV || voltage > max_uV)
+ result = regulator_set_voltage(supply, min_uV, max_uV);
+ else
+ result = 0;
+
+ if (result == 0 && !enabled)
+ result = regulator_enable(supply);
+ } else if (enabled) {
+ result = regulator_disable(supply);
+ }
+
+ return result;
+}
+EXPORT_SYMBOL(mmc_regulator_set_ocr);
+
+#endif
+
/*
* Mask off any voltages we don't support and select
* the lowest voltage
@@ -192,5 +192,10 @@ static inline void mmc_signal_sdio_irq(s
wake_up_process(host->sdio_irq_thread);
}
+struct regulator;
+
+int mmc_regulator_get_ocrmask(struct regulator *supply);
+int mmc_regulator_set_ocr(struct regulator *supply, unsigned short vdd_bit);
+
#endif