@@ -1089,7 +1089,7 @@ static int _read_hardreset(struct omap_hwmod *oh, const char *name)
}
/**
- * _reset - reset an omap_hwmod
+ * _ocp_softreset - reset an omap_hwmod via the OCP_SYSCONFIG bit
* @oh: struct omap_hwmod *
*
* Resets an omap_hwmod @oh via the OCP_SYSCONFIG bit. hwmod must be
@@ -1098,12 +1098,13 @@ static int _read_hardreset(struct omap_hwmod *oh, const char *name)
* the module did not reset in time, or 0 upon success.
*
* In OMAP3 a specific SYSSTATUS register is used to get the reset status.
- * Starting in OMAP4, some IPs does not have SYSSTATUS register and instead
+ * Starting in OMAP4, some IPs do not have SYSSTATUS registers and instead
* use the SYSCONFIG softreset bit to provide the status.
*
- * Note that some IP like McBSP does have a reset control but no reset status.
+ * Note that some IP like McBSP do have reset control but don't have
+ * reset status.
*/
-static int _reset(struct omap_hwmod *oh)
+static int _ocp_softreset(struct omap_hwmod *oh)
{
u32 v;
int c = 0;
@@ -1124,7 +1125,7 @@ static int _reset(struct omap_hwmod *oh)
if (oh->flags & HWMOD_CONTROL_OPT_CLKS_IN_RESET)
_enable_optional_clocks(oh);
- pr_debug("omap_hwmod: %s: resetting\n", oh->name);
+ pr_debug("omap_hwmod: %s: resetting via OCP SOFTRESET\n", oh->name);
v = oh->_sysc_cache;
ret = _set_softreset(oh, &v);
@@ -1164,6 +1165,33 @@ dis_opt_clks:
}
/**
+ * _reset - reset an omap_hwmod
+ * @oh: struct omap_hwmod *
+ *
+ * Resets an omap_hwmod @oh. The default software reset mechanism for
+ * most OMAP IP blocks is triggered via the OCP_SYSCONFIG.SOFTRESET
+ * bit. However, some hwmods cannot be reset via this method: some
+ * are not targets and therefore have no OCP header registers to
+ * access; others (like the IVA) have idiosyncratic reset sequences.
+ * So for these relatively rare cases, custom reset code can be
+ * supplied in the struct omap_hwmod_class .reset function pointer.
+ * Passes along the return value from either _reset() or the custom
+ * reset function - these must return -EINVAL if the hwmod cannot be
+ * reset this way or if the hwmod is in the wrong state, -ETIMEDOUT if
+ * the module did not reset in time, or 0 upon success.
+ */
+static int _reset(struct omap_hwmod *oh)
+{
+ int ret;
+
+ pr_debug("omap_hwmod: %s: resetting\n", oh->name);
+
+ ret = (oh->class->reset) ? oh->class->reset(oh) : _ocp_softreset(oh);
+
+ return ret;
+}
+
+/**
* _omap_hwmod_enable - enable an omap_hwmod
* @oh: struct omap_hwmod *
*
@@ -364,7 +364,7 @@ struct omap_hwmod_omap4_prcm {
* when module is enabled, rather than the default, which is to
* enable autoidle
* HWMOD_SET_DEFAULT_CLOCKACT: program CLOCKACTIVITY bits at startup
- * HWMOD_NO_IDLEST : this module does not have idle status - this is the case
+ * HWMOD_NO_IDLEST: this module does not have idle status - this is the case
* only for few initiator modules on OMAP2 & 3.
* HWMOD_CONTROL_OPT_CLKS_IN_RESET: Enable all optional clocks during reset.
* This is needed for devices like DSS that require optional clocks enabled
@@ -416,6 +416,7 @@ struct omap_hwmod_omap4_prcm {
* @sysc: device SYSCONFIG/SYSSTATUS register data
* @rev: revision of the IP class
* @pre_shutdown: ptr to fn to be executed immediately prior to device shutdown
+ * @reset: ptr to fn to be executed in place of the standard hwmod reset fn
*
* Represent the class of a OMAP hardware "modules" (e.g. timer,
* smartreflex, gpio, uart...)
@@ -427,12 +428,18 @@ struct omap_hwmod_omap4_prcm {
* or some negative error upon failure. Returning an error will cause
* omap_hwmod_shutdown() to abort the device shutdown and return an
* error.
+ *
+ * If @reset is defined, then the function it points to will be
+ * executed in place of the standard hwmod _reset() code in
+ * mach-omap2/omap_hwmod.c. This is needed for IP blocks which have
+ * unusual reset sequences - usually processor IP blocks like the IVA.
*/
struct omap_hwmod_class {
const char *name;
struct omap_hwmod_class_sysconfig *sysc;
u32 rev;
int (*pre_shutdown)(struct omap_hwmod *oh);
+ int (*reset)(struct omap_hwmod *oh);
};
/**