diff mbox

[1/2] ARM: dts: am57xx-beagle-x15: Remove pinmux configurations

Message ID 20160902090600.27262-2-nm@ti.com (mailing list archive)
State New, archived
Headers show

Commit Message

Nishanth Menon Sept. 2, 2016, 9:05 a.m. UTC 
pinmuxing for DRA7x/AM57x family of processors need to be done in IO
isolation as part of initial bootloader executed from SRAM. This is
done as part of iodelay configuration sequence and is required due to
the limitations introduced by erratum ID: i869[1] and elaborated in
the Technical Reference Manual[2] 18.4.6.1.7 Isolation Requirements.

Only peripheral that is permitted for dynamic pin mux configuration is
MMC. This is to accommodate the requirements for varied speeds (which
require IO-delay support in kernel as well). Hence with the exception
of MMC, all other pin mux configurations are removed from the dts.

[1] http://www.ti.com/lit/pdf/sprz429
[2] http://www.ti.com/lit/pdf/sprui30

Signed-off-by: Nishanth Menon <nm@ti.com>
---
 arch/arm/boot/dts/am57xx-beagle-x15.dts | 222 +-------------------------------
 1 file changed, 1 insertion(+), 221 deletions(-)

Comments

Sekhar Nori Sept. 2, 2016, 10:18 a.m. UTC | #1 
On Friday 02 September 2016 02:35 PM, Nishanth Menon wrote:
> pinmuxing for DRA7x/AM57x family of processors need to be done in IO
> isolation as part of initial bootloader executed from SRAM. This is
> done as part of iodelay configuration sequence and is required due to
> the limitations introduced by erratum ID: i869[1] and elaborated in
> the Technical Reference Manual[2] 18.4.6.1.7 Isolation Requirements.
> 
> Only peripheral that is permitted for dynamic pin mux configuration is
> MMC. This is to accommodate the requirements for varied speeds (which

Actually its MMC and DCAN. DCAN because of i893 ("DCAN Initialization
Sequence"). But I can see you may have omitted reference to it since
DCAN is not really used on the x15.

Thanks,
Sekhar

--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Nishanth Menon Sept. 2, 2016, 2:52 p.m. UTC | #2 
On 09/02/2016 05:18 AM, Sekhar Nori wrote:
> On Friday 02 September 2016 02:35 PM, Nishanth Menon wrote:
>> pinmuxing for DRA7x/AM57x family of processors need to be done in IO
>> isolation as part of initial bootloader executed from SRAM. This is
>> done as part of iodelay configuration sequence and is required due to
>> the limitations introduced by erratum ID: i869[1] and elaborated in
>> the Technical Reference Manual[2] 18.4.6.1.7 Isolation Requirements.
>>
>> Only peripheral that is permitted for dynamic pin mux configuration is
>> MMC. This is to accommodate the requirements for varied speeds (which
>
> Actually its MMC and DCAN. DCAN because of i893 ("DCAN Initialization
> Sequence"). But I can see you may have omitted reference to it since
> DCAN is not really used on the x15.

True, I should add that for completeness. will do. thanks for catching 
the same.
diff mbox

Patch

diff --git a/arch/arm/boot/dts/am57xx-beagle-x15.dts b/arch/arm/boot/dts/am57xx-beagle-x15.dts
index 9067ca092dc5..ef21da558ea3 100644
--- a/arch/arm/boot/dts/am57xx-beagle-x15.dts
+++ b/arch/arm/boot/dts/am57xx-beagle-x15.dts
@@ -59,8 +59,6 @@ 
 
 	leds {
 		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&leds_pins_default>;
 
 		led0 {
 			label = "beagle-x15:usr0";
@@ -116,9 +114,6 @@ 
 	tpd12s015: encoder {
 		compatible = "ti,tpd12s015";
 
-		pinctrl-names = "default";
-		pinctrl-0 = <&tpd12s015_pins>;
-
 		gpios = <&gpio7 10 GPIO_ACTIVE_HIGH>,	/* gpio7_10, CT CP HPD */
 			<&gpio6 28 GPIO_ACTIVE_HIGH>,	/* gpio6_28, LS OE */
 			<&gpio7 12 GPIO_ACTIVE_HIGH>;	/* gpio7_12/sp1_cs2, HPD */
@@ -173,43 +168,6 @@ 
 };
 
 &dra7_pmx_core {
-	leds_pins_default: leds_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x37a8, PIN_OUTPUT | MUX_MODE14)	/* spi1_d1.gpio7_8 */
-			DRA7XX_CORE_IOPAD(0x37ac, PIN_OUTPUT | MUX_MODE14)	/* spi1_d0.gpio7_9 */
-			DRA7XX_CORE_IOPAD(0x37c0, PIN_OUTPUT | MUX_MODE14)	/* spi2_sclk.gpio7_14 */
-			DRA7XX_CORE_IOPAD(0x37c4, PIN_OUTPUT | MUX_MODE14)	/* spi2_d1.gpio7_15 */
-		>;
-	};
-
-	i2c1_pins_default: i2c1_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3800, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_sda.sda */
-			DRA7XX_CORE_IOPAD(0x3804, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_scl.scl */
-		>;
-	};
-
-	hdmi_pins: pinmux_hdmi_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3808, PIN_INPUT | MUX_MODE1)	/* i2c2_sda.hdmi1_ddc_scl */
-			DRA7XX_CORE_IOPAD(0x380c, PIN_INPUT | MUX_MODE1)	/* i2c2_scl.hdmi1_ddc_sda */
-		>;
-	};
-
-	i2c3_pins_default: i2c3_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x36a4, PIN_INPUT| MUX_MODE10)	/* mcasp1_aclkx.i2c3_sda */
-			DRA7XX_CORE_IOPAD(0x36a8, PIN_INPUT| MUX_MODE10)	/* mcasp1_fsx.i2c3_scl */
-		>;
-	};
-
-	uart3_pins_default: uart3_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x37f8, PIN_INPUT_SLEW | MUX_MODE2) /* uart2_ctsn.uart3_rxd */
-			DRA7XX_CORE_IOPAD(0x37fc, PIN_INPUT_SLEW | MUX_MODE1) /* uart2_rtsn.uart3_txd */
-		>;
-	};
-
 	mmc1_pins_default: mmc1_pins_default {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x376c, PIN_INPUT | MUX_MODE14)	/* mmc1sdcd.gpio219 */
@@ -236,154 +194,9 @@ 
 			DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
 		>;
 	};
-
-	cpsw_pins_default: cpsw_pins_default {
-		pinctrl-single,pins = <
-			/* Slave 1 */
-			DRA7XX_CORE_IOPAD(0x3650, PIN_OUTPUT | MUX_MODE0)	/* rgmii1_tclk */
-			DRA7XX_CORE_IOPAD(0x3654, PIN_OUTPUT | MUX_MODE0)	/* rgmii1_tctl */
-			DRA7XX_CORE_IOPAD(0x3658, PIN_OUTPUT | MUX_MODE0)	/* rgmii1_td3 */
-			DRA7XX_CORE_IOPAD(0x365c, PIN_OUTPUT | MUX_MODE0)	/* rgmii1_td2 */
-			DRA7XX_CORE_IOPAD(0x3660, PIN_OUTPUT | MUX_MODE0)	/* rgmii1_td1 */
-			DRA7XX_CORE_IOPAD(0x3664, PIN_OUTPUT | MUX_MODE0)	/* rgmii1_td0 */
-			DRA7XX_CORE_IOPAD(0x3668, PIN_INPUT | MUX_MODE0)	/* rgmii1_rclk */
-			DRA7XX_CORE_IOPAD(0x366c, PIN_INPUT | MUX_MODE0)	/* rgmii1_rctl */
-			DRA7XX_CORE_IOPAD(0x3670, PIN_INPUT | MUX_MODE0)	/* rgmii1_rd3 */
-			DRA7XX_CORE_IOPAD(0x3674, PIN_INPUT | MUX_MODE0)	/* rgmii1_rd2 */
-			DRA7XX_CORE_IOPAD(0x3678, PIN_INPUT | MUX_MODE0)	/* rgmii1_rd1 */
-			DRA7XX_CORE_IOPAD(0x367c, PIN_INPUT | MUX_MODE0)	/* rgmii1_rd0 */
-
-			/* Slave 2 */
-			DRA7XX_CORE_IOPAD(0x3598, PIN_OUTPUT | MUX_MODE3)	/* rgmii2_tclk */
-			DRA7XX_CORE_IOPAD(0x359c, PIN_OUTPUT | MUX_MODE3)	/* rgmii2_tctl */
-			DRA7XX_CORE_IOPAD(0x35a0, PIN_OUTPUT | MUX_MODE3)	/* rgmii2_td3 */
-			DRA7XX_CORE_IOPAD(0x35a4, PIN_OUTPUT | MUX_MODE3)	/* rgmii2_td2 */
-			DRA7XX_CORE_IOPAD(0x35a8, PIN_OUTPUT | MUX_MODE3)	/* rgmii2_td1 */
-			DRA7XX_CORE_IOPAD(0x35ac, PIN_OUTPUT | MUX_MODE3)	/* rgmii2_td0 */
-			DRA7XX_CORE_IOPAD(0x35b0, PIN_INPUT | MUX_MODE3)	/* rgmii2_rclk */
-			DRA7XX_CORE_IOPAD(0x35b4, PIN_INPUT | MUX_MODE3)	/* rgmii2_rctl */
-			DRA7XX_CORE_IOPAD(0x35b8, PIN_INPUT | MUX_MODE3)	/* rgmii2_rd3 */
-			DRA7XX_CORE_IOPAD(0x35bc, PIN_INPUT | MUX_MODE3)	/* rgmii2_rd2 */
-			DRA7XX_CORE_IOPAD(0x35c0, PIN_INPUT | MUX_MODE3)	/* rgmii2_rd1 */
-			DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT | MUX_MODE3)	/* rgmii2_rd0 */
-		>;
-
-	};
-
-	cpsw_pins_sleep: cpsw_pins_sleep {
-		pinctrl-single,pins = <
-			/* Slave 1 */
-			DRA7XX_CORE_IOPAD(0x3650, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3654, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3658, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x365c, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3660, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3664, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3668, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x366c, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3670, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3674, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3678, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x367c, PIN_INPUT | MUX_MODE15)
-
-			/* Slave 2 */
-			DRA7XX_CORE_IOPAD(0x3598, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x359c, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35a0, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35a4, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35a8, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35ac, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35b0, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35b4, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35b8, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35bc, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35c0, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT | MUX_MODE15)
-		>;
-	};
-
-	davinci_mdio_pins_default: davinci_mdio_pins_default {
-		pinctrl-single,pins = <
-			/* MDIO */
-			DRA7XX_CORE_IOPAD(0x363c, PIN_OUTPUT_PULLUP | MUX_MODE0)	/* mdio_mclk */
-			DRA7XX_CORE_IOPAD(0x3640, PIN_INPUT_PULLUP | MUX_MODE0)	/* mdio_d */
-		>;
-	};
-
-	davinci_mdio_pins_sleep: davinci_mdio_pins_sleep {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x363c, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3640, PIN_INPUT | MUX_MODE15)
-		>;
-	};
-
-	tps659038_pins_default: tps659038_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3818, PIN_INPUT_PULLUP | MUX_MODE14)	/* wakeup0.gpio1_0 */
-		>;
-	};
-
-	tmp102_pins_default: tmp102_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x37c8, PIN_INPUT_PULLUP | MUX_MODE14)	/* spi2_d0.gpio7_16 */
-		>;
-	};
-
-	mcp79410_pins_default: mcp79410_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3824, PIN_INPUT_PULLUP | MUX_MODE1)	/* wakeup3.sys_nirq1 */
-		>;
-	};
-
-	usb1_pins: pinmux_usb1_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3680, PIN_INPUT_SLEW | MUX_MODE0) /* usb1_drvvbus */
-		>;
-	};
-
-	tpd12s015_pins: pinmux_tpd12s015_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x37b0, PIN_OUTPUT | MUX_MODE14)		/* gpio7_10 CT_CP_HPD */
-			DRA7XX_CORE_IOPAD(0x37b8, PIN_INPUT_PULLDOWN | MUX_MODE14)	/* gpio7_12 HPD */
-			DRA7XX_CORE_IOPAD(0x3770, PIN_OUTPUT | MUX_MODE14)		/* gpio6_28 LS_OE */
-		>;
-	};
-
-	clkout2_pins_default: clkout2_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3694, PIN_OUTPUT_PULLDOWN | MUX_MODE9)	/* xref_clk0.clkout2 */
-		>;
-	};
-
-	clkout2_pins_sleep: clkout2_pins_sleep {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3694, PIN_INPUT | MUX_MODE15)	/* xref_clk0.clkout2 */
-		>;
-	};
-
-	mcasp3_pins_default: mcasp3_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3724, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_aclkx.mcasp3_aclkx */
-			DRA7XX_CORE_IOPAD(0x3728, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_fsx.mcasp3_fsx */
-			DRA7XX_CORE_IOPAD(0x372c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr0.mcasp3_axr0 */
-			DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr1.mcasp3_axr1 */
-		>;
-	};
-
-	mcasp3_pins_sleep: mcasp3_pins_sleep {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3724, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3728, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x372c, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT | MUX_MODE15)
-		>;
-	};
 };
-
 &i2c1 {
 	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c1_pins_default>;
 	clock-frequency = <400000>;
 
 	tps659038: tps659038@58 {
@@ -392,9 +205,6 @@ 
 		interrupt-parent = <&gpio1>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 
-		pinctrl-names = "default";
-		pinctrl-0 = <&tps659038_pins_default>;
-
 		#interrupt-cells = <2>;
 		interrupt-controller;
 
@@ -556,8 +366,6 @@ 
 	tmp102: tmp102@48 {
 		compatible = "ti,tmp102";
 		reg = <0x48>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&tmp102_pins_default>;
 		interrupt-parent = <&gpio7>;
 		interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
 		#thermal-sensor-cells = <1>;
@@ -567,9 +375,6 @@ 
 		#sound-dai-cells = <0>;
 		compatible = "ti,tlv320aic3104";
 		reg = <0x18>;
-		pinctrl-names = "default", "sleep";
-		pinctrl-0 = <&clkout2_pins_default>;
-		pinctrl-1 = <&clkout2_pins_sleep>;
 		assigned-clocks = <&clkoutmux2_clk_mux>;
 		assigned-clock-parents = <&sys_clk2_dclk_div>;
 
@@ -590,8 +395,6 @@ 
 
 &i2c3 {
 	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c3_pins_default>;
 	clock-frequency = <400000>;
 
 	mcp_rtc: rtc@6f {
@@ -601,9 +404,6 @@ 
 				      <&dra7_pmx_core 0x424>;
 		interrupt-names = "irq", "wakeup";
 
-		pinctrl-names = "default";
-		pinctrl-0 = <&mcp79410_pins_default>;
-
 		vcc-supply = <&vdd_3v3>;
 		wakeup-source;
 	};
@@ -623,16 +423,10 @@ 
 	status = "okay";
 	interrupts-extended = <&crossbar_mpu GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
 			      <&dra7_pmx_core 0x3f8>;
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart3_pins_default>;
 };
 
 &mac {
 	status = "okay";
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&cpsw_pins_default>;
-	pinctrl-1 = <&cpsw_pins_sleep>;
 	dual_emac;
 };
 
@@ -648,12 +442,6 @@ 
 	dual_emac_res_vlan = <2>;
 };
 
-&davinci_mdio {
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&davinci_mdio_pins_default>;
-	pinctrl-1 = <&davinci_mdio_pins_sleep>;
-};
-
 &mmc1 {
 	status = "okay";
 
@@ -669,7 +457,7 @@ 
 	status = "okay";
 
 	pinctrl-names = "default";
-	pinctrl-0 = <&mmc2_pins_default>;
+	pinctrl-0 = <&mmc1_pins_default>;
 
 	vmmc-supply = <&vdd_3v3>;
 	bus-width = <8>;
@@ -691,8 +479,6 @@ 
 
 &usb1 {
 	dr_mode = "host";
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb1_pins>;
 };
 
 &omap_dwc3_2 {
@@ -768,9 +554,6 @@ 
 	status = "ok";
 	vdda-supply = <&ldo4_reg>;
 
-	pinctrl-names = "default";
-	pinctrl-0 = <&hdmi_pins>;
-
 	port {
 		hdmi_out: endpoint {
 			remote-endpoint = <&tpd12s015_in>;
@@ -784,9 +567,6 @@ 
 
 &mcasp3 {
 	#sound-dai-cells = <0>;
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&mcasp3_pins_default>;
-	pinctrl-1 = <&mcasp3_pins_sleep>;
 	assigned-clocks = <&mcasp3_ahclkx_mux>;
 	assigned-clock-parents = <&sys_clkin2>;
 	status = "okay";