@@ -565,6 +565,7 @@ dtb-$(CONFIG_SOC_AM33XX) += \
am335x-boneblack.dtb \
am335x-boneblack-wireless.dtb \
am335x-bonegreen.dtb \
+ am335x-bonegreen-wireless.dtb \
am335x-chiliboard.dtb \
am335x-cm-t335.dtb \
am335x-evm.dtb \
new file mode 100644
@@ -0,0 +1,126 @@
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "am33xx.dtsi"
+#include "am335x-bone-common.dtsi"
+#include "am335x-bonegreen-common.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ model = "TI AM335x BeagleBone Green Wireless";
+ compatible = "ti,am335x-bone-green-wireless", "ti,am335x-bone-green", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx";
+
+ wlan_en_reg: fixedregulator@2 {
+ compatible = "regulator-fixed";
+ regulator-name = "wlan-en-regulator";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ startup-delay-us= <70000>;
+
+ /* WL_EN */
+ gpio = <&gpio0 26 0>;
+ enable-active-high;
+ };
+};
+
+&am33xx_pinmux {
+ bt_pins: pinmux_bt_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x878, PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_ad12.gpio1_28 BT_EN */
+ >;
+ };
+
+ mmc3_pins: pinmux_mmc3_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x830, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_ad12.mmc2_dat0 */
+ AM33XX_IOPAD(0x834, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_ad13.mmc2_dat1 */
+ AM33XX_IOPAD(0x838, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_ad14.mmc2_dat2 */
+ AM33XX_IOPAD(0x83c, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_ad15.mmc2_dat3 */
+ AM33XX_IOPAD(0x888, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_csn3.mmc2_cmd */
+ AM33XX_IOPAD(0x88c, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_clk.mmc2_clk */
+ >;
+ };
+
+ uart3_pins: pinmux_uart3_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x934, PIN_INPUT_PULLUP | MUX_MODE1) /* gmii1_rxd3.uart3_rxd */
+ AM33XX_IOPAD(0x938, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* gmii1_rxd2.uart3_txd */
+ AM33XX_IOPAD(0x948, PIN_INPUT | MUX_MODE3) /* mdio_data.uart3_ctsn */
+ AM33XX_IOPAD(0x94c, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* mdio_clk.uart3_rtsn */
+ >;
+ };
+
+ wl18xx_pins: pinmux_wl18xx_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x828, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad10.gpio0_26 WL_EN */
+ AM33XX_IOPAD(0x82C, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad11.gpio0_27 WL_IRQ */
+ AM33XX_IOPAD(0x87C, PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_csn0.gpio1_29 LS_BUF_EN */
+ >;
+ };
+};
+
+&mac {
+ status = "disabled";
+};
+
+&mmc3 {
+ dmas = <&edma_xbar 12 0 1
+ &edma_xbar 13 0 2>;
+ dma-names = "tx", "rx";
+ status = "okay";
+ vmmc-supply = <&wlan_en_reg>;
+ bus-width = <4>;
+ non-removable;
+ cap-power-off-card;
+ ti,needs-special-hs-handling;
+ keep-power-in-suspend;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc3_pins &wl18xx_pins>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ wlcore: wlcore@2 {
+ compatible = "ti,wl1835";
+ reg = <2>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <27 IRQ_TYPE_EDGE_RISING>;
+ };
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins &bt_pins>;
+ status = "okay";
+};
+
+&gpio1 {
+ ls_buf_en {
+ gpio-hog;
+ gpios = <29 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "LS_BUF_EN";
+ };
+};
+
+/* BT_AUD_OUT from wl1835 has to be pulled low when WL_EN is activated.*/
+/* in case it isn't, wilink8 ends up in one of the test modes that */
+/* intruces various issues (elp wkaeup timeouts etc.) */
+/* On the BBGW this pin is routed through the level shifter (U21) that */
+/* introduces a pullup on the line and wilink8 ends up in a bad state. */
+/* use a gpio hog to force this pin low. An alternative may be adding */
+/* an external pulldown on U21 pin 4. */
+
+&gpio3 {
+ bt_aud_in {
+ gpio-hog;
+ gpios = <16 GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "MCASP0_AHCLKR";
+ };
+};
SeeedStudio BeagleBone Green Wireless (BBGW) is an expansion of the SeeedStudio Green (BBG) with the Ethernet replaced by a TI wl1835 wireless module. This board can be indentified by the GW1x value after A335BNLT (BBB) in the at24 eeprom: GW1x [aa 55 33 ee 41 33 33 35 42 4e 4c 54 47 57 31 41 |.U3.A335BNLTGW1A|] http://beagleboard.org/green-wireless http://wiki.seeed.cc/BeagleBone_Green_Wireless/ firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware wl18xx mac address: Stored in at24 eeprom at address 5-16: hexdump -e '8/1 "%c"' /sys/bus/i2c/devices/0-0050/eeprom | cut -b 5-16 Signed-off-by: Robert Nelson <robertcnelson@gmail.com> CC: Tony Lindgren <tony@atomide.com> CC: Jason Kridner <jkridner@beagleboard.org> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/am335x-bonegreen-wireless.dts | 126 ++++++++++++++++++++++++ 2 files changed, 127 insertions(+) create mode 100644 arch/arm/boot/dts/am335x-bonegreen-wireless.dts