@@ -881,26 +881,14 @@ static irqreturn_t tusb_musb_interrupt(int irq, void *__hci)
| TUSB_INT_SRC_ID_STATUS_CHNG))
idle_timeout = tusb_otg_ints(musb, int_src, tbase);
- /* TX dma callback must be handled here, RX dma callback is
- * handled in tusb_omap_dma_cb.
+ /*
+ * Just clear the DMA interrupt if it comes as the completion for both
+ * TX and RX is handled by the DMA callback in tusb6010_omap
*/
if ((int_src & TUSB_INT_SRC_TXRX_DMA_DONE)) {
u32 dma_src = musb_readl(tbase, TUSB_DMA_INT_SRC);
- u32 real_dma_src = musb_readl(tbase, TUSB_DMA_INT_MASK);
dev_dbg(musb->controller, "DMA IRQ %08x\n", dma_src);
- real_dma_src = ~real_dma_src & dma_src;
- if (tusb_dma_omap(musb) && real_dma_src) {
- int tx_source = (real_dma_src & 0xffff);
- int i;
-
- for (i = 1; i <= 15; i++) {
- if (tx_source & (1 << i)) {
- dev_dbg(musb->controller, "completing ep%i %s\n", i, "tx");
- musb_dma_completion(musb, i, 1);
- }
- }
- }
musb_writel(tbase, TUSB_DMA_INT_CLEAR, dma_src);
}
@@ -173,13 +173,7 @@ static void tusb_omap_dma_cb(int lch, u16 ch_status, void *data)
channel->status = MUSB_DMA_STATUS_FREE;
- /* Handle only RX callbacks here. TX callbacks must be handled based
- * on the TUSB DMA status interrupt.
- * REVISIT: Use both TUSB DMA status interrupt and OMAP DMA callback
- * interrupt for RX and TX.
- */
- if (!chdat->tx)
- musb_dma_completion(musb, chdat->epnum, chdat->tx);
+ musb_dma_completion(musb, chdat->epnum, chdat->tx);
/* We must terminate short tx transfers manually by setting TXPKTRDY.
* REVISIT: This same problem may occur with other MUSB dma as well.
@@ -463,22 +457,12 @@ tusb_omap_dma_allocate(struct dma_controller *c,
int ret, i;
struct tusb_omap_dma *tusb_dma;
struct musb *musb;
- void __iomem *tbase;
struct dma_channel *channel = NULL;
struct tusb_omap_dma_ch *chdat = NULL;
struct tusb_dma_data *dma_data = NULL;
- u32 reg;
tusb_dma = container_of(c, struct tusb_omap_dma, controller);
musb = tusb_dma->controller.musb;
- tbase = musb->ctrl_base;
-
- reg = musb_readl(tbase, TUSB_DMA_INT_MASK);
- if (tx)
- reg &= ~(1 << hw_ep->epnum);
- else
- reg &= ~(1 << (hw_ep->epnum + 15));
- musb_writel(tbase, TUSB_DMA_INT_MASK, reg);
/* REVISIT: Why does dmareq5 not work? */
if (hw_ep->epnum == 0) {
@@ -547,26 +531,10 @@ static void tusb_omap_dma_release(struct dma_channel *channel)
{
struct tusb_omap_dma_ch *chdat = to_chdat(channel);
struct musb *musb = chdat->musb;
- void __iomem *tbase = musb->ctrl_base;
- u32 reg;
dev_dbg(musb->controller, "ep%i ch%i\n", chdat->epnum,
chdat->dma_data->ch);
- reg = musb_readl(tbase, TUSB_DMA_INT_MASK);
- if (chdat->tx)
- reg |= (1 << chdat->epnum);
- else
- reg |= (1 << (chdat->epnum + 15));
- musb_writel(tbase, TUSB_DMA_INT_MASK, reg);
-
- reg = musb_readl(tbase, TUSB_DMA_INT_CLEAR);
- if (chdat->tx)
- reg |= (1 << chdat->epnum);
- else
- reg |= (1 << (chdat->epnum + 15));
- musb_writel(tbase, TUSB_DMA_INT_CLEAR, reg);
-
channel->status = MUSB_DMA_STATUS_UNKNOWN;
omap_stop_dma(chdat->dma_data->ch);
Handle the DMA TX in a similar way as we do for the RX: in the DMA completion callback. Since we are no longer using DMA completion interrupt for the TX we can as wall keep these interrupts disabled, but keep the handler for debug purposes. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> --- drivers/usb/musb/tusb6010.c | 18 +++--------------- drivers/usb/musb/tusb6010_omap.c | 34 +--------------------------------- 2 files changed, 4 insertions(+), 48 deletions(-)