@@ -444,8 +444,7 @@
vmmc-supply = <&vdd_3v3>;
vqmmc-supply = <&vdd_3v3>;
bus-width = <8>;
- ti,non-removable;
- cap-mmc-dual-data-rate;
+ non-removable;
};
&sata {
@@ -423,7 +423,7 @@
vmmc-supply = <&v3_3d>;
vqmmc-supply = <&v3_3d>;
bus-width = <8>;
- ti,non-removable;
+ non-removable;
max-frequency = <96000000>;
};
@@ -325,6 +325,7 @@
vmmc-supply = <&evm_1v8_sw>;
vqmmc-supply = <&evm_1v8_sw>;
bus-width = <8>;
+ non-removable;
pinctrl-names = "default", "hs", "ddr_1_8v-rev11", "ddr_1_8v", "hs200_1_8v-rev11", "hs200_1_8v";
pinctrl-0 = <&mmc2_pins_default>;
pinctrl-1 = <&mmc2_pins_hs>;
@@ -1066,17 +1066,15 @@
};
mmc1: mmc@4809c000 {
- compatible = "ti,omap4-hsmmc";
+ compatible = "ti,dra7-sdhci";
reg = <0x4809c000 0x400>;
interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "mmc1";
- ti,dual-volt;
- ti,needs-special-reset;
- dmas = <&sdma_xbar 61>, <&sdma_xbar 62>;
- dma-names = "tx", "rx";
status = "disabled";
pbias-supply = <&pbias_mmc_reg>;
max-frequency = <192000000>;
+ cap-sd-highspeed;
+ cap-mmc-highspeed;
};
hdqw1w: 1w@480b2000 {
@@ -1087,15 +1085,14 @@
};
mmc2: mmc@480b4000 {
- compatible = "ti,omap4-hsmmc";
+ compatible = "ti,dra7-sdhci";
reg = <0x480b4000 0x400>;
interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "mmc2";
- ti,needs-special-reset;
- dmas = <&sdma_xbar 47>, <&sdma_xbar 48>;
- dma-names = "tx", "rx";
status = "disabled";
max-frequency = <192000000>;
+ cap-sd-highspeed;
+ cap-mmc-highspeed;
};
mmc3: mmc@480ad000 {
@@ -421,7 +421,7 @@
pinctrl-names = "default";
pinctrl-0 = <&mmc2_pins_default>;
bus-width = <8>;
- ti,non-removable;
+ non-removable;
max-frequency = <192000000>;
};
@@ -307,7 +307,7 @@
&mmc1 {
status = "okay";
vmmc-supply = <&vio_3v3_sd>;
- vmmc_aux-supply = <&ldo4_reg>;
+ vqmmc-supply = <&ldo4_reg>;
bus-width = <4>;
/*
* SDCD signal is not being used here - using the fact that GPIO mode
@@ -324,6 +324,7 @@
vmmc-supply = <&vio_1v8>;
vqmmc-supply = <&vio_1v8>;
bus-width = <8>;
+ non-removable;
pinctrl-names = "default", "hs", "ddr_1_8v", "hs200_1_8v";
pinctrl-0 = <&mmc2_pins_default>;
pinctrl-1 = <&mmc2_pins_default>;
Use sdhci-omap programming model based on the generic sdhci library for programming the first 2 instances of eMMC/SD/SDIO controller. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> --- arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi | 3 +-- arch/arm/boot/dts/am57xx-idk-common.dtsi | 2 +- arch/arm/boot/dts/dra7-evm.dts | 1 + arch/arm/boot/dts/dra7.dtsi | 15 ++++++--------- arch/arm/boot/dts/dra72-evm-common.dtsi | 2 +- arch/arm/boot/dts/dra76-evm.dts | 3 ++- 6 files changed, 12 insertions(+), 14 deletions(-)