| Message ID | 20180307132020.30951-6-kishon@ti.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On 07/03/18 15:20, Kishon Vijay Abraham I wrote: > Though MMC controller can indicate HS200 mode capability (by > using "mmc-hs200-1_8v" dt property), if the IO lines in the board > is connected to 3.3v supply, HS200 mode cannot be supported. > Such boards have "no-1-8-v" property in their dts file. Disable HS200 > mode for boards which have "no-1-8-v" set. > > Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> > --- > drivers/mmc/host/sdhci.c | 1 + > 1 file changed, 1 insertion(+) > > diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c > index 2ededa7f43df..aa8b5ca0d1b0 100644 > --- a/drivers/mmc/host/sdhci.c > +++ b/drivers/mmc/host/sdhci.c > @@ -3672,6 +3672,7 @@ int sdhci_setup_host(struct sdhci_host *host) > if (host->quirks2 & SDHCI_QUIRK2_NO_1_8_V) { > host->caps1 &= ~(SDHCI_SUPPORT_SDR104 | SDHCI_SUPPORT_SDR50 | > SDHCI_SUPPORT_DDR50); > + mmc->caps2 &= ~MMC_CAP2_HS200; Pedantically, shouldn't that be: ~(MMC_CAP2_HS200_1_8V_SDR | MMC_CAP2_HS400_1_8V) We have MMC_CAP2_HSX00_1_2V so maybe we should add: #define MMC_CAP2_HSX00_1_8V (MMC_CAP2_HS200_1_8V_SDR | MMC_CAP2_HS400_1_8V) And then mmc->caps2 &= ~MMC_CAP2_HSX00_1_8V; > } > > /* Any UHS-I mode in caps implies SDR12 and SDR25 support. */ > -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c index 2ededa7f43df..aa8b5ca0d1b0 100644 --- a/drivers/mmc/host/sdhci.c +++ b/drivers/mmc/host/sdhci.c @@ -3672,6 +3672,7 @@ int sdhci_setup_host(struct sdhci_host *host) if (host->quirks2 & SDHCI_QUIRK2_NO_1_8_V) { host->caps1 &= ~(SDHCI_SUPPORT_SDR104 | SDHCI_SUPPORT_SDR50 | SDHCI_SUPPORT_DDR50); + mmc->caps2 &= ~MMC_CAP2_HS200; } /* Any UHS-I mode in caps implies SDR12 and SDR25 support. */
Though MMC controller can indicate HS200 mode capability (by using "mmc-hs200-1_8v" dt property), if the IO lines in the board is connected to 3.3v supply, HS200 mode cannot be supported. Such boards have "no-1-8-v" property in their dts file. Disable HS200 mode for boards which have "no-1-8-v" set. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> --- drivers/mmc/host/sdhci.c | 1 + 1 file changed, 1 insertion(+)