@@ -515,10 +515,6 @@ int dw_pcie_ep_init(struct dw_pcie_ep *ep)
dev_err(dev, "dbi_base/dbi_base2 is not populated\n");
return -EINVAL;
}
- if (pci->iatu_unroll_enabled && !pci->atu_base) {
- dev_err(dev, "atu_base is not populated\n");
- return -EINVAL;
- }
ret = of_property_read_u32(np, "num-ib-windows", &ep->num_ib_windows);
if (ret < 0) {
@@ -629,17 +629,6 @@ static struct pci_ops dw_pcie_ops = {
.write = dw_pcie_wr_conf,
};
-static u8 dw_pcie_iatu_unroll_enabled(struct dw_pcie *pci)
-{
- u32 val;
-
- val = dw_pcie_readl_dbi(pci, PCIE_ATU_VIEWPORT);
- if (val == 0xffffffff)
- return 1;
-
- return 0;
-}
-
void dw_pcie_setup_rc(struct pcie_port *pp)
{
u32 val, ctrl, num_ctrls;
@@ -693,14 +682,6 @@ void dw_pcie_setup_rc(struct pcie_port *pp)
* we should not program the ATU here.
*/
if (!pp->ops->rd_other_conf) {
- /* Get iATU unroll support */
- pci->iatu_unroll_enabled = dw_pcie_iatu_unroll_enabled(pci);
- dev_dbg(pci->dev, "iATU unroll: %s\n",
- pci->iatu_unroll_enabled ? "enabled" : "disabled");
-
- if (pci->iatu_unroll_enabled && !pci->atu_base)
- pci->atu_base = pci->dbi_base + DEFAULT_DBI_ATU_OFFSET;
-
dw_pcie_prog_outbound_atu(pci, PCIE_ATU_REGION_INDEX0,
PCIE_ATU_TYPE_MEM, pp->mem_base,
pp->mem_bus_addr, pp->mem_size);
@@ -339,6 +339,17 @@ int dw_pcie_link_up(struct dw_pcie *pci)
(!(val & PCIE_PHY_DEBUG_R1_LINK_IN_TRAINING)));
}
+static u8 dw_pcie_iatu_unroll_enabled(struct dw_pcie *pci)
+{
+ u32 val;
+
+ val = dw_pcie_readl_dbi(pci, PCIE_ATU_VIEWPORT);
+ if (val == 0xffffffff)
+ return 1;
+
+ return 0;
+}
+
void dw_pcie_setup(struct dw_pcie *pci)
{
int ret;
@@ -347,6 +358,14 @@ void dw_pcie_setup(struct dw_pcie *pci)
struct device *dev = pci->dev;
struct device_node *np = dev->of_node;
+ /* Get iATU unroll support */
+ pci->iatu_unroll_enabled = dw_pcie_iatu_unroll_enabled(pci);
+ dev_dbg(pci->dev, "iATU unroll: %s\n",
+ pci->iatu_unroll_enabled ? "enabled" : "disabled");
+
+ if (pci->iatu_unroll_enabled && !pci->atu_base)
+ pci->atu_base = pci->dbi_base + DEFAULT_DBI_ATU_OFFSET;
+
ret = of_property_read_u32(np, "num-lanes", &lanes);
if (ret)
lanes = 0;
iatu_unroll_enabled flag is set only for Designware in host mode. However iATU unroll can be applicable for endpoint mode too. Set iatu_unroll_enabled flag in dw_pcie_setup which is common for both host mode and endpoint mode. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> --- .../pci/controller/dwc/pcie-designware-ep.c | 4 ---- .../pci/controller/dwc/pcie-designware-host.c | 19 ------------------- drivers/pci/controller/dwc/pcie-designware.c | 19 +++++++++++++++++++ 3 files changed, 19 insertions(+), 23 deletions(-)