@@ -27,16 +27,14 @@ cpcap_adc: adc {
cpcap_battery: battery {
compatible = "motorola,cpcap-battery";
- interrupts-extended = <
- &cpcap 6 0 &cpcap 5 0 &cpcap 3 0
- &cpcap 20 0 &cpcap 54 0 &cpcap 57 0
- >;
+ interrupts-extended =
+ <&cpcap 6 0>, <&cpcap 5 0>, <&cpcap 3 0>,
+ <&cpcap 20 0>, <&cpcap 54 0>, <&cpcap 57 0>;
interrupt-names =
"eol", "lowbph", "lowbpl",
- "chrgcurr1", "battdetb",
- "cccal";
- io-channels = <&cpcap_adc 0 &cpcap_adc 1
- &cpcap_adc 5 &cpcap_adc 6>;
+ "chrgcurr1", "battdetb", "cccal";
+ io-channels = <&cpcap_adc 0>, <&cpcap_adc 1>,
+ <&cpcap_adc 5>, <&cpcap_adc 6>;
io-channel-names = "battdetb", "battp",
"chg_isense", "batti";
power-supplies = <&cpcap_charger>;
@@ -44,20 +42,19 @@ &cpcap 20 0 &cpcap 54 0 &cpcap 57 0
cpcap_charger: charger {
compatible = "motorola,mapphone-cpcap-charger";
- interrupts-extended = <
- &cpcap 13 0 &cpcap 12 0 &cpcap 29 0 &cpcap 28 0
- &cpcap 22 0 &cpcap 21 0 &cpcap 20 0 &cpcap 19 0
- &cpcap 54 0
- >;
+ interrupts-extended =
+ <&cpcap 13 0>, <&cpcap 12 0>, <&cpcap 29 0>,
+ <&cpcap 28 0>, <&cpcap 22 0>, <&cpcap 21 0>,
+ <&cpcap 20 0>, <&cpcap 19 0>, <&cpcap 54 0>;
interrupt-names =
- "chrg_det", "rvrs_chrg", "chrg_se1b", "se0conn",
- "rvrs_mode", "chrgcurr2", "chrgcurr1", "vbusvld",
- "battdetb";
- mode-gpios = <&gpio3 29 GPIO_ACTIVE_LOW
- &gpio3 23 GPIO_ACTIVE_LOW>;
- io-channels = <&cpcap_adc 0 &cpcap_adc 1
- &cpcap_adc 2 &cpcap_adc 5
- &cpcap_adc 6>;
+ "chrg_det", "rvrs_chrg", "chrg_se1b",
+ "se0conn", "rvrs_mode", "chrgcurr2",
+ "chrgcurr1", "vbusvld", "battdetb";
+ mode-gpios = <&gpio3 29 GPIO_ACTIVE_LOW>,
+ <&gpio3 23 GPIO_ACTIVE_LOW>;
+ io-channels = <&cpcap_adc 0>, <&cpcap_adc 1>,
+ <&cpcap_adc 2>, <&cpcap_adc 5>,
+ <&cpcap_adc 6>;
io-channel-names = "battdetb", "battp",
"vbus", "chg_isense",
"batti";
@@ -98,22 +95,22 @@ power_button: button {
cpcap_usb2_phy: phy {
compatible = "motorola,mapphone-cpcap-usb-phy";
- pinctrl-0 = <&usb_gpio_mux_sel1 &usb_gpio_mux_sel2>;
+ pinctrl-0 = <&usb_gpio_mux_sel1>, <&usb_gpio_mux_sel2>;
pinctrl-1 = <&usb_ulpi_pins>;
pinctrl-2 = <&usb_utmi_pins>;
pinctrl-3 = <&uart3_pins>;
pinctrl-names = "default", "ulpi", "utmi", "uart";
#phy-cells = <0>;
- interrupts-extended = <
- &cpcap 15 0 &cpcap 14 0 &cpcap 28 0 &cpcap 19 0
- &cpcap 18 0 &cpcap 17 0 &cpcap 16 0 &cpcap 49 0
- &cpcap 48 0
- >;
+ interrupts-extended =
+ <&cpcap 15 0>, <&cpcap 14 0>, <&cpcap 28 0>,
+ <&cpcap 19 0>, <&cpcap 18 0>, <&cpcap 17 0>,
+ <&cpcap 16 0>, <&cpcap 49 0>, <&cpcap 48 0>;
interrupt-names =
- "id_ground", "id_float", "se0conn", "vbusvld",
- "sessvld", "sessend", "se1", "dm", "dp";
- mode-gpios = <&gpio2 28 GPIO_ACTIVE_HIGH
- &gpio1 0 GPIO_ACTIVE_HIGH>;
+ "id_ground", "id_float", "se0conn",
+ "vbusvld", "sessvld", "sessend",
+ "se1", "dm", "dp";
+ mode-gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>,
+ <&gpio1 0 GPIO_ACTIVE_HIGH>;
io-channels = <&cpcap_adc 2>, <&cpcap_adc 7>;
io-channel-names = "vbus", "id";
vusb-supply = <&vusb>;
'<&gpio1 parameters &gpio2 parameters>' and '<&gpio1 parameters>, <&gpio2 parameters>' result in the same DTB, but second format has better source code readability. Also 'dtbs_check' currently uses this format to determine the amount of items specified, so using this syntax is needed to successfully verify the devicetree source against a DT schema format. Cc: Tony Lindgren <tony@atomide.com> Cc: linux-omap@vger.kernel.org Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> --- .../arm/boot/dts/motorola-cpcap-mapphone.dtsi | 59 +++++++++---------- 1 file changed, 28 insertions(+), 31 deletions(-)