@@ -434,6 +434,84 @@ pruss_tm: target-module@54400000 {
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x0 0x54400000 0x80000>;
+
+ pruss1: pruss@0 {
+ compatible = "ti,am4376-pruss1";
+ reg = <0x0 0x40000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ pruss1_mem: memories@0 {
+ reg = <0x0 0x2000>,
+ <0x2000 0x2000>,
+ <0x10000 0x8000>;
+ reg-names = "dram0", "dram1",
+ "shrdram2";
+ };
+
+ pruss1_cfg: cfg@26000 {
+ compatible = "ti,pruss-cfg", "syscon";
+ reg = <0x26000 0x2000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0x26000 0x2000>;
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pruss1_iepclk_mux: iepclk-mux@30 {
+ reg = <0x30>;
+ #clock-cells = <0>;
+ clocks = <&sysclk_div>, /* icss_iep_gclk */
+ <&pruss_ocp_gclk>; /* icss_ocp_gclk */
+ };
+ };
+ };
+
+ pruss1_mii_rt: mii-rt@32000 {
+ compatible = "ti,pruss-mii", "syscon";
+ reg = <0x32000 0x58>;
+ };
+
+ pruss1_intc: interrupt-controller@20000 {
+ compatible = "ti,pruss-intc";
+ reg = <0x20000 0x2000>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "host_intr0", "host_intr1",
+ "host_intr2", "host_intr3",
+ "host_intr4",
+ "host_intr6", "host_intr7";
+ ti,irqs-reserved = /bits/ 8 <0x20>; /* BIT(5) */
+ };
+
+ pru1_0: pru@34000 {
+ compatible = "ti,am4376-pru";
+ reg = <0x34000 0x3000>,
+ <0x22000 0x400>,
+ <0x22400 0x100>;
+ reg-names = "iram", "control", "debug";
+ firmware-name = "am437x-pru1_0-fw";
+ };
+
+ pru1_1: pru@38000 {
+ compatible = "ti,am4376-pru";
+ reg = <0x38000 0x3000>,
+ <0x24000 0x400>,
+ <0x24400 0x100>;
+ reg-names = "iram", "control", "debug";
+ firmware-name = "am437x-pru1_1-fw";
+ };
+ };
};
target-module@50000000 {
Add the DT node for the PRU-ICSS1 instance on the AM437x family of SoCs. Each PRU-ICSS instance is represented by a pruss node and other child nodes. The nodes are added under the interconnect target module node in the common am4372 dtsi file. The PRU-ICSS instances are supported only on AM4376+ SoCs though in the AM437x family, so the interconnect target module node should be disabled in any derivative board dts file that uses AM4372 SoCs. The PRU-ICSS1 on AM437x is very similar to the PRUSS in AM33xx, except for variations in the RAM sizes, bus addresses and the number of interrupts coming into the MPU INTC (host interrupt 5 is routed to the other PRUSS instead of MPU). The PRUSS subsystem node contains the entire address space. The various sub-modules of the PRU-ICSS are represented as individual child nodes (so platform devices themselves) of the PRUSS subsystem node. These include the two PRU cores and the interrupt controller. All the Data RAMs are represented within a child node of its own named 'memories' without any compatible. The Real Time Media Independent Interface controller (MII_RT), and the CFG sub-module are represented as syscon nodes. The PRUSS CFG module has a clock mux for IEP clock, this clk node is added under the CFG child node 'clocks'. The default source for this mux clock is the PRU_ICSS_IEP_GCLK clock. The DT nodes use all standard properties. The regs property in the PRU nodes define the addresses for the Instruction RAM, the Debug and Control sub-modules for that PRU core. The firmware for each PRU core is defined through a 'firmware-name' property. The default names for the firmware images for each PRU core are defined as follows (these can be adjusted either in derivative board dts files or through sysfs at runtime if required): PRU-ICSS1 PRU0 Core: am437x-pru1_0-fw PRU-ICSS1 PRU1 Core: am437x-pru1_1-fw Note: 1. There are few more sub-modules like the Industrial Ethernet Peripheral (IEP), MDIO, UART, eCAP that do not have bindings and so will be added in the future. 2. The PRUSS INTC on AM437x SoCs also connect the host interrupt 0 to ADC0 and ADC1; 6 and 7 as possible DMA events, so use the 'ti,irqs-reserved' property in derivative board dts files _if_ any of them should not be handled by the host OS. Host interrupt 5 is already marked reserved as it is connected to the other PRUSS instance. Signed-off-by: Suman Anna <s-anna@ti.com> --- arch/arm/boot/dts/am4372.dtsi | 78 +++++++++++++++++++++++++++++++++++ 1 file changed, 78 insertions(+)