@@ -10,7 +10,6 @@
*/
#include <linux/delay.h>
-#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <linux/gpio/consumer.h>
#include <linux/module.h>
@@ -33,7 +32,6 @@ enum {
struct rx51_audio_pdata {
struct gpio_desc *tvout_selection_gpio;
- struct gpio_desc *jack_detection_gpio;
struct gpio_desc *eci_sw_gpio;
struct gpio_desc *speaker_amp_gpio;
};
@@ -198,7 +196,7 @@ static struct snd_soc_jack rx51_av_jack;
static struct snd_soc_jack_gpio rx51_av_jack_gpios[] = {
{
- .name = "avdet-gpio",
+ .name = "jack-detection",
.report = SND_JACK_HEADSET,
.invert = 1,
.debounce_time = 200,
@@ -263,7 +261,6 @@ static const struct snd_kcontrol_new aic34_rx51_controls[] = {
static int rx51_aic34_init(struct snd_soc_pcm_runtime *rtd)
{
struct snd_soc_card *card = rtd->card;
- struct rx51_audio_pdata *pdata = snd_soc_card_get_drvdata(card);
int err;
snd_soc_limit_volume(card, "TPA6130A2 Headphone Playback Volume", 42);
@@ -283,9 +280,9 @@ static int rx51_aic34_init(struct snd_soc_pcm_runtime *rtd)
return err;
}
- /* prepare gpio for snd_soc_jack_add_gpios */
- rx51_av_jack_gpios[0].gpio = desc_to_gpio(pdata->jack_detection_gpio);
- devm_gpiod_put(card->dev, pdata->jack_detection_gpio);
+ rx51_av_jack_gpios[0].gpiod_dev = card->dev;
+ /* Name is assigned in the struct */
+ rx51_av_jack_gpios[0].idx = 0;
err = snd_soc_jack_add_gpios(&rx51_av_jack,
ARRAY_SIZE(rx51_av_jack_gpios),
@@ -425,14 +422,6 @@ static int rx51_soc_probe(struct platform_device *pdev)
return PTR_ERR(pdata->tvout_selection_gpio);
}
- pdata->jack_detection_gpio = devm_gpiod_get(card->dev,
- "jack-detection",
- GPIOD_ASIS);
- if (IS_ERR(pdata->jack_detection_gpio)) {
- dev_err(card->dev, "could not get jack detection gpio\n");
- return PTR_ERR(pdata->jack_detection_gpio);
- }
-
pdata->eci_sw_gpio = devm_gpiod_get(card->dev, "eci-switch",
GPIOD_OUT_HIGH);
if (IS_ERR(pdata->eci_sw_gpio)) {
The RX51/Nokia n900 uses the legacy GPIO header to convert a GPIO back to the global GPIO numberspace and then the jack using it in the snd_soc_jack_add_gpios() call immediately looks up the corresponding descriptor again. The snd_soc_jack_add_gpios() handles GPIOs passed with devices just fine: pass in the device instead, and rename the GPIO to match the property in the device tree, and it should work all the same but without all the trouble. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> --- sound/soc/ti/rx51.c | 19 ++++--------------- 1 file changed, 4 insertions(+), 15 deletions(-)