@@ -22,9 +22,8 @@ struct pxa_cpu_pm_fns {
extern struct pxa_cpu_pm_fns *pxa_cpu_pm_fns;
/* sleep.S */
-extern void pxa25x_cpu_suspend(unsigned int);
-extern void pxa27x_cpu_suspend(unsigned int);
-extern void pxa_cpu_resume(void);
+extern void pxa25x_cpu_suspend(unsigned int, long);
+extern void pxa27x_cpu_suspend(unsigned int, long);
extern int pxa_pm_enter(suspend_state_t state);
extern int pxa_pm_prepare(void);
@@ -212,7 +212,7 @@ static unsigned long store_ptr;
static int palmz72_pm_suspend(struct sys_device *dev, pm_message_t msg)
{
/* setup the resume_info struct for the original bootloader */
- palmz72_resume_info.resume_addr = (u32) pxa_cpu_resume;
+ palmz72_resume_info.resume_addr = (u32) cpu_resume;
/* Storing memory touched by ROM */
store_ptr = *PALMZ72_SAVE_DWORD;
@@ -67,11 +67,6 @@ int pxa_pm_enter(suspend_state_t state)
EXPORT_SYMBOL_GPL(pxa_pm_enter);
-unsigned long sleep_phys_sp(void *sp)
-{
- return virt_to_phys(sp);
-}
-
static int pxa_pm_valid(suspend_state_t state)
{
if (pxa_cpu_pm_fns)
@@ -244,7 +244,7 @@ static void pxa25x_cpu_pm_enter(suspend_state_t state)
switch (state) {
case PM_SUSPEND_MEM:
- pxa25x_cpu_suspend(PWRMODE_SLEEP);
+ pxa25x_cpu_suspend(PWRMODE_SLEEP, PLAT_PHYS_OFFSET - PAGE_OFFSET);
break;
}
}
@@ -252,7 +252,7 @@ static void pxa25x_cpu_pm_enter(suspend_state_t state)
static int pxa25x_cpu_pm_prepare(void)
{
/* set resume return address */
- PSPR = virt_to_phys(pxa_cpu_resume);
+ PSPR = virt_to_phys(cpu_resume);
return 0;
}
@@ -300,7 +300,7 @@ void pxa27x_cpu_pm_enter(suspend_state_t state)
pxa_cpu_standby();
break;
case PM_SUSPEND_MEM:
- pxa27x_cpu_suspend(pwrmode);
+ pxa27x_cpu_suspend(pwrmode, PLAT_PHYS_OFFSET - PAGE_OFFSET);
break;
}
}
@@ -313,7 +313,7 @@ static int pxa27x_cpu_pm_valid(suspend_state_t state)
static int pxa27x_cpu_pm_prepare(void)
{
/* set resume return address */
- PSPR = virt_to_phys(pxa_cpu_resume);
+ PSPR = virt_to_phys(cpu_resume);
return 0;
}
@@ -142,8 +142,7 @@ static void pxa3xx_cpu_pm_suspend(void)
volatile unsigned long *p = (volatile void *)0xc0000000;
unsigned long saved_data = *p;
- extern void pxa3xx_cpu_suspend(void);
- extern void pxa3xx_cpu_resume(void);
+ extern void pxa3xx_cpu_suspend(long);
/* resuming from D2 requires the HSIO2/BOOT/TPM clocks enabled */
CKENA |= (1 << CKEN_BOOT) | (1 << CKEN_TPM);
@@ -161,9 +160,9 @@ static void pxa3xx_cpu_pm_suspend(void)
PSPR = 0x5c014000;
/* overwrite with the resume address */
- *p = virt_to_phys(pxa3xx_cpu_resume);
+ *p = virt_to_phys(cpu_resume);
- pxa3xx_cpu_suspend();
+ pxa3xx_cpu_suspend(PLAT_PHYS_OFFSET - PAGE_OFFSET);
*p = saved_data;
@@ -22,133 +22,26 @@
.text
-pxa_cpu_save_cp:
- @ get coprocessor registers
- mrc p14, 0, r3, c6, c0, 0 @ clock configuration, for turbo mode
- mrc p15, 0, r4, c15, c1, 0 @ CP access reg
- mrc p15, 0, r5, c13, c0, 0 @ PID
- mrc p15, 0, r6, c3, c0, 0 @ domain ID
- mrc p15, 0, r7, c2, c0, 0 @ translation table base addr
- mrc p15, 0, r8, c1, c1, 0 @ auxiliary control reg
- mrc p15, 0, r9, c1, c0, 0 @ control reg
-
- bic r3, r3, #2 @ clear frequency change bit
-
- @ store them plus current virtual stack ptr on stack
- mov r10, sp
- stmfd sp!, {r3 - r10}
-
- mov pc, lr
-
-pxa_cpu_save_sp:
- @ preserve phys address of stack
- mov r0, sp
- str lr, [sp, #-4]!
- bl sleep_phys_sp
- ldr r1, =sleep_save_sp
- str r0, [r1]
- ldr pc, [sp], #4
-
#ifdef CONFIG_PXA3xx
/*
* pxa3xx_cpu_suspend() - forces CPU into sleep state (S2D3C4)
*
- * NOTE: unfortunately, pxa_cpu_save_cp can not be reused here since
- * the auxiliary control register address is different between pxa3xx
- * and pxa{25x,27x}
+ * r0 = v:p offset
*/
-
ENTRY(pxa3xx_cpu_suspend)
#ifndef CONFIG_IWMMXT
mra r2, r3, acc0
#endif
stmfd sp!, {r2 - r12, lr} @ save registers on stack
-
- mrc p14, 0, r3, c6, c0, 0 @ clock configuration, for turbo mode
- mrc p15, 0, r4, c15, c1, 0 @ CP access reg
- mrc p15, 0, r5, c13, c0, 0 @ PID
- mrc p15, 0, r6, c3, c0, 0 @ domain ID
- mrc p15, 0, r7, c2, c0, 0 @ translation table base addr
- mrc p15, 0, r8, c1, c0, 1 @ auxiliary control reg
- mrc p15, 0, r9, c1, c0, 0 @ control reg
-
- bic r3, r3, #2 @ clear frequency change bit
-
- @ store them plus current virtual stack ptr on stack
- mov r10, sp
- stmfd sp!, {r3 - r10}
-
- @ store physical address of stack pointer
- mov r0, sp
- bl sleep_phys_sp
- ldr r1, =sleep_save_sp
- str r0, [r1]
-
- @ clean data cache
- bl xsc3_flush_kern_cache_all
+ mov r1, r0
+ ldr r3, =pxa_cpu_resume @ resume function
+ bl cpu_suspend
mov r0, #0x06 @ S2D3C4 mode
mcr p14, 0, r0, c7, c0, 0 @ enter sleep
20: b 20b @ waiting for sleep
-
- .data
- .align 5
-/*
- * pxa3xx_cpu_resume
- */
-
-ENTRY(pxa3xx_cpu_resume)
-
- mov r0, #PSR_I_BIT | PSR_F_BIT | SVC_MODE @ set SVC, irqs off
- msr cpsr_c, r0
-
- ldr r0, sleep_save_sp @ stack phys addr
- ldmfd r0, {r3 - r9, sp} @ CP regs + virt stack ptr
-
- mov r1, #0
- mcr p15, 0, r1, c7, c7, 0 @ invalidate I & D caches, BTB
- mcr p15, 0, r1, c7, c10, 4 @ drain write (&fill) buffer
- mcr p15, 0, r1, c7, c5, 4 @ flush prefetch buffer
- mcr p15, 0, r1, c8, c7, 0 @ invalidate I & D TLBs
-
- mcr p14, 0, r3, c6, c0, 0 @ clock configuration, turbo mode.
- mcr p15, 0, r4, c15, c1, 0 @ CP access reg
- mcr p15, 0, r5, c13, c0, 0 @ PID
- mcr p15, 0, r6, c3, c0, 0 @ domain ID
- mcr p15, 0, r7, c2, c0, 0 @ translation table base addr
- mcr p15, 0, r8, c1, c0, 1 @ auxiliary control reg
-
- @ temporarily map resume_turn_on_mmu into the page table,
- @ otherwise prefetch abort occurs after MMU is turned on
- mov r1, r7
- bic r1, r1, #0x00ff
- bic r1, r1, #0x3f00
- ldr r2, =0x542e
-
- adr r3, resume_turn_on_mmu
- mov r3, r3, lsr #20
- orr r4, r2, r3, lsl #20
- ldr r5, [r1, r3, lsl #2]
- str r4, [r1, r3, lsl #2]
-
- @ Mapping page table address in the page table
- mov r6, r1, lsr #20
- orr r7, r2, r6, lsl #20
- ldr r8, [r1, r6, lsl #2]
- str r7, [r1, r6, lsl #2]
-
- ldr r2, =pxa3xx_resume_after_mmu @ absolute virtual address
- b resume_turn_on_mmu @ cache align execution
-
- .text
-pxa3xx_resume_after_mmu:
- /* restore the temporary mapping */
- str r5, [r1, r3, lsl #2]
- str r8, [r1, r6, lsl #2]
- b resume_after_mmu
-
#endif /* CONFIG_PXA3xx */
#ifdef CONFIG_PXA27x
@@ -158,28 +51,23 @@ pxa3xx_resume_after_mmu:
* Forces CPU into sleep state.
*
* r0 = value for PWRMODE M field for desired sleep state
+ * r1 = v:p offset
*/
-
ENTRY(pxa27x_cpu_suspend)
#ifndef CONFIG_IWMMXT
mra r2, r3, acc0
#endif
stmfd sp!, {r2 - r12, lr} @ save registers on stack
-
- bl pxa_cpu_save_cp
-
- mov r5, r0 @ save sleep mode
- bl pxa_cpu_save_sp
-
- @ clean data cache
- bl xscale_flush_kern_cache_all
+ mov r4, r0 @ save sleep mode
+ ldr r3, =pxa_cpu_resume @ resume function
+ bl cpu_suspend
@ Put the processor to sleep
@ (also workaround for sighting 28071)
@ prepare value for sleep mode
- mov r1, r5 @ sleep mode
+ mov r1, r4 @ sleep mode
@ prepare pointer to physical address 0 (virtual mapping in generic.c)
mov r2, #UNCACHED_PHYS_0
@@ -216,21 +104,16 @@ ENTRY(pxa27x_cpu_suspend)
* Forces CPU into sleep state.
*
* r0 = value for PWRMODE M field for desired sleep state
+ * r1 = v:p offset
*/
ENTRY(pxa25x_cpu_suspend)
stmfd sp!, {r2 - r12, lr} @ save registers on stack
-
- bl pxa_cpu_save_cp
-
- mov r5, r0 @ save sleep mode
- bl pxa_cpu_save_sp
-
- @ clean data cache
- bl xscale_flush_kern_cache_all
-
+ mov r4, r0 @ save sleep mode
+ ldr r3, =pxa_cpu_resume @ resume function
+ bl cpu_suspend
@ prepare value for sleep mode
- mov r1, r5 @ sleep mode
+ mov r1, r4 @ sleep mode
@ prepare pointer to physical address 0 (virtual mapping in generic.c)
mov r2, #UNCACHED_PHYS_0
@@ -317,53 +200,9 @@ pxa_cpu_do_suspend:
* pxa_cpu_resume()
*
* entry point from bootloader into kernel during resume
- *
- * Note: Yes, part of the following code is located into the .data section.
- * This is to allow sleep_save_sp to be accessed with a relative load
- * while we can't rely on any MMU translation. We could have put
- * sleep_save_sp in the .text section as well, but some setups might
- * insist on it to be truly read-only.
*/
-
- .data
- .align 5
-ENTRY(pxa_cpu_resume)
- mov r0, #PSR_I_BIT | PSR_F_BIT | SVC_MODE @ set SVC, irqs off
- msr cpsr_c, r0
-
- ldr r0, sleep_save_sp @ stack phys addr
- ldr r2, =resume_after_mmu @ its absolute virtual address
- ldmfd r0, {r3 - r9, sp} @ CP regs + virt stack ptr
-
- mov r1, #0
- mcr p15, 0, r1, c8, c7, 0 @ invalidate I & D TLBs
- mcr p15, 0, r1, c7, c7, 0 @ invalidate I & D caches, BTB
-
- mcr p14, 0, r3, c6, c0, 0 @ clock configuration, turbo mode.
- mcr p15, 0, r4, c15, c1, 0 @ CP access reg
- mcr p15, 0, r5, c13, c0, 0 @ PID
- mcr p15, 0, r6, c3, c0, 0 @ domain ID
- mcr p15, 0, r7, c2, c0, 0 @ translation table base addr
- mcr p15, 0, r8, c1, c1, 0 @ auxiliary control reg
- b resume_turn_on_mmu @ cache align execution
-
.align 5
-resume_turn_on_mmu:
- mcr p15, 0, r9, c1, c0, 0 @ turn on MMU, caches, etc.
-
- @ Let us ensure we jump to resume_after_mmu only when the mcr above
- @ actually took effect. They call it the "cpwait" operation.
- mrc p15, 0, r0, c2, c0, 0 @ queue a dependency on CP15
- sub pc, r2, r0, lsr #32 @ jump to virtual addr
- nop
- nop
- nop
-
-sleep_save_sp:
- .word 0 @ preserve stack phys ptr here
-
- .text
-resume_after_mmu:
+pxa_cpu_resume:
ldmfd sp!, {r2, r3}
#ifndef CONFIG_IWMMXT
mar acc0, r2, r3
@@ -676,7 +676,7 @@ static struct pxa2xx_udc_mach_info zeus_udc_info = {
static void zeus_power_off(void)
{
local_irq_disable();
- pxa27x_cpu_suspend(PWRMODE_DEEPSLEEP);
+ pxa27x_cpu_suspend(PWRMODE_DEEPSLEEP, PLAT_PHYS_OFFSET - PAGE_OFFSET);
}
#else
#define zeus_power_off NULL