@@ -303,6 +303,34 @@ static void serial_omap_start_tx(struct uart_port *port)
pm_runtime_put_autosuspend(up->dev);
}
+static void serial_omap_throttle(struct uart_port *port)
+{
+ struct uart_omap_port *up = to_uart_omap_port(port);
+ unsigned long flags;
+
+ pm_runtime_get_sync(up->dev);
+ spin_lock_irqsave(&up->port.lock, flags);
+ up->ier &= ~(UART_IER_RLSI | UART_IER_RDI);
+ serial_out(up, UART_IER, up->ier);
+ spin_unlock_irqrestore(&up->port.lock, flags);
+ pm_runtime_mark_last_busy(up->dev);
+ pm_runtime_put_autosuspend(up->dev);
+}
+
+static void serial_omap_unthrottle(struct uart_port *port)
+{
+ struct uart_omap_port *up = to_uart_omap_port(port);
+ unsigned long flags;
+
+ pm_runtime_get_sync(up->dev);
+ spin_lock_irqsave(&up->port.lock, flags);
+ up->ier |= UART_IER_RLSI | UART_IER_RDI;
+ serial_out(up, UART_IER, up->ier);
+ spin_unlock_irqrestore(&up->port.lock, flags);
+ pm_runtime_mark_last_busy(up->dev);
+ pm_runtime_put_autosuspend(up->dev);
+}
+
static unsigned int check_modem_status(struct uart_omap_port *up)
{
unsigned int status;
@@ -1000,6 +1028,7 @@ static void serial_omap_config_port(struct uart_port *port, int flags)
dev_dbg(up->port.dev, "serial_omap_config_port+%d\n",
up->port.line);
up->port.type = PORT_OMAP;
+ up->port.flags |= UPF_SOFT_FLOW | UPF_HARD_FLOW;
}
static int
@@ -1203,6 +1232,8 @@ static struct uart_ops serial_omap_pops = {
.get_mctrl = serial_omap_get_mctrl,
.stop_tx = serial_omap_stop_tx,
.start_tx = serial_omap_start_tx,
+ .throttle = serial_omap_throttle,
+ .unthrottle = serial_omap_unthrottle,
.stop_rx = serial_omap_stop_rx,
.enable_ms = serial_omap_enable_ms,
.break_ctl = serial_omap_break_ctl,
When the UART device has hardware flow control enabled, it ignores the MCR RTS bit in the MCR register, and keeps RTS asserted as long as we continue to read characters from the UART receiver FIFO. This means that when the TTY buffers become full, the UART doesn't tell the remote end to stop sending, which causes the TTY layer to start dropping characters. A similar problem exists with software flow control. We need the FIFO register to fill when software flow control is enabled to provoke the UART to send the XOFF character. Fix this by implementing the throttle/unthrottle callbacks, and use these to disable receiver interrupts. This in turn means that the UART FIFO will fill, which will then cause the UART's hardware to deassert the RTS signal and/or send the XOFF character, stopping the remote end. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> --- drivers/tty/serial/omap-serial.c | 31 +++++++++++++++++++++++++++++++ 1 files changed, 31 insertions(+), 0 deletions(-)