[2/2] OMAP: convert boards that use SMSC911x to use gpmc-smsc911x

Message ID	b6ee61df13950e143ff09d47ba790a6194214225.1302992702.git.mike@compulab.co.il (mailing list archive)
State	Accepted
Commit	6629398945426f388d61392eecd733336a6316a4
Delegated to:	Tony Lindgren
Headers	show Received: from vger.kernel.org (vger.kernel.org [209.132.180.67]) by demeter1.kernel.org (8.14.4/8.14.3) with ESMTP id p3GN0WA2021151 for <patchwork-omap@patchwork.kernel.org>; Sat, 16 Apr 2011 23:01:18 GMT From: Mike Rapoport <mike@compulab.co.il> To: Tony Lindgren <tony@atomide.com> Cc: linux-omap@vger.kernel.org, Mike Rapoport <mike@compulab.co.il> Subject: [PATCH 2/2] OMAP: convert boards that use SMSC911x to use gpmc-smsc911x Date: Sun, 17 Apr 2011 01:29:30 +0300 Message-Id: <b6ee61df13950e143ff09d47ba790a6194214225.1302992702.git.mike@compulab.co.il> In-Reply-To: <cover.1302992702.git.mike@compulab.co.il> References: <cover.1302992702.git.mike@compulab.co.il> Sender: linux-omap-owner@vger.kernel.org Precedence: bulk

diff --git a/arch/arm/mach-omap2/board-cm-t35.c b/arch/arm/mach-omap2/board-cm-t35.c index 02a12b4..b5772c1 100644 --- a/arch/arm/mach-omap2/board-cm-t35.c +++ b/arch/arm/mach-omap2/board-cm-t35.c @@ -66,86 +66,26 @@ #if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE) #include <linux/smsc911x.h> +#include <plat/gpmc-smsc911x.h> -static struct smsc911x_platform_config cm_t35_smsc911x_config = { - .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW, - .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN, +static struct omap_smsc911x_platform_data cm_t35_smsc911x_cfg = { + .cs = CM_T35_SMSC911X_CS, + .gpio_irq = CM_T35_SMSC911X_GPIO, + .gpio_reset = -EINVAL, .flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS, - .phy_interface = PHY_INTERFACE_MODE_MII, }; -static struct resource cm_t35_smsc911x_resources[] = { - { - .flags = IORESOURCE_MEM, - }, - { - .start = OMAP_GPIO_IRQ(CM_T35_SMSC911X_GPIO), - .end = OMAP_GPIO_IRQ(CM_T35_SMSC911X_GPIO), - .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL, - }, -}; - -static struct platform_device cm_t35_smsc911x_device = { - .name = "smsc911x", - .id = 0, - .num_resources = ARRAY_SIZE(cm_t35_smsc911x_resources), - .resource = cm_t35_smsc911x_resources, - .dev = { - .platform_data = &cm_t35_smsc911x_config, - }, -}; - -static struct resource sb_t35_smsc911x_resources[] = { - { - .flags = IORESOURCE_MEM, - }, - { - .start = OMAP_GPIO_IRQ(SB_T35_SMSC911X_GPIO), - .end = OMAP_GPIO_IRQ(SB_T35_SMSC911X_GPIO), - .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL, - }, -}; - -static struct platform_device sb_t35_smsc911x_device = { - .name = "smsc911x", - .id = 1, - .num_resources = ARRAY_SIZE(sb_t35_smsc911x_resources), - .resource = sb_t35_smsc911x_resources, - .dev = { - .platform_data = &cm_t35_smsc911x_config, - }, +static struct omap_smsc911x_platform_data sb_t35_smsc911x_cfg = { + .cs = SB_T35_SMSC911X_CS, + .gpio_irq = SB_T35_SMSC911X_GPIO, + .gpio_reset = -EINVAL, + .flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS, }; -static void __init cm_t35_init_smsc911x(struct platform_device *dev, - int cs, int irq_gpio) -{ - unsigned long cs_mem_base; - - if (gpmc_cs_request(cs, SZ_16M, &cs_mem_base) < 0) { - pr_err("CM-T35: Failed request for GPMC mem for smsc911x\n"); - return; - } - - dev->resource[0].start = cs_mem_base + 0x0; - dev->resource[0].end = cs_mem_base + 0xff; - - if ((gpio_request(irq_gpio, "ETH IRQ") == 0) && - (gpio_direction_input(irq_gpio) == 0)) { - gpio_export(irq_gpio, 0); - } else { - pr_err("CM-T35: could not obtain gpio for SMSC911X IRQ\n"); - return; - } - - platform_device_register(dev); -} - static void __init cm_t35_init_ethernet(void) { - cm_t35_init_smsc911x(&cm_t35_smsc911x_device, - CM_T35_SMSC911X_CS, CM_T35_SMSC911X_GPIO); - cm_t35_init_smsc911x(&sb_t35_smsc911x_device, - SB_T35_SMSC911X_CS, SB_T35_SMSC911X_GPIO); + gpmc_smsc911x_init(&cm_t35_smsc911x_cfg); + gpmc_smsc911x_init(&sb_t35_smsc911x_cfg); } #else static inline void __init cm_t35_init_ethernet(void) { return; } diff --git a/arch/arm/mach-omap2/board-igep0020.c b/arch/arm/mach-omap2/board-igep0020.c index 5f8a2fd..bb60414 100644 --- a/arch/arm/mach-omap2/board-igep0020.c +++ b/arch/arm/mach-omap2/board-igep0020.c @@ -192,57 +192,18 @@ static void __init igep2_flash_init(void) {} #if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE) #include <linux/smsc911x.h> +#include <plat/gpmc-smsc911x.h> -static struct smsc911x_platform_config igep2_smsc911x_config = { - .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW, - .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN, - .flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS , - .phy_interface = PHY_INTERFACE_MODE_MII, -}; - -static struct resource igep2_smsc911x_resources[] = { - { - .flags = IORESOURCE_MEM, - }, - { - .start = OMAP_GPIO_IRQ(IGEP2_SMSC911X_GPIO), - .end = OMAP_GPIO_IRQ(IGEP2_SMSC911X_GPIO), - .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL, - }, -}; - -static struct platform_device igep2_smsc911x_device = { - .name = "smsc911x", - .id = 0, - .num_resources = ARRAY_SIZE(igep2_smsc911x_resources), - .resource = igep2_smsc911x_resources, - .dev = { - .platform_data = &igep2_smsc911x_config, - }, +static struct omap_smsc911x_platform_data smsc911x_cfg = { + .cs = IGEP2_SMSC911X_CS, + .gpio_irq = IGEP2_SMSC911X_GPIO, + .gpio_reset = -EINVAL, + .flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS, }; static inline void __init igep2_init_smsc911x(void) { - unsigned long cs_mem_base; - - if (gpmc_cs_request(IGEP2_SMSC911X_CS, SZ_16M, &cs_mem_base) < 0) { - pr_err("IGEP v2: Failed request for GPMC mem for smsc911x\n"); - gpmc_cs_free(IGEP2_SMSC911X_CS); - return; - } - - igep2_smsc911x_resources[0].start = cs_mem_base + 0x0; - igep2_smsc911x_resources[0].end = cs_mem_base + 0xff; - - if ((gpio_request(IGEP2_SMSC911X_GPIO, "SMSC911X IRQ") == 0) && - (gpio_direction_input(IGEP2_SMSC911X_GPIO) == 0)) { - gpio_export(IGEP2_SMSC911X_GPIO, 0); - } else { - pr_err("IGEP v2: Could not obtain gpio for for SMSC911X IRQ\n"); - return; - } - - platform_device_register(&igep2_smsc911x_device); + gpmc_smsc911x_init(&smsc911x_cfg); } #else diff --git a/arch/arm/mach-omap2/board-ldp.c b/arch/arm/mach-omap2/board-ldp.c index e2ba779..ea9f049 100644 --- a/arch/arm/mach-omap2/board-ldp.c +++ b/arch/arm/mach-omap2/board-ldp.c @@ -43,6 +43,7 @@ #include <asm/delay.h> #include <plat/usb.h> +#include <plat/gpmc-smsc911x.h> #include "board-flash.h" #include "mux.h" @@ -54,36 +55,6 @@ #define DEBUG_BASE 0x08000000 #define LDP_ETHR_START DEBUG_BASE -static struct resource ldp_smsc911x_resources[] = { - [0] = { - .start = LDP_ETHR_START, - .end = LDP_ETHR_START + SZ_4K, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = 0, - .end = 0, - .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL, - }, -}; - -static struct smsc911x_platform_config ldp_smsc911x_config = { - .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW, - .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN, - .flags = SMSC911X_USE_32BIT, - .phy_interface = PHY_INTERFACE_MODE_MII, -}; - -static struct platform_device ldp_smsc911x_device = { - .name = "smsc911x", - .id = -1, - .num_resources = ARRAY_SIZE(ldp_smsc911x_resources), - .resource = ldp_smsc911x_resources, - .dev = { - .platform_data = &ldp_smsc911x_config, - }, -}; - static uint32_t board_keymap[] = { KEY(0, 0, KEY_1), KEY(1, 0, KEY_2), @@ -246,33 +217,16 @@ static struct spi_board_info ldp_spi_board_info[] __initdata = { }, }; +static struct omap_smsc911x_platform_data smsc911x_cfg = { + .cs = LDP_SMSC911X_CS, + .gpio_irq = LDP_SMSC911X_GPIO, + .gpio_reset = -EINVAL, + .flags = SMSC911X_USE_32BIT, +}; + static inline void __init ldp_init_smsc911x(void) { - int eth_cs; - unsigned long cs_mem_base; - int eth_gpio = 0; - - eth_cs = LDP_SMSC911X_CS; - - if (gpmc_cs_request(eth_cs, SZ_16M, &cs_mem_base) < 0) { - printk(KERN_ERR "Failed to request GPMC mem for smsc911x\n"); - return; - } - - ldp_smsc911x_resources[0].start = cs_mem_base + 0x0; - ldp_smsc911x_resources[0].end = cs_mem_base + 0xff; - udelay(100); - - eth_gpio = LDP_SMSC911X_GPIO; - - ldp_smsc911x_resources[1].start = OMAP_GPIO_IRQ(eth_gpio); - - if (gpio_request(eth_gpio, "smsc911x irq") < 0) { - printk(KERN_ERR "Failed to request GPIO%d for smsc911x IRQ\n", - eth_gpio); - return; - } - gpio_direction_input(eth_gpio); + gpmc_smsc911x_init(&smsc911x_cfg); } static struct platform_device ldp_lcd_device = { @@ -389,7 +343,6 @@ static struct omap2_hsmmc_info mmc[] __initdata = { }; static struct platform_device *ldp_devices[] __initdata = { - &ldp_smsc911x_device, &ldp_lcd_device, &ldp_gpio_keys_device, }; diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c index 5a1a916..3fc85c6 100644 --- a/arch/arm/mach-omap2/board-omap3evm.c +++ b/arch/arm/mach-omap2/board-omap3evm.c @@ -101,49 +101,20 @@ static void __init omap3_evm_get_revision(void) } #if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE) -static struct resource omap3evm_smsc911x_resources[] = { - [0] = { - .start = OMAP3EVM_ETHR_START, - .end = (OMAP3EVM_ETHR_START + OMAP3EVM_ETHR_SIZE - 1), - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = OMAP_GPIO_IRQ(OMAP3EVM_ETHR_GPIO_IRQ), - .end = OMAP_GPIO_IRQ(OMAP3EVM_ETHR_GPIO_IRQ), - .flags = (IORESOURCE_IRQ | IRQF_TRIGGER_LOW), - }, -}; +#include <plat/gpmc-smsc911x.h> -static struct smsc911x_platform_config smsc911x_config = { - .phy_interface = PHY_INTERFACE_MODE_MII, - .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW, - .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN, - .flags = (SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS), -}; - -static struct platform_device omap3evm_smsc911x_device = { - .name = "smsc911x", - .id = -1, - .num_resources = ARRAY_SIZE(omap3evm_smsc911x_resources), - .resource = &omap3evm_smsc911x_resources[0], - .dev = { - .platform_data = &smsc911x_config, - }, +static struct omap_smsc911x_platform_data smsc911x_cfg = { + .cs = OMAP3EVM_SMSC911X_CS, + .gpio_irq = OMAP3EVM_ETHR_GPIO_IRQ, + .gpio_reset = -EINVAL, + .flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS, }; static inline void __init omap3evm_init_smsc911x(void) { - int eth_cs, eth_rst; struct clk *l3ck; unsigned int rate; - if (get_omap3_evm_rev() == OMAP3EVM_BOARD_GEN_1) - eth_rst = OMAP3EVM_GEN1_ETHR_GPIO_RST; - else - eth_rst = OMAP3EVM_GEN2_ETHR_GPIO_RST; - - eth_cs = OMAP3EVM_SMSC911X_CS; - l3ck = clk_get(NULL, "l3_ck"); if (IS_ERR(l3ck)) rate = 100000000; @@ -152,33 +123,13 @@ static inline void __init omap3evm_init_smsc911x(void) /* Configure ethernet controller reset gpio */ if (cpu_is_omap3430()) { - if (gpio_request(eth_rst, "SMSC911x gpio") < 0) { - pr_err(KERN_ERR "Failed to request %d for smsc911x\n", - eth_rst); - return; - } - - if (gpio_direction_output(eth_rst, 1) < 0) { - pr_err(KERN_ERR "Failed to set direction of %d for" \ - " smsc911x\n", eth_rst); - return; - } - /* reset pulse to ethernet controller*/ - usleep_range(150, 220); - gpio_set_value(eth_rst, 0); - usleep_range(150, 220); - gpio_set_value(eth_rst, 1); - usleep_range(1, 2); - } - - if (gpio_request(OMAP3EVM_ETHR_GPIO_IRQ, "SMSC911x irq") < 0) { - printk(KERN_ERR "Failed to request GPIO%d for smsc911x IRQ\n", - OMAP3EVM_ETHR_GPIO_IRQ); - return; + if (get_omap3_evm_rev() == OMAP3EVM_BOARD_GEN_1) + smsc911x_cfg.gpio_reset = OMAP3EVM_GEN1_ETHR_GPIO_RST; + else + smsc911x_cfg.gpio_reset = OMAP3EVM_GEN2_ETHR_GPIO_RST; } - gpio_direction_input(OMAP3EVM_ETHR_GPIO_IRQ); - platform_device_register(&omap3evm_smsc911x_device); + gpmc_smsc911x_init(&smsc911x_cfg); } #else diff --git a/arch/arm/mach-omap2/board-omap3stalker.c b/arch/arm/mach-omap2/board-omap3stalker.c index a6e0b91..848016c 100644 --- a/arch/arm/mach-omap2/board-omap3stalker.c +++ b/arch/arm/mach-omap2/board-omap3stalker.c @@ -56,50 +56,25 @@ #include "timer-gp.h" #if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE) +#include <plat/gpmc-smsc911x.h> + #define OMAP3STALKER_ETHR_START 0x2c000000 #define OMAP3STALKER_ETHR_SIZE 1024 #define OMAP3STALKER_ETHR_GPIO_IRQ 19 #define OMAP3STALKER_SMC911X_CS 5 -static struct resource omap3stalker_smsc911x_resources[] = { - [0] = { - .start = OMAP3STALKER_ETHR_START, - .end = - (OMAP3STALKER_ETHR_START + OMAP3STALKER_ETHR_SIZE - 1), - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = OMAP_GPIO_IRQ(OMAP3STALKER_ETHR_GPIO_IRQ), - .end = OMAP_GPIO_IRQ(OMAP3STALKER_ETHR_GPIO_IRQ), - .flags = (IORESOURCE_IRQ | IRQF_TRIGGER_LOW), - }, -}; - -static struct smsc911x_platform_config smsc911x_config = { - .phy_interface = PHY_INTERFACE_MODE_MII, - .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW, - .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN, +static struct omap_smsc911x_platform_data smsc911x_cfg = { + .cs = OMAP3STALKER_SMC911X_CS, + .gpio_irq = OMAP3STALKER_ETHR_GPIO_IRQ, + .gpio_reset = -EINVAL, .flags = (SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS), }; -static struct platform_device omap3stalker_smsc911x_device = { - .name = "smsc911x", - .id = -1, - .num_resources = ARRAY_SIZE(omap3stalker_smsc911x_resources), - .resource = &omap3stalker_smsc911x_resources[0], - .dev = { - .platform_data = &smsc911x_config, - }, -}; - static inline void __init omap3stalker_init_eth(void) { - int eth_cs; struct clk *l3ck; unsigned int rate; - eth_cs = OMAP3STALKER_SMC911X_CS; - l3ck = clk_get(NULL, "l3_ck"); if (IS_ERR(l3ck)) rate = 100000000; @@ -107,16 +82,7 @@ static inline void __init omap3stalker_init_eth(void) rate = clk_get_rate(l3ck); omap_mux_init_gpio(19, OMAP_PIN_INPUT_PULLUP); - if (gpio_request(OMAP3STALKER_ETHR_GPIO_IRQ, "SMC911x irq") < 0) { - printk(KERN_ERR - "Failed to request GPIO%d for smc911x IRQ\n", - OMAP3STALKER_ETHR_GPIO_IRQ); - return; - } - - gpio_direction_input(OMAP3STALKER_ETHR_GPIO_IRQ); - - platform_device_register(&omap3stalker_smsc911x_device); + gpmc_smsc911x_init(&smsc911x_cfg); } #else diff --git a/arch/arm/mach-omap2/board-overo.c b/arch/arm/mach-omap2/board-overo.c index 59ca333..4016166 100644 --- a/arch/arm/mach-omap2/board-overo.c +++ b/arch/arm/mach-omap2/board-overo.c @@ -146,106 +146,26 @@ static inline void __init overo_ads7846_init(void) { return; } #if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE) #include <linux/smsc911x.h> +#include <plat/gpmc-smsc911x.h> -static struct resource overo_smsc911x_resources[] = { - { - .name = "smsc911x-memory", - .flags = IORESOURCE_MEM, - }, - { - .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL, - }, -}; - -static struct resource overo_smsc911x2_resources[] = { - { - .name = "smsc911x2-memory", - .flags = IORESOURCE_MEM, - }, - { - .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL, - }, +static struct omap_smsc911x_platform_data smsc911x_cfg = { + .cs = OVERO_SMSC911X_CS, + .gpio_irq = OVERO_SMSC911X_GPIO, + .gpio_reset = -EINVAL, + .flags = SMSC911X_USE_32BIT, }; -static struct smsc911x_platform_config overo_smsc911x_config = { - .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW, - .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN, - .flags = SMSC911X_USE_32BIT , - .phy_interface = PHY_INTERFACE_MODE_MII, +static struct omap_smsc911x_platform_data smsc911x2_cfg = { + .cs = OVERO_SMSC911X2_CS, + .gpio_irq = OVERO_SMSC911X2_GPIO, + .gpio_reset = -EINVAL, + .flags = SMSC911X_USE_32BIT, }; -static struct platform_device overo_smsc911x_device = { - .name = "smsc911x", - .id = 0, - .num_resources = ARRAY_SIZE(overo_smsc911x_resources), - .resource = overo_smsc911x_resources, - .dev = { - .platform_data = &overo_smsc911x_config, - }, -}; - -static struct platform_device overo_smsc911x2_device = { - .name = "smsc911x", - .id = 1, - .num_resources = ARRAY_SIZE(overo_smsc911x2_resources), - .resource = overo_smsc911x2_resources, - .dev = { - .platform_data = &overo_smsc911x_config, - }, -}; - -static struct platform_device *smsc911x_devices[] = { - &overo_smsc911x_device, - &overo_smsc911x2_device, -}; - -static inline void __init overo_init_smsc911x(void) +static void __init overo_init_smsc911x(void) { - unsigned long cs_mem_base, cs_mem_base2; - - /* set up first smsc911x chip */ - - if (gpmc_cs_request(OVERO_SMSC911X_CS, SZ_16M, &cs_mem_base) < 0) { - printk(KERN_ERR "Failed request for GPMC mem for smsc911x\n"); - return; - } - - overo_smsc911x_resources[0].start = cs_mem_base + 0x0; - overo_smsc911x_resources[0].end = cs_mem_base + 0xff; - - if ((gpio_request(OVERO_SMSC911X_GPIO, "SMSC911X IRQ") == 0) && - (gpio_direction_input(OVERO_SMSC911X_GPIO) == 0)) { - gpio_export(OVERO_SMSC911X_GPIO, 0); - } else { - printk(KERN_ERR "could not obtain gpio for SMSC911X IRQ\n"); - return; - } - - overo_smsc911x_resources[1].start = OMAP_GPIO_IRQ(OVERO_SMSC911X_GPIO); - overo_smsc911x_resources[1].end = 0; - - /* set up second smsc911x chip */ - - if (gpmc_cs_request(OVERO_SMSC911X2_CS, SZ_16M, &cs_mem_base2) < 0) { - printk(KERN_ERR "Failed request for GPMC mem for smsc911x2\n"); - return; - } - - overo_smsc911x2_resources[0].start = cs_mem_base2 + 0x0; - overo_smsc911x2_resources[0].end = cs_mem_base2 + 0xff; - - if ((gpio_request(OVERO_SMSC911X2_GPIO, "SMSC911X2 IRQ") == 0) && - (gpio_direction_input(OVERO_SMSC911X2_GPIO) == 0)) { - gpio_export(OVERO_SMSC911X2_GPIO, 0); - } else { - printk(KERN_ERR "could not obtain gpio for SMSC911X2 IRQ\n"); - return; - } - - overo_smsc911x2_resources[1].start = OMAP_GPIO_IRQ(OVERO_SMSC911X2_GPIO); - overo_smsc911x2_resources[1].end = 0; - - platform_add_devices(smsc911x_devices, ARRAY_SIZE(smsc911x_devices)); + gpmc_smsc911x_init(&smsc911x_cfg); + gpmc_smsc911x_init(&smsc911x2_cfg); } #else diff --git a/arch/arm/mach-omap2/board-zoom-debugboard.c b/arch/arm/mach-omap2/board-zoom-debugboard.c index 007ebdc..2ee9ab9 100644 --- a/arch/arm/mach-omap2/board-zoom-debugboard.c +++ b/arch/arm/mach-omap2/board-zoom-debugboard.c @@ -15,6 +15,7 @@ #include <linux/interrupt.h> #include <plat/gpmc.h> +#include <plat/gpmc-smsc911x.h> #include <mach/board-zoom.h> @@ -26,60 +27,16 @@ #define DEBUG_BASE 0x08000000 #define ZOOM_ETHR_START DEBUG_BASE -static struct resource zoom_smsc911x_resources[] = { - [0] = { - .start = ZOOM_ETHR_START, - .end = ZOOM_ETHR_START + SZ_4K, - .flags = IORESOURCE_MEM, - }, - [1] = { - .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL, - }, -}; - -static struct smsc911x_platform_config zoom_smsc911x_config = { - .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW, - .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN, +static struct omap_smsc911x_platform_data zoom_smsc911x_cfg = { + .cs = ZOOM_SMSC911X_CS, + .gpio_irq = ZOOM_SMSC911X_GPIO, + .gpio_reset = -EINVAL, .flags = SMSC911X_USE_32BIT, - .phy_interface = PHY_INTERFACE_MODE_MII, -}; - -static struct platform_device zoom_smsc911x_device = { - .name = "smsc911x", - .id = -1, - .num_resources = ARRAY_SIZE(zoom_smsc911x_resources), - .resource = zoom_smsc911x_resources, - .dev = { - .platform_data = &zoom_smsc911x_config, - }, }; static inline void __init zoom_init_smsc911x(void) { - int eth_cs; - unsigned long cs_mem_base; - int eth_gpio = 0; - - eth_cs = ZOOM_SMSC911X_CS; - - if (gpmc_cs_request(eth_cs, SZ_16M, &cs_mem_base) < 0) { - printk(KERN_ERR "Failed to request GPMC mem for smsc911x\n"); - return; - } - - zoom_smsc911x_resources[0].start = cs_mem_base + 0x0; - zoom_smsc911x_resources[0].end = cs_mem_base + 0xff; - - eth_gpio = ZOOM_SMSC911X_GPIO; - - zoom_smsc911x_resources[1].start = OMAP_GPIO_IRQ(eth_gpio); - - if (gpio_request(eth_gpio, "smsc911x irq") < 0) { - printk(KERN_ERR "Failed to request GPIO%d for smsc911x IRQ\n", - eth_gpio); - return; - } - gpio_direction_input(eth_gpio); + gpmc_smsc911x_init(&zoom_smsc911x_cfg); } static struct plat_serial8250_port serial_platform_data[] = { @@ -150,7 +107,6 @@ static inline int omap_zoom_debugboard_detect(void) } static struct platform_device *zoom_devices[] __initdata = { - &zoom_smsc911x_device, &zoom_debugboard_serial_device, };

[2/2] OMAP: convert boards that use SMSC911x to use gpmc-smsc911x

Commit Message

Patch